Search Documents

By K E. Mudzanani, T A. M Msagati, D T. Maiga, T T. Phadi, M R. Letsoal, B M. Chabalala, S W. Limani

This paper addresses critical environmental, health, regulatory and scientific concerns related to gold mining activities in the specific area of Barberton, Mpumalanga, South Africa. The paper thus calls for informed decisions to be made by the authorities to safeguard both the environment and people’s health. The novelty of this study is based on its comprehensive nature of the simultaneous assessment of both cyanide and potential toxic elements (PTEs) in tailings, while taking into account their composition variability over time. By combining these aspects, it is then possible to provide a holistic understanding of the contamination risks associated with mining tailings and thus justify the need for regular monitoring and supervision to ensure compliance against regulatory limits. Additionally, this paper considered investigating the dynamic nature of tailings, which are subject to changes in their chemical composition due to exposure to weathering by various agents. In this study, the determination of weak acid dissociable (WAD) and free cyanide in tailings was performed using a validated method employing the South African Council for Mineral Technology (MINTEK) Laboratory Cynoprobe. The PTEs in tailings were determined by an inductively coupled plasma optical emission spectrometer (ICP-OES). The results revealed that the tailings contained primarily substantial amounts of PTEs, including Fe (87 566 to 37 800 mg/L), Cu (271 to 110 mg/L), Mn (2100 to 680 mg/L), Ni (400 to 390 mg/L), Zn (180 to 68 mg/L), Cr (645 to 510 mg/L), As (450 to 128 mg/L), and Pb (up to 35 mg/L). The cyanide concentrations in tailings varied between 0.20 mg/L and 0.26 mg/L for free CN (with a mean of 0.23 mg/L in water leaching), 0.23 mg/L to 0.28 mg/L for free CN (with a mean of 0.25 mg/L in alkali leaching), 0.24 mg/L to 0.35 mg/L for WAD CN (with a mean of 0.28 mg/L in water leaching), and 0.31 mg/L to 0.39 mg/L for WAD CN (with a mean of 0.35 mg/L in alkali leaching). The measured concentration of cyanide and the PTEs was compared to the minimum permissible levels enforced by the South African Department of Water and Sanitation (DWS) and the Water Research Commission (WRC) regulations that govern the disposal of hazardous constituents into the environment. Additionally, it was observed that the concentrations of contaminants in the tailings exceeded the acceptable minimum limits for hazardous waste exposure, posing risks to the environment and human health.

Apr 16, 2024

Nine case studies are presented to illustrate how risks can be, minimised or quantified during pit optimisation, utilising Whittle Four-D software. Each case study covers a specific problem that has been encountered from a wide variety of pit optimisations. Case A: Maximising profits when the tenement owner is paid a royalty on tonnes processed. Case B: Allocating product prices, rather than a single commodity price during optimisation. Case C: Quantifying processing costs that are affected by penalty elements in the ore. Case D: Exploration expenditures below current pits can be quantified through the use of simulation techniques. Case E: Alternative strategies can be quantified when pits are restricted by tenement boundaries. Case F: Relocation of mine infrastructure that requires large capital expenditures, can be simulated by allocating costs to an area during optimisation. Case G: Evaluating alternative corporate strategies during pit optimisation. Case H: Sensitivity analysis for price, processing cost and mining cost. Case I: Quantifying the advantages of using additional mining capacity during the early periods of mining.

Jan 1, 1994

By R Zhang, X Huang, M Zhou, X Lv, C Bai

Iron ore sinter accounts for a large proportion of blast furnace ferrous burden in Chinese steel mills. Depleting high-grade iron ore resources and spreading complexity of iron ores in mineralogy and morphology have made it more difficult to utilise iron ores efficiently and economically. In this paper, the physical properties of iron ore particles were characterised using mechanical sieving, laser sizing and gas adsorption. From those measurements, two physical indices (fractal dimension of the particle size distribution and surface morphological factor) are defined as important variables for optimising the granulation performance of iron ores. The moisture capacity and the contact angle of iron ore particles with water were also measured to determine the strategy of water-feed in the granulation process. It can be concluded from the experimental results that an increase in the fractal dimension of the iron ore particles will lead to a better granulation performance, while an increase in moisture capacity with a range of 12.8 ~ 14.8 per cent would increase the optimum water content where the granule packed bed achieves its best permeability. Furthermore, the optimum permeability varies inversely with the moisture capacity of the sinter mixture.CITATION:Huang, X, Lv, X, Zhang, R, Bai, C and Zhou, M, 2013. Iron ore characteristics and their application in optimising the granulation process, in Proceedings Iron Ore 2013 , pp 261-268 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

