Search Documents

By T Suwa, S Ishida, J Xue, S Fuchida, H Shimada, Y Aoki, C Tokoro

Pyrite depression with prolonged pre-conditioning treatment in high salinity water has attracted much of researchers’ interest in recent years considering the increased utilisation of multiple stage flotation, closed water circuits, clay minerals, and sea water in flotation plants. In this study, the role of calcium (Ca)/magnesium (Mg) precipitates in stabilising the dissociative ferric hydroxy-xanthate (FHX), and its effect on modifying the balance of hydrophobic/hydrophilic species on the pyrite surface were primarily investigated. The total amount of extractable Fe-bearing species on pyrite concentrates and tailings after floatability test was quantitively determined using ethylenediaminetetraacetic acid (EDTA) extraction tests combined with inductively coupled plasma optical emission spectroscopy (ICP-OES). A more evident accumulation of extracted-Fe in pyrite concentrates rather than it in pyrite tailings was observed at both pH 9 and 10.5 when pyrite was pre-conditioned in Ca/Mg-bearing solutions for 360 min. Fourier transform infrared (FTIR) spectroscopy showed the main xanthate derivatives changed from di-xanthogen (1155 cm-1 ) to FHX (1167 cm-1 ) on the oxidised pyrite samples that were preconditioned in Ca/Mg-bearing solutions. Scanning electron microscopy-energy dispersive spectrometry (SEM-EDS) suggested the preferential accumulation of FHX upon secondary Ca/Mg-bearing precipitates as reflected by the higher Fe/S ratio together with the decrease of O element herein after xanthate conditioning. Although the hydrophilic secondary Ca/Mg/Fe-bearing minerals on the pyrite surface generally deteriorate pyrite’s floatability, the upper section of these secondary hydrophilic aggregates is partially covered by FHX alongside with further multilayer-adsorbed di-xanthogen. The precipitated Ca/Mg-bearing precipitates promotes the immobilisation of dissociated FHX derived from the reaction among iron oxyhydroxides and xanthate anions upon the localised secondary Ca/Mg/Fe-bearing minerals via acid–base complexation. Therefore, this phenomenon alleviates the hydrophilic modification of secondary Ca/Mg/Fe-bearing minerals to pyrite considering the immobilised FHX upon localised precipitates shows a slight hydrophobicity, and meanwhile, the upper FHX benefits the multilayer adsorption of di-xanthogen via the interaction among their inner hydrophobic alkyl chains.

Aug 24, 2022

By T Wang, D Wang

Photogrammetry-based techniques supported by traditional mapping tools are more frequently used for open pit geotechnical mapping. It fundamentally involves the collection of geological, structural and rock mass data from pit batters when safe to do so. These are essential components for refining and implementing continuous improvements to geotechnical models. The geotechnical model is used to review bench performance, optimise geotechnical design parameters, interpretation and analysis of pit slope stability. This paper is a case study of implementing different pit mapping methods at Mount Carlton gold mine, North Queensland. It critically reviews the tools required, including the Brunton compass, mobile application Clino, geotechnical data mapping software CloudCompare (2015) and Sirovision software. The review compares the image precision, structural measurements and data analysis. The review also underlines mine site management philosophy for safe geotechnical data collection to identify in-pit geotechnical hazards and the mitigation of potential slope instability. Sirovision is a remote sensing system for site geology mapping and interpreting geotechnical characteristics of exposed mining faces. The system utilises off-the-shelf digital SLR cameras to capture stereo photographs of the rock face and uses the latest image processing technology to generate accurate 3D models. These 3D models are digitally analysed using computational geometry to extract unbiased and accurate geological and geotechnical data. CloudCompare processes high accuracy 3D dense cloud rock surfaces reconstructed with photogrammetry software to extract the geological planes using the FACET or Compass plugins. The major discontinuity sets can be observed and the orientation (dip/dip direction) obtained from the algorithm is accurate and reliable for geotechnical assessment, including kinematic and rock slope stability analysis.

