Search Documents

By AIME AIME

MESSRS. BURT and Shockley and others have been for three years urging upon the Institute the matter of simplified spelling. The Institute endeavors to be progressive in the matter of spelling and. is in cooperation with the national body which has this in hand and which has its principal office in New York. Our spellings are changed as fast as-good usage will permit (so it seems to the Board of Directors) and the national body, which is the real representative of the simplified spelling interests, deems that the Institute is making real progress, although not quite as fast as extremists would wish. In January, 1919, Mr. Shockley sent out letter ballots which created a misconception in the minds of many members, who received the impression that the communications came from the Institute instead of from a small group of members. As a result of this propaganda 163 proposal-ballots were sent in to the Institute divided as follows: Yes ?114 No ?20 Negative letters ?9 Split ballots ?20 Total ?163 The total membership at this time was about 7200. The disgusted members would not vote.

Jan 1, 1920

By F. B. Plummer, R. B. Newcome

The practice of introducing acid into oil wells to increase production of oil and gas has been in use since 1894, when it was first used in the Pennsylvania oil fields30.‡ It is only since 1928 that it has been used to any extent in the Mid-Continent18. The process has proved successful in increasing production, at least temporarily, in depleted oil fields where the producing formation is highly calcareous and where water drive is not too pronounced. In the Zwolle field in Louisiana, where the producing horizon is a chalk, increases of 100 per cent have been recorded25. In north-central Texas, where the oil is produced from the Marble Falls limestone, equally pronounced increases have resulted3. The production also in some fields yielding oil from quartz sand cemented with calcitc has been benefited. The evidence of actual increase in total recovery of oil, however, has been questioned by some engineers18. It has been pointed out that the results of the treatment of a well in a now district, where the process has never been tried out, can never be predicted with certainty, since other factors besides percentage of calcareous content of the oil sand play a large part in determining the success of the method. Numerous articles have been published on acid treatment and on the effects of acid on limestone1-35, yet very little has been written concerning experimental work on the actual effect of acid on capillary pores and larger oil-coated voids of oil sands. This is due partly to difficulties in duplicating field conditions in a laboratory and partly to the fact that the process has been carried out largely by contracting companies that have been unwilling to publish details of their results for fear of loss of business to competitors. The authors, using equipment developed to measure the radial permeability of oil-sand cores2', have developed a method of investigating the results of acid treatment which has enabled them to test numerous cores and to study in some detail the action of acid on the different types of rocks, particularly fine-grained rocks.

Jan 1, 1936

By F. B. Plummer, R. B. Newcome

The practice of introducing acid into oil wells to increase production of oil and gas has been in use since 1894, when it was first used in the Pennsylvania oil fields30.‡ It is only since 1928 that it has been used to any extent in the Mid-Continent18. The process has proved successful in increasing production, at least temporarily, in depleted oil fields where the producing formation is highly calcareous and where water drive is not too pronounced. In the Zwolle field in Louisiana, where the producing horizon is a chalk, increases of 100 per cent have been recorded25. In north-central Texas, where the oil is produced from the Marble Falls limestone, equally pronounced increases have resulted3. The production also in some fields yielding oil from quartz sand cemented with calcitc has been benefited. The evidence of actual increase in total recovery of oil, however, has been questioned by some engineers18. It has been pointed out that the results of the treatment of a well in a now district, where the process has never been tried out, can never be predicted with certainty, since other factors besides percentage of calcareous content of the oil sand play a large part in determining the success of the method. Numerous articles have been published on acid treatment and on the effects of acid on limestone1-35, yet very little has been written concerning experimental work on the actual effect of acid on capillary pores and larger oil-coated voids of oil sands. This is due partly to difficulties in duplicating field conditions in a laboratory and partly to the fact that the process has been carried out largely by contracting companies that have been unwilling to publish details of their results for fear of loss of business to competitors. The authors, using equipment developed to measure the radial permeability of oil-sand cores2', have developed a method of investigating the results of acid treatment which has enabled them to test numerous cores and to study in some detail the action of acid on the different types of rocks, particularly fine-grained rocks.