Teleoperation is one method by which an operator can remotely control and monitor a vehicle. The operator monitors the status and progress of the remote vehicle by watching the video transmitted from one or more cameras which are mounted on the vehicle. In the case of an LHD, it will be fitted with three cameras. For a twin-boom Jumbo, four cameras are mounted on the drill, three of which will have remote pan, tilt, 15x zoom, focus and lens cleaning controls. The advantage of teleoperation is that an operator can stand in the drive and send the remote vehicle around a corner, completely out of sight and still clearly see what is happening. This means that an LHD returns with a full bucket and a Jumbo can be operated from a safe distance. Standing in the drive teleoperating vehicles, exposes the operator to passing traffic including the remote vehicle. There are two solutions to this problem. One is to equip the operator with a Nautilus æBuddyÆ jacket which will help to protect them from all vehicles. The other is to move the operator into a safe room or area, away from the fumes, the noise and the traffic. In this comfortable, less stressful environment, the operator will be more productive and less likely to accidentally damage the vehicle. The operatorÆs æsafeÆ room does not have to be a formal control room, it can be any area which has AC or DC power available and is large enough to contain a chair and a 1.5 m x 0.75 m table. The æsafeÆ room can be on the surface or underground, it does not matter to the operation of the Nautilus Equipment. If the LHDÆs, trucks, locomotives, etc are automatically guided from origin to destination, the operator is free to operate several vehicles at a time, performing only those tasks which are too difficult for a computer to do by itself.

Jan 1, 1998

By R Shrimali, P Rajmeny, L Shekhawat, A Joshi

Rampura Agucha open pit mine has successfully been excavated to a depth of 320 m, incorporating multistage working. The key to success is the implementation of presplitting as control blast measures at every stage of mining, including intermediate cut backs, in addition to the final wall. The major challenges encountered in establishing presplitting in the hang wall as compared to the footwall of the mine are:reversely dipping foliation, ie dipping into the hang wall itselfstriking obliquely at an angle of 20–30° with regards to the general strike of the pit wallthe presence of numerous geological planes of weaknesses like major faults, slips, etc.Control blast parameters like hole inclination, spacing and stand-off with buffer row were chosen initially from the literature survey and were subsequently fine-tuned by field trials to the mine geo-mining conditions of the hang wall. Electronic initiation used for trim blasts along with double presplitting in fault-affected zones helped in getting better presplit performance and resultant stability of the hang wall.CITATION:Rajmeny, P, Shrimali, R, Shekhawat, L and Joshi, A, 2015. Establishing the design parameters of a control blast for long-term stability of the hang wall at Rampura Agucha Mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 437–446 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

East Nelson and Marlborough, in the northeast of the South Island, contain a wide variety of metallic minerals, including gold, silver, copper, chromite, antimony and scheelite, but no sustained metallic mining industry has evolved. Gold was the most sought-after mineral during the first century of European settlement and numerous discoveries were made but these failed to live up to expectations. While traces of gold are widespread in east Nelson, including in quartz veins in Nelson City, no payable deposits were found. In Marlborough the probability of a gold discovery had initially seemed remote but all this changed with the finding of rich deposits in the bed of the Wakamarina River in 1864, which provided a much-needed boost to the provincial economy. However, the decline of gold mining in Marlborough began virtually as soon as it had commenced. Extensive floods in 1865 hastened the exodus of miners to the profitable new fields of the West Coast.

Jan 1, 1993

By Glasson K. R

The history of Ore Reserve classification and reporting in Australia is largely a history of the Australian mining industry itself. In the late 1800s, when the industry was dominated by small scale, high grade underground mines, Reserves (if estimated) were based on hand sampling and geological inference, and reporting of Reserves was either non-existent or of extremely variable quality. By the mid-20th century, the industry was dominated by large underground base metal and gold mines. Reserve estimation was coming under the control of skilled geologists and mining engineers, however Reserve classification and reporting standards continued to vary in type and quality from mine to mine. Today, large scale, low grade mining operations predominate, and Reserve estimates are generally based on extensive drilling results processed (with geological control) by computer. Through the efforts of a Joint Committee established by The Australasian Institute of Mining and Metallurgy and Australian Mining Industry Council, Reserve and Resource classification and public reporting has been standardised and controlled by adoption of the ""Australasian Code for the Reporting of Identified Mineral Resources and Ore Reserves"" released in 1989. The Code, which will continue to be modified and improved by the Joint Committee, has also been used as a basis for guides to reporting in other countries, and there is now some hope that this difficult and vexing topic may finally become subject to international standards and controls.

