Search Documents

By Christopher J. Bise

INTRODUCTION The level of analysis for the selection of extraction practices and equipment for surface mining differs significantly from that found in underground mining. In underground mines, manufacturers establish the operating ranges of the equipment, such as continuous miners, loaders, and boring machines, based upon required clearances. Even in conventional mining, the drilling and blasting operation is usually based upon experience. The selection of extraction methods and equipment for surface mining is more complex. Since the equipment is not as confined as in deep mining, and the topography tends to be highly variable over the limits of the mining property, primary extraction equipment must be sized according to reach and capacity. Further, due to the depositional characteristics of the over- burden, drilling and blasting patterns must be well- designed to provide proper fragmentation. The following sections provide a general outline for the selection of surface excavation practices and equipment. The topics covered include drilling and blasting and the selection of both primary extraction equipment (draglines and stripping shovels) and secondary extraction equipment (bulldozers, scrapers, and front-end loaders). EXCAVATION FUNDAMENTALS Before discussing surface excavation, a few concepts need to be defined. A bank cubic yard of material is equal to one cubic yard as it lies in its natural or undisturbed state. A loose cubic yard is that portion of a bank yard that after being disturbed has expanded to measure one cubic yard. Swell is the volume increase of a material when it is removed from the natural state. Finally, load factor is the percentage decrease in the density of a material from its natural state to a loose state. Table 1 summarizes these concepts for various materials. When the amount of overburden to be removed to meet a predetermined production rate is established, a suitable bucket size for the primary stripping equipment must be calculated. The following equation can be used: NBSIZE = TBC/[(OF) (BF)] (1) where NBSIZE is the actual bucket capacity after considering the swell percentage, the bucket fill factor, and the operating efficiency; TBC is the theoretical bucket capacity (TBC = COB/NTCPM); OF is the operating efficiency; BF is the bucket fill factor; COB is the cubic yards of overburden to be removed; NTCPM is the number of theoretical cycles per month [NTCPM = (SMH) (3600)/(CT)]; SMH is the scheduled monthly hours; and CT is the cycle time in seconds. FRAGMENTATION PROCEDURES Drilling Where the strength of overburden material is such that blasting is required prior to excavation, drilling is conducted before using explosives. Two methods of drilling are found in mining-percussion and rotary. Penetration of overburden by percussion drilling is carried out by successive impacts of the bit into the rock. Emphasis in this section will be placed on rotary drilling, because for surface mining it is the most versatile form of overburden penetration. Rotary drilling is conducted by rotating a rigid string of tubular rods to which a rock-cutting bit is attached. The drilling energy is supplied by rotation as well as thrust and the cutting action consists of abrasion, scraping, spalling, or chipping. The size range for rotary-drilled blastholes is from 4 in. to 15 in., with 9 in. and 12 in. being common sizes. There are two types of bits used for rotary drilling-drag and rolling cutter. Drag bits are applicable in soft to medium-soft shales or their equivalents. Since their effectiveness is dependent upon a successful scraping action, drilling thrust is lower for drag bits than for rolling cutter bits; the opposite is true for torque requirements. The bits are usually fitted with replace- able tungsten-carbide cutters. Rolling cutter bits, though available in a two-cone configuration, are usually of the three-cone style (Table 2). The rolling cones have either large steel teeth for drilling through soft formations or small tungsten-car- bide inserts for drilling through hard formations. Table 3 relates bit size and weight to the strength of the rock. The major advantage of rotary drilling is its rapid drilling rate. This is due to the fact that, unlike percussion drilling, rock penetration is uniform with depth. Blasting Effective bank preparation deals not only with the fragmentation of overburden but also with the mini-

Jan 1, 1986

By Dennis Molvik, Omar Fulton, Chris D. Breeds, Don Gonzales

This paper presents and describes the South Interceptor Parallel Phase III Contract C93012C, which involved construction of a nominal 2.7 m (9-ft) finished diameter sewer conveyance using both pipe jacking and conventional tunneling methods. Earth Pressure Balance (EPB) excavation was required to minimize the potential for settlement beneath a main rail line, overpass, sensitive wetland, areas of contaminated soils, and nearby structures. Ground conditions predicted in the Geotechnical Baseline Report included low plasticity, clayey silt (40 to 10%) and silty sand (60–90%) with pieces of wood such as logs, stumps, branches and other tree fragments. Soil cover ranged from 2.7 m (9-ft) to 5.4 m (18-ft) over the tunnel crown with a groundwater table between 1.5 m (5-ft) and 3.7 m (12-ft) deep.

