Search Documents

By John V. Beall

Monotonous flood planes flanked either side of the road as we drove in the embassy car from the airport to downtown Seoul. We crossed the brown waters of the Hann River, meandering over mud flats. A great, gnarled tree bore beautiful fall colors of gold. "That is a Ginko Tree, the oldest living fossil, probably a hundred million years old;" said Jean W. Pressler. Compared to other cities of the Far East, the traffic in and around Seoul was sedate. Few motorcycles or bicycles, and little superfluous horn tooting. "This is the best season in Korea. We have long beautiful springs and falls," said Pressler, chief of the mining branch of USAID, and he continued with a briefing on the country.

Jan 8, 1969

By G. B. Gould, F. M. Gibson

IN DECEMBER, 1934, the joint Committee on Fuel Values, of the American Institute of Minim and Metallurgical Engineers and the American Society of Mechanical Engineers, submitted a preliminary report, which briefly stated its conclusion that it was not possible to devise any formula for the valuation of coal, based upon the various physical and chemical properties, that would be generally applicable. That report also listed those chemical and physical properties of coal that are generally recognized to have some effect on its use in steam plants, and those physical characteristics of steam plants which affect, in one way or another the relative importance of the properties of coal used in them. Since then, the Committee has considered and discussed in greater detail the interrelationship of the properties of coal and plant characteristics. The conclusions of the Committee are summarized below, with certain recommendations regarding engineering procedure, which will promote the collection of more easily correlated observations with respect to this subject, and thus advance more rapidly the accumulation of data capable of general application.

Jan 1, 1936

A Discussion of the papers of James Gayley, on "The Application of Dry-Air Blast to the Manufacture of Iron" (see Trans., XXXV., 746, 1022, also pp. 315 and 745 of the present volume, and of J. E. Johnson, Jr., on "The Physical Action of the Blast-Furnace," p. 454. Chas. B. Dudley, Altoona, Pa.:—I am not a blast-furnace man, and this always puts me at a disadvantage because I cannot go into the details of the making of iron and steel. I have not the experience, and have to take the statements of other people, so what I say regarding the subject of this paper is not in the sense of an expert. When I first heard of Mr. Gayley's experiments, I said to myself, a I fear they will result in failure, since, apparently, Mr. Gayley has forgotten one chemical fact, namely, that carbon does not combine with oxygen in the absence of mater-vapor." This fact which was so astonishing when it was first brought out some years ago, and which those who are interested may find in the Journal of the Chemical Society of London, for 1885, page 349, and 1894, page 611, led me to think that the drying of the air would be a mistake. The general subject of the influence of water-vapor on chemical action is a large one; but the special point in which we are, for the moment, interested, namely, the influence of water-vapor on the combustion of carbon, was especially treated by Mr. H. B. Baker, in the papers referred to. Apparently, however, as the result of Mr. Gayley's experiments, we are to learn that the amount of moisture still left in the desiccated air is sufficient to secure perfectly satisfactory combustion. In thinking over Mr. Gayley's paper, it occurred to me that there were two alternatives, either of which might be chosen, namely, we might dry the air as Mr. Gayley does, or possibly we might, in a very much easier way, simply saturate the air at a constant temperature, and thus get uniform working and

Jan 1, 1906

By P. J. Conners, H. Colijn

Belt conveyors have proven themselves for many years as a dependable and low cost method of moving bulk materials at high flow rates. The success of a belt conveyor system greatly depends on the initial loading of the material on the belt. If the material is loaded on the belt at the center, at the same speed and without impact, then about 90% of all belt conveyor problems would disappear. Proper belt loading is primarily determined by the engineering and design of the conveyor transfer point. Some general design criteria required for proper transfer of materials from one conveyor to another are established and discussed. Specific attention is given to loading chutes and skirting.

