Search Documents

By E. H. Jr. Dix

A LACK of experimental data illustrating the effect of composition, particularly in respect to impurities, on the mechanical properties and corrosion resistance of aluminum-alloy die castings induced the authors and their associates to undertake a limited study of these relations. A number of commercial alloys .and several experimental variations of a commercial alloy were used for the investigation. Mechanical property, growth, steam, paraffin, salt spray and atmospheric exposure tests were employed. This paper deals with the more accelerated tests and the results they have produced. It is concluded that a high-silicon alloy with all impurities except iron strictly limited to small amounts will develop an excellent resistance to corrosion and retain satisfactory mechanical properties and casting characteristics. As a direct result of this investiga-tion an alloy of this character with superior corrosion resistance is now available commercially. In general, copper increases the strength and decreases the elongation and corrosion resistance. Tin reduces the mechanical properties and the resistance to corrosion. Iron reduces the elongation and, if excessively high, may adversely affect the tensile strength. Even excessively high iron contents do not affect the corrosion resistance, which is fortunate for the die caster as it is this element that is the most difficult to control. Nickel and zinc in limited amounts do not seem to affect the properties or corrosion resistance of at least the high-silicon alloy. Growth tests have confirmed the previous common belief that dimensional changes under either dry or wet conditions at 100° C. are too small to be of practical importance.

Jan 1, 1935

By ALBERT P. J. BORDEAUX

THIS paper briefly describes the general outline of cyaniding silver-ores in Mexico, with special reference to personal experiments made in the Temascaltepec district. The most important papers on the subject deal with cyaniding gold-silver-ores, the gold predominating in value, so that the treatment is nearly the same as for gold-ores, the losses of silver being considered of little importance. I describe here the treatment of silver-gold-ores containing very little gold, which is more general in Mexico than elsewhere. The cyanide treatment, which was so successfully applied to gold-ores, did not succeed immediately with silver-ores on account of their varying composition. Gold occurs in nature usually in the native state, while silver occurs generally in combination with sulphur (argentite), and various combinations of sulphur, antimony, and arsenic. In former times there was a complete difference in the treatment of gold-ores and silver-ores. Amalgamation, which was successful with gold-ores, was generally inadequate with silver-ores. The usual treatment in Mexico for silver was the patio process, the theory of which was satisfactorily explained only quite recently by Mr. Ortega and others. GENERAL OUTLINE OP THE CYANIDE TREATMENT. The general tendency of the present practice is to slime the silver-ore as much as possible, and in order to obtain a higher efficiency, with less loss of cyanide, and greater speed, the following lines are observed 1. Crushing by stamps with 30- or 40-mesh screens, then crushing by Huntington or Chilean mills, through 60- or 80-mesh screens. 2. Concentration upon vanners.

Jan 1, 1910

By Eugene Holman

UINQUESTIONABLY the petroleum industry not only can supply the world's present oil requirements but even can meet a considerable increase in demand if it should come. The United States produced last year 1 1/3 billion barrels of crude oil, or more than 60 per cent of the world's total. It could have provided more, if needed, because we has a large shut-in crude producing capacity. Our refining capacity of 4,500,000 0 barrels per day is more than 2 per cent above our average refinery run for 1940. Adequate crude supplies and manufacturing facilities also exist outside of the United States. Large crude reserves exist in South America, in Iran and Iraq, in Russia and Romania, in Sumatra and adjacent islands. The refineries of the Dutch West Indies, of Iran, and of the Netherland East Indies are well located in relation to crude reserves and world trade lanes. Furthermore, flexibility in the manufacturing facilities permits adjustment of yields to meet a considerable range in variations between demands for products. Only with regard to 100-octane aviation gasoline is there any apparent refinery problem. Even here so far as this country is concerned, additional refining facilities can be installed well within the time that would be required to turn out the airplane engines which will use this super fuel.