Nov 29, 2022

By G Harbort, D Zoetbrood

"The Phu Kham copper-gold operation in the Laos People’s Democratic Republic (PDR) is owned and operated by Phu Bia Mining Limited. PanAust Limited holds a 90 per cent interest in Phu Bia Mining Limited, with the remaining ten per cent held by the Laos PDR Government.The original 12 Mt/a copper-gold concentrator at Phu Kham commenced production in April 2008. An incremental improvement program resulted in a number of circuit changes being incorporated by 2011, including conversion of conditioning tanks to flotation cells and the installation of a Jameson Cell cleaner scalper. In 2012 the Phu Kham Upgrade Project was commissioned to increase throughput to 18 Mt/a. In April, 2013 the Phu Kham Increased Recovery Project was commissioned to maximise performance by debottlenecking the plant IsaMill™ regrind and cleaning capacity.With the variable mineralogy of Phu Kham ore, control of the c concentrate regrind circuit is essential in terms of achieving effective liberation to maintain concentrator performance. On a routine basis laboratory regrind signature plot data is compared with daily surveys of the operational IsaMills™. More extensive surveys are also conducted to determine size distribution on a mineralogical basis and the effect of fine regrinding on pulp electrochemistry and flotation performance. This paper provides a review of the operating performance of the Phu Kham IsaMills™ with regard to power draw, feed and product size distribution, feed per cent solids, mineralogy and pulp electrochemistry. Operating performance is compared with the IsaMill™ signature plot test for predicting performance.Citation:Harbort, G, Zoetbrood, D and McNab, B, 2016. Operating Performance of the Phu Kham IsaMill™, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 39–50 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By P C. J Blackney, I M. Glacken

Spotted Quoll is a massive sulfide nickel deposit located in the Forrestania greenstone belt in the Archaean Yilgarn block in Western Australia. Discovered in October 2007, mining has progressed from open pit to underground and currently uses longhole open stoping with paste fill as the primary stoping method. Immediately prior to 2019, the Mineral Resource estimate (MRE) was defined by a single grade domain of nickel greater than or equal to 0.8 per cent, irrespective of the host lithology, a legacy of the original ore wireframe being built using explicit methods. While a number of obvious structural offsets were honoured in this nickel grade domain, only one modelled fault was used to undertake domaining of arsenic. From 2019 onwards, implicit modelling in Leapfrog Geo™ was used to construct a mine-scale geological model, which triggered the definition of a high-grade core of massive/matrix nickel sulfides surrounded by a low-grade halo of stringer/disseminated nickel sulfides in the surrounding rock. As part of the evolution of the geological model and with the aid of Seequent Central™ to allow collaboration between site-based mine geologists, Perth-based resource geologists and Melbourne-based consultants, a detailed review of the structural mapping was carried out as additional information from underground development became available. This allowed numerous faults and shears to be identified – particularly in the lower half of the mine. These were used to define further structural domains and to refine the understanding of the nickel and arsenic grade distributions in the mineralised envelope. The increased definition to the domains provided by the geological model resulted in a significant improvement in the accuracy of the Mineral Resource estimate, as measured by reconciliation using voids of the mined stopes determined from the cavity monitoring survey (CMS).

Mar 22, 2022

By I D. Gregson, A S. Garcia, K M. MacAndrew

The design work undertaken by Rock Mechanics Technology (now part of Golder Associates (Golder)) has played a major part in successfully establishing mechanised room and pillar working in Indian coalmines, both for the development of new districts and for the re-establishment of old districts prior to pillar extraction on panel retreat.Golder has used appropriate design of pillars, extraction sequences and final snook sizes to minimise ground control risks during pillar extraction. Where the strata will not cave reliably, partial extraction systems leaving either a crush pillar or a substantial yield pillar have been adopted.Remote monitoring of selected pillars during the extraction process using stress cells, extensometry and convergence measurements provides confirmation of pillar behaviour and verification of designs.A new telltale device, giving a visible warning of impending caving, is now installed at all Indian pillar extraction sites and is proving very successful.CITATION:MacAndrew, K M, Garcia, A S and Gregson, I D, 2014. Coalmine pillar design and performance during mechanised pillar extraction in India, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 347–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Y Zhang, Z Zhao

