Search Documents

By Marshall GA, Dickerson AW

The efficient operation of large haul trucks in large open pit mines requires an economic trade off between the haul route quality, the haul truck payloads and the level of haul truck reliability. This paper describes an investigation into the relation- ship between haul route surface quality and the level of structural reliability of a haul truck main frame. An instrumentation system for unattended recording of data on a haul truck operating normally in a mine and com- puter based analytical procedures were developed and used to identify which road segments contribute significantly to fatigue cracking at various sections of a haul truck main frame. INTRODUCTION In many open pit mines there is exten- sive use of large haul trucks to move over- burden and minerals. In most open pit hard rock mines, both the overburden and mineral ore are moved by large rear dump type haul trucks. Similar haul trucks are also widely used for coal overburden and mine site coal haulage operations in New South Wales, South Australia and Western Australia. Large bottom

Jan 1, 1982

By M A. Llano-Serna, D J. Williams, L Bu

Tailings dam failures continue to occur worldwide at an unacceptable rate, averaging two events annually over the last 100 years. Furthermore, tailings dams continue to grow in size, increasing the potential release of tailings and water should they fail. Tailings are generally deposited in a slurry state, with the potential to flow if containment is lost. Understanding the generation and propagation of excess pore water pressure on failure is critical to predicting the flow and run-out of tailings. This paper presents numerical modelling using the material point method indicating that tailings run-out processes may be self-enhanced by the excess pore water pressure induced during the collapse of the containment. Moreover, it is shown that geomorphological features, such as the slope and its surface roughness downstream of the tailings dam, influence the pore water pressure dynamics upstream of the advancing toe.CITATION:Llano-Serna, M A, Bu, L and Williams, D J, 2018. Excess pore water pressure induced during tailings run-out, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 377–383 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By M W. A Asad, E Topal, D S. S Sandanayake

Underground mine planning requires an optimal stope layout as a prerequisite for the definition of an optimal production schedule. The procedure to generate an optimal stope layout considers an orebody model and economic parameters as inputs. It evaluates all possible combinations of mining blocks and creates a set of stopes by satisfying the physical mining and geotechnical constraints. Thus, the procedure is computationally complex, and generating a solution to the problem is a challenge. This paper presents an implementation of a new heuristic algorithm that solves the stope layout problem. In two case studies, the algorithm achieves 11.2 per cent and 22.5 per cent superior solutions to the industrially available maximum value neighbourhood approach.CITATION:Sandanayake, D S S, Topal, E and Asad, M W A, 2014. Implementing a new heuristic approach to the underground mine stope layout problem, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 243–248 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By K J. Lownie, T Rafferty

The in situ testing of mine ventilation fan systems has been a contentious issue for many years. Site testing was generally undertaken by adapting standards that were developed for the laboratory testing of fans using standardised airways. The deficiencies inherent in this practice have been widely recognised by informed practitioners, and this led to the first stand-alone document specifically intended for the in situ testing of large fans (ISO 5802:2001 Industrial fans - Performance testing in situ).This paper describes the structure of the International Standards organisation and the processes that are followed in the course of preparing such a standard.The application of ISO 5802:2001 is briefly outlined together with how test data is assessed for compliance with the suppliers guarantee. This paper must be read in conjunction with ISO 5801:2007, ISO 5802:2001 and ISO 13348:2007.CITATION:Lownie, K J and Rafferty, T, 2013. A review of ISO 5802:2001 industrial fans - performance testing i n situ, in Proceedings The Australian Mine Ventilation Conference , pp 149-154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By L Bertoss, D Carvalho