Jan 1, 1973

By K. Reinhardt

The idea of burning blast-furnace gases directly in gas-engines, instead of under steam-boilers, as had previously been done, was first put into practice barely ten years ago, almost simultaneously in Great Britain, Germany and Belgium. The pioneers of this movement made their first experiments with small engines. After these experiments had given satisfactory results, and it had been shown that the thermal value of the poor blast-furnace gases, in spite of defective scrubbing, could with safety be directly transformed into mechanical work in the gas-engine, there very soon arose a considerable demand for gas-engines of large power, similar to the large steam-engines employed in metallurgical works. In face of these sudden requirements, the gas-engine builders were placed in a difficult position; for up to that time the gas-motor was considered as suitable for small engines only, and it was generally believed that the limit of size had been attained with 100 to 150 effective h.p. in a single cylinder. Manufacturers of gas-motors, however, did not underrate the advantages offered by this new field for their manufactures, and it so happened that in Germany the Berlin-Anhaltische Masch-inenbau-Gesellschaft, of Dessau, was the first to undertake the construction of a 600-h.p. two-cycle gas-engine, with two cylinders of the Oechelhauser-Junkers type, for the Hoerder Mining & Smelting Company. The engine was started in 1898, and, with a few improvements and alterations, is still working satisfactorily. This engine worked with astonishingly high effciency, considering the period. The builders were therefore

Jan 1, 1907

E. E. Russell Tratman, New York City (communication to the Secretary): Mr. Glenn's paper brings up again the question of the part played by coal-dust in colliery-explosions. In the discussion of Sir Frederick Abel's paper on " Accidents in Mines," read before the Institution of Civil Engineers,? much was said about the dangerous properties of coal-dust, and several instances were given of the successful use of a spray of water, water and compressed air, or exhaust-steam from an engine, to keep the mine SUEciently damp to prevent the formation of dust clouds. Methods of preventing shots from blowing out; of using water cartridges to prevent flame ; and of using lime cartridges, wedges and other means of breaking down the coal were also discussed. Mr. Emerson Bainbridge referred to the explosive termed " roburite " (ammonium nitrate and

Jan 1, 1895

By H. W. Becker, C. C. Frye, A. V. Degau, A. Masuda

Natural gas containing 25.65 per cent hydrogen sulfide and 4.75 per cent carbon dioxicle is gathered frorn eight \veih arid tratzsporrcd 26 miles at a flow rate of 160 MMcf/D and at operating pressures of frotrl 1,200 to 1,800 psig. Dry desiccant dehydrators at each wellsite tnaintaitz the dew point of the gas below 17F. Telemetering facililies permit control of field operations from a central instrunlent console. Corrosion control ineasures, design coilsiderations and material specifications pertainitz to these specia1 conditions are cliscussed. INTRODUCTION Natural gas containing 25.65 per cent H2S and 4.75 pcr cent CO, is produced from the Pine Creek field, Alta. It is dehydrated at wellheads, gathered at 2.200 psig and transported 26 miles to the Windfall field where it is delivered to the inlet of injection compressors at 1,800 psig. The daily average volume of gas transported is 160 MMcf. The project is believed to be unique in its combination of percentage of hydrogen sulfide, operating pressure and transportation distance. This paper describes the project and presents details of some of the design features, corrosion control program and centralized automatic operational control. The Pine Creek field project is one phase of a joint operation of two fields—thc other being the Windfall field. The two fields lie about 30 miles north of Edson, Alta. and 20 miles west of Whitecourt, Alta., respectively, as shown on the map (Fig. 1). They are owned by the same interests and operated according to a plan for maximum economic recovery of products. The Windfall Leduc D-3 reservoir contains a rich condensate-bearing gas containing 15.5 per cent HIS. The gas from the Pine Creek field contains only very small quantities of butane and heavier products. The Windfall reservoir is being cycled to obtain maximum condensate recovery using gas from the Pine Creek field as the displacing fluid, while producing the residue sales gas for both fields from the Windfall field. The Pine Creek field development and gas-gathering facilities are shown on the map (Fig. 2). The producing formation is the Leduc D-3 reef at a depth of 11,300 ft. The original reservoir pressure was 4,590 psia at 7,400 ft subsea and the temperature is 245F. Eight wells are equippcd with dry desiccant dehydrators with the following capacity ratings: three at 35 MMcf/D; three at 20 MMcf/D; and two at 10 MMcf/D. WELLHEAD EQUIPMENT Dry desiccant dehydrators were designed to reduce the water content of the saturated wellhead stream to 2.5 lb of water/MMcf at 2,000 psig. This specification was necessary to prevent hydrates and corrosion forming in the pipeline which will operate at temperatures as low as 20F. A typical flow diagram is shown in Fig. 3, and Fig. 4 is a photograph of one of the wellhead installations. Some of the design details given below are subject to modification in the field. The well-stream flowing temperatures range from 135 to 170F. Wellhead flowing pressures up to 3,200 psig are reduced to the dehydrator-operating pressure of about 2,100 psig by throttling through a pressure control valve. The gas is then passed through an aerial cooler where its temperature is reduced to 105F. thus removing over half