The green production of the steelmaking process has urgent requirements for fluorine-free fluxes. In this article, a new solid waste-based slagging flux was applied in the external dephosphorisation test of low silicon hot metal to replace the traditional fluorite-lime dephosphorisation slag. The results showed that under laboratory conditions, the new flux was utilised for smelting low-silicon molten iron with a phosphorus content of 0.10~0.13 wt per cent, the temperature of the molten iron was 1350°C and the slag amount was controlled at 2 per cent. Within ten minutes of smelting, the dephosphorisation rate of the molten iron reached more than 50 per cent. When making slag with new flux, the slag melting time was about 40 seconds and the P2O5 content in the final slag was higher than 8 wt per cent. In the industrial test of a 150 t molten iron ladle, under the same molten iron conditions, an out-of-furnace dephosphorisation test was conducted in the Kambara Reactor (KR) process. The flux material consumption per ton of steel was 8~10 kg. Within 15 minutes of smelting, the dephosphorisation rate of the molten iron was about 30 per cent. During flux slag making, the slag melting time was about three minutes and the P2O5 content in the final slag was higher than 6 wt per cent. This new solid waste-based flux has significant cost advantages and outof- furnace dephosphorisation effects and is expected to become the benchmark for a new generation of fluorine-free steelmaking fluxes.

Aug 21, 2024

By N Schofield

For the sampling of particulate materials in mineral exploration and mining, the fundamental sampling error (FSE) introduced by Gy is a measure of the constitutional heterogeneity of the sample lot and is expressed as the relative standard deviation of subsample grades of a particular mass. The FSE is presently regarded as an important indicator of quality for samples used in resource estimation. Constitutional heterogeneity describes an ideal state of heterogeneity with respect to all constituents of the lot such that the fundamental error among subsamples of a particular mass is minimised.In this paper, the term ‘sampling precision’ used in relation to mineral resource sampling usually refers to a statistic based on the assay results drawn from pairs of separate subsample splits of multiple sample lots. The pairs of splits are extracted after the lots have been prepared by crushing and pulverising to meet specified criteria of grain size and subsample mass. There is presently no generally accepted method of calculating the ‘sampling precision’ from such paired data but some form of the relative standard deviation that is consistent with definition of the FSE is preferred here. The work of Thompson and Howarth in the 1970s on geochemical analytical precision, which has been subjected to extensive examination and criticism by Stanley and Lawie (2007), and that of Francois-Bongarçon since the 1990s forms the background to the discussion in the paper.A significant aspect of the application of Gy’s sampling theory to sampling in gold deposits is the requirement that the fundamental error be maintained at less than ±20 per cent. The most important reason for this is to ensure that the effects of other sampling errors such as the grouping and segregation, and increment delimitation which can cause local and global biases in sampling are kept as small as possible. This paper is focused mainly on the quality of sampling in gold deposits and looks at an alternative to the use of a constant sampling precision applied to a collection of lots with varying average grade. A theoretical model for the FSE based on duplicate sampling is presented and the simulated results of the model are compared to practical outcomes of real duplicate pairs drawn from multiple sample lots. The goal of the work is to present a more informative analysis of duplicate sample data from multiple lots which may allow a more informed view of the potential for bias generating errors during sample preparation and processing.

