Search Documents

By G Jones

The Singapore Land Transport Authority (LTA) has been procuring the expansion of their underground mass rapid transit rail network at a prodigious rate since the first line opened in 1987. Four lines (149 km) are currently operating and several more lines are at various stages of planning/construction; one of these is the Downtown line stage 2 (DTL 2).DTL 2 contract C917 was awarded in September 2009 for S$320 M. On 18 June 2013 the original contractor became insolvent, leaving the works incomplete. Following a fast-tracked tender process, McConnell Dowell was awarded the S$254 M contract on 29 August 2013 to complete the works. This contract includes two underground stations constructed by cut-and-cover methods and twin bored tunnels between the stations. Each tunnel is 1400 m long, excavated by earth pressure balanced (EPB) tunnel boring machines (TBM) at an average depth of 20 m and segment lined to 5.8 m inner diameter. The tunnel alignment is located under a busy five-lane road lined with prime residential real estate and congested with utilities.To compound the difficulty the tunnels are located within the notorious Bukit Timah Granite formation. This has a very wide range of strength, from below 1 MPa to over 300 MPa. This strength range is a consequence of six weathering grades, from soil to fresh rock, with the fresh granite causing severe abrasion problems. The various grades can occur within a very short distance of each other. Consequently, the problem of supporting a mixed face exists, particularly in the intermediate weathering grades where intact rock is encountered in the invert and corestones within a loose soil matrix in the crown, which can increase the instability by allowing the ground to flow into the TBM.The focus of this paper will be the excavation of the bored tunnels by EPB TBM used by McConnell Dowell to complete these challenging works.CITATION:Jones, G and Shepherd, J, 2014. Earth pressure balanced tunnelling in a dense urban environment, C917A, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 41–50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By A Mooney, J Marsden, H Grosser, G Dunstan

Carrapateena is a copper-gold deposit hosted in a brecciated granite complex, located 500km North of Adelaide, South Australia. The deposit is being mined using the Sub Level Caving (SLC) Mining method at a rate of 4.25 MTPA. The Carrapateena SLC construction was completed in Q4 2019, with ramp up to a mine production rate of 4.25 MTPA completed within 12 months; ~ 6 months earlier than originally planned (OZ Minerals, 2020b). Traditional SLC designs have had issues with safety interactions on production levels, namely at the perimeter drive, as well as presented challenges for the application of automation due to frequency of activity required to achieve ring turnover rates. Safety in design provides an opportunity to learn from experience at recent modern SLC operations and by considering hazards early in the design process minimise exposure and improve safety, productivity and automation of mining activity. This paper discusses the work carried out during the Carrapateena feasibility study and optimised during project execution; to update the SLC production level mine design, with a layout known as the Carrapateena Crows Foot Level Layout. This paper focuses on: • An introduction to the Carrapateena Operation and mine plan. • An overview and historical challenges of traditional level layout. • An introduction to the Carrapateena Crows Foot level layout, including production level design parameters as well as development metres and productivity comparisons. • Outlines the benefits of the Crows Foot design for safety in design of SLC operations. Provides a roadmap for improved production efficiency, level operational philosophy and the application of automation within the SLC.

Mar 15, 2021

By Stone I

Tahmoor Mine is located in the southern Sydney Basin 80km south-west of Sydney and produces 1.2 MT of Bulli Coal annually. Bord and pillar methods used to date will be supplemented by a longwall system. Difficult roof conditions have been experienced since mining began in 1979. A dominantly horizontal stressfield promotes shear failure in the thinly interbedded roof sequence of shales, laminites, siltstones and fine sandstones. General roof conditions and failure characteristics are related to the angle between the roadway direction and the principal horizontal stress direction. The apparent stressfield changes direction, magnitude and the ratio of principal horizontal components across the mine workings in response to both in situ and mining induced causes. Initial roof support of 5 x 2.1 m bolts per W-strap at in intervals, with mesh, was upgraded to include RSJ's in order to support areas of failed roof. This support system was inefficient and costly. A third system of support emphasizes roof reinforcement with full resin encapsulation of 2.1 m bolts in W-straps. The number of bolts per strap (6-8), extra butterfly straps and bolts, and W-strap spacing is determined for each area by expected roof and stress conditions. Intersections are pre-bolted and ribs are supported in some areas. Pillar dimensions, order of drivage and roadway width have each been altered to improve roof control. The intensity of roof deformation at the face varies from panel to panel and causes development rates to decrease to 30% of the maximum. 1. Manager, Tahmoor Mine, Tahmoor, N.S.W. 2. Senior Geologist, BP Coal, Picton, N.S.W. Roof conditions in each area of the mine are characterised and then projected to future development areas based on the relationship between stressfield orientation, relative roadway direction and face conditions. Planning information available includes expected development rates, roof support requirements and areas of changing conditions. Future improvements of strata control involve defining support design parameters for the range of mine conditions already seen at Tahmoor.