Jan 1, 2003

By D Reddy Chinnasane

Outline Location of BirchtreeMine and Layout of 124 OB Cut and Fill Mining Background Purpose of the Studies Methodology Results and Analysis Conclusions and Recommendations

Oct 1, 2010

By John C. Holtz

Interest in the possibility of using Diesel6/ engines for haulage power in mining and tunneling is increasing in the United States, owning largely to the reported successful use of Diesel locomotives in European coal mines and to the comparatively recent development of automotive Diesel engines in this country. The extent of this interest has been evidenced to the Bureau of Mines by numerous requests for information as to the factors that must be considered if Diesel engines are to be used safely underground.

Jan 1, 1940

By Francisco Geraldo Toledo Junior

Os aços inoxidáveis possuem características essenciais para um bom acabamento quando o que se busca é estética e boa resistência à oxidação. Quando se específica um aço inoxidável, o acabamento é um dos aspectos relevantes que devem ser considerados. O acabamento possui uma importante influência em algumas características do material como, por exemplo, na facilidade da limpeza e na resistência à oxidação / corrosão. Há uma grande variedade de acabamentos. Através de ensaios de oxidação a quente, medição de potencial eletroquímico, medição de dureza a baixa carga (microdureza) e medição da tensão residual via difração de raios x foi possível perceber uma diferença entre os acabamentos 2D, 2B, RO, BB, Nº4 e Nº6. A medição de tensão residual mostrou qualitativamente que o aumento de dureza e o forte amarelamento ocorrido no material com determinados acabamentos é função de uma deformação elástica na superfície imposta durante alguns dos processos de fabricação desses aços. Esse mecanismo é relevante e interfere na resistência a oxidação e corrosão nos casos estudados.

Aug 17, 2017

By John C. Holtz

Interest in the possibility of using Diesel6/ engines for haulage power in mining and tunneling is increasing in the United States, owing largely to the reported successful use of Diesel locomotives in European coal mines and to the comparatively recent development of automotive Diesel engines in this country. The extent of this interest has been evidenced to the Bureau of Mines by numerous requsts for information as to the factors that must be considered if Diesel engines are to be used safely underground.

Jan 1, 1940

By Michael S. Kucker, Stuart Warren, Robert A. Robinson, Michael J. Lehnen, David McAllister

Geotechnical conditions exposed by the phased exploration programs have had a major impact on the selection of excavation and support methods, dewatering requirements, size of openings, vertical alignment, and estimated cost of construction for the Beacon Hill Tunnel and Station section of the “Link” Light Rail. Beacon Hill is comprised of a very complex glacial geology, including numerous slickensided fractures, injected sand dikes, and multiple perched groundwater levels as revealed by a phased boring program and exposed in a test shaft. The Geotechnical Baseline Report (GBR) presents this complex geology along with a “tool box” of alternative additional support systems to accommodate the varying ground conditions during construction of the station excavation. Additional explorations will also be accomplished during construction to further refine the geotechnical interpretations and provide an opportunity to use pro-active ground improvement techniques to optimize the station excavation and support requirements.

Jan 1, 2005

Coals from the Southern Coalfield of New South Wales treated in the Port Kembla coal preparation plants of Australian Iron and Steel Pty. Ltd. differ supstantially in their characteristics. Knpwledge of performance not only enables comparison and promotes better control, but also provides the means for predicting results.Evaluation of performance of cleaning equipment has been made in terms of probable error (Ep). Results for Baum jigs, a Chance cone, heavy medium cyclones, and water washing cyclones were examined. The efficiency factors derived from the probable error were applied to the float and sink analysis, mathematically simulating operating conditions. This method was applied to the Balgownie seam.The Balgownie seam lies between the Bulli and Wongawilli seams in the coal measures of the South Coast and mining on a large scale began recently in the Bulli area. It is known locally as the Four Foot seam and exhibits rather difficult washability characteristics, due to a comparatively high middlings content. These properties and the relatively high inherent ash make careful selection of cleaning equipment essential for optimum recovery. The prediction technique is used to determine the possible results when this coal is cleaned in the Port Kembla plants. Predicted values are compared with results from full scale trial washings demonstrating the validity and accuracy of the technique.Applications of result forecasting are listed.

Jan 1, 1971

By Michael J. Beus

This Bureau of Mines report describes a tunnel stress relaxation gage (TSR) developed to measure initial radial displacement around full-sized underground openings. The TSR technique was shown to be a valid concept in previous field verification tests. Sensitivity has been improved by employing a titanium alloy cantilever in the transducer head, which also permits a deeper sensor location. Use of improved fabrication methods such as stainless steel bellows and sputtering techniques and use of an environmental chamber for testing greatly increased overall reliability. A miniature data acquisition system (DAS) was interfaced directly to the transducer for increased versatility and containment entirely within a borehole. The present TSR system is suitable for use around full-size underground excavations, particularly machine-bored openings. Field evaluation of the improved instrumentation verified the design goals.

