Search Documents

By T Walkemeyer, R Elliott, D Chang-Martin

Over the past decade, discrete element method (DEM) simulations have seen increasing adoption by the resources sector to inform the design of materials handling equipment such as transfer chutes, bins and hoppers. But, if ‘all models are wrong, but some are useful’ (Box, 1979) what approaches are available to check that a DEM simulation is useful? How to avoid garbage in equals garbage out. This work considers what properties of bulk solid flow behaviour are important to transfer chute simulation. Cohesive bulk solids (such as sticky iron ore fines) can develop sufficient strength to form a stable cohesive arch, this phenomenon is not well predicted by measurements of angle of repose. This work presents a two-part approach to the development of a useful DEM model that can be used to add value to the design and optimisation of bulk materials handling equipment. Part 1 is the calibration of not just one, but a range of material models chosen to envelope the range of anticipated materials that will be handled. This work describes the DEM simulation of a batch of direct shear cell tests to develop material models that can be measured by the same metrics routinely used to characterise the flowability of cohesive iron ore fines. Part 2 of this work describes systematic methods for validation of the transfer chute DEM simulations. The DEM model is only useful if it can adequately represent the typical problems observed within a transfer chute, such as blockages due to build-up and cohesive arching. Proper validation requires good observations. Validation examples of site observations are shown side-byside with simulations to demonstrate the adequacy of the DEM model and calibration approach. DEM simulations have the potential to add significant value by allowing engineers and designers to predict material flow-through equipment based on a range of material properties, allowing for stress testing designs and making iterative improvements.

Sep 18, 2023

By J E. Powalisz

Obtaining a representative sample of bulk materials in process industries is critical to providing valid data for process control and custody transfer (valuation). The accuracy of a sample, that is to say how well the sample represents the material in the process, is directly related to how well the process can be controlled and to how much a product may be worth. Sampling accuracy then is in fact related to bottom line profitability.Sampling theory offers information and equations on how to take a representative sample from a process, however, the actual practice of extracting a sample from the process can be more of an art.Key sampling variables include product specifications such as bulk density, particle distribution, material conveyance, practical sampler location, sampler type and sample frequency and volume/mass.This paper discusses basic sampling theory, sampling methods, types of samplers, how to develop a ‘real world’ sampling system and current manual and automated samplers.Key points include ‘practical precision and variance’, material properties, flow properties, direct sampling versus indirect sampling, sampler types and applications.CITATION:Powalisz, J E, 2014. Bulk solids sampling, in Proceedings Sampling 2014 , pp 179–188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By M, C A. RosiFre, R C. Figueiredo e Silva

