Search Documents

A new test coke oven of seven cubic foot capacity is described. The oven was designed to simulate conditions in a central section of a battery oven and a special feature is the achievement of unidirectional heating from the flues on either side of the charge. The method of charging permits close control of charge conditions'such as bulk density and moisture content. These conditions, as well as coking conditions (e.g. flue temper- atures., coking time) must be varied to simulate conditions in different batteries, The effects of several variables on coke quality are discussed. Using test oven conditions corresponding to those of Newcastle steelworks batteries, good agreement was obtained between strength indices of test oven and battery cokes; for 17 tests, the average A.S.T.M. stability and hardness indices for the test oven coke were 38,5% and 69.7%, while those for the battery coke were 37.1.% and 67.6%.

Jan 1, 1969

By Bothe C

Froth flotation processes use different surface properties of the minerals to be sorted. In an aqueous environment the hydrophobic mineral attaches selectively to air bubbles and is lifted to the surface of a separation vessel, while the tailings settle towards its bottom. Besides the surface properties, the hydrodynamic conditions play an important role. With respect to the hydrodynamics the flotation process can be divided, for simplicity, in two sub-processes. The attachment of hydrophobic particles to air bubbles, the so-called mineralisation, demands a large number of collisions and therefore high turbulences. The phase separation however needs a deterministic movement of both the particle-bubbles-aggregates and the tailings particles and therefore a quiescent flow field. The optimisation of the overall process requires a separation of both sub-processes, especially when fine particles have to be sorted. In conventional mechanically agitated flotation cells both sub-processes take place in the same turbulent volume. For this reason they suffer from a decreasing selectivity with decreasing particle size. In flotation columns the mineralisation of air bubbles and the phase separation are performed in a quiescent environment. This results in high concentrate grades and at the same time in a very slow attachment kinetics, which must, especially for fine particles, be counterbalanced by a long residence time of the slurry.

Jan 1, 1993

By Dendyuk TV

The possible use of combined (flotation/magnetic separation and magnetic separation/flotation) technologies involving the new flotation reagent systems for upgrading the iron ore concentrates, low grade manganese products and beneficiation of graphite-bearing dusts from integrated iron-and-steel works has been shown. It has been found that the absence of magnetic flocculation phenomenon worsens the reverse cationic flotation of oxidised iron ore concentrates and direct flotation of low-grade manganese products which require the use of modifiers possessing the flocculating properties. The synergetic mixtures of polymers have been proposed to be used as modifiers, ie polyacrylamide (PAA) with carboxymethyl cellulose (CMC) and polyacrylamide with industrial lignosulphonates (LST)

Jan 1, 1993

By T Angerer, N H. Maund, S Hagemann, D R. Cowan

Cliffs Natural Resources Pty Ltd - Asia Pacific Iron Ore's (formerly Portman Iron Ore Limited) K deposit (Dowd's Hill), at its Koolyanobbing operation in Western Australia, hosts enriched magnetite mineralisation below the presently mined haematite-goethite ore zone. Two distinct northwest-southeast elongated, highly magnetic anomalous bodies that dip to the north-east appear to be sourced by this deeper mineralisation. Magnetic modelling indicates significant remanent magnetisation with Qratios around 1.5, directed shallow down. The north-west anomaly is overlain by a ridge of uneconomic banded iron formation (BIF) and the present waste dump, whereas the south-east body was partly exposed during ongoing mining of overlying haematite-goethite ore. Sections of the magnetite mineralisation in this south-east anomaly were intersected previously by diamond drill holes. Review of the historic cores identified potential magnetite enrichment, with grades and mineralogy that might be amenable to beneficiation. A first-phase reverse circulation drilling program was designed to further delineate the trend and extent of the two anomalies. The following magnetite mineralisation assemblages are recognised from cores, reverse circulation (RC) drill cuttings and pit mapping of the south-east magnetic body: higher-grade magnetite-haematite ¦ goethite and magnetite ¦ pyrite and lower-grade, recrystallised magnetite-quartz (BIF), magnetite-carbonate, magnetite-talc and minor magnetite-bearing mafic schist. Disseminated specularite is locally present in theassemblages. Talc-schist and massive pyrite occur along the footwall contact. Magnetic susceptibility measured from drill chips within the magnetite-enriched zones reveals an apparent susceptibility values range of 0.2 to 1.3 SI. Preliminary results from Satmagan and Davis tube recovery analysis shows that the magnetite content in these mineralised zones correlate well with existing geophysical data and magnetic susceptibility measurements.