Jan 1, 1986

By B Beamish

The concept of a ‘critical velocity zone’ in the longwall goaf environment for the development of a spontaneous combustion event has been supported by numerical modelling. However, there is no experimental data available for Australian coals to show ventilation effects on the self-heating incubation behaviour of broken coal in the longwall goaf. A preliminary study using incubation testing has been completed on three high volatile bituminous coals (A, B and C) with R70 self-heating rate values of 3.86°C/h, 3.15°C/h and 2.09°C/h and moisture contents of 11.3 per cent, 3.9 per cent and 4.7 per cent, respectively. Mass to flow rates used in the adiabatic oven reaction vessel have been selected to be indicative of a sluggish, natural air leakage and medium ventilation environment. Under a sluggish ventilation flow rate all three coals incubate to thermal runaway in minimum time frames of 2.8–3.1 years, 34–42 days and 79–95 days, respectively. When the ventilation flow rate is increased to natural air leakage, coal A with the highest R70 value and highest moisture content selfheats to 28°C above mine ambient temperature before heat loss takes over due to moisture evaporation. However, both Coals B and C at this flow rate incubate to thermal runaway in a shorter time frame than under sluggish flow. At the medium ventilation flow rate, only Coal B incubates to thermal runaway, albeit after a significant extended period of time. These results show how important it is to determine the heat balance between the coal intrinsic reactivity (as indicated by the R70 value) and moisture content. The results also have implications for the possible location of the ‘critical velocity zone’ and subsequent hotspot development and migration.

Oct 12, 2022

By H Rossiter, A Maddever, J Market, P Jeanneau, A Virani

It is generally acknowledged that the head grade of the world’s copper resources is declining. Accordingly, there is an increase in the volume of resource material being mined and processed to maintain copper production. This has led to increases in cost base accompanied by reductions in Life of Mine (LOM) Net Present Value (NPV). The higher tonnages of material mined are driven by increased quantities of lower grade material required to satisfy the short term mine model. In turn, this has brought an increased focus on sampling and assay methods, since any error associated with estimating the grade of each block and determining its correct destination serves to magnify the losses that will occur. Presently most open-pit copper mining operations use blasthole sample assays to feed their shortterm model. The problematic nature of blasthole sampling is well documented (Engström, 2017), particularly the poor timeliness of the data and the significant errors that are inherent to the technique. Methods to improve grade control, such as drilling a separate grade control grid, have been proposed but come with their own cost, logistical, and accuracy shortcomings. A recent development in grade estimation is the Pulsed Fast and Thermal Neutron Activation (PFTNA) downhole logging probe. Deployed on an efficient semi-autonomous platform, PFTNA is being aggressively adopted in the Australian iron ore industry. The technology provides in-situ elemental analysis of the geological formation, delivering high accuracy, high efficiency, near realtime data from a sizeable measurement volume. In this paper we consider the application of the technology to copper. Whilst there are several operational components to such a value proposition, we focus on the benefits of improved gradeestimation. A simulated copper mine is used to model the quantum of improvement expected from a reduced grade-estimation error, which reduces the likelihood of misallocating material to the wrong destination, which in turn increases NPV.