Jan 1, 1936

By H. l. Burghoff, J. S. Porter

This paper presents the results of an investigation of the effect of cold-working and annealing treatments upon the occurrence of preferred orientation in annealed brass wire. The subject has received less consideration than has the same phenomenon in annealed brass sheet or strip, and perhaps very properly so in view of the obvious and undesired results obtained in the forming or drawing of strip having preferred orientation, which results are in contrast with the lack of any spectacular visual evidence in wire. The factors of cold-working and annealing that control preferredness in strip are naturally expected to function similarly in wire. Indeed, one might expect the condition to be commoner in annealed wire, because the severity of the cold-working between anneals in commercial Practice is usually much greater for wire than for strip. For example, a wire that is to be finished in the annealed condition on a diameter of 0.040 in. is commonly subjected to a final reduction of 90 per cent between the last two anneals, the large reduction being accomplished in the successive drafts of a multiple-die machine. Wire for rivets, for instance, on 0.125-in. diameter, although given a slight reduction of about Io per cent after the final anneal, may have been given a prior reduction of 75 to 80 per cent. Barrettl states the fiber axis of annealed 70-30 brass wire to be [111], with some indication of [IOO] as a secondary fiber axis. Croft and Sachs2 have reported briefly on some differences in brass wire with random and with preferred orientations. They showed statistical plots of the twin-band angles with respect to the wire axis or direction of drawing as observed on an axial plane. They also pointed out that the resistance of the wire to corrosion-cracking when externally stressed and exposed to a mercurous nitrate solution decreased as the degree of the preferred orientation increased. Material and PRocedure All the wire for the investigation was processed from one portion as cut for extrusion from a cast billet of the following analysis: 70.13 per cent copper; 0.01 lead; 0.01 iron; 0.02, nickel; 29.83 zinc (by difference). The billet section, 8 in, in diameter, was extruded hot to 3/4-in. diameter, after which it was processed by alternate cold-drawing and annealing treatments as indicated in Fig. I. The earliest anneals in process were at about 1100°F. and the next to the last reductions by drawing were 58 per cent. The diameter of the finally annealed wire was 0.132 in. Semifinal anneals were at 800°F., 950°F. and 1100°F. and reductions of 47.5, 74, 83.5 and 89.5 per cent were employed in drawing to 0.132 in. The final anneals were at 87s°F., 1050°F. and 1250°F. and were

Jan 1, 1944

By H. l. Burghoff, J. S. Porter

This paper presents the results of an investigation of the effect of cold-working and annealing treatments upon the occurrence of preferred orientation in annealed brass wire. The subject has received less consideration than has the same phenomenon in annealed brass sheet or strip, and perhaps very properly so in view of the obvious and undesired results obtained in the forming or drawing of strip having preferred orientation, which results are in contrast with the lack of any spectacular visual evidence in wire. The factors of cold-working and annealing that control preferredness in strip are naturally expected to function similarly in wire. Indeed, one might expect the condition to be commoner in annealed wire, because the severity of the cold-working between anneals in commercial Practice is usually much greater for wire than for strip. For example, a wire that is to be finished in the annealed condition on a diameter of 0.040 in. is commonly subjected to a final reduction of 90 per cent between the last two anneals, the large reduction being accomplished in the successive drafts of a multiple-die machine. Wire for rivets, for instance, on 0.125-in. diameter, although given a slight reduction of about Io per cent after the final anneal, may have been given a prior reduction of 75 to 80 per cent. Barrettl states the fiber axis of annealed 70-30 brass wire to be [111], with some indication of [IOO] as a secondary fiber axis. Croft and Sachs2 have reported briefly on some differences in brass wire with random and with preferred orientations. They showed statistical plots of the twin-band angles with respect to the wire axis or direction of drawing as observed on an axial plane. They also pointed out that the resistance of the wire to corrosion-cracking when externally stressed and exposed to a mercurous nitrate solution decreased as the degree of the preferred orientation increased. Material and PRocedure All the wire for the investigation was processed from one portion as cut for extrusion from a cast billet of the following analysis: 70.13 per cent copper; 0.01 lead; 0.01 iron; 0.02, nickel; 29.83 zinc (by difference). The billet section, 8 in, in diameter, was extruded hot to 3/4-in. diameter, after which it was processed by alternate cold-drawing and annealing treatments as indicated in Fig. I. The earliest anneals in process were at about 1100°F. and the next to the last reductions by drawing were 58 per cent. The diameter of the finally annealed wire was 0.132 in. Semifinal anneals were at 800°F., 950°F. and 1100°F. and reductions of 47.5, 74, 83.5 and 89.5 per cent were employed in drawing to 0.132 in. The final anneals were at 87s°F., 1050°F. and 1250°F. and were

