Search Documents

The reduction of zinc from slags by a molten, carbon-saturated bath was examined in a laboratory study under conditions of continuous slag feeding. The results show that it is possible to reduce the bulk of the zinc from the slag before there is a net reduction of iron. However, the recovery of zinc was not as high as in batch tests performed in an earlier study. Lead in the slag was reduced simultaneously with the zinc to very low levels and was volatilised. Copper in the slag was reduced and dissolved in the alloy. An attempt was made to identify potentially commercial ways of treating zinc slags using an iron bath. The approaches that appear to have the greatest potential are reduction in a batch process using electrical heating and reduction in a continuous process with co- or countercurrent flow of the slag and alloy. In the latter the alloy would be prepared in a separate furnace before being contacted with the slag. The purpose of this would be to superheat and carburise the alloy so that no additional heat or reductant would have to be supplied in the slag-alloy reactor

Jul 1, 1991

By Richard A. Watson

A frequency-shift keying (FSK) modulator-demodulator (modem) network has been devised for the Bureau of Mines mine-monitoring systems. This network permits an unlimited number of remote stations to communicate with one central station over the same pair of wires. The network operates at a speed of 4,800 Bd at distances up to 5 miles. This report describes the development and operation of the modems. The theory of operation, schematic diagrams, and printed circuit board layouts are provided. Although the modems were built for a specific application, a more general use is discussed whereby the network would operate with a typical serial channel format.

Jan 1, 1985

By Radianto Elprama

For the realisation of the underground railway line RandstadRail in the city area of Rotterdam a bored tunnel is under construction. Diaphragm walls up to a depth of about 40 m were used to construct the building pits for the start shaft, the Blijdorp Station and the end shaft. The water tightness of the diaphragm walls was determined by leakage tests that were executed after the construction of the walls, but prior to the excavation of the building pits. The tests showed satisfactory results with a hydraulic resistance of the diaphragm walls of at least 500 days. To determine the water tightness of diaphragm walls it is recommended to follow the specific procedure as described in this paper.

Jan 1, 2006

By George H. Holmes

The water situation in Nevada mineral and related industries is described in this report. It contains information on the sources and adequacy of supply to current operators, requirements and uses, quality and costs, geography, hydrography, precipitation and evaporation characteristics, and Nevada water laws. Also, information is given on the water requirements of one public utility powerplant, and the source and consumption of water in four major cities. Water distribution at 24 operations is shown on schematic waterflow diagrams. The mineral industries of Nevada in 1962 used 8.6 billion gallons of new' water and reused 3.8 billion gallons for a total usage of 12.4 billion gallons. The copper industry was the major water user. The 1962 value of all mineral production in Nevada was $85.5 million. The large amount of water required to maintain thin high production is obtained principally from ground-water sources in alluvial valleys and the permeable rock formations of some mountain ranges. Some water is also obtained from perennial streams and springs. Sources of water utilized by existing industry ire near most mineral industry operations; however, seven companies are forced to pipe water distances ranging from 2 to 8 miles. Although water supplies of presently operating companies are adequate at most operations, several companies resort to large-scale reuse of water as a matter of conservation and economics. Acquisition of water by new operators is possible but takes considerable negotiation. Water rights, surface and underground, are controlled by the State. The quality of the water is satisfactory for most purposes. Analyses of 19 samples, listed in the appendix, show the range in water quality at various plants throughout the State. Costs of delivering new water to current operations range from 2 to 26 cents per 1,000 gallons with an average of 10 cents per 1,000 gallons for power and maintenance. No firm costs for recirculating water were available; estimated costs range from 1.5 to 2.5 cents per 1,000 gallons. The mineral-product value of the entire Nevada mineral industry in 1962 was equivalent to $10 per 1,000 gallons of new water and $26 per 1,000 gallons consumed. Projection of the 1962 water requirements of the Nevada mineral industry indicates that the demand For new water will increase from 8.6 billion gallons in 1962 to 11.9 billion gallons in 1980, a 43-percent increase. Water requirements in the year 2000 are estimated as 14.8 billion gallons, an increase over 1962 water demand of 78-percent.