Jaspilites and underlying basalt contacts of the Archaean volcano- sedimentary Grpo Parß Group, Carajßs, host giant iron mineralisation in the ~100-km long, E-W trending Carajßs fold. Preliminary, unpublished geochronological data point to a Palaeoproterozoic mineralisation event. Geochemically, jaspilites are typical volcanogenic banded iron formations. Basalts exhibit evidence of spilitic seawater interaction. Iron-associated hydrothermal alteration of mafic rocks was induced by fluid infiltration in amygdales, with development of chlorite- and hematite-dominated zones. In the case of jaspilites, iron mineralisation encompasses: partial replacement of jaspilitic microcrystalline hematite by blasts of martitic magnetite; jasper recrystallisation, producing fine-grained, hematite-free granoblastic quartz; martite recrystallisation, forming lobate¦subhedral hematite; pervasive porosity development by quartz-chert leaching; incipient cavity filling by microlamellar hematite; and advanced filling by coarser, euhedral and comb-textured, tabular- shaped hematite.Peak hydrothermal ore textures indicate typical epithermal-crust conditions, supported by preliminary fluid-inclusion calculations at 160 - 200¦C. Such temperatures and extreme fluid-to-rock ratios during alteration must have exceeded the ambient metamorphic conditions, with the infiltrating fluid relatively hot and capable of leaching SiO2. Therefore, mineralisation developed over exhumed, Archaean, brittly deformed rocks, with mineral associations representative of very low- to low-grade metamorphism. Considering that chlorite (¦talc) abounds in mafic rocks; hydrothermal albite is developed; dolomite fills veins and vugs; the typical rare-earth-element (REE) pattern of jaspilites is significantly modified in higher-grade hard hematite ores (higher LREE); pyrite, copper sulfide minerals and rare gold occur in association with carbonate-quartz-rich alteration zones, it is suggested that an alkaline, H2O-Fe-CO2 mineralising fluid dominated, also containing species like S¦Cu¦Au. Peak-mineralising conditions are likely to have resulted from a single, evolving fluid, via incipient- through advanced-stage alteration phases. The porous, high-grade soft hematite-type ore (SH), rich in microlamellar and anhedral hematite, must have derived from interaction with this relatively hot SiO2-leaching fluid, whereas the high-grade massive hard hematite-type ore (MH) developed due to closer fluid-rock temperature equilibrium conditions, attained by mineral reactions, with relative increase in the Fe/Σcations ratios allowing the precipitation of subhedral-tabular hematite that partially cements the soft-hematite ore. SH and MH hematite ore types must thus reflect intermediate and high fluid:rock ratios, respectively. Since the N5 deposit is to date understood to contain the largest amount of the MH ore, its units are interpreted as the loci of the highest fluid:rock ratios in the district. Preliminary mineralogical information regarding the S11 deposit of the Serra Sul (south range) implies higher-temperature conditions. The near-equant grain size and the granoblastic intergrain relationship, coupled with the presence of riebeckite, augitic pyroxene and garnet, suggest hornfels textures. The data collected, though still relatively sparse, permit the speculation that the immense driving force for the Carajßs world-class iron deposits was a relatively shallow, igneous-related hydrothermal system. If such a model is correct, then the Carajßs Palaeoproterozoic iron deposits could represent an end-member of the iron oxide-copper-gold hydrothermal system in the province.

Jan 1, 2005

By G Chitumbura

Raise boring is a critical aspect of mining at Xstrata Copper’s Mount Isa Copper Operations (MICO). MICO’s internal raise boring department regularly develops ventilation rises, orepasses and stope cut-off rises and reams approximately 2500 m per annum. Developed, trialled and implemented as standard practice over the past two years, procedural changes in constructing the raise bore machine’s foundations have significantly reduced operator exposure to raise boring’s inherent risks of working around open holes and manual handling. An additional cost benefit of this newly-adopted procedure is derived from reducing the likelihood of damaging the machine while de-rigging.When conforming to standard industry raise boring practices, exposure to an open hole begins when the reamer breaks through the concrete pad and ends when it is removed from the hole – a process which, depending on the size of the hole and the raise boring machine, can take up to three days to complete. Although wearing fall restraint equipment, operators working on and around the raise bore machine during de-rigging are continually exposed to the risk of falling from heights. In contrast, MICO’s newly-developed and successfully-implemented presink raise boring system reduces this exposure to a maximum of four hours, regardless of hole size. Exposure to manual handling hazards is also substantially reduced as the presink procedure eliminates manual placement of a 100 kg drill bit under the machine to commence pilot-hole drilling. Outcomes of implementing the presink System at MICO have been so beneficial that it is now standard procedure for all reaming in excess of 1 m diameters.

Mar 21, 2011

By Hawkins L. V, Seedsman K

A combined reflection seismic and magnetic survey off the south coast of New South Wales has revealed six distinct reflection horizons within the Lower Triassic- Upper Permian sequence, and has enabled the upper part of the Illawarra Coal Measures to be mapped in considerable detail. Large magnetic anomalies in the eastern half of the survey area appear to originate in the Gerringong Volcanic Sequence which forms the magnetic basement in this survey. Small residual anomalies in the western half of the area can be correlated with small scale faulting and folding in the uppert part of the Illawarra Coal Measures, as revealed by the seismic reflection survey. A synclinal axis striking at approximately 55¦ has been mapped near the western margin of the survey area, and areas of faulting and folding have been outlined by com- bined analysis of seismic and magnetic results.

