Search Documents

By WALTER M. DAKE

GENERALY speaking, the bituminous coal mines of the country are being operated at a loss. To purchasers of the necessary commodity, a statement of this character may have the sound of a far fetched propagandist cry; but to the coal producer who lives in the hope of an up-turn in the almost stationary market price of his product, while inking in red his monthly operating balances, it carries the ringing sound of truth.

Jan 1, 1925

By E. M. Murphy

(Presented by invitation at a meeting of the Spokane Local Section of the Institute, Feb. 17, 1912.) EIGHT years ago the Hecla mine, a lead-silver producer, situated at Burke, Idaho, was producing ore from but two levels, the 300- and the 600-ft. All hoisting was done with a 12- by 16-in. slide-valve, double-reel, hoist. The hoist was being worked to its capacity and was unsuitable for hoisting from greater depths. As the work of opening a new level was about to be started, it became necessary to remodel the then-existing equipment or install a new hoist. The recent advent of electricity from Spokane had made available a cheaper power than steam. By a series of tests conducted throughout the Coeur d'Alène district, it was found that it cost $109 per year to generate a horse-power with steam. Electric power was to be had for $50 a horse-power per year. It was decided to substitute for the engines a motor-drive, of sufficient capacity to operate from the 900-ft. level, and ultimately install an entirely new hoist. After disconnecting the engines, installing a new shaft, and making a few minor changes, a 300-h-p., 2,300-volt, 514-rev. per min., variable-speed motor of the induction type was geared to the reel-shaft. The reels were supplied with 3/8 by 4-in. flat rope, and the duty of the hoist was about as follows: Cage, 1,700; ore, 2,600; car, 1,400; rope, 2,250; total, 7,950 pounds. The Bristol ammeter chart, Fig. 1, shows the combined current-consumption of the hoist- and mine-motors. The large intermittent load is clearly shown ; this produced harmful fluctuations in the voltage of the long, lightly-loaded, 60,000-volt transmission-line from Spokane to the Coeur d'Alènes. The power company received no compensation for the increased cost of producing power for this intermittent or fluctuating load. In order to protect its system from similar excessive

Sep 1, 1912

By AIME AIME

THOUGH the dust-control systems in the crushing plants and other buildings at Morenci do not differ materially from similar installations in other large copper reduction works, it is probable that in few other plants has as much attention been paid to the dust problem. Possibly the most striking feature of the Morenci installation is the manner in which the necessary equipment has been built into the various structures, and the absence of unsightly pipes, ducts, and fan houses. That this result has been attained is due, in no small part, to the basic conception that the control of the dust in a milling plant should be an essential part of the process itself and not something to be tacked on later after the plant is in operation. The control systems were designed and developed along with the general plant construction program and when the first car of ore was dumped into the crusher the dust-control equipment was ready.

Jan 1, 1942

Separates of all the Technical Publications published in 1931 are available at Institute headquarters. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found in the Transactions. Copies of these papers have been mailed to those members of the Institute who are registered in the different classes: A-Metal Mining; B-Milling and Concentration; C-Iron and Steel Division; D-Nonferrous Metallurgy; E-Institute of Metals Division; F-Coal Division; G-Petroleum Division; H-Nonmetallic Minerals; I-Mining Geology; K-Mining Administration; L-Geophysical Prospecting. Other members may obtain copies by writing to the Secretary. Additional copies are sold at the rate of I cent per page; minimum charge, 25 cents. Metal Mining Tech-nical Publi- Title Author Meeting TRanb. cation Volume No. and Page* 411-A.43 Ventilation at the Portovelo Mines, J. P. Harmon New York. T31, 83 Ecuador (18) Feb., 1931 425-A.44 Use of Models for the Study of Mining P. B. Bucky New York, Problems (28) Feb., 1931 Milling and Concentration 375-B.32 Ball Mill Studies, I (53) A. W. Fahrenwald New York, H. E. Lee Feb.. 1931 401-B.33 Experimental Flotation of Oxidized H. S. Gieser New York. Silver Ores (9) Feb., 1931 410-B.34 Flotation of Minor Gold in Large-scale E. S. Leaver New York, Copper Concentrators (32) J. A. Woolf Feb., 1931 414-B.35 Effect of Particle Size on Flotation A. M. Gaudin New York, (23) J. 0. Groh Feb., 1931 H. B. Henderson 416-B.36 Ball Mill Studies, 11.—Thermal A. W. Fahrenwald New York. Determinations of Ball Mill Effi- G. W. Hammar Feb., 1931 ciency (13) H. E. Lee W. W. Staley Iron and Steel Division 38QC.59 Open-hearth Steel Process as a Prob- E. R. Jette New York, C31, 80, 111 Iem in Chemical Kinetics (34) Feb., 1931 381-C.60 Thermodynamic Study of the Phasial Yap, Chu-Phay New York. Equi1ibriain the System Iron-car- Feb., 1931 bon (26) 382-(3.61 Influence of Dissolved Carbide on the Yap, Chu-Phay New York, Equilibria of the System Iron-car- Feb., 1931 ban (19) 383-C.62 Research on Blast-furnace Slags. R. S. McCaffery New York, Three papers (88) Co-workers Feb., 1931 384-C.63 Statistical Analysis of Blast-furnace K. S. McCaffery New York, C31, 60, 70 Data (13) R. G. Stephenson Feb., 1931