In the last decade, the use of advanced implicit modelling software/algorithms in mineral resource workflows has become a best practice in the mining industry. In most cases, these workflows can easily replicate the level of detail of explicitly modelled geometries, even for very complex deposits. These techniques are flexible and can produce fast results since software is responsible for generating 3D surfaces and solids based on geological and interpretation data. Nevertheless, depending on how unique and complex some deposits are, intense manual editing and input are required to honour the geological context and produce the desired outcome. The current geological modelling workflow at George Fisher Mine (GFM) is based on the semi-automatic built-in tool that generates stratigraphic sequences (stacked lithology layers) based on logging and mapping data. This tool (stratigraphic sequence from Leapfrog Geo™) works for the majority of areas in the mine but fails to capture observed mineralisation pinch-outs in operational areas and at extrapolated boundaries of the deposit. These pinch-outs have the potential to negatively impact grade forecasts if not resolved manually. Using built-in software tools only, the alternative for a more accurate model is to generate each individual layer and adding tens of thousands of manual interpretation points to honour pinch-outs (based on the amount of existing drilling in the mine and number of layers). This approach would require an estimated minimum of two to four years of a full-time employee (FTE) to be exhaustively completed. This study presents an automated approach to generate pinch-out points using a set of Python scripts that only take a few minutes to run. The newly generated points are then combined into the commercial software workflow as interpretation points, honouring observed pinch-outs. The remarkable time difference between approaches removes chance of manual errors and allows mine geologists to spend valuable time in validation and testing of scenarios, ensuring they are more representative of the deposit’s geology.

May 24, 2023

By R Grobler, D Burger, L Alberts

The current climate in the mining industry is allowing mining companies to further broaden their views and investigate technologies to improve the safety, efficiency and cost-effectiveness of their operations. Furthermore, underground mine environments will become more demanding for mining equipment and personnel as orebodies become deeper in weaker ground conditions with more extreme environmental conditions. Loading and hauling can represent significant components of the production cycle of an underground mine and automation of these activities can offer considerable benefits. Sandvik has accumulated a long history and experience in loading and hauling automation in underground mining. Since the late 1980s Sandvik has actively participated in several major research and development automation programs leading to the commencement of the development of an integrated system for semiautomated loading in 1999. Development work was later conducted to expand the capabilities of the system for automated hauling during 2001 and the AutoMine« system became commercially available. The first delivery of the AutoMine« system was completed in August 2004 in South America, where the system continues to operate in a full-scale production environment and is being expanded as the production area enlarges. Further systems have been delivered and are operational in North America, Africa and Europe. This paper focuses on the AutoMine« system deployed in Block 4 at De Beers Finsch Mine in South Africa. An overview of the mine and the process used to acquire the system and the key drivers which led to the selection of an automated solution are described. An overview of the initial system installation, subsequent expansions and future plans are presented. This is followed by a summary of the implementation and operational experiences associated with automated underground operations. The paper concludes by summarising the benefits that have been realised.