Jan 1, 1966

Extraction of copper from a chalcopyrite concentrate by means of a cupric chloride leach is described. Initially the concentrate is mixed with sulphur in a 9: 1 ratio, and heated to 350-400°C. This converts the chalcopyrite into more readily soluble sulphides, while the iron rejected from the chalcopyrite is transformed to pyrite, which is insoluble in the leach solution employed. A two-stage countercurrent leach using a leach solution of 1 M cupric chloride, 3.5 M sodium chloride, and 1 M hydrochloric acid extracts 98 per cent of the copper, if conducted at 105°C. Iron extraction is relatively low, the mole ratio of iron to copper extracted being 0.17, compared to 1.0 for unreacted chalcopyrite. After dissolution, copper can be recovered by electrolysis, cupric chloride leach solution being regenerated at the anode.Electrolytic power requirement is low, being approximately 0.5 kWh per kg of copper. The sulphur and, most of the iron entering as feed are rejected from the process in the form of pyrite, which remains in the leach residue.

Jan 1, 1974

By J. Mitchell Linnet

Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources and potential of deposits in the Bucks Lake and Chips Creek RARE II areas in Plumas and Butte Counties, California. These areas lie along the west slope of the Sierra Nevada on opposite sides of the North Fork Feather River and encompass an area of 62,800 acres (25,400 ha). Metasedimentary and metavolcanic rocks of the Pennsylvanian Calaveras Formation are intruded by plutons of Mesozoic age. Mineral; of economic iterest are in quartz veins in metasediments close to these plutons; they are principally gold and silver with minor amounts of copper, lead, and zinc minerals. Molybdenum, copper, silver, and tungsten minerals occur in tactite along metasedimentary-granitic rock contacts. In both areas, auriferous Tertiary channel gravels have been extensively developed. Asbestos occurs in ultramafic rocks in both areas, and a limestone deposit was explored in the Chips Creek area. Gold is the principal economic mineral in the Bucks Lake RARE II area. The Shenandoah Mine (fig. 1, no. 19) contains 7,500 tons (6,800 t) of indicated and inferred subeconomic gold resources in sulfide-bearing, silicified metamorphic rocks of the Calaveras Formation (table 1). Similar rocks have yielded gold at the Edman and Megowen Mines, adjacent to the area. A high potential exists for additional lode resources in the area around the Shenandoah Mine. Callahan Mining Corporation personnel believe a multi-million ton disseminated gold deposit underlies the property.

Jan 1, 1983

By Bali. D. D., S. Chattopadhyay

"The planning and construction of prime coking coal beneficiation plants in the nationalized mines in India are reviewed. Flow schemes, construction practice, materials consumption, and costs are detailed.Medium-capacity beneficiation plants with multiple loops are recommended under Indian conditions.IntroductionThe reserve of high-grade and easily washed metallurgical coal in India are quite limited. Prime coking coal constitutes approximately 22% of the total resources and occurs exclusively in the Jharia coalfield in the state of Bihar. Bharat Coking Coal Limited (a subsidiary of Coal India Limited (CIL) the nationalized mining sector of India) owns 80% of the Jharia collieries. The development of Jharia coalfield in the pre-nationalized period before 1971 has been characterized by a large number of small mines with primitive mining methods and low productivity. The production of prime coking coal to meet the demand of the steel industry in India has to increase from the existing level of 11.1 million tonnes to 43.4 million tonnes per annum by 2000 AD, thereby producing 5.61 million tonnes and 22.7 million tonnes of clean coal respectively. An ambitious program has been undertaken for development of bigger mines with an average production of 1 to 3 million tonnes per annum. With the fast dwindling reserves of good quality coking coal, more inferior grade coal seams, having difficult washing characteristics, are now being mined. All the coal from the future mines will have to be beneficiated to make it suitable for consumption of steel plants; the following washeries are being planned for construction by 2000 AD:"

Jan 1, 1986

By M. Nete

Qualitative analysis of three mineral samples from northern Mozambique was accomplished by X-ray diffraction (XRD), microscopy, scintillation, and magnetic determination. Chemical characterization was accomplished using ICP-OES and pressed powder XRF after dissolution using microwave-assisted digestion and flux fusion. The samples consisted of a mixture of minerals with tantalite as the major component, with minor amounts of microlite, quartz, mica, accessory garnet, and tourmaline. Incomplete dissolution was obtained using microwave digestion, with maximum recoveries of 90.25 ± 0.06% and 88.90 ± 0.04% for Nb2O5 and Ta2O5 respectively. Complete dissolution using Li2B4O7 resulted in recoveries of 98.5 ±0.2% Nb2O5 and 100.4 ± 0.3% Ta2O5.