Jan 1, 1944

By J. Szekely, G. P. Martins

A formulation is given for describing the rate of expansion of spherical bubbles rising in liquids the freeboard of which is evacuated. The computer solution of the resultant differential equations has shown that, for low freeboard pressures (less than about 5 mm Hg), on approaching the free surface the bubbles expand much less rapidly than predictable from equilibrium considerations. In other words, in this region the pressure inside the bubbles will be significantly larger than the static pressure in the liquid corresponding to the position of the bubble. These theoretical predictions were confirmed by experimental work, using two-dimensional air bubbles rising in mercury. The important consequence of these findings is that the expansion of gas bubbles in vacuum degassing operations will be a great deal less than expected from hydrostatic considerations. This would lead to a significant reduction in the available interfacial area and may explain the apparent poor efficiency of many vacuum degassing units. VACUUM degassing as a treatment for liquid steel has gained widespread popularity in recent years; the number of known installations exceeds several hundred at the present time.' Although much information is available on both the thermodynamics of the system and the overall performance of various industrial units, much less is known about the fundamental aspects of the process kinetics.2-4 The basic physical situation common to virtually all vacuum degassing operations is the interaction between gas bubbles (swarms of bubbles) and the surrounding molten metal, held in a container, the freeborad of which is at a low absolute pressure. Once formed (or introduced from an external source) the bubbles will ascend, due to the buoyancy forces, and, during this ascent, a significant increase in their volume will occur. This progressive increase in the bubble volume is due to two factors: a) the continuous reduction in the static pressure acting on the bubble during its rise; and b) mass transfer into the bubble from the surrounding molten steel. In a recent paper Richardson and Bradshaw developed equations5 for describing mass transfer into gas bubbles from molten metals at reduced pressures. However, in deriving these expressions it was assumed that the pressure inside the bubble was identical to the static pressure in the adjacent liquid. In other words, the volume of the bubble was considered to be in equilibrium with the pressure of the fluid adjacent to it. This assumption, thus their analysis presented, was thought to be reasonably accurate for most of the bubble's ascent; however, it was unlikely to be valid in the immediate vicinity of the free surface, held at a low pressure. It was pointed out in the discussion6 that the region close to the surface may be of considerable importance as both the driving force and the interfacial area available for mass transfer are at their highest value here. The ' 'anomalous" behavior of gas bubbles when approaching a free surface at low pressures was recently confirmed in a preliminary investigation by Szekely and Martins. ?1 Here high-speed motion photography was used to study air bubbles rising in a column of n-tetradecane with a freeboard pressure of 0.1 mm Hg. It was found that significant distortion of the bubbles occurred on approaching the free surface; furthermore, the expansion observed was much less than what one could expect from hydrostatic considerations, i.e., factor a previously discussed. It follows from the foregoing that a detailed study of these phenomena would be justified both from fundamental considerations and because of their potential relevance to technology. The purpose of the paper is to present a more realistic formulation for the expansion of a gas bubble approaching a low-pressure region, together with a comparison of the theoretical prediction with experimental measurement. An inert bubble will be considered in the first instance; it is thought that the understanding of the fluid mechanics is an essential first step toward the realistic formulation of the mass transfer process. This latter problem will be the subject of a subsequent publication. FORMULATION The Physical Model. Consider a spherical bubble, of initial radius Ro, rising in a fluid, having a density pL. Initially let the bubble be at a distance H from the free surface, and at a pressure Pgo, as illustrated in Fig. 1. Pgo, the initial pressure in the bubble, is given by the following equation: pgo = Po = Ptp +pLgH [ la] where Po is the pressure in the liquid corresponding to the initial position of the bubble and Ptp is the pressure at the free surface. The fluid pressure at