Jan 1, 1931

By J. G. Bouwkamp

This paper presents three general approaches towards the solution of the stress distribution and the behavior of tubular connections as used in offshore well drilling structures. First, the possibilities of using plastic models and photoelasticity techniques in evaluating the stress distribution in gusset plate connections are analyzed. The results of photoelastic studies on the stress distribution in the in-plane gusset plate of two-dimensional joints are presented. The influence of the configuration of the gusset plate (with and without cut-outs) is discussed. Second, the paper deals with recent developments and applications of computer programs to analyze connections with directly inter-welded tubes and with gusset plates. The possibilities and limitations of these programs are discussed. Stress patterns analyzed with these programs are presented for different joint configurations. Finally, the basic test procedures and results of a test on a tubular joint under static and alternating loads are discussed. INTRODUCTION The effective design of tubular connections as encountered in offshore well drilling towers or floating platforms has been complicated basically by the radial flexibility of the tube walls. This flexibility is a source of severe stress concentrations which can initiate an early failure of these joints. In an attempt to reduce the influence of the wall flexibility of the column tube, certain joints are presently designed by inter-welding the incoming branch members. In those designs, the force acting normal to the chord tube can be reduced considerably. A second group of joints incorporate gusset plates or stiffening rings to stiffen the column wall and to distribute the incoming branch member forces over a larger part of this wall. A third approach to improve the stress distribution in a tubular joint is to increase the wall thickness of the column member. This can be achieved by simply applying a thicker wall section in the vicinity of the joint. A fourth possibility to restrain the radial flexibility of the tube wall is to fill the column member with concrete. Also, a single, cast steel seat welded to the column tube can be used to improve the stress distribution in this wall. Although all these designs improve, in general, the state of stress in the column wall, the altered stiffness often causes the development of critically stressed areas in the web members. At the same time the actual design in most instances is decisively influenced by the site which governs the depth and controls the forces produced by waves, earthquakes and ice flow. Also, the towing, erection and foundation requirements of offshore structures can affect the actual design selection. Because of the complexity of the structural configuration of tubular joints, the stress analysis of these connections has necessarily been based on simplified and often crude assumptions. For the earlier and smaller type of connections with about 4-ft diameter column sections, the primary problem was to evaluate the relative stiffness of the column wall section and the load transfer between joint members. Due to the recent developments of offshore drilling structures with increasingly larger connections (e.g., column diameter. 32 ft; web members, 8.5 ft) this problem has become even more critical. One design philosophy for such large joints follows a member-to-member connection with radially heavy reinforced column sections. This radial stiffness can be attained by closely spaced and intensively stiffened horizontal diaphrams together with vertical stiffeners. A second solution incorporates a concrete-filled section between the outer and inner walls of the column tube. Another philosophy considers large gusset-plated joints. The problem in these joints is to develop an effective load transfer between the branch tubes and the gusset plate and to minimize the stress concentrations in the member walls as effectively as possible. Several concepts are followed to achieve this gradual transfer between web-member walls and gusset plates. Because the number of joints in these huge platforms is limited compared to the over-all size, a proper design of these joints is even more important than was the case for the many joints in the smaller, but multi-legged towers. A failure of one of those ultra-large joints could well cause the complete collapse of such a structure. Under these circumstances an accurate analysis of the large joints is of the greatest importance, together with information regarding the expected behavior of such joints under critical alternating load conditions. Recent applications of photoelastic model techniques have proved to be quite effective in evaluating the elastic behavior of such joints. Although a complete study of such connections is quite well possible with present-day photoelastic techniques, it might often be feasible and necessary to limit the objectives and to restrict these investigations to the study of a specific aspect of the joint. Another very promising avenue of approach to solve the complex stress pattern in these connections seems to be the recent development of digital computer programs. In this category, cylindrical shell programs and finite element methods for more complex configurations have