Jan 1, 2008

By D Corley, J Moore, M Grant, A, W R

Resource estimates are the corner stone of technical and investment decision-making. Prior to mining, resource estimation uncertainty has the greatest potential to lead to poor investment decisions, despite a significant component of resource estimation uncertainty being unknowable at this critical stage in the mining cycle. This presents a conundrum to the resource geologist in terms of risk evaluation and resource classification. Ahead of mining, there is normally considerable focus on drill hole spacing analysis to determine the ‘optimal’ drill hole spacing, taking grade and geological continuity into account; cost-benefit analyses balance improved resource definition against cost; the law of diminishing returns and the exponential cost increases acting together as spacing is reduced. Typically, a lower limit to the drill hole spacing is identified. After completing the resource drilling to an agreed spacing, resource estimation is then undertaken. At this point it is common to attempt to bracket the resource estimation uncertainty. In many cases conditional simulation is used, based on a modelled, but largely assumed, variogram model. It is also assumed that the histogram of the available drill hole sample data is representative of the in-ground mineralisation. The purpose of this paper is not to diminish the importance of drill hole spacing and simulation studies, but rather to illuminate an important aspect of estimation uncertainty that, although previously recognised, is typically overlooked – the question of how representative the available data set is in characterising the true (but unknown) distribution of mineralisation. To do this, we lift the lid on one of OceanaGold’s former operations, the mined-out Globe Progress Mine, by resurrecting a high quality, close-spaced, reverse circulation (RC) grade control data set. The Globe Progress Mine is within the West Coast Region of New Zealand, it was closed and transitioned to rehabilitation in 2016 and is now known as the Reefton Restoration Project. The exhaustive Globe Progress grade control data was used to repeatedly ‘redrill’ the deposit by extracting 35 m × 35 m spaced subsets from the original 5 m × 5 m spaced grade control data. Utilising closely spaced grade control data removed the need for assumptions regarding short range continuity, which are necessary with forward-looking analyses that are based upon broader spaced resource drilling. The extraction process used a nearest neighbourhood algorithm, repeatedly moving the origin in 5 mE, or 5 mN increments. Individual resource estimates were then completed for each of the extracted drill hole data sets (49 in total) as well as a grade control estimate based upon the exhaustive data set. Whilst the data unpinning each of the 49 estimates changed, the geological assumptions, variography, and modelling parameters remained constant. This approach was taken to isolate the impact of changing the input data. The 49 estimates were then compared against each other and the grade control estimate. The mean of all 49 sensitivity estimates was close to that of the grade control estimate in terms of contained gold, tonnes and grade. Whilst it is acknowledged that the grade control estimate itself is subject to some degree of estimation uncertainty, the close match between the average of the 49 estimates and the grade control estimate suggests that the resource estimation methodology is reasonable and appropriate. Whilst this comparison is important, the focus of this study is on the component of estimation uncertainty related to the underlying data, and this is reflected in the spread across the estimates. The spread across the 49 global estimates (highest to lowest) for this particular Mineral Resource Estimation Conference 2023 | Perth, Australia | 24–25 May 2023 142 case study was found to be significant (approximately 20 per cent in grade and metal) and that is attributable solely to the underlying data. This exercise quantifies a component of the estimation uncertainty that is inherent to all drill hole data and is distinct from the uncertainties associated with modelling methodology choices, sample and subsample quality and drill hole spacing-related interpolation uncertainty. Importantly, this uncertainty is unknowable prior to mining; we can only directly compare the resource drill hole data against grade control data after mining has taken place. For the case study, approximately 65 per cent of the estimates fell within 5 per cent of the grade control estimate for contained-gold, suggesting that for many projects the histogram of drill hole data is unlikely to differ noticeably from that of the in-ground resource. However, about 15 per cent of the estimates in this study differed by more than 7.5 per cent, suggesting that a not-insignificant proportion of estimates will be materially compromised. Whether or not the available drill hole data is representative comes down to the ‘luck of the draw’ and cannot be known at the time of resource estimation. Given the challenge of attempting to evaluate forward-looking estimation uncertainty, a component of which that can only be quantified retrospectively, what should we do as resource geologists? What are the implications for risk evaluation, resource classification and reconciliation? Furthermore, without rigorous post-mining data checks, resource geologists may conflate suboptimal modelling with the shortcomings of the underlying data. An example of this problem is discussed in the following section.

May 24, 2023

By R Hargreaves, T Elkington, W J. Shaw, G W. Booth

Every day, around the world, thousands of tons of ore are loaded onto ships completing the miningproduction process and starting a multimillion-dollar economic transactions process. These transactions are based on the supply of tons of a commodity with certain specifications of assays of the main element (or physical properties) and concentration of contaminants, which are finally verified and evaluated by buyers, and also are considered ‘as true’ during Reconciliation process. On Sample Stations, this ‘true’ is based on a few kilograms of sample, often representing thousands of tons, that are sent to laboratories for further sample preparation and chemical analysis, where finally assay information is obtained from a few grams of pulverised sample, and are used for further production, planning, operational and financial-marketing decisions. Different International Standards (depending on the commodity) are used to establish the methodology to be followed, to set-up and obtain samples from the Sample Stations, and the specifications are visually inspected to give an estimation on the performance of the sampling point. This paper seeks to highlight with examples, the importance of the implementation of a continuously monitored Quality Program (QAQC and QM) on Sample Stations, focused on the parameters that directly affect the quality and representativeness of the samples. By this implementation, a proactive approach and better-informed decisions can be taken for mining companies to: a) quantify/improve production and reconciliation results, and b) to supply the right specifications of shipped ore, increasing the value of the Resources. Finally, laboratory results are normally used as an indication of the quality of the information applied for the economic transaction, but it should be considered, clarified and highlighted that the laboratory will only process and analyse a sample obtained from a Sample Station, and potential problems on bias or precision may occur in stages prior to the laboratory reception. Hence the importance of the implementation of a quality assurance program that protects multi-million dollar decisions.