Jan 1, 2012

By U König, N Norberg

To cope with varying raw material qualities and increasing prices for energy, a more frequent and accurate monitoring of the processing of iron ore became the focus in sinter plant operations. Traditionally, quality control in iron producing industries has relied on time-consuming wet chemistry or the analysis of the elemental composition. The mineralogy of a sinter that defines the properties and behaviour in the blast furnace is often not frequently monitored. One fast method to analyse the mineralogical composition of iron sinter, raw mixtures and iron ores is X-ray diffraction (XRD). Recently statistical methods such as similarity analysis or partial least square regression (PLSR) in combination with XRD raw data has become more and more popular in handling large amounts of data and correlating process-relevant parameters directly with an XRD measurement. PLSR can be used to correlate process parameters directly from the XRD pattern without investigating the mineral content. Hidden information that is present in the measurement but not determined with traditional methods can be used to improve the characterisation of the analysed materials.CITATION:König, U and Norberg, N, 2017. Iron sinter process control using X-ray diffraction – part : monitoring of low temperature degradation, in Proceedings Iron Ore 2017, pp 75–78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Biosorption of Cr(VI), Pb(II) and Zn(II) from Aqueous Solutions by Immobilised Phanerochaete chrysosporium Biomass in a Fixed-Bed Column The continuous-flow adsorption of Cr(VI), Pb(II) and Zn(II) from aqueous solution by immobilised Phanerochaete chrysosporium biomass in a fixed-bed column was studied. The effects of flow rate, influent concentration of Cr(VI), Pb(II) and Zn(II) and bed depth on breakthrough curves and biosorption capacity were investigated. The experimental results showed that the breakthrough time decreased with increasing flow rate, increasing influent concentration and decreasing bed depth. The data also indicated that the equilibrium uptake of Cr(VI), Pb(II) and Zn(II) increased with decreasing flow rate and increasing influent concentration of Cr(VI), Pb(II) and Zn(II). Two models were employed to predict the breakthrough curves and to determine the characteristic parameters of the column useful for column design. The Thomas model was able to predict the breakthrough curve in the range of relative concentration(Co/Ci) higher than0.3, Cr(VI), Pb(II) and Zn(II) whereas the validity of the Bohart-Admas model was limited to the initial part of breakthrough curve at all flow rates and influent concentrations of Cr(VI), Pb(II) and Zn(II). The feasibility of reusing the immobilised fungal beads through five adsorption/desorption cycles in fixed-bed column was investigated.

Sep 13, 2010

By Will B. Jamison

An ignition detection and suppression system was developed under the scope of this contract. The objective of this machine mounted system was to detect flames caused by frictional sparking from the cutting bits of a continuous mining machine and to suppress it with sufficient speed to prevent the development of an explosion, and to keep the flame from harming the machine operator.

Jan 1, 1976

By Robert B. Johnson

The refraction seismic method has been used as an indirect means of exploring for fluorspar in southern Illinois by the Illinois State Geological Survey. Use of the method has been restricted to those areas where mineralization is associated with faults, a restriction necessitated by the operating principles of the refraction method. The seismic data enable the interpreter to locate fault zones in the subsurface and, under ideal circumstances, to make estimates of dip direction and magnitude and vertical displacement provided the local stratigraphic units are known and are geophysically recognizable. In this instance, refraction seismic exploration has been successful in the surface mapping of well-developed faults, both simple and complex with which fluorspar may or may not be associated. However, less clear results have been obtained where faulting has been less severe and where there are numerous accompanying mineralized joints.