Jan 1, 2009

Stope filling practice on the Great Boulder Mine was described in -a paper published in Aus.I.M.M., Proceedings No. 137, in 1945. When the paper was presented the process had emerged from the experimental stage, most of the initial operating difficulties had been overcome, and it had been established that this method of filling was suitable for the working of ore bodies in the Kalgoorlie field: Since 1945, it has fulfilled its early promise, -and during 1947, the tonnage of fill placed was sufficient to cover current operating requirements as called for by the mine ore breaking programme. The object of this paper is to outline current operations. In so doing it will refer' to some ground covered by the previous paper, but will omit details of the initial experimental work. It will include, however, a description of further experimental work on the use of hydraulic filling for worked-out shrinkage stopes, arid will provide more accurate data on costs than were available previously.ESTIMATE OF TONNAGE OF FILL REQUIRED.Early in 1946, the mine ore reserves were analysed in order to estimate the relative tonnages to be mined per four-weekly period by shrinkage stope methods -and by cut and fill stope methods respectively. This analysis was extended beyond the blocks already prepared for stoping, and inclqded the majority of the major ore blocks in the mine ore reserves. It gave the following results:-For a mill tonnage of 28,000 tons per period, 6,933 tons were required from cut and fill stopes, and a possible future maximum programme of 35,000 tons per period would require...

Jan 1, 1948

By C Boyle

Brockman 2 mine is located in the Pilbara of Western Australia and is operated by Rio Tinto Iron Ore. Mineralisation is hosted by synclines where there is structural complexity to focus fluid flow. Mineralisation is hosted by the Brockman Iron Formation. Mining is on 10 m benches and blastholes spaced at 6 - 8 m apart are geologically logged, sampled by shovel cuts, and assayed using X-ray fluorescence for ten chemical variables. Blast blocks are digitised by mine geologists to assign destinations of material within blasts. Resource evaluation drilling is on a spacing of 50 m × 50 m across known mineralisation and consists of recent reverse circulation drilling and older open hole percussion drilling. Sampling of resource evaluation drilling is by rotary splitters or riffle splitters, and assaying is by X-ray fluorescence for ten chemical variables. Ordinary kriging of resource evaluation produces a long-term resource model. This study examines whether mine planning would be improved by using a blasthole estimate to extrapolate grades into deeper benches and merging the blasthole estimate with the long-term model made using resource evaluation drilling. The two estimates are merged into one model using an inverse weighting based on kriging variance. However, reconciliation results in a test bench show the original estimate made using resource evaluation drilling more closely matches mine geology block outs than does the merged model. This is due to a local trend of more high grade and higher iron grades of high grade in the area. The blasthole estimate of deeper benches must use extrapolation and it is diffi cult to take local trends into account. In contrast, the estimation using resource evaluation drilling is mainly interpolation and is better able to handle local trends.

Jul 11, 2011

By A Woodley, N C. Kunz

A mine site water balance is important for communicating information to interested stakeholders, for reporting on water performance and for anticipating and mitigating water-related risks through water use/demand forecasting. Gaining accuracy over the water balance is therefore crucial for sites to achieve best practice water management and to maintain their social license to operate. For sites that are located in high rainfall environments the water received to storage dams through run-off can represent a large proportion of the overall inputs to site; inaccuracies in these flows can therefore lead to inaccuracies in the overall site water balance.Hydrological models that estimate run-off flows are often incorporated into simulation models used for water use/demand forecasting. The Australian Water Balance Model (AWBM) is one example that has been widely applied in the Australian context. However, the calibration of AWBM in a mining context can be challenging. Through a detailed case study, we outline an approach that was used to calibrate and validate AWBM at a mine site. Commencing with a data set of monitored dam levels, a mass balance approach was used to generate an observed run-off sequence. By incorporating a portion of this observed data set into the calibration routine, we achieved a closer fit between the observed versus simulated data set compared with the base case. We conclude by highlighting opportunities for future research to improve the calibration fit through improving the quality of the input data set. This will ultimately lead to better models for run-off prediction and thereby improve the accuracy of mine site water balances.CITATION:Kunz, N C and Woodley, A, 2013. Improving the accuracy of mine site water balances through improved estimation of run-off volumes, in Proceedings Water in Mining 2013 , pp 267-272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Gillies A. D S