Mar 22, 2022

By J Coveney, A Rich, D Grimsey, J Wood, S Creedy

In 2021, BHP and Metso examined processing of high-MgO nickel sulfide concentrates using Metso’s Ausmelt Top-Submerged-Lance (TSL) technology. Test work was conducted in Metso’s pilot test work facility in Dandenong, Australia to explore operability of the SiO2-FeO-MgO-CaO-NiO slag system across a wide range of compositions, temperatures and bath oxygen potentials. Pilot-scale testing aimed to define slag ‘operability limits’, representing the lowest bath temperature at which stable process and equipment operation could be maintained. This work was supported by FactSage™, version 8.2 (by Thermfact/CRCT and GTT-Technologies) thermodynamic modelling, slag viscosity measurements, physical characterisation of quenched slag samples performed by the University of Queensland and benchmarking of commercial-scale TSL nickel smelting operations. A wide range of slag compositions were examined, with Fe/SiO2 ratios varying from 0.4–1.1, CaO content from 0.8–7.0 wt per cent and MgO content from 6–19 wt per cent. Slag SiO2/MgO ratio, wt per cent CaO and matte grade were found to have the greatest impacts on identified operability limits. Operability limits were found to be influenced by both the solids content in slag and viscosity of the remaining liquid slag phase, with the relative contribution of these parameters heavily influenced by the slag composition. In the majority of trials, limits were defined by a theoretical solids content of 40–50 per cent, however in trials with a low Fe/SiO2 ratio and/or low wt per cent CaO, limits were characterised by a much lower solids content due to the increased effect of the liquid slag viscosity in determining the behaviour of these slags. The test work highlighted inherent flexibility of the Ausmelt TSL process to operate across a wide slag range of slag compositions and recover from process disturbances without an interruption to feeding. The trials also demonstrated the possibility for Ausmelt TSL technology to process concentrates with an Fe/MgO ratio as low as 1.4, which has important implications to the commercial-scale processing of high MgO feeds. Arsenic rejection across the trials was very good, with only 30 per cent of arsenic in the feed inputs reporting to the matte phase. Such high levels of arsenic removal provide the Ausmelt TSL process with a notable advantage over alternative smelting technologies.

Aug 21, 2024

By D J. Kilkenny, D A. O’Toole, P B. Hills, K L. Seah

An investigation was undertaken to critically analyse the use of fibre reinforced shotcrete (FRS) for a variety of applications in large diameter shafts. Those applications included the use of FRS with or without the addition of subsequent rock bolting in the temporary support cycle prior to the installation of a permanent lining, most likely cast in situ concrete or as the final lining medium.Numerous authors have considered the early re-entry and strength characteristics of FRS in recent years. The current study has investigated the practical application of the recommendations of many leading authors in an endeavour to establish practical and acceptable risk-assessed procedures for the use of FRS for rapid, safe, efficient and cost-effective shaft sinking.Shaft sinking is regarded as a specialist and potentially higher risk activity due to the confined work environment, exposure to ground conditions and a high degree of manual handling associated with getting materials to the sinking face. The use of robotically applied FRS as a primary lining in shaft sinking has significant safety advantages in reducing manual handing associated with mesh safety support and bolting, as well as reducing direct exposure to ground conditions.The study involved both field testing and a literature review. The study established an initial set of criteria for the use of FRS in the development of large diameter shafts and demonstrated a number of scenarios where the technique of robotically applied FRS provided significant safety and cycle time advantages. The opportunity for a fully sprayed single pass lining was also investigated as part of the project.CITATION:Hills, P B, O’Toole, D A, Kilkenny, D J and Seah, K L, 2014. Exploring the use of fibre reinforced shotcrete in large diameter shafts, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 295–306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By K J. Riihioja, E Nozawa