Nov 10, 2020

By R Varden

Friction rock stabilisers, commonly termed ‘Split Sets’, friction rock bolts, or continuous friction coupled bolts are the most widely used rock bolt in the Australian underground metalliferous industry. Historically, they were used for temporary reinforcement, mainly within ore development. However, their use as primary reinforcement has grown with the demand for higher development rates at lower costs. The introduction of galvanisation has increased their longevity and pattern bolting in conjunction with weld mesh, specifically made for use in development headings, has allowed the use of friction rock stabilisers to increase rapidly with development jumbo’s undertaking the installation. The installation of friction rock stabilisers appears to be deceptively simple, particularly when compared to resin encapsulated bolts. The friction rock stabilisers capacity is a function of the borehole parameters, rock mass quality/strength, the bolt dimensions and steel quality, and lastly and perhaps the most important the operator skill levels. However, as in industry we are still seeing common occurrences of friction rock stabilisers not reaching their design pull test capacity. Pull testing the friction rock stabilisers is used to verify the installation of the design capacity. It involves loading the collar of the bolt with a hydraulic ram until the design load is reached or the bolt slips. Pull tests often show failure rates of 20 per cent or higher. This is despite over 40 years of use and with millions of units installed annually. Such high failure rates would suggest there remain issues with the quality of installation. Ground support quality assurance and quality control (QAQC) programs are needed in combination with operator training to ensure that pull test failure rates are kept as low as practical. However, there are times when despite the QAQC being completed the pull test failure rates increase quite suddenly. When this occurs, it is important to conduct a thorough investigation. These investigations often show there are several factors that are not obvious to personnel installing the bolts. To complete a useful investigation, it must also be done methodically, working through the entire process that includes less obvious factors such as steel quality and the calibration of the hydraulic pull test kit. The aim of the paper is to give mine practitioners an understanding of the complexities of friction rock stabilisers, what QAQC requirements they should be doing on-site, what can go wrong during installation and, if necessary, a process of how to conduct investigations into high friction rock stabiliser pull test failure rates.

Mar 29, 2023

By M R. Asef

Although generation of environmentally harmful hydrogen sulfide is considered to be related to sour gas fields, sweet gas reservoirs and waste fluids, travertine springs and geothermal fields may also produce acid gas (H2S and CO2) under certain conditions. The potential parameters influencing such a possibility need to be fully investigated to evaluate the extent of the consequences and predict hydrogen sulfide generation accordingly. Reports on hydrogen sulfide production at different regions and fields were gathered worldwide for the cases when some of them did not have such a problem previously. In order to inspect different aspects of these case studies, some other regions with no hydrogen sulfide content were selected as control. In all cases water samples were taken carefully for chemical analysis in the laboratory. Besides, mineral compositions were characterised in some cases for better evaluation. In order to give a thorough prospect of hydrogen sulfide production, a geochemical model was prepared. In situ engineering geological conditions, especially pressure and temperature, were assigned in the model to investigate the possibility of H2S generation using PHREEQC software. The results of modelling revealed that although many similarities existed between mineral compositions of the cases, certain formations were particularly prone to hydrogen sulfide generation. For better evaluation, important exchangeable cation ratios such as potassium/sodium, calcium/magnesium and ion proportions like sulfate and chloride were calculated as trends of the formations. As expected, the model could successfully monitor a higher ratio of SO42- and Cl- in potential H2S generator formations. Wide variation in percentage of HCO3- was considered as a secondary observatory parameter for better estimation. In addition, it was noticed that higher anion content created an environment ready to absorb any cations and this makes H2S generation easier. Finally, using correlations between predictors and estimators for low depth and deep samples defined the degree of effectiveness for every sample.

Sep 26, 2011

By A R. McKinnon

The recently opened Hera Au-Pb-Zn-Ag mine in central New South Wales has provided an ideal opportunity to demonstrate the calculation of sulfide ore mineralogy using normative methods. Normative mineralogy applies a set of sequential rules based on the species likely to be present to assign the chemical components of a sample to their respective mineral components. The dominant sulfide mineral assemblage present at Hera is galena, iron-bearing sphalerite, chalcopyrite, pyrrhotite and pyrite. A normative technique for estimating the relative abundance of each of these species from drill hole, grade control and metallurgical assay data sets has been developed. This includes a process for deriving a gangue iron value and differentiating pyrrhotite from pyrite using sulfur/iron ratios. A calculated total sulfide volume value has been utilised at the mine to improve interpretation of lode boundaries. Normative drill hole values have also been used for domaining within the orebody, with large scale mineralogical trends evident. Dry bulk density (BD) values calculated using a normative species-weighted method show good correlation with measured BD values (R2 = 0.895) and are a significant improvement on the Pb+Zn+Cu regression method (R2 = 0.646) previously used. Application of these calculations to identify errors in assay databases is demonstrated, with specific reference to the data set for the nearby Nymagee copper deposit. Validation of block model grades is also explored and a method to improve resource estimates using direct normative mineral interpolation is proposed. The integration of the normative data into the production and metallurgical data sets at Hera is described and the relationship of the normative minerals to other economic elements such as gold and silver is discussed.CITATION:McKinnon, A R, 2017. Application of normative ore mineralogy to geological and metallurgical data sets at the Hera Au-Pb-Zn-Ag mine, New South Wales, Australia, in Proceedings Tenth International Mining Geology Conference 2017, pp 63–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By F K. Altuntov