Jan 1, 1964

1. Book reviews Mill Operators' Conference. Parkville (Australia), Australasian Institute of Mining and Metallurgy, 1982. 425 pp. Reviewer: B. K. Loveday Off highway truck haulage. Newman Combined Group, the Australian Institute of Mining and Metallurgy and the Institute of Engineers in Australia. Sep. 1982. Reviewer: B. J. Vorster Environmental engineering in South African mines.Johannesburg, Mine Ventilation Society of South Africa, 1982. 974 pp. Reviewer: A. N. Brown Underground Operators Conference. West Coast Tasmania Branch. Australasian Institute of Mining and Metallurgy. Reviewer: D. R. Aspeling 2. New publications Electric steelimaking in the eighties: challenges and opportunities. Rotterdam, Balkema, 1982. 362 pp. $50.00 or £33. Tungsten: a review, by P. M. Harris and D. S. C. Humphreys. London, Institution of Mining and Metallurgy (Occasional Paper 2), 1983. Members: £3, nonmembers £6. The platinum industry - prospects in recovery. London, Shearson{American Express Ltd (St. Alphage House, Fore Street, London EC2Y 5DA), 1983. £75. The best of E&MJ mining and processing idea book' New York, Engineering and Mining Journal, 1983. 128 pp. Free with subscription to Engineering and Mining Journal. Mining 1983. Harlow (U.K.), Longman Group Limited, 1983. 500 pp. £39.50. Ooncise guide to world coalfields. London, World Coal Resources and Reserves Data Bank Service (14/15 Lower Grosvenor Place, London SW1W OEX), 1983. 380 pp. £45. 3. Canadian publications Asbestos, by G. O. Vagt, 9 pp. Ooal and Coke, by J. A. Aylsworth, 16 pp. Orude oil and natural gas, by R. L. Thomas, 12 pp. Phosphate, by G. S. Barry, 8 pp. Rhenium, by S. A. Hamilton, 3 pp. 4. Mintek reports Report 2102D The recovery of magnesite from dump fines from the Strathmore Mine. (First issued Feb. 1981.) Report 2106D The evaluation of drill cores and a bulk sample from a deposit of andalusite near Thabazimbi. (First issued Mar., 1981.) Report 2108D Evaluation of a grinding aid in batch grinding, classification, and gravity concentration. (First issued Jul. 1981.) Report 2109D The evaluation of an andalusite deposit from Kleinfontein, Groot Marico. (First issued Apr. 1981.) Report M7D The beneficiation of chromite ore from the Ma-l seam near Marikana. (First issued Nov. 1981.) Report M62 A preliminary investigation into the extraction of zinc by direct oxidative leaching of high-manganese sphalerite. Report M76 A mineralogical investigation of a refractory gold ore, and of a sulphide concentrate and calcined tailing from that ore. Report M85 List of unrestricted Mintek publications issued from 1966 to 1982. Report M97 Reduction in metal consumption by the use of alternating lines of higher and lower lifter bars in a rod mill. Report M98 Multivariable control and optimization of the operation of a milling circuit at East Driefontein Gold Mine. Report M101 The potentiality of heat-treated balls in the grinding of gold ores. X-ray diffraction The Southern Transvaal Section of the South Mrican Chemical Institute is to present a mini-course on 'X-ray Diffraction: Theory and Application' in Johannesburg on 18th and 19th October, 1983.

Jan 1, 1983

By S. S. Todd

[The purpose of this investigation was to obtain, heat-of-formation values a four Common titanates and, to conjunction with other requisite data, to derive free-energy-of-formation values In tem peratures in the range of 1,600°-1,800° K. T ht four titanites are tricalcium ?ditanite !['a¬spheremr?raritanar( rint-tir.rniurn rill( 1 This rc rr,rt sul,rlc?nu?nIs :r },r; vinu~ hul,lrc.irse,n3i n wlti h eht-rmnnIN-ti i n c {ar.a ai?rc? pu -,csseeri (or, 11 in(c-rnxiLIic co mrc+unrls conraininL~ rir:,niurrl. 'f Lac? !1~:)mc? c?xpcrirnc'ntnl n-ut rhod w,i. rna~loycul. lic?.ats of for rn:ltion of rlre comi?c,unr4~ it 29S.N. ut re mca,urc?,l by tioItl[ion e':iIorrr)utrv, using a ctrneaR }ryrlrc,fllanric-hY rir~chlorie- ,aci l mixttrrt .is rhr c-zle~rinrrrric- fluid and rc.actic~n rtu,liura}.]

Jan 1, 1956

By L. B. Pankratz

Thermodynamic data on the halides were reviewed, evaluated, and compiled at the Bureau of Mines Albany Research Center. Values for Cp°, S°, H-H°298, -(G°-H°298)/T, ?Hf°, ?Gf°, and log Kf are given in tabular form. CP°, H-H°298, ?Hf°, and AGf° are also expressed algebraically.

Jan 1, 1984

By S. H. Ash

THIS REPORT covers the second in a series of five projects into which the Conowingo tunnel system has been divided for geographical and practical reasons. It outlines the construction work contemplated-to sink two shafts on the line of the main tunnel that are designated the Nos. 9A and 11 shafts, to turn off from the No. 9A shaft the Lansford and Lykens laterals, and to drive portions of the main tunnel. An emergency pumping plant, consisting of 2 separate pumprooms, each containing 3 horizontal-type centrifugal pumps of 100,000-gallons-per-minute (g. p. m.) capacity, will be constructed at the No. 9A shaft. From the No. 11 shaft will be turned off the Trevorton lateral and portions of the main tunnel, which will connect with the section driven from the No. 9A shaft. Under the proposed project, the Lansford lateral will be driven for a distance of 2 miles, the Lykens lateral for a distance of 10.56 miles, and the Trevorton lateral for a distance of 20 miles. To drive the Lykens and Trevorton laterals for the distance indicated, several construction shafts and slopes must be sunk to permit efficient and safe construction.