By H. Morgolin, M. A. Greenfield, P. A. Farrar

In attempts to correlate mechanical properties with microstructure, it is desirable to determine the effect of ß grain size. Determination of 6 grain size is not a problem where a has precipitated at ß grain boundaries. However, in alloys which have been processed to produce an equiaxed a +ß structure the ß grain size is difficult to determine because ß grain boundaries do not etch. The ß grain size can sometimes be laboriously determined by searching for grains which have some a! outlining the 6 grains. This difficulty of ß grain size determination in equiaxed a + ß alloys can be overcome by heating below the ß transus temperature for a short time and water quenching. Fig. 1 shows the starting equiaxed a + ß structure of the Ti-5.25A1-5.5V-0.9Fe-0.5Cu alloy used in this investigation, and Fig. 2 shows the microstructure of the same sample water-quenched after heating 1 min at 1675"F, which is 25°F below the 0 transus. The heavily etched microstructure consists of some equiaxed a! in a structure showing considerable amounts of transformed ß. The ß grain

Jan 1, 1969

By George Otis Smith

A PHILOSOPHER has pointed out that inventive genius, in substituting mechanical power for human brawn, leaves' man the intellectual factor in the industrial life. "Almost human" is the description sometimes applied to the automatic machine, yet the true characteristic of the perfect machine is its unquestioning obedience. "Its not to reason why." The human operator, not the mechanism of gears and levers, has freedom of choice: he wills; the machine obeys: There map be a grinding monotony, a tiring rhythm, that passes from machine to man, but the responsibility resides in the man. In no proper sense call the machine worker be called the slave: whether he guides an electric shovel or tends a group of automatic 1athes.in the machine shop.

Jan 1, 1930

An index covering the papers presented at the 19 Open Hearth Conferences from the first meeting at Pittsburgh, April 15 and 16, 1925, through the most recent meeting in Detroit, April 16 and 17, 1936, the reports of the meetings and the discussions that took place has been published, accompanied by a list of the papers presented, grouped by subject matter and a list of books of interest to open hearth men The list below gives the Open Hearth Conference meetings in chronological order and the symbols used to designate them in the index SYMBOL MEETINGS P25 Pittsburgh, April 15 and 16, 1925 C125 Cleveland, Oct 13 to 15, 1925 Ch26 Chicago, April 12 and 13, 1926 P26 Pittsburgh, October, 1926 B27 Buffalo, May 3 to 5, 1927 D27 Detroit, Nov 2 and 3, 1927 Y28 Youngstown, May 3 and 4, 1928 P28 Pittsburgh, Nov 15 and 16, 1928 C129 Cleveland, May 16 and 17, 1929 Ch29 Chicago, Nov 5 and 6, 1929 B30 Buffalo, May 20 and 21, 1930 C130 Cleveland, Nov 20 and 21, 1930 Ch31 Chicago, May 12 and 13, 1931- D31 Detroit, Nov 24 and 25, 1931 P32 Pittsburgh, May 24 and 25, 1932 Ch33 Chicago, June 29 and 30, 1933 P34 Pittsburgh, June 28 and 29, 1934 C135 Cincinnati, April 11 and 12, 1935 D36 Detroit, April 16 and 17, 1936 The list of papers mentioned in the first paragraph above is reprinted on pages 428 to 431 The Index of the Open Hearth Proceedings may be purchased at A I M E headquarters, 29 W 39th St, New York