Jan 1, 1967

By R. P. Abendroth

This study is concerned with the kinetics of selective oxidation of chromium in a commercial Fe-Cr-Ni alloy. Selective oxidation of chromium in this alloy, by use of a low oxygen-potential atmosphere, leads to the formation of a compact, protective layer of Cr2O3. This layer serves to protect this alloy from gross scaling when it is subsequently exposed to severe oxidizing conditions at high temperature. The interaction of low oxygen-potential atmospheres close to equilibrium with Fe-Cr and Ni-Cr alloys has been studied by others."' These studies werk concerned with the surface-structure variations under slightly oxidizing conditions. NO detailed study was made of the oxide scale formation kinetics, however. The alloy samples were cut from 0.012-in.-thick sheet, with an apparent surface area of 7.1 sq cm. These sheet samples were abraded through 4/0 metallographic paper, and washed in alcohol and acetone. The analysis of the sheet alloy is (in weight percent): 42 pct Ni, 5.5 pct Cr, 0.09 pct C, 0.18 pct Al, 0.36 pct Si, 0.26 pct Mn, balance Fe. The weight gain vs time data were obtained with a 2-g capacity fused-silica spring—cathetometer system. The spring deflection was optically magnified ten times before being read by the cathetometer. A sensitivity of about 0.01 mg was attainable. The spring was enclosed in a water jacket maintained at 60°C to minimize the effect of temperature changes. The sample was suspended from the spring with a fused-silica hangdown and was positioned in the thermal center of a mullite furnace tube. Sample temperature was read with the aid of a thermocouple placed outside the mullite tube and an inside vs outside temperature calibration. Temperature change during the course of a run was ±0.25°C, with a temperature gradient of less than l.O°C over the length of the sample. Total temperature uncertainty was no more than ±3.0°C. Alignment difficulties between the hangdown and radiation shields in the furnace tube required that the sample be positioned in the furnace when cold, and heated with the furnace until the temperature stabilized at the desired point. This required 5 to 6 hr, and was carried out in Matheson ultrahigh-purity hydrogen. Oxidation was started, after evacuation, by introducing a hydrogen-water vapor mixture, obtained by saturating hydrogen with water vapor at 31.00o ± 0.02oC. Oxidation was continued for 90 min. Gas flow was 300 ml per min during heat up and oxidation. Since only several milligrams of oxide are formed on each sample, chemical analysis of the oxide is difficult. A representative analysis is: 80 pct Cr2O3, 5 pct Fe2O3, 3 pct Al2O3, 4 pct MnO, 7 pct SiO2, 1 pct or less NiO. X-ray diffraction analysis of the oxide as formed on the alloy gives rhombohedra1 Cr2O3, and barely distinguishable amounts of a cubic spinel phase, and possibly AlZOs and SO2. The identification of these latter two compounds is by no means certain. The spinel phase could be based on iron or manganese as these elements are present in significant amounts in the oxide. The results of the kinetic studies using 31°C dew-point hydrogen-water vapor mixtures were found to conform to a parabolic rate law. In many cases the parabolic plot consisted of two intersecting straight lines, defining an early and a late rate for a particular run, and in the other cases the parabolic plot consisted of one straight line for the entire run. The slopes of the various straight lines were determined by the method of least squares. Reproducibility of the data was good enough for multiple runs at the same temperature such that the value given for the rate constant is the average for two or more closely similar values, rather than widely varying values of the rate, where more than one determination is indicated in Table I. The exhibition of only one or of two rate constants during a run can happen at the same temperature. Thus, Table I shows that at 11'74°C a single rate constant was obtained from one sample, while other samples oxidized at the same temperature gave an early and a late rate constant. It should be noted that the single rate constant corresponds very closely with the early rate constant. This is also true at 1153°C. The time at which the late rate started to appear was variable, usually occurring 20 to 40 min after oxidation had started.