Jan 1, 1955

By Márcio Zamboti Fortes

A alguns anos os setores residencial e industrial tem se deparado com mudanças de paradigmas que tangem a necessidade de melhorias em suas atividades, com o intuito de desenvolver processos com menor impacto ambiental, sustentáveis e com eficiência energética, objetivando reduzir o consumo de energia elétrica. O uso de tecnologias baseadas em fontes renováveis para a geração de energia elétrica, tais como a solar e a eólica, tem apresentado-se como uma alternativa a ser implementada por estes setores para atender às exigências do mercado, se beneficiando da difusão da tecnologia e uso destes equipamentos, para a consciente utilização da energia elétrica. A instalação e avaliação de novas fontes de geração de eletricidade estão sendo desenvolvidas pelo projeto Cidade Inteligente de Búzios através da implantação de painéis fotovoltaicos e aerogeradores de pequeno porte em unidades consumidoras residenciais, comerciais e industriais e alguns resultados estão apresentados neste texto.

Sep 25, 2017

By Karl J. C. Harries

"1.1. WHAT ARE AGREEMENTS AND HOW ARE THEY FORMED?In order to have an agreement, at common law, there must be an offer, acceptance of that offer, and consideration passing between the parties. In addition, the material terms (i.e. the basics or substance) of the agreement must be discernible, preferably by means of documentation. Although these concepts may appear simple and straightforward, the law relating to them is voluminous and complex. Some brief comments are worthwhile.• Offer/acceptance: Both offer and acceptance should be in writing, but they need not be. The actions, conversations, and/or correspondence of the parties may constitute either or both of them. Notwithstanding, the local law or practice of a jurisdiction will impose some specific requirements for certain types of agreements. If these requirements are not met, the agreement may be unenforceable. For example, Ontario’s Mining Act requires transfers of unpatented mining claims to be evidenced in writing and recorded.1• Consideration: Consideration is usually thought of as being money, but it can be virtually anything, even “the premises” (i.e. the mutual covenants or promises contained in the agreement itself). In addition, if one party, relying upon the offer of another, does something to his detriment, then the doing of the act can be considered to be an acceptance of the offer and, under the legal concept of “detrimental reliance”, can also be consideration. Whether or not detrimental reliance exists will depend upon the circumstances of each case.2• Material terms: The requirement that the material terms of an agreement must be discernible does not mean that all of the terms of an agreement must be documented or even have been considered, just the basic or material ones. In addition, it will be up to a judge to decide what is material – not necessarily the parties. In order to establish the material terms, a Court may look at all relevant documentation and may hear oral evidence. It will resist “writing the agreement”"

Jan 1, 2003

By Du Sichen

The present paper presents the modeling of gas-solid reactions in the case of the decomposition of CaCO3, describing the reaction kinetics on the basis of heat-transfer concepts which could be compared with thermogravimetric results. In the case of solid-solid reactions, the present paper describes the model developed for describing solid-solid reactions from dynamic X-ray diffraction technique, developed by the present team. The model has been successful in explaining the formation of spinel from MgO and Al2O3.

Jan 1, 2006

By H. P. Greenwald

[In many coal-mining countries, during he pest decade, there have seen made extended studies and accurate measurement of movement of roof strata, tests of the physical properties of specimens cut therefrom, and tests of the strength of end load on artificial supports. Naturally, such studies have been more extensive in European countries, where mining conditions are less favorable than in the United States. As a part of its work in the conservation of coal resource and prevention of accidants in mines, the Bureau of brines began systematic measurements of the movement of roof strata to in coal mines in the fall of 1935. It was decided- that, in the beginning, work on a rapidly retreating rib line in a mechanized mine would give the greatest amount of information in a reasonable time. To this end w cooperative tine agreement was made with the Pittsburgh Coal Co., through Dr. L. E. Young, vice: president in charge of operations, for conduct of work in that company's Montour 10 mine operating in the Pittsburgh coal bed. This paper gives an account of the methods used in the investigation, excerpts from the data obtained, and such generalizations as appear to be justified.]

Jan 1, 1937