Jan 1, 1936

By S. E. Bretherton

This title introduces the subject I wish to describe to my fellow members, very few of whom, I 'hope, have ever had as much trouble with the smelting of ore containing much zinc, either in the lead blast furnace or the matting furnace, as circumstances have forced upon me: First, for several years in Leadville, Colo., after the sulphide ores containing zinc had been developed with greater depth and were sold to the intereats with which I was connected for smelt-ing in the blast furnace for the recovery of the lead, silver, and gold; then, in New Mexico and Arizona, where the principal source of ore supply for our custom smelter was from miners who sent most of their product in the form of concentrates, which we briquetted and smelted in the blast furnace, producing a matte containing copper, silver, and gold, for which we were paid; together with some zinc and lead, which was penalized if in excess of a maximum base set by the refinery to which we sold our copper matte; last, but not least, my experience in Shasta county, Gal., where for the sake of recovering $13 per ton value in copper, silver, and gold, I have smelted ore containing as high as 40 per cent. zinc (the last 18,951 tons smelted averaged 15 3/10 per cent. zinc) which we not only lost, but which it cost us money to lose. After such an experience, and knowing that, instead of being worth only $13 per ton, such 15 per cent. zinc ore should be worth about $30, including zinc at the present market value, the question of recovering the zinc in a profitable manner from such ore became very interesting to me. During several years' time I sent samples, of from 5 to 1,200 lb. each, to be tested by the different best-known zinc-recovery plants, and experimented with several processes proposed by others for the treatment of such ore, with but little encouragement, until I

Jan 1, 1914

By H. E. Cline

Solidification of Pb-Sn alloys ranging in composition from 1.2 to 56 at. pct Pb ws observed with polarized light. Lamellar structures were observed over a larger range of compositions in alloys containing excess tin than excess lead, as expected from constitutional supercooling. The occurrence of pools of supercooled liquid surrounded by lead is explained by the difficulty in nucleating tin. Cells and dendrites weve observed in tin-rich alloys. Evidence was found that the degenerate structure formed at low growth rates, the formation of faults, and abrupt changes in composition and structure can be attributed to non-steady-state growth. The apparent interface shape was observed to have deep grooves at the interphase boundaries. HUNT and Jackson have observed the shape of the interface during growth of organic eutectics. They observed the formation of lamellar faults and shape instabilities upon changes in growth rate. The lamellar structure in these organic eutectics was not restricted to the eutectic composition. Recent work by Mollard and Flemings2 indicated that Pb-Sn alloys from 12 to 26 at. pct Pb could be solidified with a lamellar or rodlike structure if a sufficiently steep temperature gradient was used at a slow growth rate. Observations of the solid liquid interface of the Pb-Sn eutectic were made by Davies3 using polarized light. Photographs were at too low a magnification to determine the interface shape, but he has concluded that tin was the leading phase. In the following experiments, solidification of a range of Pb-Sn alloys from 1.2 to 56 at. pct Pb was observed using polarized light, to determine the factors controlling stability of the lamellar structure. EXPERIMENTAL Procedure. One hundred-gram ingots of alloys prepared from 99.999 pct pure Pb and Sn were cast into graphite molds under argon. The compositions of the alloys were 1.2, 6, 12, 26, 36, 46, and 56 at. pct Pb. Two-gram pieces were melted between two cover glass slides which were squeezed into a 1-mm separation. Samples were then observed under polarized light in a hot stage shown in Fig. 1. A long working distance objective designed for viewing at 500 times was used. Photography was made difficult by the lack of illumination and contrast at these high magnifications. By using an elliptical polarization compensator, as suggested by A. Holik, the contrast and illumination could be optimized. Photographs could be taken only at slow growth rates to avoid excessive interface motion during the 15-sec exposure used. The solidification rate was varied by increasing or decreasing the power to the heater. It was found that insulation was necessary to avoid undesired growth rate fluctuations. The temperature gradient, as measured with two thermocouples 1 cm apart, was 80" ± 20°C per cm during all the experiments reported here. The advantage of this procedure is in being able to observe solidification while it is occurring. However, the observations are restricted to the glass-metal surface and may be influenced by this surface. Also, one has no knowledge of the interior of the sample, in contrast to studies of the freezing of transparent organic eutectics.' Observations. The alloy near the eutectic composition (26 at. pct Pb) solidified in a lamellar structure when the growth rate was uniform. If the growth