The active history of foreign investment in the mining industry has resulted in Australia emerging as a major world producer of a range of mineral commodities. The current contribution to the national economy represented by mineral production and export revenues would not have occurred without both capital and expertise provided by foreign investors in the past. The initial foreign investment has led to the formation of Australian majority owned and controlled multi-national mining groups such as BHP Limited, CRA Limited and MIM Holdings Limited. These Australian companies, and others, are playing a significant part as foreign investors in the mining industries of Papua New Guinea (PNG) and Indonesia. The study examines issues of importance in foreign investment in each of the countries. It concludes that in Indonesia, the nationalisation of the Dutch mining industry in 1957 did much to deter foreign investment. The remarkable degree of policy stability brought about by the Contract of Works system since 1967 has gone a long way to restoring that confidence. The level of investment in the Indonesian mining sector is steadily increasing. Its attraction to Australian investors is a combination of policy stability, favourable fiscal terms, geological prospectivity for a range of commodities and proximity to Asian markets to the north. PNG has a stable policy regime which until recently has been free from political interference at the administrative level. As such, investors were developing confidence in the system and investment was progressively increasing as evidenced by growing exploration expenditures up to 1988. The 1989 Bougainville revolution caused a re-assessment of PNG's investment and country risk. The recent Mt Kare incident has further raised concerns over the government's ability to guarantee internal security. Foreign investors are faced with weighing concerns with the risks of operation in PNG against the undoubted geological prospectivity of the country. The fiscal regimes of Australia, Indonesia and PNG were compared by means of a simulated open pit gold mine in each country. The effect of taxation is examined by reference to the relative change in project internal rates of return (IRR). The comparison of the relative differences between pre-tax and post-tax IRRs provides a measure of the relative attractiveness of each fiscal regime.

Jan 1, 1994

By Z U Bajwah

During the Palaeoproterozoic, a large number of granitic intrusions were emplaced in the various parts of the Pine Creek Geosyncline (PCG). In the central region, the granitic magmatism is represented either by the coalesced mass, eg the Cullen Batholith, or individual plutons such as the Mount Bundey Granite which together with the Mount Goyder Syenite intrude the metasedimentary strata, causing wide spread contact aureoles. Some of these granitic intrusions are temporally and genetically related to gold (and less commonly base-metals) mineralisation present in the adjacent metasediments. These plutons are characterised by the presence of biotite and homblende which appear late in the paragenetic sequence. Electron microprobe analyses of biotite and homblende show that these minerals are poorly to moderately zoned. Biotites are characterised by a decrease in Fe/(Fe + Mg) ratios when plotted against AIVI. Similarly a modest decrease in Ti from centre to the margins of the biotite crystals has also been observed. Furthermore, an increase in Mg/(Mg + EFe) ratios from centre to the margins as well as in mafic to felsic rocks is also apparent. On the other hand, homblendes from the granitic bodies display less well marked trends and are poorly zoned. However, they show systematic increases in Mg/(Mg + EFe) ratios, and decreases in Fe, Al"' and Fe/(Fe + Mg) ratios, when plotted against Si. Magnetic susceptibility measurements on powdered samples of the plutons give results characterised by high values ranging from 0.8 x 10-4 to 2.0 x 10-3 emu/g which place the granites in magnetite- series field. This indicates that the oxidation state of the magma was high during crystallisation. The range of chemical compositions of the mafic phases indicates a rise in the oxidation state of the magma as it progressively became saturated in H20-volatiles and other metals, not partitioned into the earlier crystallised phases in the final stages of magma consolidation. These variations in chemical compositions also indicate that initially fOz was high and became progressively higher during fractional crystallisation of magmas; this subsequently led to the emanation of hydrothermal fluids responsible for the mineralisation in the adjacent metasediments.