Jan 1, 1992

By A Melkumyan, K Silversides

The banded iron formation-hosted iron ore deposits located in the Hamersley Ranges of Western Australia contain marker shales that are used to distinguish lithology for geological and orebody mapping. These marker shales produce distinctive signatures in the natural gamma downhole logs, which are conventionally manually interpreted. This paper proposes an alternative method of automatically identifying these shales using dynamic time warping (DTW). A Gaussian processes (GPs)-based method for automatic identification is also considered. Both methods are tested on a deposit that contains the Marra Mamba sequence of the Hamersley Province.Both methods were trained to predict the location of the desired shales, and the resulting outputs were compared with a manual interpretation of the results to determine the accuracy. The GP method can identify signatures with an accuracy between 87.0 per cent and 92.0 per cent, which increases to 92.9 per cent and 95.7 per cent where the GP is certain. The DTW method has an accuracy between 90.0 per cent and 91.6 per cent, which increases to 94.0 per cent and 95.4 per cent where the DTW is certain.The GP method has several advantages, including a more automated library building process, a probabilistic output and a shorter run time. However, the DTW method was capable of accepting more distortion in the signature and therefore identified more signatures. This is important in a deposit where the signals are frequently distorted by events such as hydration and folding. Both methods provide a viable alternative to the current manual detection, but their differences make them applicable to different cases.CITATION:Silversides, K and Melkumyan, A, 2014. Comparison between Gaussian processes and dynamic time warping for classification of marker shales in iron ore deposits, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 177–184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

The discovery since 1990 of four major orebodies in the Mt Isa Inlier - Century Zn-Pb, Osborne Cu-Au, Cannington Pb-Zn and Ernest Henry Cu-Au - only serves to enhance the already high stature of the Inlier in world mining importance. Currently the known mineral resources of the Inlier represent about 11 per cent of the world's Pb-Zn resources, five per cent of the world's Ag resources, and one per cent of the world's Cu resources. More can be expected to be added to these impressive figures given that two-thirds of the Inlier remains obscured by younger cover. Individually, projects such as Century and Cannington may ultimately achieve `world's best' status; Century's proposed production of 450 000 tpa of Zn metal would rank it close to number one with Cominco's expanded Red Dog project in Alaska. Cannington, with projected production of 660 tpa Ag, could become the world's biggest producer of silver. For comparison, Mt Isa produced 170 000 t of zinc metal and 335 t of silver in 1995. The apparent physical diversity of deposits in the Mt Isa Inlier is matched by a great diversity of opinion as to their origins. Because Ernest Henry is hosted by `porphyries', it is described by some as a porphyry copper deposit, despite mineralisation age possibly post-dating volcanic age by 200 Ma. Cannington Pb-Zn could be a Broken Hill-type (BHT) exhalitive deposit, or a late epigenetic replacement `regional skarn'. Mt Isa - Hilton Pb-Zn deposits appear to have experienced all deformational events and he syn-diagenetic in origin, or may have experienced little of the above and be epigenetic replacement deposits formed late in the major Isan orogeny, some 150 Ma after deposition.

Jan 1, 1996

By J Safarian, D Hariswijaya

Treating bauxite residue as an alternative source of metals for iron and aluminium industry is an approach to promote circular economy in metal industries. Reduction of metal oxides with H2-based process is an important step on decarbonisation of metal industry. In this study bauxite residue pellets were prepared and were reduced with different H2-H2O gas compositions at different temperatures which yielded with various degrees of reduction. The bauxite residue pellets were made from a mixture of bauxite residue and Ca(OH)2 powders and sintered at 1150°C. Hydrogen reduction was carried out on the oxide pellets using a resistance furnace at elevated temperatures in controlled reduction atmosphere of H2-H2O gas mixtures which resulted in reduction of iron oxides in the pellets. Unreduced and reduced pellets were subsequently heated to 1400°C to study their smelting behaviour using differential thermal analysis (DTA) and thermogravimetric analysis (TGA) technique to investigate the evolution of phases related to slag formation via smelting. Equilibrium module of Factsage™ ver 8.1 was utilised to analyse results of thermal analysis. It was observed that Tricalcium phosphate-β (CaP2O8), Bredigite (Ca7Si4MgO16), Rankinite (Ca3Si2O7), and calcium alumino ferrite (Ca[Al,Fe]6O10) were formed during thermal analysis as intermediate phases. The initial slag formation for sintered and reduced pellets occurred at 900°C which mainly contains calcium and small amount of strontium component. The slag formation rate increases significantly starting from 1100°C when iron oxides started to form initial molten slag phase which then followed by other oxides dissolution in the system. Gas formation was observed at 1180°C and it was found that the gas to be released from unreduced pellets is O2 meanwhile the gas to be released from reduced pellets is SO2 gas. Gas formation rate for both pellets start to increase at 1280°C when the remaining chemically bonded gas start to be released from the system.

