Search Documents

By A. M. Hearn, J. R. Henning, A. S. J. Van Rensburg

The lining, together with the electrodes, forms the heart of the operation of a submerged arc furnace. Subsequent to a lining failure on M12 furnace during the early 1980s, Metalloys was active in investigating the concept of thermally efficient ?freeze? linings for its furnaces. The theory revolved around that, not only would, thermally efficient linings result in significant cost savings, but they would also last longer as a result of being subjected to less harsh operational conditions. After having proved the concept on the .smaller. furnaces, Metalloys decided to implement the concept on its largest submerged arc furnace, M12 Subsequent to having recovered from an impending failure of a lining installed in 1981 in M12 in the mid 1980s, Metalloys managed, through rigid lining management, to extend the life of this lining to 1999. At the end of 1999 the decision to replace the lining in the furnace with a ?freeze? lining was made and planning and design proceeded in earnest. This paper discusses the options considered in making the final decision. The features of the design of the lining are also discussed. Consideration is given to the furnace shell cooling system as a result of its importance in maintaining the thermal equilibrium in the lining. Note is made of the fact that the purchase of a .freeze. lining is an expensive exercise but that the time savings in the installation of the lining and the efficiency improvements during operation far outweigh the additional capital cost. The experience on M12 has been that the payback period of the marginal capital expenditure is less than three years. As a result of the opportunity to reline a furnace the size of M12 not presenting itself very often, the learning points from the installation of the lining and the operational advantages and disadvantages are significant. Finally, the point is made that the project had its pros and cons but overall the success of the project has been evident and, as such, the ?freeze? lining is likely to become the norm at Metalloys.

Jan 1, 2004

By J. Greenspan

The anisotropy of fracture and slip, that is, the brittleness and ductility of the beryllium single crystal, is characteristic also of po1ycrystalline beryllium in which the grains are oriented in a preferred manner. Beryllium with grain orientations resulting from hot working either unidirectionally or bidirectionally is ductile or brittle in directions given by the anisotropy and orientation of the grains. Textures developed from various hot-working sequences are given, and tensile results are correlated with textures. Not only texture, but fine grain size is necessary for obtaining high tensile elongation. Ultimate tensile strength and elongation are both correlated with grain diameter. Of particular interest is the case in which unusually high tensile elongations of 30 to 40 pct are obtained when basal planes are oriented to carry THE beryllium crystal (of nominal purity) is probably unique among metals with respect to its unusually acute anisotropy of slip and fracture. While extensive slip can occur on the system (1010) [ll20] starting at about 19,000 psi, the (0001) plane is particularly vulnerable to fracture at 4500 psi or less. Fracture occurs also on the (11zo) plane at about 26,000 psi.1"3 Further, there seems to be no other slip System which contributes significantly to

Jan 1, 1960

By Arnold O. Tanner

The recession that took hold of the domes-tic mining industry in 1981-82 finally abated somewhat in 1987, resulting from increases in many commodity prices, especially in the metals sector, and from continuing success in lowering operating costs. By no means was the work finished; the mining industry was in a sense entering a new era. The struggle for survival was still very evident for many companies and various commodities, but increasing productivity and profits were accompanied by indications that these trends were more long term than short term. Raw nonfuel minerals produced in the United States during 1987 had an estimated value of $26.3 billion, an increase of $2.9 billion over the 1986 value. This is the fifth consecutive year that the value has increased. Except for a decrease in 1982, the value each year has increased since 1971, or 15 of 16 years. The value of raw metals production increased by an estimated 28%, an impressive improvement since the drastic fall in 1982. Industrial minerals growth was comparatively flat, with an estimated in-crease in value of 0.1 %, continuing a trend of the previous 2 years. Metal mine production dropped considerably in 1982 and maintained its resultant lower level until 1987, when production significantly recovered.

Jan 1, 1989

By F. L. Wideman

This report describes a computer program that is used for the calculation of the coordinates and elevations of subsidence survey pins located by intersection. This program was developed for the Federal Bureau of Mines by the Numerical Analysis Laboratory, University of Arizona. These calculations, although relatively simple, are both tedious and time-consuming when computed with a desk calculator and trigonometric tables. In this survey, a large number of pins were surveyed repeatedly, and it was evident that both time and money could be saved by using a digital computer.