Jan 1, 1994

By H Weitz

Bateman Engineering provided process technology and engineering design to China Yunnan Metallurgical Company (CYMCO) for a 30 MW DC furnace for the production of high-grade titanium dioxide slag.Following the successful commissioning of the furnace during the latter part of 2009 and the first quarter of 2010, a period of adverse circumstances resulted in having to operate the furnace without feed and at a low power input for a period of time. When normal feed resumed, a layer of solid material was detected on the slag-iron interface during sounding measurements. The condition of the iron was also significantly altered. The iron temperature was much higher than the design value, but the carbon content had decreased to such an extent that a large amount of iron solidified in the furnace, which made iron tapping very challenging. The slag temperature was increased in order to melt the solidified iron. However, severe sidewall damage resulted, which finally led to a burn-through. A number of samples were taken from the slag that remained in the furnace. These samples were analysed to determine the chemistry and phase profile throughout the slag bath. The mechanisms of formation of the high melting-temperature phase on the slag-iron interface are discussed, as well as procedures that can be applied to prevent a recurrence of this phenomenon. Some recommendations are made for instances when furnace feeding is interrupted for an indeterminate period.

Oct 5, 2011

By K G. van den Boogaart, U Mueller

"An accurate prediction of benefit for some types of ore may require not just the ore grade, but a whole compositional characterisation of the estimates; that is, its full mineral composition including waste composition and nuisance elements. An example is Nickel laterite ores, where Ni/Co content must be complemented by estimates of many other elements, as these might have a notable impact on ore processing.Estimates are often obtained with (co-)kriging or co-simulation; however, geostatistics applied to compositional data may yield spurious and inconsistent results because of the constant sum constraint. The log-ratio approach avoids such problems. It proposes a three-step procedure: data are mapped to a set of log ratios of components; for example, the additive log-ratio transformation (alr) transformed scores are modelled with an appropriate fully multivariate geostatistical toolbox; for example, direct/cross-semivariograms and co-kriging or co-simulation results are back-transformed to the original units.Some practical aspects may make the application of this technique difficult: the assumption of Gaussianity and the high dimensionality of the compositions combined with the need for using multivariate methods. This contribution compares several ways of treating compositional data (combining normal score transformation, log-ratio transformations, and minimum/maximum autocorrelation factor (MAF) decomposition) with respect to their ability to generate sensible simulations. The various approaches considered are illustrated with a Nickel laterite data set for which ten variables are available. Both theoretical considerations and illustration results suggest that the best combination is (log)ratio-normal score transform-MAF, in this order. The factors so obtained are closer to Gaussian, approximately spatially decorrelated and can be simulated independently. Simulations can later be recombined to alr-simulations, which in turn may be converted back to point compositions. The resulting simulated compositions are compared with a full Gaussian co-simulation of the raw data. The log-ratio methods show reasonable to good reproduction of mean values, and distribution of the data set and by construction satisfy the total sum constraint, in contrast to the simulations based on raw data for which the total sums fluctuate strongly.CITATION:Mueller, U, Tolosana-Delgado, R and van den Boogaart, K G, 2014. Approaches to the simulation of compositional data – a nickel-laterite comparative case study, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 61–72 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

By P Brown, M Nagarajan, A Green, P Dare-Bryan

Coal loss is an important issue at many coalmines, with losses of five per cent being common. The type of loss varies from mine to mine but is dependent on mine strata, the drilling and blasting processes applied and the mining method used. Typical coal loss mechanisms from the drill and blast process are coal roof damage and edge loss. Usually a reduction in coal loss is in direct competition with the need to provide material that is well-fragmented and a muck pile that has the required cast percentage. These competing issues were addressed over a two-year period at a mine in the New South Wales Coalfields by implementing a five-step approach. This was centred around building an understanding of the coal loss mechanisms utilising proprietary heave- modelling software, measuring coal losses by comparing survey to drill and/or gamma logs and implementing appropriate coal loss reduction processes. The end result exceeded expectations with a 95 per cent reduction in coal loss. Mine excavation productivity was maintained and coal loss minimised to less than one per cent of the in situ coal block.CITATION:Nagarajan, M, Green, A, Brown, P and Dare-Bryan, P, 2015. Managing coal loss using blast models and field measurement, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 429–436 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By W R. Adamson