Jun 19, 2024

By J Zhou, D M. Hunter, S M. Iveson, K P. Galvin

The recovery and concentration of ultra-fine iron ore can provide significant economic benefits. Presently, there are limited options available given the low settling rates achieved by conventional gravity separation and the relatively poor performance of reverse flotation. The Reflux Classifier is a new water-based gravity separation technology that consists of a set of parallel inclined channels positioned above a vertical fluidised section. This arrangement promotes a powerful throughput advantage compared to conventional fluidisation and a highly selective hydrodynamic basis for achieving sharp separations. A high shear rate develops within the inclined channels, which generates sufficient hydrodynamic lift to convey the lower-density particles (even if they are relatively coarse) to overflow while retaining the high-density particles (even those that are ultra-fine) for discharge to the underflow. The technology has previously been used around the world on particle sizes in excess of 0.1 mm. The present work, however, is concerned with density-based separations down to much finer particle sizes approaching 0.01 mm.A major advantage of the Reflux Classifier technology is the achievement of simultaneous gravity separation and desliming via a single-stage separation. A series of continuous experiments was conducted using an iron ore feed with head grade of 35 wt per cent FeT and nominal top size of 0.106 mm, with 59 wt per cent being below 0.038 mm in size. At a low throughput of 1.5 t/(m2 h), the Reflux Classifier produced high-grade products at a high recovery. For the entire feed, grades of 66.1 wt per cent FeT with Fe recoveries of 80 per cent were achieved in a single-stage separation. Within the 0.020–0.038 mm size fraction, grades of 68.8 per cent were achieved with iron recoveries of 94.7 per cent. Excellent recoveries of up to 57.0 per cent were achieved for the -0.020 mm size fraction. The ability of the inclined channels to retain the fine dense material further enhances the effectiveness of the Reflux Classifier by creating an autogenous dense medium effect within the vertical section. This helps to elevate large gangue particles up into the overflow.CITATION:Hunter, D M, Zhou, J, Iveson, S M and Galvin, K P, 2015. Gravity separation of ultra-fine iron ore in the reflux classifier, in Proceedings Iron Ore 2015, pp 143–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By McDougall I, Claoue-Long J

A combination of high precision 40Ar/39Ar and U-Pb dating has been used to determine the age of hydrothermal minerals and host rocks in a number of Lachlan Fold Belt (LFB) gold deposits in New South Wales, Au4 ralii In particular, this investigation demonstrates that the UAr/ Ar technique of K-Ar dating can be used to determine the timing of mineralization in Palaeozoic systems.A close temporal link between mineralization and Late Ordovician to Early Silurian magmatism is indicated by the dating work. Hydrothermal sericite from the Goonumbla p8rph gy Cu deposit and Glendale Au prospect yieldsAt/ Ar step heating ages between 437.9 ¦ 1.1 and 441.2 ¦ 1.1 Ma (16), and4 minjrnum age of about 425 Ma has been obtained by Ar/ Ar dating of hydrothermal amphibole from the Browns Creek Au-Cu skarn deposit. Hydrothermal aluniI8 frog the Gidginbung epithermal Au deposit yields reset 44 Ar/ Ar ages of 401.0 ¦ 1.3 to 417.3 ¦ 1.3 Ma (16). U-Pb dating by ion microprobe on magmatic zircons from the vicinity of the Goonumbla and Gidginbung deposits gives ages of 438 ¦ 3.5 Ma (2 6), and 435 ¦ 2.5 Ma (2 (7) respectimly, W a minimum age of 435 Ma has been obtained by Ar/ Ar dating of magmatic phases from volcanic rocks adjacent to the Browns Creek skarn deposit. Magmatic episodes near the Sheahan-Grants gold skarnpost give ages of 479.2 ¦ 1.1 and 467.9 ¦ 4o1 by 'Ar/ 9Ar dating of magmatic amphibole. Most Ar/3yAr age spectra show the effects of partial Ar loss at between 360-420 Ma, probably due to heating caused by granitoid emplacement.The radiometric dating work in this paper suggests a restricted metallogenic epoch in the Late Ordovician-Early Silurian LFB, NSW, of similar duration to that found in the Andean margin and the western Pacific island arcs around the Pacific Rini.