Jan 1, 1962

By Francis Foley

IN examining steel under the microscope, one is constantly confronted with structures that are difficult to interpret. Recently, in a collection of samples for exhibition purposes, the writer found apiece of open-hearth runner metal, 2 in. (50 mm.) in diameter, that had been fractured for use as a sample of cast-steel structure. On polishing and etching a section for the purpose of photographing a field to typify the microstructure of steel in the "as cast" condition, a variety of structures was found (Fig. 1) so arranged as to arouse interest at once. For a distance of about 0.065 in. (1.6 mm.) from the skin of the runner, normal ingot structure was found (Fig. 2); this was followed by a zone, about 0.215 in. (5.5 mm.) wide, of considerably lower carbon content in which occurred a most pronounced Widmannstättian structure (Fig. 3); from this point on to the center of the runner, the metal was again of normal ingot structure (Fig. 4). Representative samples taken from the metal in the three zones showed the following analysis: C Ni Cr Metal from skin 0.34 1.26 0.63 Widmannstättian zone 0.21 1.18 0.63 Metal from center 0.34 1.32 0.67

Jan 7, 1919

By Donald A. Bruce

The construction of major structures in karstic limestone terrains poses difficult problems to designer and contractor alike. This reflects the inherent variability of such conditions, and also the significant impacts caused by the construction processes themselves. Three case histories are provided of recent projects in the United States: the sealing of a major inflow into a quarry, the improvement of a highly loaded bridge pier foundation, and the installation of high capacity micropiles. Emphasis is placed on problem assessment and execution verification.

Jan 1, 2002

By Ralph P. Hackl

Ore at the Congress gold property, located near Goldbridge, British Columbia, is extremely refractory with most of the gold disseminated in fine-grained arsenopyrite. Metallurgical testwork conducted by Giant Bay Biotech Inc. indicated that biooxidation pretreatment was capable of increasing cyanide gold recovery from the ore to greater than 90%. To determine if the bioleach process could be successfully scaled up, a 225m' (7950-cu ft) commercial size bioleach reactor was built and tested at the mine site in 1989. At that time, the tank was the largest bioleach reactor ever operated. The objectives of the program were: • to ascertain if the biooxidation rates obtained in lab and pilot-scale reactors could be duplicated in a commercial scale tank; • to identify agitation conditions under which the process will function optimally; and • to demonstrate the bioleach process on a scale sufficient to satisfy the owners and potential investors.

Jan 1, 1990

By Timo Kankaanpää

Keywords: Solvent extraction, dispersion, phase separation, CFD The liquid-liquid dispersion phases are separated by gravity in a solvent extraction settler. This separation step is made more effective by picket fences. The picket fence geometry and its physical placement have a significant effect on the separation process, because the purpose of a fence is to smoothen and control organic-aqueous dispersion flow in the first part of the settler and achieve a deep and dense dispersion layer in the front end of the settler resulting in a clean phase separation. In this study, physical phenomena in the solvent extraction process and phase separation in a solvent extraction settler with and without picket fences have been examined using a commercial CFX software package. It can be concluded that the used CFD-approach proved to be a complementary tool for optimizing and designing the solvent extraction settler.