The study presented in this paper is based on the Kiirunavaara underground mine located in the northern part of Sweden. The deposit is mined using the sublevel caving (SLC) mining method. This paper briefly reviews the alternative SLC layouts, as well as presents challenges for the application. In Kiirunavaara currently, the traditional SLC design is employed, however, continuous improvement of material transportation systems used in mines generates a need for investigation of the current and future production area layouts in sublevel caving mines. When identifying the potential benefits of the alternative production area layouts, the production targets and effects must be further investigated to understand the benefits and potential effects. In this study, several different layouts have been investigated and evaluated. The designs include different development configurations and orepass infrastructure moved further away from the orebody and still require further investigation.

Mar 29, 2023

By C Cavern, G Jacobs, F Durufle, L Ameglio

Airborne geophysics and geomatics is at a crossroads as to whether it remains a viable mapping tool, both technically and commercially, and broadens its potential for new applications (eg environmental monitoring, civil engineering and precision farming). The use of small and stable multisensor aerial platforms to conduct highly flexible surveys flown at a low/reasonable cost of operation is a recurrent wish of many stakeholders in the natural resources exploration and mining industry. Through its Fly Light Airborne Geophysics research program, EXIGE and partners have pushed the development and testing of two new airborne carriers with unique capabilities for geo-surveys: GyroLAG’s gyrocopter and Infotron’s unmanned aerial vehicle (UAV). These carriers are the next generation of versatile and innovative aerial vehicles for remote sensing and monitoring. They are rotary, smart tailored, ultra-high resolution manned (gyrocopter) or autonomous (UAV) airborne platforms that combine the merits of dense data sampling, accurate position location, very low clearance above ground or sea level, slow speed, interchangeable and combined multiple geo-sensors, automatic data quality control and real-time quality assurance. They also have the benefits of being highly efficient, cost-effective, commercially attractive, safe, reliable and easy to deploy and operate. Their technical specifications and multiple advantages compared to traditional aircraft and/or ground crews are presented in this paper. An overview of various geo-sensors (magnetic, gamma-spectrometry, visual, near-infrared and LiDAR) carried on-board is also provided.CITATION:Ameglio, L, Durufle, F, Jacobs, G and Cavern, C, 2015. Light airborne platforms for monitoring mines and minerals, in Proceedings Third International Future Mining Conference, pp 11–20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By I Grewal, M Lundt

Dense medium separation (DMS) is one of several preconcentration methods used for early waste rejection from run-of-mine ores at relatively coarse particle sizes prior to additional milling and beneficiation. DMS has been used extensively in the coal, diamonds, mineral sands, base metals and iron ore industries to produce either a final product or as a preconcentration step. Laboratory scale and pilot test work at the Met-Solve laboratory in Canada has demonstrated successful separation and upgrading of other minerals such as lead, zinc, copper and lithium based ores using DMS.This paper reviews historical dense media systems, results from the pilot-scale multi-stage DMS Separator “Condor” system, as well as production plants and associated laboratory heavy liquid separation (HLS) test work on various minerals. The mineral systems tested included a lithium bearing ore and a fluorspar ore. Other minerals were tested but are not reported in this paper.Pilot plant test work on a fluorspar ore showed that 41.6% of the mass could be rejected to the tailings stream while 95.3% of the CaF2 was recoverable to the product stream. On a spodumene sample that was tested, it was possible to reject 55% of the mass to tailings while recovering over 90% of the lithium.In recent market conditions and with the decreasing grades in existing ores, preconcentration should be a consideration to maximise the value of certain operations.CITATION:Lundt, M and Grewal, I, 2017. Dense media separation – a valuable process for preconcentration, in Proceedings MetPlant 2017, pp 122–130 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By B Lance, D O’Brien