Jan 1, 1969

Responsibility for the administration of mineral resources is divided between federal and provincial governments. The paper traces the evolution of mineral policies at both levels of government, from the end of World War II to the present. In the immediate post-World War II years, the emphasis was on supplying the raw material needs of a rapidly growing world economy. Policies favouring growth and development of the Canadian mining industry were instituted during this period. Two decades of uninterrupted expansion (the 1950s and 1960s) ensued. The decade of the 1970s was a turbulent one for Canadian mineral producers. Governments intervened more substantially than ever before. Moreover, the industry suffered from an intense period of competition for resource revenues by the two levels of government. At the same time, far reaching changes were taking place in the structure of world mineral markets. To date in the 1980s, the mineral industry has, perforce, adapted to existing mineral market structures. Mineral policies, too, have shown signs of adapting to the needs of the mineral industry. Whether the resulting mix of policies will permit the revitalization of the Canadian mining sector remains to be seen.

Jan 1, 1986

Underground mine ventilation is now com monly simulated on a digital computer. Such a programme, incorporating natural ventilation has been modified by others to account for methane emission and elevated local tempera- tures. At Wollongong University, the pro- gramme was further developed and extensive interactive graphics incorporated such that any view of the three dimensional mine could be viewed, and superimposed upon that view are areas where a nominated parameter has exceeded a particular value - generally at a nominated time after a particular event and usually a fire/explosion of one type or another. A further programme was developed such that up to 20 'times' could be examined at a particu- lar location after say, a fuel rich fire at some other place in the mine. The output from this programme includes a plot of methane 1, smoke 1, temperature, pressure and air flow versus time - a most useful graphic to observe the limits of safe attendance in a particular Airway.

Jan 1, 1983

By Y M. Wang, W Z. Liu, L F. Li, X L. Zhang

Based on the blasting crater theory, the equation between k under typical cases and burden line, charge height was obtained by open pit bench blasting analysis model. The model was calculated with mine production blasting. The blastability coefficient k and the best range of blasting burden line were specially emphasised on determination of lateral crater tests.CITATION:Wang, Y M, Liu, W Z, Zhang, X L and Li, L F, 2015. Application of lateral crater test in open pit blasting parameters optimisation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 463–468 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S Bhandari

This paper is a step in the direction of developing a computer model of the near source dispersal of suspended particulate matter (SPM) in planetary boundary layer (PBL). Since Surface Mine blasting is done during daytime, study of daytime dispersion in convective boundary layer (CBL) is relevant to the mining engineers. The scope of this paper covers dispersal after the blast in any type of PBL ie stable, convective and neutral but only under weak wind condition. Mathematical analysis of the dispersion of vertical dust column has been carried out during weak wind conditions in a tropical meteorological environment. It is noted that dust concentration reaches its maximum value some distance away from the point of blast, immediately after the blast (t*=1) and thereafter rapidly decreases. After a short interval from the time of blast at t*=11 the dust concentration shows linear decrease in concentration with distance. Dust concentration also rapidly drops during the interval t*=1 to t*=11, thereafter, rate of drop is nearly the same at any distance from the point of blast.

Jan 1, 2001

Most compact bucket wheel excavators in use are in the small to medium range. Large compact bucket wheel excavators compete directly with con- ventional longer boom excavators which have operational advantages over the large compact. There are, however, situations where the large com- pact excavator is viable. In the development of these large compacts there are a number of technical features to be addressed. In addition the SECV now propose to expand the concept to a large compact bucket wheel excavator with a bridge and loading unit for their Loy Yang Open Cut.