Jan 1, 2005

By WILLIAM F. McMURRAY, James O. Lewis

The Bureau of Mines is investigating the technology of petroleum and its products, the investigation including well-drilling methods and the transportation, treatment, and utilization of petroleum and of natural gas, with especial reference to the prevention of waste and to increased efficiencyin the development of oil and gas resources in land belonging to or controlled by the Government. During. the winter of 1912-13 the enormous waste of the gas encountered while drilling for oil in the Cushing field, Oklahoma, called forth protests from various sources, and appeal was made to the President of the United States and to the Secretary of the Interior in behalf of the landowner and of the public in general. The facts were wanted regarding the amount of waste and the technical conditions that were responsible for practices causing it. An investigation was ordered and conducted under the direct supervision of the late J. A. Holmes, the first Director of the Bureau of Mines. R. S.Blatchley was sent to investigate the amount of waste going on in the Mid-Continent flelds.s In the latter part of March, 1913, J. A. Pollard and A. G. Heggem were sent to Oklahoma to study well-drilling methods with reference to the waste of gas from wells on Indian lands and to suggest means of preventing the waste of natural gas on such lands. Pollard and Heggem decided that the mud-laden fluid process, which had been used successfully for some years in Texas, Louisiana, and California was the method that would meet the situation most efficiently and economically. The method was accordingly demonstrated in Oklahoma. In 1914 Congress provided for the employment of six oil and gas inspectors to supervise oil and gas mining operations on lands of the Five Civilized Tribes in Oklahoma and to conduct investigations with a view to the prevention of waste. Positions under this appropriation have been held by William F. McMurray, James O. Lewis, Harry D. Aggers, Ralph R. "Weed,George W. McPherson, James C. Fowler, Louis W. Courtney, and Carl H. Beal, the technical work of these men being directed "byW. A. Williams, chief of the petroleum division, Bureau of Mines. After careful and impartial investigation of conditions in Oklahoma, these men also decided that the mud-laden fluid process was the one best adapted to prevent further wastes. In 1915 laws were passed by the State of Oklahoma that provide for the conservation of natural gas and oil, authority being given to the corporation commission to make rules and regulations and to employ agents to enforce them. After hearings and investigations, the corporation commission reached substantially the same conclusions as the Federal agents regarding the importance of the wastes and the best methods of conserving the gas. Technical Papers 66a and 68b were published by the Bureau of Mines in December, 1913, and January, 1914, respectively. Technical Paper 66 deals with the mud-laden fluid process in general and No. 68 with its application in Oklahoma. The interest aroused by these publications has been so widespread that within two years the first editions have been practically exhausted. Rather than reprint these publications, it has been considered advisable to replace them with the present report, which includes the results of more recent investigations. The methods of using the mud-laden fluid are an outgrowth of the rotary drilling system, which was developed in Texas and later employed in Louisiana and California. Some of the principles of the use of mud fluid had been observed and used to a limited extent for a long time in cable-tool drilling. So far as known it was first used successfully with a circulator and cable tools in the Coalinga field, California, in 1906,Harry D. Aggers, one of the contributors to this paper, working on the well. The part of the Bureau of Mines has been to call attention to its merits and to demonstrate its practical use in fields like those of the Mid-Continent.

Jan 1, 1916

By H. M. Smith

MORE than a year before the United States entered World War II, the requirements of the National Defense Program indicated the need for additional sources of aviation gasoline. On September 10, 1940, Dr. R. E. Wilson, Group Executive, Advisory Commission of the Council for National Defense, requested the Bureau of Mines to undertake a survey of crude oils of the United States to designate those suitable for the production of 91-octane aviation gasoline. As quickly as a program could be defined, agreed upon, and funds provided to conduct the work, the Bureau began the project. Over a period of many years the Bureau had collected samples and made analyses of thousands of crude oils produced in the United States. Although these analyses did not include octane numbers of the gasoline fraction, they provided data necessary for calculating the correlation index. This index, developed within the Bureau, is a measure of the types of hydrocarbons present in gasoline and therefore is roughly indicative of the octane value. This fund of information from Bureau of Mines Hempel analyses, supplemented by information obtained from oil companies, reduced considerably the necessary laboratory work by providing data that permitted a large number of crude oils to be eliminated from consideration. However, in the survey carried out during the last part of 1940 and the first half of 1941, 225 samples of crude oil were collected and distilled. Octane values of the distillates were determined by the Army AFD-1C method. (See page 57.) A report containing these results, together with the calculated amounts of 91-octane aviation gasoline available from these sources, was prepared and distributed to the several offices of the Office of the Petroleum Coordinator for National Defense in August 1941. In December 1942 the Office of the Petroleum Coordinator for National Defense became the Petroleum Administration for War (P. A. W.).

Jan 1, 1951

By Floyd G. Anderson

This report reviews and summarizes information on prevention and suppression of dust in mining, tunneling, and quarrying published in the United States from 1961 through 1967. Unpublished pertinent data developed or assembled by the Bureau of Mines during this period also are included.

Jan 1, 1969

By Ulrich Leiste, David M. Fox

This paper presents the results from small scale testing aimed at measuring the loads on a rigid target due to the detonation of a buried mine. The aim of this research is to find how the impulse delivered to the target varies as the air filled void volume fraction within the soil changes.