SmartTag is a radio frequency identification (RFID) based technology designed to allow tracking of ore from its source through blasting, run-of-mine (ROM) pads, crushers, intermediate stockpiles and finally into the concentrator. This paper presents current developments and the future direction of the SmartTagÖ ore tracking system, as well as presenting some case studies. Successful applications of the SmartTag system have encouraged development to allow the system to be used in a wider variety of plants, in particular plants with finer crushing and screening stages. This presented Metso with a number of technological challenges, including RFID tag and antenna design. By reducing the traditional RFID tag diameter from 60 mm to 20 mm the RFID tags can now successfully pass through a secondary crusher. The new smaller RFID tags (referred to as mini RFID tags) have been used in some Process Integration and Optimisation projects with very promising results. The results indicate that the miniature RFID tags have a higher survivability to blasting and through secondary crushing stages. Extending ore tracking further through the process allows more reliable linking of spatial data with time based process performance. Metso is looking at developing even smaller micro RFID tags, and is also investigating other applications for the SmartTag system, including ore tracking from the original source to the final destination (ie from the mine, through the plant and ports to the customer).

Sep 26, 2011

By T Roesch, M Neurohr, S Stratton

"Dwindling commodity prices are forcing today’s mining operations to increase output. Sometimes the solution is to upgrade the existing infrastructure; however, in most cases it has to be achieved with the same or reduced workforce and with the same equipment capacity through improved process efficiency and higher uptime.Measure, Manage and Improveis the mantra for this years’ Mill Operators’ Conference and while this in most cases relates to the above process efficiency, Siemens has set its focus on the availability and uptime aspect since unscheduled downtime is one of the biggest threats to any grinding operation. Pinion misalignments, resonance, unbalance and bearing and gear meshing faults in geared trains, as well as long-term changes in the condition of the mechanical components or structures and auxiliary systems in gearless systems are the main reasons for unscheduled downtimes in today’s mill drive trains. Our paper outlines the efforts that have gone into adapting conventional condition monitoring methods in conventional, pinion driven mill drive trains as well as gearless systems to capture the gradual deterioration of wearing parts or structural changes in the drive train not only on fixed speed application but also on variable speed applications with multiple operating points. The paper further explores the use of condition monitoring systems as a tool to assess spare thermal motor capacity to potentially push equipment beyond its nameplate rating, along with the process that was followed to correlate measured frequency spectra and envelopes to ambient and load data to understand the kinematics of the drive train.Citation:Neurohr, M, Stratton, S and Roesch, T, 2016. Advancements in Condition Monitoring on Mill Drive Trains for Proactive Maintenance and Early Fault Detection Purposes, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 263–272 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

It is well known that the ability to influence project value reduces significantly as planning progresses and decisions regarding project parameters are made. However, at the prefeasibility stage in particular, where one of the main aims should be to evaluate a wide range of options in order to select the best for more detailed further study, there is often a reluctance to spend the time and money needed to do this rigorously. This paper demonstrates, by a number of case study examples, how significant increases in value may be obtained by fully evaluating the combinations of alternatives for various project design parameters, including (though not limited to) mining methods, haulage methods, mining rates, processing methods and rates, sequencing of mining, and cut-off grades, with changes and upgrades over time where applicable. The additional value unlocked is typically orders of magnitude greater than the additional cost of the more comprehensive study. The dangers of misuse of simplistic sensitivity analyses and failure to identify how strategies might change in response to changes in external factors are also illustrated, and the importance of selecting the best ægrade descriptorÆ is discussed.

Jan 1, 2007

By J Rose, D O’Toole, D Grant

Orepasses are a critical element in the transport of ore from the stope drawpoint to the surface ore stockpile, making them an integral part of an underground mine’s ore-handling system. Well-designed and operated orepasses improve productivity and lower operating costs over a long period of time.The Olympic Dam mine, as part of a 6 Mt/a expansion project in 1997, constructed a large network of orepasses feeding a rail haulage system to facilitate the movement of approximately 8 Mt/a to the Clark crusher and hoisting shaft. The orepass network comprises 14 orepasses and currently includes 59 individual tip points. The orepass network has been in operation for over 15 years and in excess of 110 Mt of ore has been moved through the system.Olympic Dam’s management of mine infrastructure includes a program of assessing the condition of the Clark system orepasses. A comprehensive program was initiated in 2011 and consisted of systemically performing volumetric surveys to determine the integrity of the various sections of the orepasses. The current geometrical state of the orepasses provides essential information for comparison of geotechnical and operational parameters and a baseline for understanding the key causes of orepass deterioration to assist in the planning of both usage and potential replacement options.The collection of geotechnical and operating data allowed the review of the current condition, potential longevity and associated risks with the various orepass sections. Initial studies have also reviewed options for rehabilitation and/or replacement.CITATION:Rose, J, Grant, D and O’Toole, D, 2016. Orepass monitoring and management at Olympic Dam Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 609–616 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By S A. Ravishankar