Jan 1, 1964

BUMPS in No. 2 Mine, Springhill, N. S., furnished the main feature for discussion at the morning meeting* on Ground Movement and Subsidence on Feb. 18. Walter Herd, the author of the paper by which the discussion was introduced, not being well, was unable to be present. The paper was presented by T. L. McCall, who laid stress on the presence of sand- stone as the cause of bumps, on the value of retreating longwall in eliminating such phenomena at the coal face and on the advantage of wide headings with packs on either side, leaving space behind them for any coal that bumps might dislodge. George S. Rice, who presided, referred to his visits to the Nova Scotia mines and said that bumps usually occurred only where the coal was thick and strong and the roof and floor both more than usually hard. If any of the three were weak, bumps were not likely to occur. In the Nova Scotia mine, to which Mr. Herd referred, there was no material for packwalls and for this reason as well as for safety he had been convinced that long- wall retreating with a small percentage of pack walling was the most feasible plan.

Jan 1, 1929

By R. R. Vandervoort

The creep behavior of Nb(Cb), Ta, Mo, and W was determined under conditions of constant atomic dif-fzisivity, constant stress to elastic modulus ratio, and nearly equivalent grain size, and the steady-state creep rates obtained from these tests were correlated with calculated stacking fault energies for the metals. These results, in conjunction with similar data for several fccMetals,13 suggest that stacking fault energy may influence the creep strength ofbcc metals. The interrelationship between steady-state creep rate, subgrain size, and stacking fault energy was examined. It was found that the subgrain size for a given creep stress, increased as stacking fault energy increased, but that this relationship did not cormpletely account for the effect of stacking fault energy on creep rate. The crystallography and energetics of stacking fault formation in bcc metals has been discussed by a num-ber of authors,1-5 and impurity stabilized stacking faults on (112) planes have been observed in Nb,6,7 w,8,9 Fe,] and V" by transmission electron microscopy. However, a crucial question is whether or not stack-ing faults influence the mechanical strength of bcc metals. Potentially, stacking faults could increase strength by reducing the mobility of the partial dis-locations bounding the fault, by acting as barriers to slip dislocations, and by retarding the climb of dislo-cations during high-temperature deformation. The objective of this study was to seek a correlation be-tween creep strength and stacking fault energy for several bcc metals; namely, Nb, Ta, Mo, and W. The creep behavior of most polycrystalline metals and alloys at high temperatures and moderate stresses can be described by the following relation:11,12 im=Af(s) where i, = minimum creep rate, A = constant, j(s) = a function involving metallurgical structure, a = applied stress, E = average elastic modulus at the test tempera-ture, w = constant (equal to 5 for most pure metals), D = diffusion coefficient. One factor in the structure function F(s) which sig- R. R. VANDERVOORT, Member AlME is Research Metallurgist, Process and Materials Development Division, Chemistry Department, Lawrence Radiation Laboratory, University of California, Livermore, Calif. Manuscript submitted February 28, 1969. IMD nificantly affects the creep resistance of fcc metals is stacking fault energy, and creep rate has been shown to vary directly with stacking fault energy to the 3.5 power." In the latter investigation, four fcc metals of widely different stacking fault energies (Ag, Cu, Ni, and Al) were creep tested at a constant stress to modulus ratio of 1.21 x 10-4, at a constant diffusivity of 2.7 x 10-12 sq cm per sec, and at nearly equivalent grain sizes of about 0.7 mm. The creep data were then correlated with stacking fault energies. In the present study, a similar procedure was followed. All materials used in this work were consolidated by powder metallurgy techniques. Impurity contents in the as-received materials are listed in Table I. Chemical analyses showed that no measurable contamination of the test specimens occurred during pretest annealing treatments or creep testing. Specimens with a gage section 0.75 by 0.125 by 0.050 in. were creep tested in tension in a vacuum of less than 10-9 torr. Deformation at temperature was measured by tracking fiducial marks on the gage section of the specimen with an optical comparator. Optical deformation measurements also permitted observation of the macroscopic characteristics of the deformation Table I. Typical Specimen Impurity Content, ppm Nb Ta Mo W C 45 10 155 6 O 185 30 4 10 N 30 6 3 2 H 5 I 1 <1 als 3 10 2 15 Ca <5 I3 5 Cr 5 <3 10 <5 Cu 10 50 2 15 Fc 10 10 150 35 Ni 2 150 20 <5 Si <I0 1 3 <10 Ta 100 Ti 10 8 1 Zi 15 50 1 3 Table II. Test Conditions for Constant Stress-Modulus Ratio of 6 X 10.&apos; and Constant Diffusivity of 2.7 X 10-12 sq cm per see, and Grain Size Values for the Given Pretest Annealing Treatments Literature references Pretest Annealing for E and D Treatment Stress, Temperature, ___"&apos;Values__ Grain Tempera-Metal psi "C E D Size, mm ture, .C Time hr Nb 745 1525 14 15 to 17 0.83 1650 I Ta 1220 1770 18 19.20 O.91 1800 I Mo 1975 1630 18 21 0.77 2200 I W 2140 2265 18 22 040 2400 5