Jan 1, 1968

By Robert S. Dewey

AS a result of drilling operations during 1943, West Texas again added sufficient new oil reserves to replace the oil produced during the year, but failed to maintain its position in currently available reserves because the deeper discoveries will require years for development. Drilling failed to provide the additional oil necessary to meet the increase in current and anticipated market demand. Although 13.3 per cent of the total footage drilled was in wildcat exploration, the ratio of oil discoveries to total wildcats was less in 1943 than in 1942, but comparable to that in 1941. Of the 732 field wells completed, 270 were at Slaughter, 55 at Wasson, 45 at Mascho and 31 at North Cowden. As of Dec. 31, 1943, there were 361 drilling wells including 71 wildcat and 290 field wells; 19.7 per cent were wildcats. It is anticipated that the percentage of wildcats of the total wells will be higher during 1944 than in either 1942 or 1943. Tables 3 and 4 present a three-year comparison of drilling activity and illustrate the downward trend of development that has been in effect during that time. Because of development lag in the deeper Ordovician fields, several years elapse before 2 sufficient number of wells is completed to give a substantial producing rate. As these new oil reserves cost more to find, and will cost more to produce on a barrel basis than the oil marketed during the year, their reserve replacement value to the industry is less in money. Costs While complete costs for deeper drilling are not yet available for analysis, it is evi- dent from the data on drilling rates to comparable depths, contract prices, and general increases in costs, that the cost of drilling has risen approximately 20 per cent during the year. One representative drilling contractor estimates that the average drilling time on a 5000-ft. field well has increased nearly one third and that out-of-pocket costs have increased a dollar per foot. Three major factors contribute to this increased cost: (I) less experienced labor, (2) deterioration in mechanical equipment and expendable material, and (3) increased contract prices. In the past, when there were more drilling rigs than wells to be drilled, some contractors would cut their drilling profit to keep their personnel and rigs working. As this practice is no longer necessary, the contract prices are adjusted upward to assure a profit. On deep and difficult drilling, contracts are let on a cost plus basis. A number of mechanical difficulties have become evident. Inferior quality of steel used in drill pipe and rock bits has added appreciably to drilling time and cost. Contractors are experiencing delay in obtaining repair work and repair parts for prime movers. As the length of drilling time required an shallow-field wells has not increased in proportion to that on deeper wells, it seems that the medium-sized drilling rig is better adapted mechanically than the heavy one to the work imposed. One of the main deficiencies in the heavy rig equipment is inadequate pump capacity. Drilling Mud The increasing amount of deep drilling has emphasized the importance and relationship of good mud to efficient and suc-

Jan 1, 1944

By Robert S. Dewey

AS a result of drilling operations during 1943, West Texas again added sufficient new oil reserves to replace the oil produced during the year, but failed to maintain its position in currently available reserves because the deeper discoveries will require years for development. Drilling failed to provide the additional oil necessary to meet the increase in current and anticipated market demand. Although 13.3 per cent of the total footage drilled was in wildcat exploration, the ratio of oil discoveries to total wildcats was less in 1943 than in 1942, but comparable to that in 1941. Of the 732 field wells completed, 270 were at Slaughter, 55 at Wasson, 45 at Mascho and 31 at North Cowden. As of Dec. 31, 1943, there were 361 drilling wells including 71 wildcat and 290 field wells; 19.7 per cent were wildcats. It is anticipated that the percentage of wildcats of the total wells will be higher during 1944 than in either 1942 or 1943. Tables 3 and 4 present a three-year comparison of drilling activity and illustrate the downward trend of development that has been in effect during that time. Because of development lag in the deeper Ordovician fields, several years elapse before 2 sufficient number of wells is completed to give a substantial producing rate. As these new oil reserves cost more to find, and will cost more to produce on a barrel basis than the oil marketed during the year, their reserve replacement value to the industry is less in money. Costs While complete costs for deeper drilling are not yet available for analysis, it is evi- dent from the data on drilling rates to comparable depths, contract prices, and general increases in costs, that the cost of drilling has risen approximately 20 per cent during the year. One representative drilling contractor estimates that the average drilling time on a 5000-ft. field well has increased nearly one third and that out-of-pocket costs have increased a dollar per foot. Three major factors contribute to this increased cost: (I) less experienced labor, (2) deterioration in mechanical equipment and expendable material, and (3) increased contract prices. In the past, when there were more drilling rigs than wells to be drilled, some contractors would cut their drilling profit to keep their personnel and rigs working. As this practice is no longer necessary, the contract prices are adjusted upward to assure a profit. On deep and difficult drilling, contracts are let on a cost plus basis. A number of mechanical difficulties have become evident. Inferior quality of steel used in drill pipe and rock bits has added appreciably to drilling time and cost. Contractors are experiencing delay in obtaining repair work and repair parts for prime movers. As the length of drilling time required an shallow-field wells has not increased in proportion to that on deeper wells, it seems that the medium-sized drilling rig is better adapted mechanically than the heavy one to the work imposed. One of the main deficiencies in the heavy rig equipment is inadequate pump capacity. Drilling Mud The increasing amount of deep drilling has emphasized the importance and relationship of good mud to efficient and suc-