Jan 1, 1989

By Z-Y Pi, B Zhang, S Wen

"The paper introduces the structure and work processes of outside auger hollow claw tipped mechanical sampler for coal. Twenty sets of claw tipped sampler performance tests show that: The design of inner hollow cylinder-type (?180 mm) can ensure to take a coal sample with nominal top size of 60 mm. Built-in self-cleaning piston pusher ensures no adherence and blocking of the sample. The operation practices show that the mechanical sampler can operate in order for taking coal sample with up to 16 per cent of total moisture. Claw closing design can avoid sample leaking or spilling during the claw lifting and ensure the integrity of primary increment. Ultrasonic positioning device makes the sampler capture the materials no less than 10 cm from the bottom of the wagons, basically meeting the requirement taking full depth of the sample. The precision and bias test indicates that the moisture and ash have no relative bias under the sampling process; the sampling precision is in accordance with the requirement in IS013909.At present, the spiral mechanical sampler is widely used for coal sampling but there are many limitations during application, for example: It is difficult to capture a large size sample, so the size range of a coal sample taken is limited. There is easy adhering or blocking for high moisture coal, which will result in the mixture of different increments, wear of sampler and the difficulties for cleaning and maintenance of sampler. It is difficult to capture the coal sample at lower than 30 cm from the bottom of the wagons, in order to avoid damage of the vehicle. It is possible for coal sample loss and spilling during the sampler lifting, due to the unsealed sampler.For the outside auger hollow claw tipped mechanical sampler designed for solving the above problems, the opening distance of the claw is the opening size of the sampler and makes the size range of the coal sample to be taken wide. During sampling, the two pieces of claws open and the sampler rotates vertically downward to capture an adequate coal sample after reaching the specific point. Then the two pieces of claws close tight automatically to ensure there is no coal leaking or spilling. The inner pusher of the sampler will prevent from the adherence and blocking of the coal sample effectively.CITATION:Zhang, B, Pi, Z-Y and Wen, S, 2012. Outside auger hollow claw tipped mechanical sampler for coal, in Proceedings Sampling 2012, pp 41-44 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By M Hopkins, A Mutale, A E. Vidal da Silva

The Cliffs Nickel Mine extracts a narrow near vertical nickel vein using a mining method of underhand bench stoping with paste backfill. In 2014, at a depth of 400 m below surface, the Northern block of the mine began to experience squeezing within ore development. At first the deformation was localised, within 30 m of the stoping front, but later became pervasive extending across the Northern block and resulting in a hiatus in mine production. The global mechanism is a progressive pillar failure, where the inter-level pillars in advance of the production front could no longer withstand the induced load and progressively yielded. The local mechanism of failure was observed as crushing of the massive sulphide ore and ‘punching’ of the pillars into the ultramafic hangingwall exhibited as floor and sidewall dilation and unravelling of the mafic footwall. The cause of the global mechanism was attributed to a combination of factors, including: high overall extraction ratio, small vertical pillar heights between ore development, high stress in relation to the low rock mass strength, shallow stope front angle, and insufficient ground support capacity. Following the progressive failure, the remnant rock mass conditions across the northern block were severely degraded, with numerous falls of ground that led to a reassessment of the mine plan. Recovery of the Northern block started in 2016 as a staged process. Development of the safe recovery work methodology involved a number of considerations, such as: production sequencing, development access design, ground support, and development of specific procedural controls. The Northern block was then broken into smaller mining precincts based on tactical factors such as location, ease of access, scale of rock mass damage and nickel content. A specific ground support standard and work methodology are employed, while cycle sheets are used to ensure quality and completeness of work. Large intersections showing signs of deformation have either been bypassed or treated using Rocprops to maintain stability during stope production. This approach has been successful in safely regaining access and restarting production in areas that had previously been removed from the mining reserve.