"Optimisation of drill and blast design and engineering can deliver a significant positive impact on the profitability of any mining operation; however, true engineering of the blasting process is less common than might be thought. The paper that follows explores this gap and suggests a process control-based approach to the challenge.The concept of applying modifications to drill and blast designs in order to achieve efficiency improvements in downstream mining processes is far from new. However, the author suggests that the practical application has become less than rigorous in a number of different sectors of the mining industry in a wide range of countries.There is a common tendency for the design process to become simplified to the point where the objective is merely the communication of instructions to field implementers (drillers, explosive suppliers, blasters, etc). In effect ‘design’ often degrades to ‘cut and paste’ with consequences that vary from mild to critical, with respect to the profitability of the business.Engineering of the drill and blast process involves the design function, not on a one-off basis but rather as a component of a more complete cyclical process that includes a statement of objectives, a design based on a suggested hypothesis, field measurement of results, comparison with the target ‘set point’ and the application of control measures followed by new measurement, including interpretation of the results in financial terms.When applied in this fashion, engineering provides practitioners with the means to optimise the drill and blast impact on the full spectrum business result of the mining activity.These concepts are discussed with reference to a surface gold mining operation applying run-of-mine heap leach extraction. Engineering optimisation by adapting process control and measurement techniques is demonstrated to be a key component of the solution set applied to generate enhanced operations productivity and stakeholder value. It is shown that a combination of rigorous measurement, model calibration and hands-on quality assurance/quality control facilitates the creation of a road map to profitability, stressing the need to consider economic trade-offs between operational expense (investment) and measurement of enhanced value (return on investment).The process, however, does not cease at this point. Implementation of true design practices, incorporating innovation and discipline in implementation or execution can drive the process to deliver demonstrable, technically validated outcomes. Furthermore, these technical results can be related to financially quantifiable impacts. However, this accomplishment does not guarantee that these gains or savings will reach the bottom line of those mining, quarrying and construction companies that begin the process with such high hopes.CITATION:Adamson, W R, 2015. Application of engineering discipline and a full-process optimisation focus – productivity to profitability without profuse pruning, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 3–12 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 24, 2015

By R Castroviejo, E Pirard, L PTrez-Barnuevo

Process mineralogy provides the mineralogical information required by geometallurgists to address the inherent variation of geological data. The successful beneficiation of ores mostly depends on the ability of mineral processing to be efficiently adapted to the ore characteristics, liberation being one of the most relevant mineralogical parameters. The liberation characteristics of ores are intimately related to mineral texture. Therefore, the characterisation of liberation necessarily requires the identification and quantification of those textural features with a major bearing on mineral liberation. From this point of view, grain size, bonding between mineral grains and intergrowth types are considered the most influential textural attributes. While the quantification of grain size is a usual output of automated current technologies, information about grain boundaries and intergrowth types is usually descriptive and difficult to quantify to be included in the geometallurgical model.Aiming at the systematic and quantitative analysis of the intergrowth type within mineral particles, a new methodology based on digital image analysis has been developed. In this work, the ability of this methodology to achieve a more complete characterisation of liberation is explored by the analysis of chalcopyrite in the rougher concentrate of the Kansanshi copper-gold mine (Zambia). Results obtained show that the method provides valuable textural information to achieve a better understanding of mineral behaviour during concentration processes. The potential of this method is enhanced by the fact that it provides data unavailable using current technologies. This opens up new perspectives to the quantitative analysis of mineral processing performance based on textural attributes.CITATION:PTrez-Barnuevo, L, Castroviejo, R and Pirard, E, 2013. New perspectives on quantitative textural analysis, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 191-198 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By J Shillabeer

Paste backfill has been adopted by many underground mines in North America and a growing number elsewhere. Paste offers a number of advantages. This paper suggests wider applications of paste technology to surface tailings disposal and water management. Advantages include improved overall stability, potentially easier permitting, smaller water inventory and earlier reclamation. It may be feasible to use the same plant to prepare backfill and to dispose of surplus tailings. Example cost models are given to illustrate potential applications.