The Hidden Secret ore body is located within the Mt Charlotte underground mining system in Kalgoorlie, Western Australia. Mineralisation of the Hidden Secret ore body is lode style and therefore differs from the typical economical mineralisation mined at Mt Charlotte and consequently demanded a novel approach to the mining methodology. The ore body is lens like in shape, extending 200m along strike, 210m vertically, and dipping at 55 degrees. The lode width varies from 1.5m at the extremities to over 22m in the central zone of the ore body. Average grade is 3.4 Au grams per tonne. The initial mining methodology was Modified Avoca utilising Longhole Open Stoping with pillars, in a bottom up stoping sequence. However, as Hidden Secret became better defined and wider than initially modelled, it was identified that a high portion of gold would remain in the pillars and other mining concerns emerged such as remote backfilling large open voids and potentially unsafe vertical standoff distances between levels and wide open stopes. A re-evaluation of this method was undertaken and a new approach adapting a variation of Avoca methodology was identified to remove the rib pillars and replace them with a sill pillar separating the 4 levels into 2 distinct blocks. This new approach provided an immediate advantage by removing the bogger backfilling activity from the same level of the active stope front, enabling stope drilling and prepping to occur during the backfilling cycle. Bogging productivity has also improved as the fired ore is funnelled to the draw point by the backfill rill, significantly reducing the requirement for remote bogging thus improving bogging productivity. This mining method is currently in progress in the first of the two mining blocks and is on track to realise the targeted recovery of 7,700 ounces from the rib pillars.

Mar 15, 2021

By G K. N Subasinghe

Metallurgists operating Knelson Concentrators (KC) often rely on manufacturerÆs recommendations for selecting operating parameters, such as fluidising water flow rate and cycle time. Recent studies have shown that these parameters are not only dependent on the machine parameters but also on the feed characteristics, such as size distribution of the gold and gangue particles and the composition of its constituent minerals. It is known that a particle entering a KC initially traverses a circular path within the bowl. For a particle to maintain a given orbit, the required centripetal force must be supplied by external means. It has been argued that this centripetal force, which is dependent on the mass of the particle, its radial position and the rotational speed of the bowl, is provided by the fluid drag force created by inwardly moving fluidising water and the BagnoldÆs force created by the particle/particle collisions. Depending on the fluidising water flow rate, one of two situations can occur where the porosity of the bed increases or decreases, which influences the amount of material retained within the bowl. The amount of material of a given size and density retained in the bowl is thus dependent on the extent of the centripetal force provided. Based on the above concept, a criterion that can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It may also be construed that this criterion demarcates the transition of the bed from a packed-bed state to a fluidised state. By identifying the transition values for the different constituent mineral particles in the feed, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. In addition, the kinetics of gangue displacement by incoming heavy mineral particles were also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build-up of heavy mineral reaches a maximum. A model has been proposed to predict the optimal batch cycle time for a KC in terms of the feed characteristics and machine operating parameters.

Jan 1, 2006

By M T. Nguyen, S Vink, M Ziemski

On any given mine site the water system is contingent upon its initial design. Through time the initial design is adjusted by a myriad of water management options in order to improve water system performance or to adapt to a new production capacity or method at the mine site. These options generally do not comprehensively consider energy requirements, so it is unlikely that any given mine water system will be optimised in terms of both water and energy uses. Thus this may simply shift constraints of efficiency of one resource dimension, water, to another, energy. As a result, changes in water systems would cause more energy-related issues to mining companies. For example, the companies would have an increase in operational cost and/or pay more for carbon tax with changes in their water system. Therefore, in order to avoid undesirable and potential unforseen energy and infrastructure issues in a mine life cycle, it is essential to select suitable water management options for a mine considering both water and energy resources simultaneously.Considering water and energy criteria in evaluating water management options consists of net water volume availability, net operational energy demand and net water replacement energy demand. Ideal water management options should be high in water volume availability but low in both operational energy demand and water replacement energy demand. A water option would also be favourable if it has low potential of causing adverse environmental impacts such as lowering groundwater tables due to groundwater withdrawal, or elevating saline constituents in surface waters when reusing brine for dust suppression. However, these environmental impacts are not considered in this analysis.This article presents a graphical method to assess mine water management options, based on these three criteria. The proposed method to assist in screening mine water management options includes two main steps:1. categorise water management options into prioritised groups2. rank the options within each prioritised group.The method is applied to a gold mine and presented in this article as a worked example. CITATION:Nguyen, M T, Vink, S and Ziemski, M, 2013. Selection of mine water management options considering both water and energy impacts, in Proceedings Water in Mining 2013 , pp 29-34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By G Wyartt