Jan 1, 1944

By J. R. Finlay

BEFORE entering into the statistical part of this article, some general comments may be ln order. Each important war seems to introduce a new atmosphere and a new epoch. The Civil War led to the period of great interior development in North America, of the transcontinental railroads, and of large-scale manufactures. The first World War introduced the general use of the automobile, the building of a huge network of highways, the radio, and household engineering. Now I expect World War II also to introduce some new ways of living. Transocean aviation will become a commonplace; we shall probably have much more of an eye to our military and naval establishments and be more conscious of Eastern Hemisphere affairs instead of thinking so exclusively of the Western. Each war has also multiplied government expenditures and taxes; and to this rule the present one will certainly be no exception.

Jan 1, 1944

By George W. Maynard

(Pittsburg Meeting, March, 1910.) AT the Pittsburg meeting of the Institute, May, 1879, I made the first announcement in America of the results obtained by Sidney Gilchrist Thomas and Percy C. Gilchrist, ill their efforts to eliminate phosphorus in the manufacture of steel in the Bessemer converter and the open-hearth furnace.1 The first published statement in an American newspaper was a reprint of the first Thomas-Gilchrist paper, 2 which I sent to J. C. Bayles, at that time the editor. At the suggestion of many friends who were present at the Pittsburg meeting, and others who are cognizant of the beginnings of the process in the United States, and for the information of the younger generation of the iron and steel fraternity, I have thought it eminently proper that the history of the process in detail should be given where I made the first announcement and where the process has had its largest development. During my residence in England, from April, 1873, to February, 1879, and as a member of the Iron and Steel Institute since 1874, I was present at many of its meetings during those years. At nearly -every meeting the burden of discussion was the question of the use of pig-iron containing phosphorus in the. manufacture of steel by the Bessemer or the open-hearth process. In my biographical notice of Thomas;3 read at the New York meeting of, the Institute, February, 1885, I show that the working-out of the process was not a hap-hazard or accidental inspiration, but the culmination of many years of investigation of experiments and theories which had been carried on and advanced by chemists and metallurgists at home and abroad. 1 Trans., viii., .5 (1879-80). 2 The Iron Age, vol. 22, No. 17, p. 3 (Oct. 24, 1878). 3 Trans.. xiii., 785 to 791.

Jul 1, 1910

By H. O. Hoffman, C. D. Demond

There are two methods of determining the fusibility or refractoriness of fire-clays, the theoretical and the experimental. In the former, conclusions are drawn from the chemical composition; in the latter, from the changes which the clay undergoes when subjeoted to intense heat. It is well to use both methods, beginning with the actual heat-test and explaining the results obtained from this by the help of the chemical analysis. In discussing the subject, however, it is better to reverse this order. I. The Theoretical Method.* Leaving out the hygroscopic and combined waters and any organic matter, as not directly affecting the fire-resisting property, the refractory constituents of fire-clay are alumina and silica, and the fluxing constituents magnesia, lime, soda, potash and ferric oxide. According to Bischof,† alumina is the least fusible component, and silica follows close upon it. If, however, a mixture of the two be heated, it will be found that its melting-point is much lower than that of alumina, as a silicate will then have been formed. The way in which silica affects the refractoriness of alumina has been strikingly presented by Seger 1 in a diagram reproduced in Fig. 1. The abscissæ represent the melting-points of Seger cones Nos. 26 to 36 (see p. 55); the ordinates, the relative amounts of alumina and