In heavy minerals separation, the titanium and iron oxide phases are separated from silicates in the coarser particle size range (80 - 150 mm) using magnetic and electrostatic separators. With the ongoing challenge of heavy mineral ore deposits getting increasingly finer in particle size, conventional separation equipment suffers from the ability to process this material at the same throughput rate as coarser particles. A variety of magnetic separation technologies were developed to perform at a much finer particle size range, down to 2 mm in the clay industries mainly to remove titaniferrous oxide particles. Complementing the developments made on the physical aspects of magnetic separation, Cytec Industries has recently developed a ‘bolt-on’ chemical enhancement technology for magnetic separation (CEMS). This is to enable separation of finer particles, and weakly paramagnetic titanium phases from diamagnetic silicates that are not amenable to magnetic separation. This paper will provide an outline of the technology, illustrate its ability to process a wide variety of ores, and also discuss plant limitations. The major advantages of chemical enhancement technology to magnetic separation includes: simple dosing equipment extension to existing magnetic separation technology; ability to produce product of comparable quality with improved cost effectiveness, when compared to incumbent flotation; removal of impurity minerals over wider size range; enhanced removal of non-magnetic impurities; and improving the process robustness. Furthermore, chemical enhancement technology for magnetic separation has also emerged as a platform for removing impurities at lower levels in other mineral systems as well.

Oct 5, 2011

By J W. Glatthaar, M Mavotoi

The occurrence of fluorine in the copper/gold concentrates produced by Ok Tedi Mining Limited has provided a series of challenges to metallurgists since 1988. Although fluorine is distributed throughout the gangue minerals contained within Ok Tedi ores, itsÆ presence in talc and phlogopite (naturally floating fluorosilicates) has proven to be the predominate sources of fluorine in the final concentrate. Initial treatment for the fluorosilicates consisted of the use of a carboxy-methyl cellulose depressant added to the flotation cleaners. This was superceded in 1998 with the installation of a fluorine reverse flotation process for the removal of naturally floating fluorosilicates from the final concentrate when the fluorine content of the final concentrate exceeds smelter-defined trigger points. The fluorine reverse process is similar to by-product molybdenite concentrate production in that sodium hydrosulfide is used to depress copper/gold flotation whilst allowing the fluorosilicates to float. The process was installed in two parallel modules (to match the existing grinding/flotation modules at Ok Tedi), each consisting of a closed rougher/cleaner circuit configuration. Both rougher and cleaner cells are Jameson Cells from MIM Process Technologies, with the selection based on both processing characteristics and available construction space. This paper discusses both the nature of fluorine in-, and its removal from-, Ok Tedi copper/gold concentrates.

Jan 1, 2003

By T G. Vizcarra, T J. Napier-Munn, A T. Karbowiak, M G. Hart

Squeezing extra performance from existing equipment (‘sweating the assets’) is key to continuous improvement initiatives, particularly during times of cost cutting where the option of spending additional capital to facilitate circuit upgrades can be severely constrained. A common challenge, however, is identifying the best combination of settings for different process variables, as their effects can be camouflaged by interactions with other process variables and, of course, noise in historical data.This paper describes a recent investigation at Boyne Smelters Limited to identify strategies to coarsen the product of its dry, fixed-speed, open-circuit AG mill, without the need for installing pre-screens prior to the mill. The product is used as insulation material for the reduction of alumina to aluminium, and an excessively fine product was inhibiting the ability of the cover material to dissipate heat from the underlying anodes. The approach was to undertake a series of experiments, designed according to statistical criteria, to elucidate the effect of key process variables (feed blend and power draw) upon the product sizing. The results provided clarity about what strategies would encourage the production of a more desirable mill product (with some surprises). The study is a good example of how properly designed experiments can identify hidden potential in processing circuits, thereby mitigating the need for capital-intensive upgrades.CITATION:Vizcarra, T G, Hart, M G, Karbowiak, A T and Napier-Munn, T J, 2018. Getting the most from existing processes: using cleverly designed experiments to optimise the line 3 AG mill at Boyne Smelters Limited, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 207–216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