In the Pilbara region of Western Australia, an iron ore mine is undertaking a high wall cut-back to improve stability and allow access to deeper ore deposits. Several sections of the wall have been classified low factor-of-safety due to unstable localised geology, and therefore an engineered approach to vibration critical blasting was required. The use of electronic detonators allowed multiple signature (seed) holes to be incorporated into a production blast adjacent to the low factor-of-safety area, therefore providing baseline vibration data to be used for future modelling with the added advantage of eliminating unnecessary pit closure downtime typically associated with a signature hole program. All subsequent blast patterns also incorporated multiple signature holes to provide additional data and allow continual updating – and therefore improved accuracy - of the blast prediction model. Electronic detonators and blast initiation systems were combined with advanced blast vibration modelling software to produce optimal timing sequences with predictable vibration outcomes. Although minimising vibration was the primary focus, blasting induced frequency was also a concern for the project team and therefore initiation sequencing was optimised to also avoid undesirable frequencies. Minor variations in ground factors (vibration transmission and attenuation) were noted, and therefore justified the inclusion of regular signature holes which allowed continual vibration model updates. Blasting results produced vibration and frequency measurements within allowable limits and closely resembled the predictive model. These positive results were achievable through the combination of electronic detonators, advanced modelling software and good onsite practices by engineering and on-bench teams alike. This project will remain ongoing as the pit progresses to deeper benches, and therefore the same methodology will be applied; quality and continual data collection, the use of electronic detonators, and optimisation via advanced vibration and frequency modelling software. CITATION:Wyartt, G, 2018. Vibration control blasting for low stability final walls, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 504–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By A Vakili, F Harvey, H Greaves

Mine seismicity is one of the most difficult geotechnical risks to manage in seismically active mines. There are currently some established empirical and statistical methods that provide quantitative measures for seismic hazard assessment in operating mines. However, these methods are mostly suitable for quantifying the current or historical seismic hazard and often cannot be directly used to forecast the future hazards. Numerical modelling is the only analytical tool that can capture the level of complexities required for a meaningful analysis of mine seismicity and therefore to facilitate a reliable forecast of future hazards. However, there is currently no widely accepted and established guideline and methodology for analysing and forecasting mine seismicity using numerical modelling. This paper first provides a background on previous published studies on this subject and then outlines the key aspects that can affect the reliability of the forecasting for mine seismicity. These aspects include a) processing of historical seismic data, b) selection of suitable numerical modelling approach, c) Post-processing and interpretation of the model outputs. A case study is then presented for the Gwalia Deeps Mine where a new framework was developed to forecast future mine seismicity. High-quality seismic data for a period of five years was used for back-analysis and comparisons with the numerical modelling outputs. After development of the method, the future seismicity was forecast for the next 12 months and the actual seismicity was monitored against the forecast during this period. Results of this study shows promising potential for the proposed framework to be applied more routinely and at other mine sites. However, more validations are required at Gwalia Deeps mine as the mine proceeds to deeper levels. In addition, the method needs more improvements and should be tested and validated at other mining operations before it can be established as a proven method. CITATION:Vakili, A, Harvey, F and Greaves, H, 2018. Forecasting mine seismicity – towards a more established methodology, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 207–222 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By C Laming, S Staude, D Hammond, S Sheppard, J Griffith, S Stanfield, S Marriott

Long Operations is located on the eastern slope of the Kambalda Dome in Western Australia. Kambalda hosts nickel deposits that are modelled to have formed from an exsolving sulfide melt from a parental komatiite melt. The nickel deposit model predicts a stratigraphical relationship where massive Fe-Ni-Cu-sulfides are deposited in troughs at the base of komatiite channels. The basal contact of the sulfides is generally tholeiitic basalt. The Kambalda geological sequence form a dome structure with a granodioritic core and have undergone tectonic and metamorphic overprinting, resulting in the formation of upper greenschist to lower amphibolite-facies units.On the basalt-ultramafic contact, within the Long Operations, there are two separate channels hosting seven different orebodies. The Moran orebody is the most undisturbed orebody at Long Operations, with many primary magmatic textures preserved, making it ideal for studies to improve the existing nickel sulfide formation model. Detailed exploration and production infill drilling and systematic sampling indicates consistent nickel tenor variations over the entire Moran orebody. This was also observed in other deposits in Western Australia and was explained as metamorphic variations. Similar variations are observed with some trace elements that cannot be explained by metamorphic overprint but with gravitational segregation in the liquid sulfide. Other more complex trace element patterns (eg Cr) require additional explanations and are partly originated from incorporation of underlain basalt and sediment and partly from gravitational segregation.From a mining perspective, the Moran orebody can be used as an example of modern high-speed mining, but at the same time preserving samples for the future and allowing knowledge from the geological context and geochemical signatures to improve future exploration.CITATION:Staude, S, Marriott, S, Griffith, J, Laming, C, Hammond, D, Stanfield, S and Sheppard, S, 2014. Improvement of existing ore-forming models due to systematic sampling during mining – an example from Kambalda, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 341–348 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By P B. Hills, R J. Walton