Jan 1, 1978

By M. Gallego, R. Oyarzun, L. Ortega

Evidence of metallogenic activity in an area dominated by Upper Precambrian and Palaeozoic metasediments was partially explained in the 1980s when drilling and a geophysical survey detected hidden intrusions, but questions remained to be answered about the nature of the fluids. Sb mineralisation at El Juncalon vein-type deposit was selected for geological, geochemical and fluid inclusion studies as a model with a relatively simple quartz-stibnite-pyrite paragenesis. Many of the characteristics were those of Chinese-type vein Sb deposits, which can be regarded as atypical of the epithermal type as they are hosted by clastic rocks

Aug 1, 1995

By Walter Voglauer, Elisabeth Zechmeister

Five serial photos show the first second of the demolition of a 75 m high, reinforced concrete tower in the 23rd District of Vienna, Austria. The tower demolition with high explosives was necessary because a 175t excavator could not finalize the destruction with mechanical tools. All mechanical works in preparation of the blast, such as the borehole drilling, were done by civil companies under the responsibility of the contracted demolition company PRAJO. The blasting itself was planned and executed by the engineer corps of the Austrian Armed Forces, Sunday, May 26, 2013. Nearly 800 boreholes filled with more than 100 kg of military plastic explosives were initiated with about 1,600 Austin electric delay detonators in exactly 1,000 ms and 30 steps of delay. The 10,000 tons of reinforced concrete tower fell as planned without any damage to the environment. Photo 5. The rest of the detonators initiate the water pools filled with high explosives forming a bizarre white water front to fight the following strong development of dust. The first 1,000 milliseconds are over.

Jan 1, 2015

By H Zhou, T Honeyands, M Zhou

In iron ore sintering, packing the granules onto the sintering strand to form a porous bed with optimum permeability is a complex dynamic process. The packed bed voidage is the key factor determining the flame front speed and the final sinter productivity and quality. Previous studies have found that granules are soft quasi-particles with a typical structure of nuclei with an adhering fines layer. The deformation of the adhering layer greatly affects the bed voidage during packing, which is related to the strength of the adhering layer and the force exerted on the granules. In this study, tablets simulating the particle size distribution in the adhering layer of granules were made for four single ore blends. Both the tensile strength and shear strength properties of these tablets were investigated as a function of water content by the uniaxial compression test and direct shear test respectively. The results of compression tests show that the adhering layer becomes weaker and more compliant with the increase of moisture. The most porous ore has a more rigid adhering layer than the other three tested iron ores at any given moisture content. In direct shear tests, the internal friction angle of the adhering layer ranged from 31° to 37° and varied little with the moisture content or ore type. The cohesion constant is around 1 kPa and is quite small compared to the stress applied to the granules during packing. Combined with the results of granulation and packing experiments, the influence of the adhering fines layer deformation on the degree of voidage loss is specifically discussed.CITATION:Zhou, M, Zhou, H and Honeyands, T, 2017. Tensile strength and shear strength properties of the adhering layer of granules in iron ore sintering, in Proceedings Iron Ore 2017, pp 117–112 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By James L. Ash

This report contains the results of a technical and economic evaluation of conceptual systems for the underground mining, rubblization, and in situ retorting of deep oil shale deposits. Study efforts were first directed towards evaluation of the applicable geology, associated minerals, rock mechanics, in situ retorting, access mining, ventilation, rubblization, safety, and environmental impact factors. Conceptual systems were synthesized and then evaluated against these factors from both a technical and limited economic viewpoint. The results of these evaluations were then analyzed and, based upon this analysis, the following two systems were selected for further study: System II: Room and Pillar-Vertical Drill and Blast System IV: Tunnel Boring-Horizontal Ring Drill and Blast Due to the large number of variables to be considered, a computer program was developed and utilized to provide data for the cost trade-off studies and economic analysis. Results of the early computer runs indicated the value of the tool available? in the computer program and led to an extension in the contract to determine the sensitivity of the systems to several of the more apparent significant variables. These results in turn led to a refinement in the design assumptions and a better understanding of the technical and economic options available to an owner-operator of a Vertical Modified In Situ Shale Oil Extraction System. This report is submitted in fulfillment of the requirements of Contract Number 50241073 by Fenix & Scisson, Inc. to the Denver Mining Research Center, United States Department of the Interior, Bureau of Mines. Work was completed as of November, 1976.