Mar 15, 2021

By G Booth

Whilst communications systems in the mining industry have evolved over the years, the premise remains consistent that reliable communication is vital for safety and operational efficiency. TodayÆs open pit mines are benefiting from advanced developmental efforts based on mesh networking hardware and software technology. This paper highlights Rajant CorporationÆs adaptation of technology, originally developed for the defence and first responder industries, to provide wireless network connectivity in open pit mining applications. Featured is the large-scale deployment of over 300 mobile, meshing access points in the Bingham Canyon Copper mine near Salt Lake City, Utah, the worldÆs largest open pit copper mine. Many companies have positioned themselves, their technology and their product line in the arena of rugged outdoor wireless broadband mesh networking infrastructure. However, Rajant Corporation has combined specialised command and control software and portable networks which offer network extensibility and redundancy that are not available in any other networking solution. Rajant CorporationÆs BreadCrumb« offers unique traits in portability and non-line-of-site networking nodes which intelligently route and broadcast in standard 802.11 protocol. The advantage of RajantÆs solution is especially valuable for users needing equipment moved easily and rapidly into and out of the theatre of operations with uninterrupted network availability. The main differentiators that set the BreadCrumb« network apart from the competitors are mobility (continuous availability), simplicity, ability to properly load balance and power options. In 2007, RajantÆs BreadCrumb« wireless mesh system was selected by the Kennecott Utah Copper Corporation (KUCC), a wholly owned subsidiary of Rio Tinto, as its primary communications platform for operations within the Bingham Canyon Copper mine, the worldÆs largest open pit copper mine. The Rajant BreadCrumb« technology enables KUCC to gain additional operational efficiencies by tracking, monitoring and managing its copper mining operations. The primary goal of using the BreadCrumb« wireless mesh system Kennecott was to streamline its complex mining operations. KUCC required a high number of moving wireless nodes for improving mine monitoring and control. The Rajant InstaMesh« software running on the wireless BreadCrumb« units connects hundreds of devices to each other while rapidly transporting critical operational data. Kennecott has successfully implemented a large number of BreadCrumb« radios in an interconnected network that allows loader trucks, shovels, pumps, laptops and other production equipment to communicate with each other in real-time. These systems are a mix of secure access nodes that enable data and voice communications across a meshed, self-healing network for fleet dispatch, health monitoring and other critical mining applications. Many of the devices that require wireless communications are moving at all times throughout the wireless mining infrastructure. The BreadCrumb« nodes rapidly adapt to any changes in the network topology, assuring that IP traffic uptime and bandwidth are maximised. The installation layout and data network specifics, as well as maps and data network efficiencies will be detailed in the paper.

Jan 1, 2008

By Q Yu, G Ren, Z-Y Chen, J Yang

The wedge shape theory of the rock fragmentation range in bench blasting is presented according to the dynamic characteristics of rock fragmentation by blasting in open pit under the condition of hole-by-hole initiation. The finite element software ABAQUS was used to analyse the rock fragmentation mechanism. The rock mass stress contours, crack propagation and damage evolution of different moments were obtained. The results showed that the wedge shape theory of blasting is closer to the rock fragmentation in hole-by-hole blasting and is useful to the design and calculation of charge weight.CITATION:Yang, J, Chen, Z-Y, Yu, Q and Ren, G, 2015. The wedge theory of borehole charge design for bench blasting and its numerical simulation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 169–176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M Nagarajan

Orica Mining Services (Orica) in partnership with Coal and Allied’s Hunter Valley Operations (HVO) has developed a risk management process to maximise mining efficiency whilst controlling vibration and maintaining critical electricity continuity to New South Wales (NSW) electricity grid in the Riverview Pit. The issue is a high tension tower which supplies electricity located within 40 m of mining and blasting activities. The process involved developing an understanding of the relationship between vibration, explosives, geology and the location of the blasting in the geological horizon. From this an optimum methodology for blasting in each region was developed.