Geotechnical instrumentation has been implemented as a key step for monitoring and optimising an engineered mine design for managing seismicity at the Beaconsfield Gold Mine. Measurements of displacement, stress change, ground control element load and seismic response of the rock mass allow for back analysis and calibration of critical parameters for feedback into the engineering design loop. Instrument clusters are installed in strategic locations prior to the commencement of stoping in order to determine the nature of the response of the rock mass to stoping. A selection of instruments including instrumented cable bolts and rod extensometers, resistance wire extensometers, hollow inclusion stress cells, vibrating wire stress meters and resistance wire extensometers are used to gather data through a data logging system. The rate at which data is recorded is adjusted to provide more information during periods of anticipated rapid change such as around stope firings or during periods of high seismic activity, and less information during periods of anticipated quiescence. The twofold purpose of the instrumentation is to calibrate the numerical modelling output which forms the basis of the engineered mine design, and to provide an alert mechanism where the behaviour of the rock mass is not what was anticipated, or where the impact of that behaviour may compromise the integrity of the engineered ground control system. The paper describes the location of instrument clusters with respect to stoping, the type of instruments employed and the method of data acquisition. It provides examples of results obtained and illustrates the way in which that information is used to optimise the mine design and manage seismicity.

Jan 1, 2008

By A Jankovic, D David, P Payne

Although the majority of current steel production is supported by iron ore sourced from high-grade haematite deposits, the long-term growing demand for steel has led to higher raw material prices and opened the way for many new magnetite deposits to also be developed. There is a rich and long history of magnetite ore processing in Western countries, including large operations such as Cleveland Cliffs in the USA and LKAB in Sweden, as well as smaller operations like Savage River in Tasmania. The challenge for virtually all magnetite operations is to minimise operating costs, which is dominated by the cost of power required to fine grind the ore in order to achieve acceptable concentrate iron grade together with low impurity content. This remains the case today and will be even more important in the future when a carbon tax is expected to become a significant addition to the operating costs for magnetite deposits. Historically, the lowest operating cost was achieved by multistage fully autogenous grinding with integrated magnetic separation steps between the stages. The major benefit of fully autogenous grinding is the elimination of steel grinding media costs and the need to discriminate between steel and magnetite in coarse magnetic separation. The separation step between grinding stages progressively reduces the amount of material to be ground. Application of more efficient grinding technologies developed in the last 20 years, including high pressure grinding rolls (HPGR) for fine crushing and stirred milling for fine grinding, has provided opportunities to further reduce the operating costs associated with comminution. Both technologies are already implemented in some magnetite processing operations, although in limited capacity. The results of a theoretical option study for high capacity processing of a hard, fine-grained silica-rich magnetite ore is presented in this paper, with the emphasis on comminution circuit options. Several circuit options are ranked based on a net present value analysis incorporating an estimate of carbon tax added in the operating cost. The study demonstrates the significant advantages of applying more efficient autogenous grinding technologies.

Jan 1, 2009

By Reichman J. P

Extensive use is made of a small scale computer (IBM 1130), in the calculations of ore reserves for Western Mining Corporation's nickel mine at Kambalda, W.A. All surface drilling data such as assays, density and location information, are stored on disk files at the Company's Technical Computing Centre at Perth, W.A. The computer is used to search through the data, select significant ore intersections, calculate the area of influence of each intersection and perform the necessary calculations to arrive at an estimate of the ore reserve. Comparing the computer-assisted ore reserve calculation with an entirely manual operation, it is estimated that a saving of 40 percent in time is achieved together with

Jan 1, 1973