Aug 22, 2011

A forecast of energy demand in the non-commu- nist world to the year 1990 is presented with com- ments on the expected effectiveness of conservation efforts in achieving more efficient utilization of energy. A forecast of energy supply for the same period is presented showing the contribution of oil, gas, hydropower, coal, and nuclear fuels, with brief comments on the factors constraining the rate of growth of non-oil energy supplies. The role of `synthetic fuels', i.e. liquid or gaseous fuels produced from coal, oil shale, and tar sands, is reviewed with brief discussion of factors affecting the development of this industry. In somewhat greater details, the growth of demand for oil by geographic regions is analyzed. Particular attention is directed to the source of the oil supplies which will be required. The anticipated rate of discovery of new oil reserves is discussed with comments on lead times required in the development of new discoveries in hostile environments such as the Arctic and deep oceans. The continuing importance of oil supplied from countries which are members of the Organization of Petroleum Exporting Countries (OPEC) is illustrated. Oil will continue to be the marginal ('balancing') source of world energy supply throughout the forecast period and although it now appears that oil supplies will be sufficient to balance the energy equation during the 1980s, little flexi- bility will exist to cope with unexpected growth in demand or slippage in supply. Prudent energy re- source management will require major efforts to stimulate conservation and also to stimulate the rapid development of conventional and new forms of energy supplies and changes in energy consump- tion patterns to utilize the new supplies. Because of the long lead times and the massive capital require- ments involved, governmental policies are needed soon which will stimulate conservation and which will encourage businesses to move rapidly to assure the energy supplies the world will require in the 1990s.

Jan 1, 1978

By J-P Franzidis, E V. Manlap

Froth transportation characteristics have a significant impact on the flotation recovery especially in large flotation cells. The probability of an attached particle being recovered into the concentrate depends strongly on the location where it enters the froth phase. A mathematical model for froth transportation in industrial flotation cells was proposed (Zheng et al, 2004). The model has been tested on the experimental data obtained from testwork conducted at the Western Metals Hellyer lead/zinc concentrator. The results show that the model fits the experimental data well, especially when the froth is well developed (ie for a deep froth). The model fitting can be significantly improved by incorporating an air dispersion factor. However, the models encounter some limitation, ie inconsistent prediction at different froth heights, due to change in froth viscosity which cannot be modelled at the present time.

Jan 1, 2005

By R Morrison, R Dunn

In many mineral processing operations, the reported production figures for an accounting period may not make the best use of available data. While most of the mathematical approaches, such as check-in/check-out, mass balancing, used in effective metallurgical accounting strategies are well understood, the sources and magnitude of measurement errors generally are not. As part of the æAMIRA P754-Metal Accounting and ReconciliationÆ project, a study was undertaken at the Northparkes copper/gold concentrator near Parkes, New South Wales to examine the data used in their concentrator metallurgical accounting system. This paper summarises the results of a detailed examination of the mass measurement systems around the concentrator as well as the primary sampling system used for grade estimation. The goal of this work was to develop practical techniques to quantify the error (ie both accuracy and precision) of the measured metal accounting information. With this information, statistical confidence levels for this data can then be calculated. If the errors are small, the effect of error in each piece of measured data can then be propagated to other calculated production figures such as recovery and feed grade using a statistical technique called æthe propagation of errorÆ.

Jan 1, 2007

By R Moreby, J Kok, L van den Berg

The high production rates achieved from mass mining methods such as block caving, sublevel caving and longwall mining require large conveyor belts, trucking loops (diesel/electrical) and rail systems for ore handling. However, the ore handling systems used in mass mines introduce a significant amount of heat into the overall ventilation system, which may be problematic at depth or in mines located in hot climates.In particular, the heat load from a conveyor system is not always well understood and consists of various components, including frictional heat from idlers, heat from electrical motors, heat from the drive train and heat from broken rock transported on the conveyor system. This paper presents results from a study that investigated the heat introduced to the ventilation air from a large conveyor system. The conveyor system transports ore with a maximum virgin rock temperature of 41°C from a depth of over 1 km. Air, belt and rock temperatures were measured in the conveyor system to evaluate the distribution of heat loads.CITATION:van den Berg, L, Moreby, R and Kok, J, 2015. Heat load estimation from conveyor systems in mass mines, in Proceedings The Australian Mine Ventilation Conference, pp 63–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By L Lorenzen