Jan 1, 1941

By Charles Pack

EXTENSIVE progress has been made in the metallurgy of alloys for die castings. Enthusiastic proponents of some alloys are inclined to make extravagant claims for their materials, which may be justified by physical tests on test bars made from the respective alloys but are seldom justified by the results obtained with commercial die castings made from those alloys. Chemical analysis of the test bars and castings fails to determine the cause of these variations, since they are due to other physical factors entering into the commercial production of die castings. In this paper, an attempt will be made to outline some of the factors in commercial die-casting practice to which these variable results may be attributed, in the hope that the manufacturer of die castings, recognizing the importance of these factors, will devote more attention to them in the design and construction of dies and equipment. In 1914,1 the author defined die castings as "metal castings made by forcing molten metal, underpressure, into metallic molds or dies." This definition was given in order to differentiate die castings from other molded metal products such as "permanent-mold" castings, "slush" castings and similar products that are sometimes erroneously termed die castings. The term "die casting" could be interpreted to include all castings made in metal molds or dies; but since this term, like most of our technical nomenclature, has been developed by commercial practice we must look to this practice for its proper definition. The Germans, with their usual devotion to descriptive names, have adopted the name of spritzguss (squirt cast) for die castings. Undoubtedly this name is more descriptive of the die-casting process, where the metal is literally squirted into the die and serves to differentiate this process from other metal mold processes, where the metal is poured into the die. In the earlier paper mentioned, the author also emphasized the fact that the definition given for die castings indicated clearly that the satisfactory operation of the process must comprise three factors, all of which must be considered of vital importance to the successful operation of the die-casting process:

Jan 1, 1930

By Charles Pack

Extensive progress has been made in the metallurgy of alloys for die castings. Enthusiastic proponents of some alloys are inclined to make extravagant claims for their materials, which may be justified by physical tests on test bars made from the respective alloys but are seldom justified by the results obtained with commercial die castings made from those alloys. Chemical analysis of the test bars and castings fails to determine the cause of these variations, since they are due to other physical factors entering into the commercial production of die castings. In this paper, an attempt will be made to outline some of the factors in commercial die-casting practice to which these variable results may be attributed, in the hope that the manufacturer of die castings, recognizing the importance of these factors, will devote more attention to them in the design and construction of dies and equipment. In 1914,l the author defined die castings as "metal castings made by forcing molten metal, under pressure, into metallic molds or dies." This definition was given in order to differentiate die castings from other molded metal products such as "permanent-mold" castings, L'slush" castings and similar products that are sometimes erroneously termed die castings. The term "die casting" could be interpreted to include all castings made in metal molds or dies; but since this term, like most of our technical nomenclature, has been developed by commercial practice we must look to this practice for its proper definition. The Germans, with their usual devotion to desecriptive names, have adopted the name of sprilzguss (squirt cast) for die castings. Undoubtedly this name is more descriptive of the die-casting process, where the metal is literally squirted into the die and serves to differentiate this process from other metal mold processes, where the metal is poured into the die. In the earlier paper mentioned, the author also emphasized the fact that the definition given for die castings indicated clearly that the satisfactory operation of the process must comprise three factors, all of which must be considered of vital importance to the successful operation of the die-casting process:

Jan 1, 1931

By Thomas E. Leontis

INTRODUCTION THE importance of magnesium alloys in the manufacture of aircraft engines has been realized for many years. A concentrated effort has been exerted in the laboratories of the Dow Chemical Co. to develop magnesium-base alloys with improved properties at elevated temperatures whereby greater advantage can be taken of the inherent lightness of these materials. In an earlier publication,1 attention was called to the superior tensile properties and resistance to creep of cerium-containing magnesium alloys at temperatures up to 700°F. More recently, additional data on magnesium-cerium alloys have been furnished by Murphy and Payne.2 The present paper deals with the mechanical properties of sand-cast magnesium alloys containing zinc, at temperatures up to 500°F. The study includes binary Mg-Zn† alloys containing up to 10 pct zinc and several ternary and some polynary alloys based on the Mg-1Zn,†Mg-3Zn, Mg-4.4Zn, Mg-6Zn, and Mg-10Zn binaries. The compositional variation in the tensile properties, hardness, and creep at room and elevated temperatures, and in the electrical conductivity at room temperature has been determined. The results of these tests show that many zinc-containing magnesium alloys exhibit resistance to creep at elevated temperatures significantly higher than that of present commercial magnesium alloys, but lower than that of alloys of the magnesium-cerium type. In addition, they have high tensile properties at room and elevated temperatures and high conductivity. This combination of mechanical properties and conductivity indicates that these alloys should be given serious consideration for commercial applications involving exposure to temperatures higher than those to which present commercial magnesium alloys can be taken safely. LITERATURE The properties of sand-cast magnesium alloys containing zinc as a principal alloying element have not been investigated very extensively, especially at elevated temperatures. The following remarks, which are confined to sand-cast alloys, will serve as a summary of the most important references on this phase of magnesium metallurgy. The first recorded determination of the tensile strength of binary Mg-Zn alloys as a function of zinc content was reported by Aitchison.3 Similar studies, including the measurement of elongation and hardness, have been performed by Gann and Winston,4 Dumas and Rockaert,5 Haughton and Prytherch,6 and by Spitaler, the last being reported by Beck.7 A slight superiority in the tensile strength of chillcast Mg + 8 Zn alloy over the sand-cast alloy was noted by Maybrey 8 That alloys of magnesium containing 5 to 12 pct zinc