Jan 1, 1970

By AIME AIME

FREE competition, long the controlling ideal of domestic trade within the United States, has had the fundamental geographical advantage of functioning in the world's largest area of unrestricted commerce. Goods moved back and forth across state lines, unimpeded by customs, and industrial operations have developed rapidly to meet the expanding needs of a pioneer country richly endowed with natural resources. Fifty years ago, antitrust laws were adopted to protect the competitive private enterprise principle. It became illegal for one person to combine with another to restrain trade or commerce among the several states or with foreign nations. The original legislative measures defining this philosophy were the Sherman Act of 1890 and the Clay- ton Act passed in 1914. The development of Europe and other parts of the world was influenced by different conditions which led to a different theory of trade. Here were many small nations, with limited natural resources and a thin market, and they attempted to protect their national economy by tariff walls. International business arrangements for the purpose of diminishing the ups and downs of the more competitive system --crux of the modern cartel operations-seemed a logical device to stabilize production and guard the interests of both workers and consumers. European governments as well as European industrial interests became convinced that if com- petition could be held in bounds the danger of business depressions and un- employment could be reduced.

Jan 1, 1944

By H. 0. HOFMAN AND W. MOSTOWITSCH

I. INTRODUCTION. THE mineral gypsum, CaSO, + 2 H2O, has been used for many years as a sulphurizing and basic flux in several smelting¬operations. Thus, in smelting oxide nickel-ore in the blast furnace, it is commonly added to the charge to furnish the sulphur necessary for collecting the metal in a matte, and a base for slagging the siliceous gangue. In the concentration of lead-copper matte in the reverberatory furnace it has been used for years at Freiberg, Saxony1 for a similar purpose, and for producing at the same time a copper-matte with less than 0.15 per cent. Fe. The latest use gypsum has been put to is in the blast-roasting process of Carmichael-Bradford.2 The term "blast-roasting," given by A. S. Dwight3 to the Dwight-Lloyd method of roasting and agglomerating ,I is a happy generic term which covers the ground better than the " lime-roasting" of Ingalls' or the " pot-roasting " of Austin,6 in that it leaves the operation independent of the character of the flux and the form of apparatus, and retains the characteristic feature of this class of processes-namely, that of using forced draft. In the Carmichael-Bradford process the dehydrated material, mixed with galena-concentrate, acts as a diluent and a flux. The process differs in this from the Huntington-Heberlein7 and the Savelsberg8 processes, in both of which limestone is used.

Jan 1, 1909

By Harry E. Krumlauf

The year 1957 was one of declining metal price and production. Many lead-zinc-copper mines were forced to close, and the remaining mines limited production to stay more in line with demand. High cost of labor, supplies, and equipment and high taxes aggravated the situation. Some operators postponed or abandoned expansion programs because of uncertain economic conditions. Output was curtailed by elimination of over- time employment and reduction of the working force. The number of employes laid off was small- reduction in the labor force was accomplished by not replacing those who left a company's employ.

Jan 2, 1958

By E. O. Wagner, V. F. Parry

This paper summarizes investigations during 1949 on three pilot plants for drying low-rank fine cool by entrainment in hot gases. Detailed operating results on processing seven coals having moisture ranging from 24 to 62 pct, formulas and data for calculating performance of large units, and general conclusions on the problem of drying fine coal are presented.