Most publicity about the copper industry nowa- days is focused on the adequacy of ore reserves and on excessive mining capacity. These concerns, stemming from public awareness of actual and poten- tial shortages and oversupplies, relate to production rather than consumption. Perhaps the reason for this one-sided view is that copper is thought of as a commodity which is conspicuously traded in world markets, rather than as one of many industrial materials that serve today's rapidly changing tech- nology. Copper differs from other widely traded com- modities in that its real cost of production has pro- gressively increased since World War II. The reasons for the increase are identifiable by analyzing operations in one of the world's large producing centres, the copper province of Arizona. Another respect in which copper differs from some other com- modities is that increases in demand occur less auto- matically in the case of copper than they tend to in commodities whose consumption is more directly related to population growth. The copper industry's current inability to generate and attract needed investment capital is attributable to these differences between copper and other com- modities; it suggests that the concept of copper purely as a commodity is outdated. The key to the problem is better integration between the activities of copper producers and users. Depending on cir- cumstances, integration takes various forms- for example, investment tied to long-term sales con- tracts between producers in developing countries and consumers overseas; common ownership of pro- ducing and manufacturing facilities in industrialized

Jan 1, 1978

By S Flanagan, M M. Mete, A R. Tiryaki, M Guresci

First Quantum Minerals (FQM) operates the Cayeli underground copper mine in Turkey. In response to a lost time incident (LTI) that occurred at the mine in 2022, the mine management decided to introduce a new safety approach on-site. The initiative began with a comprehensive safety culture analysis conducted by Arti Consulting, involving focus group studies. Employees actively participated in candid discussions, sharing their insights on safety issues and offering solutions. These conversations were meticulously audio recorded, resulting in over 150 000 words collected from more than 100 employees. These transcribed narratives then underwent rigorous semantic analysis, with the assistance of a sociologist, to identify and dissect patterns of unsafe behaviour. This analysis found areas for improvement, particularly in near-miss and incident reporting, quality of safety toolbox talks and effectiveness of pre-work risk assessments. Subsequently, mine management deliberated on these insights and devised corrective actions. An emphasis was placed on involving all employees in the corrective actions through communication training, empowering them to own the decisions and changes made. These impactful measures were seamlessly integrated into FQM’s Think! Safety Program, which embodies FQM’s sensible health and safety strategy. FQM partnered with Strika Entertainment (Strika) to develop innovative visual-first safety communication tools that use illustration, animation and graphic design to simplify complex messaging into easy-to-understand edutainment. As part of this approach to safety communications, Cayeli and Strika revamped the safety toolbox talks to encourage employees to voice their concerns and receive feedback when their suggestions were implemented. The response from employees has been positive, with over 200 unsafe behaviours and conditions reported within the initial two months of launching the Think! Safety Program. Remarkably, the Cayeli Mine has not experienced any LTIs for the past 500 days as of 9 December 2023. This paper encapsulates the dedicated efforts to transform Cayeli into a safer mining operation.

Apr 16, 2024

By D Cliff

"Recent underground coal mine incidents have again raised the issue of: under what circumstanceis it safe for personnel to re-enter the mine? Mine rescue guidelines make recommendations aboutthe limits in terms of the circumstances, lives at risk, no lives at risk and training exercises. Theseare based upon percentages of the upper and lower explosive limits. Many factors infl uencesett ing limits for safe re-entry. These include: the representativeness of the sampling location(s),the rapidity of gett ing an underground sample analysed and the rate of change of the atmospherebeing monitored. Value judgements based upon these parameters will then infl uence the sett ing ofa trigger point based upon per cent explosibility. This raises the question of how the percentage ofthe lower or upper explosive limit is established. It is easy to defi ne this when the sampling pointdata sit on the fresh air limit line. However - what value is used when the sample sits somewherein the body of an explosibility diagram? This paper explores the various options and illustratesvarious pitfalls and problems that are faced in making such a determination. These include howthe data are represented and the assumed knowledge of those doing the interpretation."

Jun 1, 2012