Jan 1, 1948

By Walter Fuchs

It is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established.23 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2:I for the combined effect of both factors, as compared to the exclusive effect of either one, if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. Synopsis of Biological and Chemical Facts The biosphere is not sterile; i.e., microorganisms are always present. Microor- ganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life—proteins, fats, carbohydrates, lignins, waxes, resins— may serve as a habitat of microorganisms. In the decomposition of a medium, some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate.17,32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1942

By Walter Fuchs

It is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established.23 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2:I for the combined effect of both factors, as compared to the exclusive effect of either one, if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. Synopsis of Biological and Chemical Facts The biosphere is not sterile; i.e., microorganisms are always present. Microor- ganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life—proteins, fats, carbohydrates, lignins, waxes, resins— may serve as a habitat of microorganisms. In the decomposition of a medium, some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate.17,32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1942

Jan 1, 1879

By Charles E. Heinrichs

IN the last decade one of our oldest and largest non-metallic metallic mineral industries has been the subject of persistent technical research, the results of which are another example of the benefits following the systematic application of scientific principles. The consequent improvement in the technique of phosphate recovery represents the greatest material advance in the industry since the discovery of phosphate in Florida in 1881. Moreover, these successes have stimulated interest and development in numerous other nonmetallic industries. Strange as it may seem, and despite the fact that the phosphate deposits of Giles County, Tennessee, together with those of Polk and Hillsborough Counties, Florida, have yielded more than 50,000,000 long tons in the last twenty years, the mineralogy of phosphates has been given scarcely any space in our technical literature. For many years it was the general consensus that these so-called phosphate rocks represented a physical mixture composed principally of tri-calcium phosphate, together with smaller quantities of calcium carbonate, calcium fluoride, iron phosphate, aluminum phosphate and other less important constituents. More recent investigations, however, led to the conclusion that these phosphates really represent a complex mineral in which calcium, iron, aluminum, phosphorus pentoxide, carbon dioxide, and fluorine all form a definite part of the molecule. Colony, after a careful study, utilizing chemical, microscopic, and X-ray diffraction methods, reported that American phosphates consist principally of calcium-carbono-phosphate of the staffalite type.