Jan 1, 1950

By W. G. Frailing, W. P. Sims

The Lakeview Pool of Kern County, California, was discovered in 1910 with the drilling of Lakeview No. 1 which blew out and produced an estimated 8,250,000 bbl of oil in 544 days of uncontrolled flow. The well has since been known as the Lakeview Gusher. Full exploitation of the pool did not take place until about 25 years later. A total of 112 producing wells were completed in the Lakeview sand through April 30, 1949. As of that date, about 30 per cent of the total wells drilled were still producing, with an average pool production rate of approximately 2000 bbl per day. The cumulative oil production was about 41 million bbl of oil, or 55.3 per cent of the tank oil originally in place. The pool is bordered on its down-structure side by a body of inactive edgewater and water production where present has been principally the result of coning. Since the depletion of the greater portion of the gas energy by the Lake-view Gusher, the pool has operated under gravity drive. Relatively high angle dips, good permeabilities and favorable fluid characteristics have made gravity drainage particularly effective. Since January, 1942, the oil recovery -has been relatively constant at about 53,000 bbl per ft drop in fluid level. Correlations between the volume of reservoir space drained and the cumulative oil produced indicate that an ultimate recovery of 63.3 per cent of the tank oil originally in place is attainable. INTRODUCTION The Lakeview Pool is an outstanding example of gravity drainage. It is one of many productive reservoirs of the Midway-Sunset Field, and is located in Kern County, approximately five miles southeast of Taft and two miles north of Maricopa, California. Its position rel- ative to surrounding pools and to the Thirty-Five anticline is shown on Fig. 1. The northern portion of the pool lies in sections 32 and 33, Township 32 South, Range 24 East, Mt. Diablo Base and Meridian, while the southern portion lies in sections 25, 26, 35 and 36, Township 12 North, Range 24 West, San Bernardino Base and Meridian. As no two sections bear the same number, they will hereafter be referred to by section number alone. The purpose of this paper is to review the performance of the Lakeview Pool in an effort to evaluate the effectiveness of gravity drive as a recovery mechanism. REGIONAL STRATIGRAPHY AND STRUCTURE The oustanding structural feature is this area is the Thirty-Five anticline, the axis of which plunges South 75" East through the center of Section 35. As shown on Fig. 2, the following zones are oil and gas bearing in the Thirty-Five anticline area: Pleistocene Basal Tulare Tar Sands Pliocene San Joaquin Mya Sands Top Oil or Scalez Zone Etchegoin Kinsey Sand Wilhelm Zone Gusher Sand Calitroleum Sand Miocene Reef Ridge Lakeview Sand Sub-Lakeview Miocene Sands Monarch Sands or fractured shale equivalent Maricopa Webster Sand or fractured shale equivalent Fractured Shale-Uvigerina Zone C Obispo Sand and fractured shale equivalent Pacific Shale Zone The productive interval of the Lakeview Pool is limited to Upper Miocene and Lower Pliocene deposition. In this general area, the most prevalent type of accumulation results from stratigraphic traps or permeability pinchouts. As is the case of the Lakeview Pool, strati-graphic traps resulting from angular unconformities are present. The structure within the Miocene does not parallel that of the Etchegoin (Pliocene), as the Miocene beds were folded, and in places faulted, and subjected to erosion prior to Pliocene deposition. The Lakeview horizon consists of truncated sands which occur on the northeast flank of the Thirty-Five anticline. The direction of strike is west and northwesterly through sections 25 and 36 and continues northwesterly through sections 26 and 33, to the approximate center of section 32. At this point the strike swings to the northeast and the horizon re-enters section 33. in the northwest corner. The change in strike in section 32 affords synclinal accumulation at that point. The Lake-view sand is truncated updip by the Etchegoin overlap. To the southeast, the sand shales out, while to the northwest, the productive interval appears to be limited by a combination of stratigraphic pinchout and permeability barrier. Structurally, the Lakeview reservoir presents three areas of interest, as shown on Fig. 3. Area I in section 32 is a region in which a productive Sub-Lakeview Miocene sand is present. It occurs from 10 feet to 30 feet below the base of the Lakeview sand and attains a maximum thickness of 25 feet in Well No. 21, section 32. The producing characteristics of the Sub-Lakeview Miocene sand differ radically from those of the Lakeview sand. Water production at high structural locations and abnormally high fluid levels indicate that there was no communication with the Lakeview sand. Wells in Area I penetrated this sand and produced it in conjunction with the Lakeview sand. In Area 11, the Lakeview sand is a

Jan 1, 1950

By David, Levinger

THESE observations of the metal-working industries of Europe are based on a three months' tour of eight countries of Europe, in which 75 industrial establishments were visited in England, France, Germany, Belgium, Holland, Italy, Austria and Switzerland during the summer of 1927. Since the Western Electric Co. is a large consumer of copper and brass, these industries were of particular interest and differences in practices were of keen interest to us.