Jan 1, 1998

Valuers of mineral properties should be aware that accountants are a major user of their opinions of value. Reliance by accountants can range from obtaining comfort that book values in balance sheets are not overstated to establishing values by which to assess the fairness of a takeover offer. Accountants using mineral property valuations clearly can't be expected to have the same level of expertise as the valuer and ""second guess"" the valuation. But they do have an obligation, under the ASC guidelines and their own professional standards, to'check the logic and reasonableness of the valuation before being able to rely on it. This means reviewing the valuation report for general sensibility, discussing the methodologies and assumptions with the valuer and being satisfied as to his competence and independence. This paper outlines how accountants use mineral property valuations, the level of scrutiny applied to such valuations and the problems commonly encountered in practice by accountants seeking to rely on them. The paper also explains how values of-mineral properties are established in company balance sheets and why these often differ, quite validly, from fair market values.

Jan 1, 1994

By A G. Guinea

If you were reading this article in a newspaper or similar in the 1800s, you would know that the world was firmly in the grip of the Industrial Revolution. You might have been one of the families that decided that an agriculturally based existence was no longer for you, and that the promise of a factory job was more appealing and more secure. And it was. Financially at least. Not so much from a workplace safety perspective.

May 5, 2022

By S Jayakumari, E Ringdalen, V Canaguier

Silicomanganese (SiMn), containing approximately 16–30 per cent Si, is produced in submerged arc furnaces using various Mn sources and quartz as the primary raw materials, along with fluxes and reductants. In the high-temperature zone known as the coke bed, a silica-rich slag is formed. SiMn is produced through the reduction of SiO2 from the slag. Dissolution of quartz into slags with different compositions, the primary slag formed from the Mn sources and flux before any MnO reduction occurred, representing conditions at the top of the coke bed, and dissolution of quartz into a partially reduced slag to simulate conditions inside the coke bed has been investigated. Experimental investigations were carried out to study the dissolution of quartz particles of varying sizes, 5 mm and 25 mm in synthetic slags with different compositions at temperatures between 1400°C and 1600°C, with varying holding times. Observed results are compared with liquidus compositions and equilibrium phases for original and formed slags. Particle size has been shown to be of little importance for the dissolution. Quartz dissolved more easily in slag at top of the coke bed than slag in the coke bed. Complete dissolution was observed after 30 mins at 1600°C in all cases, but not after 0 mins.

Jun 19, 2024

Remote sensing techniques can be used to map joint sets in a rock mass for the estimation of in situ block size distribution and improved optimisation of blasting. This paper reviews remote sensing using photogrammetry and laser mapping for mapping rock masses and presents elements of the analyses applied to data acquired with these mapping technologies. These techniques enable a user to map areas of hundreds of square metres rapidly with high precision. Using this data computer programs such as Sirojoint can provide estimates of joint position and orientation with orientation measurement accuracies better than one degree. The paper describes the use of remote mapping and provides potential users with a description of some of the advantages and limitations of the mapping techniques and the data they produce. Mapping of lithology and structure of rock masses is an important task required in many areas of mining and construction. It is a complex task routinely performed using established techniques developed to provide consistent results under a wide range of conditions. The techniques for data acquisition and analysis described in this paper enable more accurate mapping to be performed rapidly and enable mapping of inaccessible sections of a rock mass. These techniques will provide geologists and geotechnical engineers with more detailed, accurate data than previously available.

Jan 1, 2001

By Grossi M, Baiden G

This paper describes a new mine backfill method based on a newly invented binder with several years of test results from laboratory and on- site applications. The new binder has several advantages over traditional Portland and slag cement binders. One tonne of the new binder can replace two to three tonne of Portland cement when used to consolidate backfill and can result in the same compressive strength within seven days. When comparing backfill slurries of the same pulp density, the new binder attains more volume of in-place backfill mass than Portland cement because of the high crystallisation of water, resulting in tightly filled stopes. The crystallisation of the water provides for less or no de- watering in the backfill stope and easier transportation of the backfill slurry. Pastefill performance can be achieved by using pulp densities typical of a hydraulic backfill and the new binder, all the while transporting with the same ease of hydraulic fill.

Jan 1, 1998