Jan 1, 1933

By R. E. Hudrlik, G. W. Preckshot

The diffusion coefficients of silver from solid silver in molten lead were measured to within ± 0.8 pet in a columnar type diffusion cell ower, the temperature range of 326° to 530°C. Fick's law describes the process up to 530°C where the laminar mechanism appareltly breaks down. These is negligible resistance at the interface as shown by mathematical analyses. The diffusion coefficients are found concentration independent. IT would seem that diffusion in liquid metals would be free of such effects as molecular structure, dissociation. polarization. and compound formation. This view was taken by Gorman and preckshot in their study of diffusion of copper from solid copper into molten lead. They reported diffusion coefficients which were independent of the concentration over the range of 478° to 750°C. They found that the Stokes-Einstein equation with constant radius of the diffusing specie represented the diffusion data better than Eyring's rate theory equation and Sheibel's correlation. The radius of diffusion was found to be that of the doubly charged copper. There appeared to be no resistance across the solid-liquid boundary. In the present work the diffusion coefficients for silver in liquid lead were measured over a range of temperatures of 350° to 505°C. The solubility of silver in lead over the range of 303° to 630°C was also obtained. These results are compared with calculated or correlated values or with data in the literature. EXPERIMENTAL Procedure—The experimental equipment techniques and procedures were those reported in detail by Gorman and preckshot9 and will not be repeated here. Measured values of WT, Co, A. L were obtained for various diffusion times and the diffusion coefficient was computed for the case of no resistance at the interface9, 11 by: WT/CoAL = 1- 8/p2 n=1 1/(2n - 1)2 exp[-(2n - 1)2p2 Dt/4L2] [1] or where there was resistance at the interface by: WT = 1- ?n=1 2h2/ap2L [sxp [-Dan2t]/[(h2 + an2) L + h] The roots an are those of the transcendental equation3 tan (an L) = Iz/cun. The diffusion coefficient is that defined by Hartley and Crank.7 The total silver in the lead cylinder and equilibrium slug was determined by a cupellation technique' with proper correction for losses. Analysis of known samples showed that this method is surprisingly accurate. The amount of silver in the lead adhering to the silver cylinder was obtained in the same fashion as shown by Gorman and preckshot.9 The small errors involved in this determination are not critical since the silver in this adhering lead layer is only 3 to 15 pet of the total diffused. Materials—Electrolytic silver containing 99.9+ pet Ag obtained from General Refineries of Minneapolis, Minn. was used for all but runs 7 and 8. For the balance of the runs this silver was reduced with hydrogen at 1100°C and its oxygen content was found to be about 0.017 pet. For the runs. 7 and 8, phosphorous-reduced silver of the same purity was obtained from Handy and Harman Co. of Chicago, Ill. The densities of the phosphorus-reduced silver and the hydrogen-reduced electrolytic silver were 10.484 and 10.487 g per cm3, respectively. These values agree with those reported for pure silver. Silver which was reduced at 900 C had an average density of 9.998 g per cm3, indicating porosity. This silver was used for a number of runs which were not tabulated in Table I. These are indicated by crosses on Fig. 2. The 99.999 pet Pb was obtained from the National Lead Co. Research Laboratory of Brooklyn, New York. DISCUSSION OF RESULTS The diffusion and solubility results are reported in Table I for eleven runs using either phosphorus-reduced electrolytic silver or hydrogen-reduced silver at 1100° C. The solubility data shown in Fig. 1 show the excellent agreement with that reported by Heycock and Neville.8 The data of Friedrichs5 apparently are in error. The experimental solubility data of this work are reported to 0.3 pet. The experimental diffusion coefficients computed from Eq. [1] are reported within 1.2 pet of the mean and are plotted in Fig. 2. These are expressed within +0.8 pet of the experimental values over the entire temperature range by: D= 8.26 x 10 -5 e-1925/RT . [3] There appears to be little difference due to the

Jan 1, 1961

By Joseph R. Hatch

When compared to average shale composition, average coal is enriched in sulfur and selenium, has similar amounts of arsenic, beryllium, lead, antimony and molybdenum, and is depleted in at least 26 other elements. Within a coalfield, or region, some coals are enriched (10X average shale) in silver, arsenic, cadmium, cobalt, germanium, molybdenum, nickel, lead, selenium, uranium, and zinc. Important factors controlling element distributions in coal include geochemical conditions (primarily pH) in the peat swamp, composition and depositional environment of coal roof rocks, thermal maturity (rank), nature and intensity of any epigenetic mineralization, composition of ground waters that come in contact with the coal, and degree of weathering.

Jan 1, 1983

By H. K. Shearer

Drilling for oil and gas in Arkansas in 1934 showed more activity than in any year since 1929; with a total of 96 completions, including 36 oil wells, 1 gas well and 59 dry holes. Of the producers, the lone gas well and 35 oil wells were in old fields, and one wildcat producer opened a new pool. Of the dry holes, 16 were in or near fields and 43 were wildcats. The total reported initial daily production of the oil wells was 9013 bbl., averaging 252 bbl. per well. Active drilling operations numbered 65 at the close of the year, compared with 26 at the beginning.

Jan 1, 1935

By A. N. Rogers

Jan 1, 1883

Jan 1, 1968

New York State Museum, Albany, N. Y. D H. Newland, State Geologist. A complete list of publications or the latest lists of available publications will be sent upon application. A series of Bulletins on The Mining and Quarry Industry of New York are available as follows: Bulletin 51 (1910), 15 cents; 161 (1911), 20 cents; 166 (1912), 20 cents, 174 (1913), 20 cents; 190 (1915), 15 cents; 277 (1925-26), 50 cents; 295 (1927-1929), 40 cents. Another series discusses the Geology of the State by Quad¬rangles, available as follows: Bulletin 153, Broadalbin Quad (1911), 25 cents; 154, Sche¬nectady Quad. (1911), 20 cents, 170, North Creek Quad . (1914)