Jan 1, 1928

By Walter S. White

The Michigan native-copper district has produced about 5,400,000 tons of copper since mining began in 1845. The copper occurs primarily as open-space fillings and replacements in amygdaloidal flow tops and conglomerate beds of the Portage Lake Lava Series, of middle Keweenawan age. Secondary minerals with which the copper is associated include microcline, chlorite, epidote, pumpellyite, prehnite, quartz, and calcite; zeolites, other than laumontite, are not abundant. A zonal pattern of the secondary minerals transects bedding and suggests regional metamorphism mainly to the grade of the prehnite-pumpellyite graywacke facies of Coombs. Most of the major copper deposits are near the upper limit of abundant quartz in this zonal pattern. The distribution of copper in both amygdaloid and conglomerate deposits is controlled partly by primary permeability of the rocks and partly by later tectonic fracturing that was concentrated in the mechanically weak flow tops and sedimentary beds. Ore shoots and deposits are therefore controlled partly by primary structural features, such as areas of thick and thin fragmental amygdaloid or the boundaries of conglomerate lenses, and partly by regional structure: a number of ore deposits are in synclinal downwarps. The copper-bearing solutions that formed the deposits were ascending. They may have come from a large concealed intrusive, or may have been driven out of the porous tops of lava flows when the rocks were compacted and metamorphosed at great depth in the central part of the Lake Superior syncline. The second hypothesis seems more consistent with the widespread distribution of the copper, its relation to mineral zoning that represents truly regional metamorphism, its native state, and the likelihood that copper deposition was later than most or all of Keweenawan volcanism.

Jan 1, 1968

By Charles Albert Ashburner

The coal-fields of the United States have been variously classified as to their geographical positions. In 1887 I proposed slight changes to the classification generally used, for more convenient description of our coal-fields in my report on the statistical history of coal in the States during 1886 for the United States Geological Survey. This new classification seems to meet all practical requirements and has been generally adopted. The coal-areas are grouped in two divisions—the anthracite division and the bituminous division. The anthracite division, in a commercial sense, may be said to include the anthracite districts of Pennsylvania alone, although small amounts of anthracite are mined in Colorado and have been