Jan 1, 1970

By T. T. Read

FOR the second time the Mineral Industry Education Division opened the sessions at the Annual Meeting by gathering at the Engineering Woman&apos;s Club, Sunday at 3 p. in., and, in spite of the informality of the hour, with a good attendance of representative men in the educational field. The chairman of the Division, Thomas T. Read, after briefly reviewing some of the more significant events of the past year, introduced H. P. Hammond, professor of civil engineering, Brooklyn Polytechnic Institute, a leading figure in the project of the Engineers&apos; Council for Professional Development for accrediting engineering schools. Prof. Hammond made it clear that the project is not to rate engineering schools but to accredit them; not to arrange them in order of excellence, but to segregate them into two groups, those that are entitled to recognition as genuine engineering schools, and those that are not. About thirty schools in the whole country will presumably fall into the latter class; they are typified by an unnamed institution where the teacher of mathematics bears the title of Professor of Civil Engineering and the man who teaches chemistry that of Professor of Chemical Engineering, and having no engineering instruction except some elementary surveying, but still claiming in its catalogue to be an engineering college. While everyone would like to avoid the necessity of accrediting engineering colleges, it cannot be avoided, since the University of the State of New York, and several other agencies, are already doing it. If it cannot be avoided it is best that it should be done by a qualified agency set up by the national engineering societies, so that the results may command respect and general acceptance. It is for this reason, and this alone, that the accrediting committee of the E. C. P. D. has been set up. It is now ready to begin its task, and during-the coming year it will accredit the schools in two of the seven geographical districts into which the country has been divided, beginning with New England and the Mid-Atlantic States.

Jan 1, 1935

By Charles E. Locke

DEPRESSION in all lines of the mineral industry except gold, which began in 1930 and continued, even worse, through 1931, had its effect on ore concentration. Construction was limited to the completion of plants already begun. Every possible economy was adopted. Changes and improvements involving expense were postponed. Research was largely abandoned. Operations became highly efficient and costs were cut down, although this did not necessarily mean a lower cost per ton because of the greatly reduced capacity at which mills were run. Lower metal prices caused the operators to seek the optimum ratio of concentration and grade of concentrates looking toward maximum economic recovery; that is, net profit. In the crushing field no marked changes occurred. The Symons cone crusher for intermediate work is in use almost everywhere. Its manufacturers claim that 900 machines have been installed in 21 countries, replacing two previous steps of crushing and yielding a product sufficiently fine to form a satisfactory feed for rod mills and ball mills. A new Telsmith crusher has appeared which has curved jaws something like the Symons cone and consequently the same advantage as the latter.