The selection of samples for metallurgical test work is generally focused on providing geologically representative samples. One of the major problems experienced with metallurgical test work using drill hole data, is the small sample sets selected for metallurgical testing. Major process and financial decisions are being made from results obtained using snapshot samples. Snapshot samples means that samples are basically selected only by grade and spatial location with the assumption that the rest of the orebody or portion of orebody is similar and will respond metallurgically the same way – ie the assumption is that the mineralogy and lithology are basically the same as the test sample. From the test work, algorithms were usually developed and used to describe throughput and recovery using some explanatory variables including grade (mineral chemistry) and ore hardness. These algorithms were then used in the recovery models to determine tonnes produced and plant throughput. However, the metallurgical parameters are a function of many geological factors including grade, lithology, alteration, mineralogy, spatial relationships and SG. In previous years, the limited mineralogical information available was deemed enough for the metallurgist to make decisions as to how many samples are needed to evaluate the metallurgical performance of the ore during processing, and subsequently the basis for the plant design. If the orebody is consistent and not complex or refractory (thus, relative simple lithology), then only spatial and grade samples will be needed to evaluate the throughput and recovery, so limited mineralogical information may be acceptable. There is now, however, an increasing realisation that the mineralogy and geology change, as do the metallurgical characteristics of the orebody, so limited samples may not be sufficient for effective metallurgical test work.It is the purpose of this paper to discuss the effect correct mineralogical information has on the subsequent metallurgical test work program and process selection using a case study. Factors such as type of rock, rainfall and topography are thought to influence the minerals that ultimately form in various orebodies, with the result that different orebodies often react differently during metallurgical test work programs. It is therefore important to obtain accurate mineralogical and elemental deportment data, which will also indicate where the valuable metal containing minerals are located within the orebody. The better you plan and execute your metallurgical test work program during the early phases, the more accurate the decision-making process will be during the selection phase. Improved integration between geology and metallurgy data gathering (geometallurgy) during early phases will result in more accurate predictions with regard to throughput and recovery during modelling and process. Equipment selection will be considerably simpler in later phases with early planning, with improved mine and process scheduling and subsequent net present value (NPV).

Sep 5, 2011

By F R. M Pires, R M. Carvalho

Supergene processes in banded iron formation (BIF) result in important dissolution, material transport and simultaneous disorder of the residual bands. The rock physical properties such as density, porosity and rheology change during the weathering attack. The itabirite, Paleoproterozoic metamorphic BIF from Quadrilßtero Ferrffero (QF) û Brazil, shows several weathered facies. Strong linking between topographic surface, rock density and iron grade occurs within the weathered zones. This linking is due to partial dissolution of silica and carbonate from itabirite and gravitational rotation and break of the remaining blades, generating kink-like slump structures. The original itabirite density, 3.7 t/m3, decrease at the first leaching steps, until 2.7 t/m3, and increase at the end of the leaching process until 3.6 t/m3. Iron grade increases from 38 per cent to 68 per cent and depressions (sinkhole), subsequently filled by Cenozoic basinal sediments, are developed over the enrichment zones. The formation of important supergene iron ore deposits of QF is intimately related to such a process. Several iron deposits at QF, such as Pico do Itabirito, Fßbrica Nova, Casa de Pedra, Tamanduß, -gua Claras, Cappo Xavier, etc., reveal the aspects related to the proposed evolution, implying that the formational process of the soft iron ores had a regional character. Granular medium model helped in the understanding of the development of the structure and the formation of the deposits. A numerical model has been developed in order to simulate a leaching system in a two-dimensional matrix, composed of two types of materials: leachable and unleachable. Equal volume proportion and vertical banding were considered. Drilling data was used as multipoint attractors to remove leachable matrix nodes.