Jan 1, 2013

By Steve Kral

When the price of gold cracked the US$9.60/g(US$300/oz) mark last year, the gold-mining industry began to crank up again. This followed several years of gold prices that had languished in the mid-200s. Existing mines increased production and mines that had lain dormant for many years were getting second looks. The United States still produces a large amount of gold. But not much of the new production is coming from that country. Instead, strict environmental regulations still have companies wary of trying to invest the millions needed to start a new mine or expand existing ones. And after years of studies and negotiations between legislators, environmental interests and the mining industry, the United States still has not crafted a new mining law.

Jan 1, 2003

By J. Perlacia, J. M. Eguiluz

"INTRODUCTION The Bulk Handling Technology has suffered an important development in the recent years, allowing the use of conveyor belts in the most important and critical applications. As a consequence of this, the reliability and lasting performance of the conveyor belt components is becoming more and more significant, thus the implementation of preventive maintenance programs is a must. The rollers are one of the consumables in the conveyor belts, which have to be changed once arrived to the end of life. The actual ways of detecting this moment always require intensive use of labour and they are not very accurate. Indeed, if the rollers get broken before replacement, the consequences could be very important, generating additional costs and operational losses. The R&D Department of ULMA Conveyor Components, has been working since early 2012 on the development of Monitored Rollers along with a Management Software to provide users the capacity to Manage and Monitor the rollers from its desk, getting continuous online information on the internal temperature of the bearings, on the working status of the rollers as well as the identification of the rollers close to their end of life so that they could be changed during the next maintenance stop of the conveyor belt. In short, a system of Preventive Maintenance for Conveyor Belt Rollers BACKGROUND AND CURRENT STATE The malfunction of a single roller in certain conveyor belts can suppose the standstill of the whole installation until its replacement, due to the risk of greater and more expensive failures like the rip of the belt. In the case of a bulk handling installation where a continuous supply of material is necessary, a bare stop of one hour could entail huge economical losses. What’s more, many conveyor belts are several kilometers length or the access to some parts of them is very complicated. Due to these difficulties the inspection and maintenance operations can become expensive and hard going, with staff going over the whole area checking the correct condition of the conveyor and rollers, which means a dangerous activity. In addition, it’s quite common to find rollers working in very harsh conditions, completely exposed to the elements or working in corrosive closed environments like underground mines. These tough working conditions together with the very demanding features of Bulk Handling sector (high loads, speed, dangerous materials etc.) can bring the unexpected failure of a roller, even being designed to support them. Thus, to have the working conditions of the rollers real time is clearly required, in order to achieve an actual predictive maintenance of the system and avoid fatal failures. Nowadays the most common procedures to identify a broken roller is to hear how it sounds or use thermo-graphic cameras to measure their internal temperature, both of them implying workers inspecting the whole length of the conveyor while the conveyor is running. This means intense use of workmanship and operational safety level reduction."

Jan 1, 2018

By E. A. Anderson

In 1918 the American Society for Testing Materials held a symposium2 on what was then known as season cracking. The sessions included six papers, all on brass. During the ensuing 26 yr., many new workers have come into the field and several other metals have been found subject to failure by stress-corrosion cracking when the right combination of stress and environment is achieved. It is not surprising, therefore, that the present symposium has brought forth 29 papers covering alloys of seven important metals. The phenomenon of stress-corrosion cracking is not necessarily confined to these seven metals. Dix3 has stated, "Indeed, it is probable that ingenious investigators can find solutions which will stress-corrosion crack any known metal or alloy." Mears, Brown, and Dix4 have indicated that stress- corrosion cracking failures are not necessarily limited to metals but may include the plastics. It is to be expected that the increase in the number of metals known to crack in service and the general emphasis on such failures at a symposium such as this will alarm many to whom the subject is un- familiar. Such alarm is not justified by the record. It is true that stress-corrosion

Jan 1, 1945

By Nelson Rivera

El presente texto analiza la crisis económica y su relación con el Banco Minero. Para ello, se revisa las dos últimas recesiones económicas que tuvo el Banco entre 1975 y 1982, donde la crisis se agudizó por una caída en los precios de los metales y una inflación de costos que no pudo ser transmitida al precio de venta. Como consecuencia de ello, las empresas mineras que tuvieron préstamos, acusaron pérdidas en sus ejercicios e incumplieron en el pago de sus obligaciones. Como medida anti-crisis, el Banco Minero estableció comisiones de alto nivel para evaluar las situaciones y recomendar la dación de dispositivos legales que permitieron asistir a los Pequeños y Medianos mineros en la restitución de liquidez mediante préstamos sobre liquidaciones a precios deprimidos, Asimismo, generó la consolidación, refinanciación y moratoria de los clientes que estaban en suspensión de pagos de las obligaciones contraídas con el Banco Minero y la creación de líneas de crédito especiales para la Pequeña Minería.