Jan 1, 1932

By AIME AIME

The 102d meeting of the Institute was held at the Institute headquarters in the Engineering Societies Building, New York, N. Y., on Feb. 19, 20 and 21, 1912. A Bureau of Information, in charge. of Mr. George Buckman, was maintained during the meeting. The proceedings opened with an informal social meeting on Monday evening, Feb. 19, in Assembly-Room No. 1, on the

Mar 1, 1912

By Bradley Stoughton

As a part of the systematic study of the alloys of iron under the auspices of the Engineering Foundation, and preliminary to the commencement of comprehensive work on this larger subject, the authors have undertaken an investigation of the available literature dealing: with the alloys of iron and silicon. The purpose is to collect all the data in English and foreign languages and present them in two mono-graphs, one of a more scientific and the second of a more industrially useful nature. Of course, a great deal of information upon the constitution of the iron-silicon alloys was found specificially upon the changes of phase in the equilibrium diagram and the different phases present, such as solid solution, chemical compounds (iron silicides), etc. While no extended research was contemplated in the particular study undertaken, nevertheless the data collected proved to be so contradictory in many respects that a simple study of some of the outstanding problems involved in the constitution and equilibrium diagram was undertaken Because research was not a primary object of the work, and also because of the extreme industrial importance of the silicon alloys between 0.80 and 14 per cent. silicon, and finally because of the unsatisfactory state of knowledge existing as to these alloys, the experimental investigation was limited entirely to alloys with less than 10 per cent. silicon.

Jan 1, 1930

By J. A. Retty

IN the Labrador iron fields two concessions, totaling nearly 24,000 square miles, have been staked out and commercial-grade deposits delineated. The Newfoundland-Labrador concession, owned by the Labrador Mining and Exploration Co. Ltd., is a 20,000-square-mile tract in the upper basins of the Hamilton and N askaupi Rivers which drain into Lake Melville. The New Quebec licensed area is 3900 square miles, owned by the Hollinger North Shore Exploration Co. Ltd., lying to the northwest of the northwestern part of the Labrador concession. It includes the upper basin of the Swampy Bay River and part of the upper basin of the Whale River, both of which drain into Ungava Bay. Both of the above-named companies are controlled by Hollinger Consolidated Gold Mines Ltd. with The M. A. Hanna Co., of Cleveland, holding a minority interest. When exploration was first undertaken in 1936, the only published map of the area was that prepared by A. P. Low in 1895. It showed only the main watercourses and gave only a rough, general idea of the geology. The numerous lakes of this vast area had to be first sketched and then mapped. Since then, extensive geological and topographical surveys have been conducted by the Labrador company, work which is normally done by Government branches. The object of the work was to examine the area and gradually eliminate unfavorable or less favorable prospecting ground. With this object in view, geological

Jan 1, 1948

By H. C. George

IN 1901, the United States produced 69 million barrels of crude oil, which was 41.4 per cent of the world production. By 1931, these figures were 850 million barrels and 62.1 per cent respectively, showing over this period of thirty years an increase in the world production of 718 per cent. Over this same period, the increase in the demand for technically trained men in the industry was much greater than the increase in crude-oil production. This was because much of the increase in production was secured by the application of geology and physics to the finding of new oil fields and by .the development of engineering methods and equipment incident to drilling and producing from much greater .depths.

Jan 1, 1934

By Sidney H. Haughton

WHEN the white pioneers of the eighteenth and nineteenth centuries advanced from the coastal settlements of southern Africa into the interior of the subcontinent, they found it inhabited, more or less sparsely, by brown or black peoples mainly of pastoral habits but equipped with a fighting spirit and certain fighting weapons. Some of the tribes were smiths, others were miners and metallurgists; all used fuel, either industrially or domestically. Some of that fuel was wood, some cattle dung, and in some places the natives mined outcrop coal. Coal was first discovered by Europeans in Natal about 1840. After proper deliberation and after allowing due time for a consideration of all the implications, the Natal Government decided in 1881 (40 years after) to import an English expert to investigate and report on the discovery. Things then moved rapidly, and in what to a geologist is the remarkably short space of eight years, Natal collieries were producing at the rate of nearly 30,000 long tons per annum or 100 long tons per working day!