Jan 1, 2002

By M J. Nugus, J G. McLellan, T G. Blenkinsop

High fluid pressures and deformation have been instrumental in the formation of high-grade gold lodes at the Archaean granite greenstone 12 Moz Sunrise Dam gold deposit in Western Australia. Historically, predicting the location of these lodes has been difficult due to the irregular nature and high-grade nugget characteristics of the deposit. Recent exploration successes and the discovery of the Vogue system have led to an improved knowledge of the deep extents of the mine. This new structural and gold distribution data has enabled a new 3D interpretation of the system and has provided a better insight into the links between deformation, fluid pressure evolution and gold deposition. Here we employ 3D geomechanical and coupled fluid flow modelling to better constrain areas of high strain partitioning, rheological failure and focused fluid flow, which provides a substantially increased predictive capacity for further within-mine exploration. The localisation of deformation in and around the main felsic porphyry and major shallow shear zones provides critical insights into fluid pathways that have contributed to the distribution of fracture networks and ultimately gold deposition during late stage deformation events. Understanding the relationship between deformation events, fluid pressure evolution and the partitioning of strain is paramount in understanding the distribution of gold and for focusing on future target areas.CITATION:McLellan, J G, Blenkinsop, T G and Nugus, M J, 2013. Fluid pressure, geomechanical evolution and predictive targeting of the Sunrise Dam gold deposit, Western Australia, in Proceedings World Gold 2013 , pp 419-426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By N Taylor, P Hewitt

The Northern Beaches Storage Project (NBSP) is part of Sydney Water’s SewerFix™ Program to improve the wastewater system and protect public health and the environment. It was built by the SewerFix Wet Weather Alliance (the Alliance), a partnership between Sydney Water, RPS, MWH, Parsons Brinckerhoff and United Group Infrastructure.The project temporarily stores excess wastewater diverted from the Narrabeen Submain during wet weather. The project considered a below-ground storage facility, which involved constructing a deep tunnel from Brookvale to Fairlight, connecting into the Northside Storage Tunnel and a storage tank, which was subsequently adopted and constructed.The storage tank scheme included a pumping station and inlet and outlet pipes installed by microtunnelling. The storage tank site is in the Brookvale industrial area situated in an area of deep marine sediments overlying Hawkesbury Sandstone at about 30?m below ground. Microtunnelling for the inlet pipe was conducted from a 12?m deep jacking shaft. The jacking shaft and 14?m deep pumping station excavations were carried out from within secant pile earth retaining structures adjacent to existing buildings.Construction activities had the potential to cause settlement of the adjacent buildings. During excavation and microtunnelling the water ingress, adjacent groundwater level and settlement of the adjacent buildings were monitored. The monitoring data was assessed against an action plan, which modified construction activities as required to minimise the risk of damage to buildings from settlements caused by lowering of the groundwater table outside the excavations. The secant pile construction, excavation, microtunnelling and pumping station construction proceeded without incident or damage to adjacent buildings.This paper highlights that tunnel/underground options should be considered during options development, describes the original storage tunnel scheme and presents details of the successful microtunnelling and deep shaft construction adopted on the NBSP.CITATION:Taylor, N and Hewitt, P, 2014. Tunnelling on Northern Beaches Storage Project, Sydney, to improve water quality, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 451–458 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By F Sinaga, E Widijanto

PT Freeport IndonesiaÆs Deep Ore Zone (DOZ) mine is the new underground block caving mine within the East Ertsberg Skarn System (EESS) which started production in mid-2000. The DOZ will produce 25 000 tpd using mechanised block cave mining method and will be the fourth underground mine opened within the EESS deposit. A review of the DOZ extraction bolting design was conducted in November 2000. The aim of this review was to re-evaluate the effectiveness of the current design in relation to bolt length and spacing and to challenge some questions about the technical background of the design. For instance, the influence of the rock condition on the design. To review this bolting design, several books and papers are reviewed and several experienced people have been contacted to give their opinion. The methodology used for this review is:reviewing the technical background of current design; collecting ideas and alternatives; collecting data from books and personal communication and conducting analysis; and conclusion and proposed design.