Jan 1, 1933

By B. Egeberg

IN A previous paper1 the authors dealt with the physical properties of cold-rolled and heat-treated Britannia metal of the approximate composition Sn, 91 per cent., Sb, 7 per cent. and Cu, 2 per cent. It was found that cold rolling to more than 50 per cent. reduction produced a continuous softening of the metal when measured by the Brinell machine, whereas the Shore instrument indicated increased hardness; that the strength of the material followed the Brinell hardness and that the metal therefore became weaker the more it was cold-rolled; and further, it was found that hardness and strength could be largely restored to the cold-rolled metal by "baking" for about one hour at any temperature, between 200° and 450° F., the melting point. The higher the baking temperature, the more effective was the heat treatment as far as increased hardness was concerned. It seemed to be of little importance whether the metal was soaked or not at the baking temperature for a great length of time and the rate of cooling seemed to be immaterial. The present paper deals with the same alloy and more particularly with the resistance towards various forms of stress - tensile, bend and deep drawing. The metallography of Britannia metal has in part also been covered and an explanation attempted for the abnormal behavior of this alloy.

Jan 1, 1929

By AIME AIME

T HE Institute of Metals Division and the Iron and Steel Division will meet jointly at the Stevens Hotel, Chicago, during the week of the American Metals Congress, Sept. 22-26. The Iron and Steel Di- vision of the American Society of Mechanical Engineers, the American Society for Steel Treating and the American Welding Society meet at the same time. but the sessions have been arranged to conflict as little as possible. A rich program of papers and plant visits has been arranged for the members and guests of the two Institute Divisions. The annual dinner and a pro- gram of entertainment are being arranged by the Woman's Auxiliary of the Chicago Section. Members are urged to register immediately up011 arrival and to make dinner and plant visit reservations at the same time.

Jan 1, 1930

THE members arrived at Ticonderoga, N. Y., at noon, Tuesday, October 15th, and were received by Mr. Cyrus Butler, Chairman of the Local Committee of Arrangements. During the afternoon the works of the American Graphite Company and the Horicon Iron Company were visited under the guidance of Mr. Butler, President of both companies, and of Mr. William Hooper, Superintendent. An excursion was then made, in carriages, to old Fort Ticonderoga, on Lake Champlain, after which the party were driven to the Rogers Rock Hotel, on Lake George. The first session of the Institute was held in the parlor of time hotel on Tuesday evening. Mr. Eckley B. Coxe, President of the Institute, opened the proceedings with the following address: I shall ask your attention, this evening, to a few reflections upon the subject of mining engineering as a profession in the United States, its past, its present, and its future, and its duties and oppor¬tunities with reference to the proper development of our great min¬eral resources. Thirty years ago, there were scarcely any mining engineers in this country, and but few in England, and there were no institutions where young men could be educated for the profession in the Eng¬lish language. France and Germany have been able for about a century to boast of mining schools of a high character, that number among their graduates such men as Humboldt, Weisbach, Rittinger, Combes, and Gruner. Of the few we then had worthy of the name of "mining engi¬neer," some had studied in the continental academies, and others were graduates in the school of practical experience, and had learned their profession in mines and smelting-works. Their work con¬sisted principally in making surveys and maps of mines and mining properties, geological reports, and analyses of ores ; but the mining engineer whom we often meet with now, who has studied chemistry, physics, mineralogy, geology, mechanics, and drawing; who is more or less familiar with machinery and its construction, and with the practical management of mines or smelting-works, and who is an expert in some one branch of his profession, would have been very difficult if not impossible to find in the United States. The induce¬ments held out to ambitious and talented young men to enter the

Jan 1, 1879

By C. M. Haight

The mines of the New Jersey Zinc Co. in New Jersey, are situated in the northern part of Sussex County, at Franklin, formerly Franklin Furnace, and also at Ogdensburg. The mine at Ogdensburg is still in the development stage, but the, mine at Franklin, with which this paper deals chiefly, has been a steady producer of high-grade zinc ores for many years. The town is about 50 miles from New York City, among the foothills -of the Kittatinny Mountains. It is equipped with water supply (filtered and chemically treated), good roads, electric lights, efficient police protection and excellent schools, including a new vocational high school. For a mining community, the conditions and location are far above the average. Franklin Furnace Folio, No. 161 of the U. S. Geological Survey, describes the geology and mineralogy of the district in detail, so that merely an, outline of the main characteristics of the orebody need be given. The

Jan 10, 1917