Jan 1, 1945

By T. S. Fuller

THE work of D. J. McAdam1,2 at the U. S. Naval Engineering Experiment Station, Annapolis, Md., on what has been called by him "corrosion fatigue" has focussed the attention of the engineering profession in general, and of those interested especially in the study of corrosion in particular, on the importance of making tests which will indicate as nearly as possible what can be expected from a given material in service. Pitting is unquestionably the chief agent operating so tremendously to reduce fatigue limits, but in the light of previous work3, 4, 5, 6, 7, 8 it is fair to assume that absorbed hydrogen resulting from the action of the corroding medium upon steel may, under certain conditions, have a perceptible influence. The experiments described in this paper deal more precisely with stressless corrosion, or "prior-corrosion fatigue, "9 and have been carried out to test such an assumption, to segregate, if possible, the effect of pitting from that of absorbed hydrogen, and although very preliminary in nature they indicate results which are striking.

Jan 1, 1929

By T. S. Fuller

The work of D. J. McAdam, Jr.1,2 at the U. S. Naval Engineering Experiment Station, Annapolis, Md., on what has been called by him "corrosion-fatigue" has focussed the attention of the engineering profession in general, and of those interested especially in the study of corrosion in particular, on the importance of making tests which will indicate as nearly as possible what can be expected from a given material in service. Pitting is unquestionably the chief agent operating so tremendously to reduce fatigue limits, but in the light of previous work3, 4, 5, 6, 7, 8 it is fair to assume that absorbed hydrogen resulting from the action of the corroding medium upon steel may, under certain conditions, have a perceptible influence. The experiments described in this paper deal more precisely with stressless corrosion, or "prior-corrosion fatigue,"9 and have been carried out to test such an assumption, to segregate, if possible, the effect of pitting from that of absorbed hydrogen, and although very preliminary in nature they indicate results which are striking.

Jan 1, 1929

By T. S. Fuller

The work of D. J. McAdam, Jr.1,2 at the U. S. Naval Engineering Experiment Station, Annapolis, Md., on what has been called by him "corrosion-fatigue" has focussed the attention of the engineering profession in general, and of those interested especially in the study of corrosion in particular, on the importance of making tests which will indicate as nearly as possible what can be expected from a given material in service. Pitting is unquestionably the chief agent operating so tremendously to reduce fatigue limits, but in the light of previous work3, 4, 5, 6, 7, 8 it is fair to assume that absorbed hydrogen resulting from the action of the corroding medium upon steel may, under certain conditions, have a perceptible influence. The experiments described in this paper deal more precisely with stressless corrosion, or "prior-corrosion fatigue,"9 and have been carried out to test such an assumption, to segregate, if possible, the effect of pitting from that of absorbed hydrogen, and although very preliminary in nature they indicate results which are striking.

Jan 1, 1929

By M. Smutz, C. J. Baroch, E. H. Olson

IN 1949 an orebody containing some 10 billion lb of recoverable rare earth metals was discovered in the Mountain Pass district of San Bernardino County, California.&apos; The following year Molybdenum Corp. of America purchased a number of claims at the deposit and a mill on the property which had been constructed to process the district&apos;s gold ores. Average composition of ore from the San Bernardino deposit is less than 0.1 pct Tho2, 25 to 35 pct calcite, 10 pct rare earth oxides, 15 to 20 pct silica, and 30 to 40 pct barite.&apos; Rare earth content of the ore analyzes 50.7 pct CeO2, 4.2 pct Pr6O11, 11.7 pct Nd2O3;, 1.3 pct Sm2O3,, and 34.3 pct La2O3 and others.&apos; By floating the barite and depressing the bastna-site, Molybdenum Corp. of America produced a concentrate that contained 60 to 70 pct rare earth oxides. More than 25 pct of the rare earths, however, was lost in flotation. It seemed likely that a more economical method could be found. At the present time most of the rare earths in the concentrates are converted to rare earth chlorides, which are either fed to ion exchange columns for separation of the individual rare earths or reduced to misch metal. Current investigation shows that solvent extraction may achieve this separation more economically than ion exchange. The study reported here was undertaken to develop an economical method of preparing a pure rare earth nitrate mixture from California bastnasite ore. Results indicated that more than 98 pct of the rare earths could be recovered. Several possibilities were considered for processing bastnasite ore, but only the method outlined in Fig. 1 was investigated. This involved leaching the calcined ore with nitric acid. The nitric acid process is discussed under the following headings: 1) calcination of the ore, 2) leaching of calcine, 3) filtration studies, 4) solvent extraction, and 5) nitric acid recovery. Calcination: Since California bastnasite ore contains 25 to 35 pct calcite and about 10 pct bastnasite, calcination was needed to reduce the violence of reaction with nitric acid. Weight losses of 26 to 30 pct were obtained by calcining the ore at 900°C for I hr or at 800°C for 4 hr. Longer periods resulted in no further weight loss. Leaching the Calcine: When the bastnasite calcine was leached with 30 pct nitric acid for 8 to 10 days, rare earth recoveries of only 45 to 50 pct were