Nov 8, 2011

By S C. Dominy

Gravity amenable gold ores are those that after comminution produce liberated particles, composites and/or carriers that can be recovered by gravity separation means. Recovery depends upon mineralisation type and the comminution and concentration method used. Any in situ ore with more than 20 per cent of gold greater than 100 µm in size is likely to have a strong gravity recoverable component. A less traditional approach is where the gold is sulfide-locked and the gold carrier plus any liberated gold is recovered via continuous gravity recovery following fine crushing. Specific tests are undertaken to determine the level of gravity amenable gold within a deposit. The principal methodology is the gravity recoverable gold (GRG) test, which consists of three sequential liberation and recovery stages. For continuous gravity recovery (CGR), the sample is fed over a laboratory Wilfley table to simulate continuous recovery of the gold. Tails from the feed can be progressively re-ground and re-tabled to develop a grade-recovery curve. Primary geology and gold particle size-distribution have a strong effect on the mass of sample required to provide representative results for both tests. Where low-grade ore contains very coarse gold, substantially larger sample masses are required. Experience has shown that GRG and CGR values can vary throughout an orebody, particularly within different geological-grade domains. A testing regime must consider sample frequency and support.

Sep 5, 2011

By J Player, R de Vries, J F. Carswell, R Hassell

"The feasibility of Dugald River mine was highly sensitive to mining and geotechnical design assumptions, particularly stope dilution and strike length. Following the start of initial mine development in 2012 the project was suspended in 2013 due to concerns over the complex ground conditions and resulting dilution, stope sizes and general mineability. A technical risk mitigation program was undertaken with a key aim to increase the level of confidence in predicting stope dilution.A stope sizing and dilution model was developed that provided a range of stope sizes based on geotechnical conditions and acceptable dilution. The original feasibility used a standard stope size of 25 m height by 25 m span. The new model was used as the foundation for the subsequent updated development plan for Dugald River that reduced much of the previous technical risk through greater confidence in the geotechnical and mining parameters.Several methods to predict stope hanging wall dilution and appropriate stope size have been used at Dugald River that relied on the modified stability graph method. Improvements to the method were identified as more rock mass and mining data became available through the completion of a trial stoping program, increased underground development and a large geotechnical core logging campaign. These improvements not only focused on the technical aspects of the model, but also on creating an easy to use and sustainable process that could be used at multiple stages of mine planning from life-of-mine (LOM) through to final stope design.Several of the main improvements are: understanding stope failure mechanisms and collecting only geological information that is most relevant detailed modelling restricted to the rock mass that could be expected to influence stope behaviour accounting for different stope failure mechanisms with the stability chart method assigning a geotechnical confidence factor to the data making it useful as a mine planning tool with integration into the mine planning process using performance of completed stopes to update and calibrate the model.The model provides recommended hydraulic radius and associated dilution estimates across the ore body. Providing the hydraulic radius allows planning engineers the option to consider single, double and triple lift stoping options suitable to mine scheduling. While the model has been calibrated for conditions at Dugald River the process used to create the model is not site specific and is applicable to other steeply dipping tabular orebodies.CITATION:Hassell, R, de Vries, R, Player, J and Carswell, J F, 2017. Improving the prediction of stope hanging wall dilution – a critical factor to the success of Dugald River, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 71–78 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017

By Whiten WJ

Although cone classifiers have received little attention in the modelling of mineral processing units they are one of the oldest non-mechanical classifiers. Their use has enjoyed a revival in recent years because of their low cost of installation and operation. In this paper the development of models for cone classifiers is reviewed and a new model is proposed. The experimental work, data collection and analysis are briefly described, and the new model is presented and discussed. The data used in the model development are made up from three distinct experiments using different units in each case. There are 21 data sets from a 3 m cone treating the tailings in a copper concentrator, 24 data sets from a 0.3 m pilot-scale cone, and 29 data sets from a laboratory glass funnel (0.(Y73 m diameter) used as a cone classifier, giving a total of 74 data sets. The model structure was developed from an analysis of particle settling in classifiers, using specialised model building software. The size of a particle settling in a separator and the forced flow through the apex of the cone were related via hydrodynamic dimensionless groups to the operating conditions of the unit. The model predicts the separation efficiency using the following four parameters: efficiency curve shape factor, cut-point, underflow density (per cent solids) or underflow pulp velocity. The model covers a range of feed flowrates from 1.2 to 5000 1/min.