Jan 1, 1990

By C M. Stewart, P Bowen

McArthur River Mine, in the Gulf Country of the Northern Territory, exploits one of worldÆs largest deposits of zinc, lead and silver. It was officially opened in September 1995, 40 years after its discovery in 1955. This paper describes the geological, engineering and metallurgical assessments which made up the feasibility study. It then relates how these study components compare with the first two years of operation. The challenges that had to be overcome before the McArthur River Mine became economically viable included the metallurgical problems associated with extremely fine grained ore and the development of an effective mining process.

Jan 1, 1998

This paper explores the use of a Process Safety Management (PSM) system to manage risk in the mineral processing and metallurgical refining industries. Important elements of a PSM system are described. International regulations and non-regulatory guidelines covering PSM for high hazard industries are reviewed. Case studies of incidents in the mineral processing and metallurgical refining industries are presented to understand the lessons learned from failure to manage risks using a PSM system. Conclusions are drawn to adopt PSM in the minerals and metals processing industry as a tool for loss prevention and risk management.

Jan 1, 2003

By R Barritt, P Scott, K Albano

Successful closure of tailings storage facilities (TSFs) is an environmental issue faced globally by metalliferous mines. During the initial feasibility and design phase of the mine life importance is placed on the physical stability of above ground TSFs, largely driven by legislative requirements, whilst closure planning is often a secondary consideration. However, as the landform is further developed and constructed attention must be paid to regularly revisit the original closure plan and update it to achieve the best (sustainable) possible outcome for both the environment and stakeholders. A mine in northern Queensland is in the process of developing a closure strategy at their TSF. Appropriate closure measures for the TSF are required to mitigate the impact of any seepage emanating from the TSF on the groundwater and surface water receptors. O’Kane Consultants Pty Ltd (OKC) have provided the mine assistance with the development of a TSF cover system design in order to appropriately manage tailings during operations and to prepare for the facilities’ closure. OKC has collected data since 2007 from cover system field trials located on the TSF. To enhance engineering judgement in the design of future cover systems, calibration of soil-plant-atmosphere numerical models to field data (referred as ‘field response modelling’) were completed. Calibrated model inputs can be used to provide insight into long-term cover system performance as well as a tool for design of the final landform.Following a site investigation, materials characterisation and numerical modelling program various cover system alternatives were developed. Two of the preferred cover system alternatives referred to as Test Plot #1 (TP#1) and Test Plot #2 (TP#2) (Figure 1), were constructed at the site and instrumented. Monitoring instrumentation comprised several nests of in situ volumetric water content and thermal conductivity sensors to measure changes in water content, temperature and matric suction within the cover system materials and underlying tailings waste. Run-off collection buckets and a fully-automated meteorological station were also installed. CITATION:Barritt, R, Albano, K and Scott, P, 2016. Findings and conclusions following ‘long-term’ cover system monitoring – refinement of the conceptual design for tailings storage facility closure, in Proceedings Life-of-Mine 2016 Conference , pp 85–88 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

The reasons for and the methods of inte- gration of the gold treatment plant with the existing nickel concentrator are discussed. The integration was accomplished in three stages commencing in May 1980 and attain- ing current throughput in December 1982. The problems encountered and their solution, including the design and construction of a new tailings dam are also discussed.

Jan 1, 1984

Olympic Dam Operation is located in the Stuart Shelf Geological Province approximately 520 km north-north-west of Adelaide in South Australia. It is estimated to be one of the worldÆs top five copper orebodies by size and the biggest single occurrence of uranium. The deposit was discovered by Western Mining Corporation in 1975. Exploration was based on a conceptual model for the formation of sediment hosted copper deposits together with gravity and magnetic anomalies.The capital cost of the current expansion is estimated to be A$ 1.64 billion. The underground expansion includes a total of 36 km of lateral development, a railway haulage system delivering ore from a series of ore passes to a new crusher station and a significant increase in ventilation capacity and mine services.In the current underground expansion the mining method will essentially remain unchanged. The ore handling system will incorporate some recent advances in technology, improving efficiency and safety standards.Major infrastructure excavations are designed by a team of engineers attached to the Olympic Dam Expansion Project and a number of consulting groups. Once the expansion is fully completed it is expected to increase the current annual underground production level from 3.4 Mt to 9.0 Mt of ore by the year 2000. Mine design engineers working for the Olympic Dam Operation have recently completed a three year final design plan to achieve this target.Access to the existing mine is through the decline and Whenan shaft. The Whenan shaft was originally sunk as an exploration access and later upgraded for hoisting. The 4 km long service decline connecting to the Whenan shaft was later constructed to accommodate the increase in service demand. The Robinson and Sir Lindsay Clark shafts were developed at later stages to cater for the hoisting during and following the expansion lead up.