Jan 1, 1960

By George D. Graffin.

The first use of graphite is lost in the mists of time. It was used by primitive man to make drawings on the walls of caves and by the Egyptians to decorate pottery. As early as 1400 A.D. graphite crucibles were being made in the Haffnerzell district of Bavaria. Through the Middle Ages graphite was confused with other minerals, especially galena and molybdenite. Two common names that are still used for the mineral are "Plumbago," meaning leadlike, and "Black Lead." The latter name implied that graphite is either composed of lead or at least contains a large percentage of it. Gessner is credited with having recognized it as a separate mineral in 1565, but its composition was not determined until 1779, when Scheele demonstrated that graphite oxidized to carbon dioxide, thus proving its carbon constitution. In 1789, Werner named it "graphite" from the Greek word "graphein," meaning to write. The United States has long relied on foreign countries for its graphite supplies. This reliance has been due more to the lack of suitable domestic graphites than to any particular preference for buying minerals overseas. Ceylon (now Sri Lanka) graphites were imported as early as 1820, and Madagascar graphites have been imported since the properties on that island were opened up about a hundred years later. Mexico has long supplied the United States with most of its requirements for amorphous graphite. Physical Properties and Classification Graphite is found in laminated, flaky aggregates disseminated in schistose rocks. It also occurs in veins and exhibits a foliated or fibrous structure. Graphite is a black lustrous mineral that crystallizes in the hexagonal system, with rhombohedral symmetry. The crystals have tabular form and are six-sided; the faces are commonly striated. The flakes have perfect basal cleavage and are opaque. When well crystallized, the flakes have a black metallic luster while the amorphous material is black and earthy, with a microcrystalline compactness. The flakes feel greasy. Graphite is an excellent conductor of heat and electricity. It melts at approximately 3550°C at a triple point under 1250 psi. It sublimes between 3300-3500°C at 14.7 psi. At 3726°C a second triple point occurs at approximately 100,000 atmospheres. Thermal oxidation in the presence of oxygen begins at 300°C and the rate increases with temperature. The three forms of carbon (charcoal, graphite, and diamond) are distinguished by chemical and physical tests. The specific gravity of charcoal is 1.3 to 1.9, of graphite 2.266 g/ cm3 (crystal density), and of diamond 3.5. Graphite has a hardness of 1 to 2 (Mohs&apos; scale). Natural graphite can be divided into three classes: disseminated flake, crystalline vein (fibrous or columnar), and amorphous. Flake graphite is a lamellar form found in metamorphic rocks, such as marble, gneiss, and schist. Each flake is separate, having crystallized as such in the rock. Crystalline vein graphite is found in the form of well defined veins or as pocket accumulations along the intrusive contacts of pegmatites with limestones. The graphite of such deposits is of two types, foliated and columnar. The important Sri Lanka (Ceylon) deposits are vein type. Amorphous graphite is commonly found as minute microcrystalline particles more or less uniformly distributed in feebly metamorphic rocks, such as slates and shales, or in beds consisting practically entirely of graphite. The latter usually are metamorphosed coal seams and carry as much as 80-85% graphitic carbon, while the former, being altered carbonaceous sediments, commonly range from 25 to 60%

Jan 1, 1983