Mar 1, 1985

By Walter Murphy

For a number of years the Bureau of Mines has been studying the properties of crude petroleums produced in the United States and the Western Hemisphere. A number of reports have been published giving the analyses of crudes from the different field and regions as made by the Bureau of Mines Hempel method of analysis.4/ Several of these reports include analyses off crude oils from the Rocky Mountain region.5/ The search for new fields and new producing horizons in old fields in the Rocky Mountain region has been quite intensive during the last few years, and a number of discoveries have been made.

Jan 1, 1937

JAMES DOUGLAS Dr. James Douglas, twice President of the American Institute of Mining Engineers, and one of its principal benefactors, died in New York on June 25, 1918, at the age of 81 years. After a life of extraordinary activity, failure of his health compelled him to retire about 2 or 3 years ago, and in view of his advanced years his death was not unexpected. His funeral was held at the Church of the Mediator, on June 26, and was attended by representatives of the American Institute of Mining Engineers and of the Canadian Mining Institute. His body was then taken to Quebec for burial in the family plot. An extended notice of Dr. Douglas, prepared by Dr. R. W. Raymond, will be presented in the September issue of the Bulletin. LEWIS NEWTON BAILEY Lewis Newton Bailey died of pneumonia at Camp Merritt, N. J., April 30, 1918, at. the age of 34 years. He was Master Engineer, .Senior Grade, in the Fourth Regiment, U. S. Engineers; and although he was offered a commission as First Lieutenant shortly after enlisting, he preferred not to accept it until he had reached France. By those who knew him well, this lack of eagerness for promotion will be recognized as consistent with his whole character.

Jan 8, 1918

By Gilberto Fernandes Lima, Leonardo Neves, Getúlio Fonseca dos Santos

O refino secundário é um processo onde a homogeneização do aço e as flotações de inclusões ocorrem no banho metálico, cujo conhecimento do tempo de mistura é necessário na produção de aços limpos. A panela, principal vaso onde ocorre o processo, contem plugues ou bicos de injeção de gás inerte, podendo ser utilizados argônio ou nitrogênio, que são responsáveis pela rinsagem do aço. Devido à importância desta etapa neste processo, este trabalho objetivou realizar o estudo do escoamento bifásico do aço na panela com duas configurações diferentes, sendo a configuração um com dois plugues de gás inerte: ambos a meio raio e a configuração dois com dois plugues de gás inerte, um a meio raio e outro no centro da panela. Neste projeto foi utilizada fluidodinâmica computacional, CFD, para a realização das malhas e simulações que forneceram as curvas de traçador e o perfil de velocidade para ambas as configurações. Os resultados simulados indicam que a configuração dois é a mais indicada para o escoamento bifásico, sendo a melhor opção para ser utilizada no modelo de panela industrial.

Oct 1, 2019

By D. M. Doyle

"The Strathcona Concentrator operations, the application of control systems in the crushing, flotation and tailing fill sections, and current and future computer control concepts are described in this paper.The computer has been used for reporting and monitoring roles and operating the on-stream analyzer since start up of the mill in 1968, while over the past twenty months, it has been used for process control. The systems which have been developed include:1. The blending of pentlandite concentrate with pyrrhotite concentrate to produce a special product of constant nickel analysis.2. The blending of cement with tailing fill to produce backfill of consistent cement content.3. The supervisory control of xanthate, frother and pH to the flotation circuits to maintain the nickel copper concentrate grade within narrow limits.IntroductionThe Strathcona Concentrator is currently treating 7,200 tons per day of an ore which contains nickel associated with the minerals pentlandite (28 -32% Ni) and pyrrhotite (0.3 -1.0% Ni). The ratio of the nickel minerals varies from 4 to 15 parts of pyrrhotite to 1 part of pentlandite over the orebody. The production of a high grade concentrate re4uires the separation of this small quantity of .oentlandite from the much greater proportion of pyrrhotite and gangue and is complicated by the presence of two pyrrhotite minerals differing in nickel content, floatability and magnetic susceptibility."

Jan 1, 1974