Jan 1, 1993

By S Mitra, D O’Dea, N Barrett, T Honeyands, P Zulli

The steel industry continues to explore and demonstrate technologies that decrease its greenhouse gas emissions, especially in blast furnace ironmaking where alternate operating conditions will be required. As the furnace has been optimised over many years, it is approaching the minimum fuel rate possible with coke and Pulverised Coal Injection (PCI). Alternative operating conditions are therefore required to further decrease greenhouse gas emissions. Because of this, hydrogen has been proposed as a reducing agent in the blast furnace. Injection of hydrogen through the tuyeres was assessed using a comprehensive 2D blast furnace global model. The model was calibrated to a blast furnace operating with PCI as a base case and various approaches to hydrogen injection assessed, with a particular focus on displacing PCI. The maximum hydrogen injection rate of 19.5 kg H2 per tonne of hot metal was predicted, limited by decreases in the raceway adiabatic flame temperature and top gas temperature. Internal blast furnace conditions, such as gas composition and reduction degree were also predicted. Holistic analysis was performed to estimate the effectiveness of hydrogen injection on reduction of greenhouse gas emissions. Based on these results, the changes in blast furnace operation and emissions under hydrogen injection are discussed.

Nov 8, 2021

By M Fritz, B Ziegelaar

"For moisture samples, the International Standard for iron ore sampling states the following: Moisture samples shall be processed as soon as possible and test portions weighed immediately. If this is not possible, samples shall be stored in non-absorbent airtight containers with a minimum of free air space to minimise any change in moisture content, but should be prepared without delay. ISO 3082 (2009)Prescribing what to do is of course easy. Putting it in practice is, however, a little more problematic.The iron ore industry has seen quite some changes in the last ten to 15 years, such as: a large increase in the volume of seaborne trade new ore types and blends coming onto the market new mines, processing plants and port facilities producing more and loading faster an increase in wet processed ore products a dramatic rise and then equally dramatic fall in the iron ore price followed by a recent recovery.All of the above have had an effect on sampling facilities. The large increase in volume coupled with ambitions such as labour efficiency, safer operations and higher precision has driven the installation and retrofitting of automated sampling and robotic sampling preparation plants in order to keep up with increased quality control.Designers of sampling facilities are invariably instructed to build plants that comply with ISO 3082. In general this means that the plants are compliant in respect of the number of primary increments, gross sample masses and sample division rules. The clause at the beginning of this abstract is mostly overlooked as it only appears in a section (4.1) describing the basic requirements of a sampling system.An error of 0.1 per cent in moisture changes the value of 1 Mt of iron ore at US$50/t by US$50 000. At 700 Mt/a of Australian iron ore exports, this is US$35 M. Frequently, errors from 0.5 to 1 per cent in moisture measurements are encountered.In comparison an error of 0.1 per cent Fe is US$0.081 (US$50/t and 62 per cent Fe base) per tonne, that is US$81 000 per Mt or about US$51 M for the same Australian annual iron ore exports.It is somewhat mystifying that we in the ISO Technical committees spend extraordinary energy (= money and time) on improving measurement techniques, whilst the big costs are in sampling errors. This is particularly true for moisture measurement. Our paper quantifies some of the sources of moisture measurements errors and suggests mitigating actions.CITATION:Ziegelaar, B and Fritz, M, 2017. Sampling for the percentage moisture in the iron ore industry, in Proceedings Eighth World Conference on Sampling and Blending, pp 271–274 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 9, 2017