Jan 1, 1999

By Mowat B. A

I lamata is within the Morobe Goldfield (7¦ 25' S, 146¦ 39' E) on the Wau (SB 55-14),1:250,000 scale map sheet (Fig 1). The deposit is 13 km SW of Wau, within the headwaters of the Upper Watut River, at an average elevation of 2000 m. The steep mountainous terrain is covered by dense tropical rainforest and access is by helicopter or by foot track. The deposit has been described previously by Wells and Young (1991) and 1)enwer. Leach and Mowat (1995). Data collected to late 1996 have been used to estimate an Inferred Resource of 9.2 Mt at 3.1 g/t gold using a cutoff of 0.5 g/t. This contains a high grade portion for which an Inferred Resource of 1.2 Mt at 9.7 grt gold has been estimated using a 5.0 g/t cutoff.

Jan 1, 1997

By A Van den Bulck, K Verbeken, O Vergote, I Bellemans

Viscosity is one of the most important physicochemical properties during pyrometallurgical operations. In the sub-liquidus regime, an important factor is the presence of suspended solid particles, yet its influence is not well-described in earlier literature, despite the significance of this factor. This project aims to determine the influence of spinel particles (Zn(Al,Fe)2O4) on the rheology of a multiphase synthetic PbO-SiO2-ZnO-Fe2O3-CaO-Al2O3 slag system. Three data sets with a wellcontrolled methodology and three different spinel sizes (small (13 μm), medium (34 μm) and large particles (76 μm)) were published previously, using a custom-built high-temperature rheometer. This study presents an additional data set of slag viscosity measurements, performed using a different apparatus, the Anton Paar FRS 1800, to verify the consistency of the earlier determined viscosity behaviour. Within this data set, no consistent trend could be found between the predicted wt per cent spinel and the relative viscosity. Therefore, additional quenching experiments were conducted to identify the morphology and experimentally determined volume fraction of the spinel particles in the slag. These measurements revealed a difference in spinel size across the samples and corresponding viscosity behaviour, emphasizing the importance of spinel particle size on slag viscosity. Once the spinel size was taken into account, consistent viscosity results (relative apparent viscosity and flow index) were observed across the two devices. This study confirms that, once all parameters affecting slag viscosity are considered, the viscosity behaviour of a heterogeneous slag can be uniquely determined. The resulting optimised slag viscosity models can be used to predict viscosity before processing, addressing relevant phenomena such as slag tapping, slag foaming and copper droplet settlement.

Aug 21, 2024

By K G. Harding, E L. Haggard, C M. Sheridan

Mining is a water intensive sector, contributing to declining water resource quality around the world. Improvements to current mine water management practices can help reduce the amount of water utilised by the mining sector and the impact on water resources. Creating a water account can help companies understand water use in their operations and identify areas where water reduction is possible. Water accounting methods include the Water Footprint Network method and the WaterMiner tool.The Water Footprint Network method is used to determine the amount of direct and indirect water used by an organisation either in a process or to manufacture a product. The total water footprint is divided into the blue, green and grey water footprints. Blue water is the amount of water abstracted from surface and ground water resources. Green water is the amount of rain water utilised. Grey water is the amount of freshwater required to assimilate the waste stream to the natural resource and still conform to ambient water quality standards.The WaterMiner tool is a program available via the internet, which can be used to model water use of mineral processing sites. The program reports the amount of raw, worked and treated water used by the process and recommends flows that can be added to reduce the amount of fresh water required by the process.To gain information on mine water management practices in South Africa, a water account for a platinum mine was developed using the Water Footprint Network method and WaterMiner tool. Based on the results, suggestions to reduce the amount of fresh water utilised are made.CITATION:Haggard, E L, Sheridan, C M and Harding, K G, 2013. Water footprint for a South African platinum mine, in Proceedings Water in Mining 2013 , pp 15-20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013