Jan 1, 2002

By J Langhans, Y Choi, Q Wang, J Y. Baron, P Kondos

Barrick has successfully developed the thiosulfate leaching process to treat sulfidic high preg-robbing ores. The process was developed through rigorous bench test programs and proved in pilot campaigns and demo plant operations. The process uses calcium thiosulfate as a leaching reagent, resin for gold recovery with sulfite/trithionate elution and reverse osmosis as a mean of reagent recovery. The thiosulfate leaching plant is under construction as a brownfield project and the start-up is planned in 2014 at Goldstrike, Nevada, USA, one of BarrickÆs operations.CITATION:Choi, Y, Baron, J Y, Wang, Q, Langhans, J and Kondos, P, 2013. Thiosulfate processing - from lab curiosity to commercial application, in Proceedings World Gold 2013 , pp 45-50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By R Schmitt, Y Ghorbani, I McElroy, N J. Bolin, M Parian

Aitik is a large copper porphyry type deposit located in northern Sweden, currently exploited at an annual rate of approximately 45 Mt. The ore’s exceptionally low head grade of 0.25 per cent Cu and varying degrees of hardness across the entire deposit pose challenges to the two fully autogenous grinding lines, each of which comprises a primary autogenous mill in series with a pebble mill. The variability in ore grindability frequently leads to fluctuations in mill throughput. Within the framework of a geometallurgical approach, the present study investigated the relationships between ore grindability and modal mineralogy. For this purpose, drill core samples from different lithologies were subjected to Boliden AB’s in-house grindability tests. This fully autogenous laboratory-scale test generates a grindability index mainly related to abrasion breakage, which is a significant breakage mechanism within autogenous mills. The test results suggested divergent degrees of grindability within and across the selected rock types. A combination of scanning electron microscopy, X-ray powder diffraction, and X-ray fluorescence analyses was performed for the grinding products and bulk mineral samples. The resulting mineralogical and elemental properties were subsequently correlated to the parameters from the grindability tests. It was shown that the main mineral phases, such as plagioclase, quartz, and micas, correlate well with the grindability indices. Similar correlations were found regarding the sample’s chemical composition, attributable to the main mineral phases. A further inverse correlation was established between the sample’s calculated average Mohs hardness and the grindability indices. Moreover, mineral liberation information provided by scanning electron microscopy was associated with the parameters mentioned earlier. The identified relationships between grindability, modal mineralogy, and element grades may help Boliden develop a predictive throughput model for Aitik based on the mine’s block model.

Aug 24, 2022

By C A. Myburgh, S Craig, K Deb

In focusing on open pit mine scheduling, one of the biggest areas that a mining engineer can add value is in the area of cut-off grade optimisation. It is not atypical to add up to an extra 20 per cent in value by bringing forward higher-grade ore and deferring costs into the future.There are many techniques available to maximise net present value (NPV) when applied to open pit mine scheduling. That in itself raises the question of why so many of these techniques exist. The short answer is that none of these techniques are robust. Every time the problem changes, the algorithms also have to change.Instead of trying to make a problem fit the constraints of an existing technique, there is much to be said for usefully hybridising different approaches. This paper describes an innovative approach where evolutionary algorithms are combined with both local search and linear programming. The goal is maximising NPV through optimisation of cut-off grade policy and extraction sequence for an open pit mine. The cut-off/cut-over grade policy produced caters for multiple processing streams and stockpiles.Finally we demonstrate the quality of the algorithm by comparing some results with a well-known mathematical solution.CITATION:Myburgh, C A, Deb, K and Craig, S, 2014. Applying modern heuristics to maximising net present value through cut-off grade optimisation, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 155–164 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By L Brodie-Hally

In the early-1990s, Tad Golosinski, the former the head of mining department at WASM participated in a review mining engineering courses in Australia. The review team asked various industry executives what subjects they thought graduates needed to be taught. Tad made the comment to me that the more senior executives thought that history and ethics were very important. The outcome was that the mining engineering courses were required to contain at least five per cent content dealing in ethics. The course was to be modified to reflect this. Tad thought at the time the students would think that subjects dealing in history and ethics came from retirees and professionals that were over the hill. So let me talk to you today about ethics.

Jan 1, 2002