Jan 1, 1890

By A. C. Fraker, H. H. Stadelmaier

In the systems Mo-Fe-C, Mo-Co-C, and Mo-Ni-C the phase boumdaries of the cubic Ij carbides were determined at 1000°C and the variation of the lattice parameter with composition was measured. In the system Mo-Fe-C a single ternary carbide, Mo3Fe3C, was observed. In Mo-Co-C and Mo-Ni-C two new n phases of the type M12C were found: Mo6C06C and Mo6Ni6C. At 1000°C they coexist with the M6C phases MO3-4,CO3-2C and Mo3-4Ni3-2C, respectively. Mo3C03C and Mo4C02C are not separate phases but parts of a single M6C phase region, and the same is true of Mo3Ni3C and Mo4Ni2C. THE n carbide structure type has been known since it was determined by westgren' in 1933, yet reliable information on phase compositions of this type is ap-parently scarce. The following selection of suggested formulas illustrates the extent of the confusion con-cerning compositions: W2-3Fe4-3C,1W6Fe6C,2 W2_4Fe4-2C,3 (W,Fe)6C,4 Tj.-W4Co2C and nz-W6Co6C,5 n1-W3Co3C and n2-w4Co2C,5 W3C03C and w6Co3C2,7 MO3Fe3C,8n2-M04Fe2C,9 (MO,Fe)6C,4 MO3CO3C,8 n2-MO4CO2C.9 Many of these compositions obviously overlap, some disagree in carbon content. The use of the designations 77, and n2 is not consistent. There is uncertainty whether two carbides M6C coexist or whether there is only one M6C with a wide range of substitution of one metal for the other. The existence of M12C seems questionable altogether if one ignores the results of a neutron diffraction study of W6Fe6C supporting that particular metal to carbon ratio.'' More reliable information is available for the iso-typic oxides studied by Nevitt,11 Nevitt, Downey, and orris," and Meussner and carpenter.l3 That n car-bides and oxides are structurally identical, particularly with respect to the location of the metalloid atom, has been demonstrated clearly by Stadelmaier and Meussner14 and also by Parthe, Jeitschko, and sadagopan.15 Therefore the present paper, which attempts to establish the phase boundaries of n defini-tively for three carbon systems, has implications for the whole family of filled Ti2Ni types. EXPERIMENTAL PROCEDURE The samples were prepared in two stages. Pellets weighing 3 g were compacted from powders of the elements and presintered in a closed tube of fused silica that had been evacuated to lO-4 mm Hg. This was fol- lowed by arc melting the sintered samples under argon. Remelting the button once was sufficient to produce homogeneous specimens. The metal powders had the following minimum purities in wt pct: molybdenum 99.5, iron 99.0, cobalt 99.7, nickel 99.9, graphite 99.94. Carbon determinations by the gas volumetric method were obtained from thirty-one of the one hundred samples in the annealed condition. They were limited to compositions that were critical to placing a boundary line in the isothermal sections. The carbon losses were comparatively low and averaged less than 1.5 at. pct. For annealing, the samples were sealed in tubes of fused silica evacuated to 10-4 mm Hg. The annealing schedule was 20 hr at 1250°C followed by 150 hr at 1000" ±10°C. For the water quench the silica glass tubes were broken mechanically to speed the quench. The specimens were examined in the as-cast and annealed condition by standard metallographic techniques. Some of the as-cast and all annealed samples were studied by X-ray diffraction using a 114.6-mm powder camera with filtered Co radiation. The lattice parameters of the n phases were determined by graphic extrapolation to 8 = 90 deg on a plot against sin2 8. It is estimated that the maximum error in the lattice parameters is ±0.002A.. The phase fields were determined by the disappearing phase method, relying on X-rays for phase identification and on microscopy to detect small amounts of a phase. RESULTS Pertinent information on the binary side diagrams has been summarized by Hansen and Anderko16 and Elliott17 and will not be discussed further. Photomicrographs documenting the equilibria at 1000°C have been selected to avoid redundancy due to the similarity of the three systems. Thus there will be only one picture showing an equilibrium with Mo2C, and so forth. Molybdenum-Iron-Carbon. An isothermal section of most of the Mo-Fe-C system at 1000°C is shown in Fig. 1. No attempt has been made to distinguish between a and y iron or to determine their phase boundaries. A conspicuous absence is the phase Fe2 1Mo2C6 with the Cr23C6 structure, supporting the suggestion by Krainer4 that it decomposes by annealing at high temperatures. The only ternary phase is found in a narrow range around Mo3Fe3C (MO43Fe43C14). A microstructure with a two-phase mixture of Mo + n is seen in Fig. 2. The variation of the lattice parameter of n with the estimated composition is shown in in Table IA. The phase diagram does not agree with the results of Kuo9 who reported n2-Mo4Fe2C. Our lattice parameter Varies from 11.095A at the iron-rich end to 11.140Å at the molybdenum-richoend of the phase field whereas Kuo9reported 11.26Å for Mo4Fe2C. We are in agreement with the older work

Jan 1, 1970

By Westwater, J. S.

The Mather mine of The Negaunee Mine Co. embraces nearly all of Sections 1 and 2, T47N, R27W. within the limits of the cities of Negaunee and Ishpeming on the Marquette iron range of Michigan's Upper Peninsula. Operations of the Negaunee Mine Co., the stock of which is jointly owned by Bethlehem Steel Co. and The Cleveland-Cliffs Iron Co., are under the direction of the latter company. The opening of the Mather mine was described by C. W. A1len. Mather "A" shaft was completed to an initial depth of 2352 ft in early 1943. The shaft capacity of over one million tons yearly is in prospect of being realized by orderly development and mining, and sinking of the second or "B" shaft then started in accordance with previous planning. Mather " B, " also a vertical shaft, was designed as a twin to Mather "A" shaft and the sinking technique developed at Mather "A" was utilized in "B" shaft operation.