Jan 1, 1895

By FRANK FIRRISTONE

Ix the summer of 1842 my father, William Firmstone, was engaged by Charles Jackson, Jr., of Boston, to examine the conditions in the Lehigh valley as a site for blast-furnaces using anthracite for fuel. In consequence of his report, he was further engaged by Mr. Jackson to build a furnace for him and his partners on the Lehigh canal, 2 miles above the mouth of the river at Easton. Work was begun in the fall of 1842, and the first furnace blown-in in 1844. The history of the works, therefore, from 1844 to 1887, when my own connection with them ceased, covers only four years less than the whole period of the rise, culmination, and commencement of the decline in the smelting of iron with anthracite in America, the beginning of which, in a commercial sense, may be put in 1839.' Although this paper, as the title indicates, is concerned almost exclusively with the furnaces at Glendon, still what was done there was more or less influenced by current opinion in the dis¬trict, and even reflects, to some extent, the changes in opinion and practice with mineral fuel the world over. No. 1 Furnace was built of red brick, on four piers, had three tuyeres and fore-hearth and tymp, as was universal with furnaces using mineral fuel until the introduction of Liirmann's cinder-tuyere. The dimensions and profile are shown in Figs. 1 and 2. The first hearth (Fig. 1) was of sandstone; all after were of fire-brick (Fig. 2). The profile was no doubt derived directly from Gibbons's furnace,2 for it appears from W. Firmstone's note-books that in October, 1840, he visited ." Gibbons' new furnaces building at Corbyn Hall," and I have an old drawing,\

Sep 1, 1909

By A. Thielen

In experiments for the production of steel the principal problem has always been the introduction into, or removal from, the iron of a definite quantity of carbon. Although the solution of this problem had engaged a more or less blindly and empirically directed effort for a long time, it was only with the development of analytical chemistry that the rôle which carbon plays in the constitution of steel was disclosed in its full significance, and that many of the problems confronting the steel-maker were thereby more clearly defined than before. For a long time, and to a certain extent even to this day, the percentage of carbon in steel has been the controlling means of deter mining its quality and hardness. In many cases the percentage of carbon alone has been relied on for judging large consignments, such as the large deliveries of wire-billets and blooms to America during the past twenty years; and though to-day the influences of the other constituents are recognized and many other considerations are taken into account, and though, moreover, some special steels, such as the Hadfield manganese steel, apparently dispense to a certain extent with the assistance of the carbon, yet fix our Bessemer, Thomas, Siemens and crucible steel the carbon still remains one of the most important constituents, and I venture to say it is indispensable. In order to produce in the Bessemer converter a steel of a certain required percentage of carbon, two methods, as is well known, present themselves. By the one the decarburization process is stopped when the desired carbon limit in the bath has been reached ; by the other the bath is completely decarburizecl, and then a calculated amount of carbon added in the form of spiegel, ferro manganese, etc. In Germany the latter method only was adopted, and it was retained when the Thomas-Gilchrist process for the production of low-Phosphorus steel from high-phosphorus iron eame into use, since from the nature of the new process complete decarburization is neces-

Jan 1, 1891

By C. M. WEILD

ATTENTION has been turned recently to the exploration and development of certain large blanket-deposits of brown iron-ore in Cuba. The most conspicuous of these to-day, and the one upon which the most light has been shed, is the Mayari deposit, situated about 15 miles south of Nipe bay. Here the Spanish-American Co. has sole control over 18,500 acres of ore-bearing lands, reported by its engineers to contain 500,000,000 tons of ore; and the necessary plant and equipment, with docks and railways, is now under construction for the early marketing of this ore. A similar deposit, and undoubtedly the next to be exploited, is the ore-field at Moa bay, where 13,000 to 15,000 acres of ore-lands, immediately adjacent to the shores of an excellent harbor, have been generously covered by numerous mining-claims, practically all controlled by four large interests. This deposit is now estimated to contain approximately 350,000,000 tons, on the basis of dried ore ready for shipment, a figure which may be increased when the western limits of the ore-deposit have been more accurately defined. Other deposits of the same type, but smaller and less accessible, are those at Cubitas, situated from 12 to 15 miles north of Camaguey city, and at Taco bay and Navas, points lying a few miles west of Baracoa. The area of the Cubitas deposit is said to be 6,000 acres, and the yield of ore is estimated at 150,000,000 tons. The Baracoa. deposits are less well known, but preliminary estimates have placed their joint ore-reserves at 40,000,000 tons. Accepting the above tonnages as reasonably correct, we conclude that the deposits enumerated give promise of adding about 1,000,000,000 tons of iron-ore to the world's supply; they have, therefore, to be considered in any attempt to fore-

Aug 1, 1909