Jan 1, 1949

By E. A. Anderson

THIS seems to be the year for superlatives in A.I.M.E. meetings. The programs of the various Divisions and Institute committees offered an abundance of interesting and valuable information in the form of technical papers, symposia. and lectures to large and interested audiences. The Institute of Metals Division may hold up its head with pride for its own program. With six technical sessions, three full-day symposia, and the annual I.M.D. dinner, four meeting days were not enough and many simultaneous sessions were required. The quantity and quality of the paper were equaled by the numbers and interest of those attending.

Jan 1, 1944

By Andrews Allen

WE all remember when, a few years ago the preparation of coal was nothing but a matter of having somebody at the face or somebody in the railroad car pick out the impurities; also the sizes were generally' made" over a bar screen. Anything that was black was coal; and the only matecia1 picked out was the slate or rock-impurities that could be distinguished by eye or by hefting. This was all right as long. & coal could be sold at. a good price. After all, we are all in business to -make the most money honestly out of a certain acreage of coal and a certain plant. For this purpose what is required is the greatest possible recovery of marketable coal and the highest market price.

Jan 1, 1929

By Frederick G. Tickell

GEOLOGISTS have been quick to adopt new methods in locating new oil fields and in finding the extensions, laterally or at depth, of the old fields. For most of these new methods he is indebted to the physicist, the engineer, and the chemist, although he has also drawn from such ordinarily unrelated sciences as bacteriology and protozoölogy. These last-named sciences have been of help in problems dealing with the origin of petroleum and, although not of direct application to oil finding, have furnished evidence of value in learning what oil is made from and what are the natural agencies involved in its formation.

Jan 1, 1932

By David C. N. Cockburn

INTRODUCTION This paper analyses certain of the financial considerations which will commonly apply in relation to the following questions: - what equity structure or project vehicle should be adopted for the exploration and/or exploitation of a project by more than one unrelated participant? - what vehicle should be adopted by a participant for its participation in a multiparty project? Due to local, politically motivated laws in certain jurisdictions, or due to the overriding requirements of a dominant participant, there may be little choice of the underlying multiparty structure which may be adopted for the exploration, appraisal and/or development phases of a project. Nevertheless, even in such circumstances, attention should be given, at least in the preparation of the related documentation, or in considering methods of participating or funding the project, to certain of the points discussed below. This discussion of financial considerations in the context of the more commonly adopted multiparty structures concentrates primarily on fiscal, financial accounting, financing and funding aspects. TYPES OF PROJECT VEHICLE FOR MULTIPARTY INTERESTS The well known types of vehicle adopted for the participation in a project by more than one participant (assuming that the participants are effectively unrelated) are as follows. Joint Venture (unincorporated joint venture) By far the most commonly adopted structure for mining ventures, a joint venture is usually defined and documented in terms to distinguish it from a partnership for important tax and legal reasons. In essence, this is a contractual association of more than one participant to carry out a specific commercial project or purpose. The relationship between the separate participants and their respective rights, interests, obligations and liabilities are agreed between the participants in one or more contracts (viz Joint Venture Agreements or Joint Operating Agreements together with ancillary documentation). Unlike other project vehicles of participation, in most jurisdictions there is no specific body of law governing joint ventures. The participants thus enjoy contractual freedom to negotiate whatever deal they may wish between themselves. Jointly-Owned Project Company (corporate joint venture) A very familiar vehicle, this is a separate and distinct legal and tax entity incorporated under the company laws of the place of incorporation to undertake specific objects, and granted specific powers, in relation to the Project. Although certain rights, interests and obligations may be circumscribed in the governing corporate instruments by the promoter participants, the corporation laws of the relevant place of incorporation, and the selection of such governing laws (assuming freedom of choice) and future political changes in such corporate laws, should be carefully considered. The use of a company in a multiparty structure may be peripheral to the project itself as a specific purpose vehicle (for example, a joint sales agent or marketing company or a joint borrowing vehicle) or it may form a central function such as in the case of a tolling company which will own the project for legal and taxation purposes and raise financing with the backing of the shareholder participants commonly by the adoption of take-off, throughput and/or user agreements. Partnership This is a legal relationship, subject to the often wide-sweeping restrictions of the relevant local partnership laws, under which the participants have agreed to carry on a business venture together with a view to profit. The effect of the relevant partnership laws, as well as the various types of partnerships and the

Jan 1, 1985