Jan 1, 1976

By C. Schuffeneger

"The design of SAG milling circuits for mining projects requires the incorporation of the energy consumption considerations and the evaluation between different flexibility-adding options to absorb the time-dependent variation in the ore lithology. In order to expand the focus of the engineering design, a higher level of deepness and quality in the baseline information must be achieved to elucidate all of the constraints on throughput, energy consumption and product quality generating a design optimization consistent with an integrated vision of the process. This paper presents a review of a collection of typical examples of the copper and gold mining project in the Chilean Andes, in which both process and energy efficiency criteria are considered when the focus is to deliver an integral solution that incorporate those areas in the design. The intensive use of energy in the SAG milling, the process continuity and the quality of the product are a function of the proper design and selection of grinding equipment and plant layout, aligned with the mining plan and associated with projected future expansions and production increases.INTRODUCTION Autogenous and Semiautogenous grinding technology, large diameter and short length mills, begins with the Handsel design. During the decade of 1930’s, Handsel-Hardinge studies led to cascade mill development. Nowadays, 80 years later, continuous improvements in design and technology have been conducted to a completely new generation of gearless SAG mills that have led to an increasing capacity at the concentrator plants. Considering the existing alternatives, SAG mills are the most implemented option for the grinding circuit today. This work presents a review of the SAG mill implementation parameters and circuit considerations and its correlations in the most recent projects in Chile with an ore treatment capacity above 50 ktpd since the decade of the 90’s up to now. From this period, the tendencies will be analyzed using project design data. Based on process design information, the recent SAG mill history in relevant projects related to the new generation of commercial SAG mills, technical associated considerations and performance will be discussed. Circuit selection based on energy utilization will be revised to bring up a more holistic perspective on the SAG mill circuit design concepts. As is now well known, the heart of every concentrator plant are the grinding mills. Higher demands on throughput, availability and power consumption optimizations require not only high performance electrical equipment but also a well selected grinding circuit. The energy efficiency issues associated to the circuits design will be reviewed."

Jan 1, 2012

When the 2008 Olympic Games begin in Beijing, China is September it will not only mark the end of the journey for the Olympic torch and the thou-sands of participating athletes, but the games will also mark the culmination of a massive amount of construction in the city. On display for the world to see will be 31 new and refurbished venues including the 91,000-seat National Stadium called the ?Bird?s Nest? and the aquatics center, called the Water Cube. What will not be featured as prominently on the television cameras broadcasting the games around the world will be the network of tunnels built beneath the city. But that infrastructure of rail lines will be of critical importance to the games. While preparing to host the world, China added a subway tunnel that will include four stops in the Olympic Park. The 4.4-km (2.7-mile) subway line that runs through the complex of stadiums, gymnasiums and parks began trial operations in June. Prior to the opening of that line, Beijing's No. 5 subway line, which runs through the heart of the city from north to south, opened in October. That 27.6-km (17-mile) line took nearly five years to build and includes 23

Jan 1, 2008

By G Eastwood, C Joyce, P Ryan, G M. Johnston

Over the years, predictive techniques for Acid Mine Drainage (AMD) and the natural processes affecting acid generation have received considerable attention. Less emphasis has been placed on the sampling strategy and the integration of testwork results with the geological data base. The sampling strategy employed and the development of a geological model to determine the spatial distribution and volume of acid producing material are often crucial for developing cost-effective containment and mitigation measures. The geological model provides a link between the occurrence, timing, destination and placement of mined waste rock. Careful and accurate interrogation of a comprehensive geological database provides this linkage. The AMD testwork program at Cadia in NSW has been designed to identify the temporal selective handling requirements that will be required during operation. Sampling involved collection of representative combinations of all waste rock types identified within an extensive geological database. These samples were subjected to static, kinetic and accelerated weathering predictive tests. Preliminary results have been used to construct a waste block model for the deposit that identifies the quantity and distribution of acid producing material. Integration of the block model with the mine scheduling determines when the material will be mined.

Jan 1, 1996

By CIM Standing Committee

The CIM Definition Standards on Mineral Resources and Reserves (CIM Definition Standards) establish definitions and guidance on the definitions for Mineral Resources, Mineral Reserves, and mining studies used in Canada. The Mineral Resource, Mineral Reserve, and mining study definitions are incorporated, by reference, into National Instrument 43-101 – Standards of Disclosure for Mineral Projects (NI 43-101). The CIM Definition Standards can be viewed at mrmr.cim.org. Readers should be aware that reports written by persons issuing technical reports that disclose information about exploration or other mining properties to the public in Canada are governed by a number of securities regulations.

May 10, 2014

The discussion in this paper centres on examples of mining that are drawn mainly from the coal mining industry. The intention is to review the opportunities that exist for incorporating environmental planning into mining industry practice in New Zealand. The coal mining examples serve to make some general points which have some application for many types of mining.

Jan 1, 1981

By S F. Simmons, J Fleming

Alteration and mineralisation at the Island Copper deposit is related to the intrusion of Early Jurassic quartz feldspar porphyry dykes into surrounding comagmatic Bonanza volcanic rocks. The pyrophyilite alteration zone forms an upward flaring cone, largely hosted within a breccia body that cross-cuts the Co, Mo, and Au-rich ore shell. This alteration zone contains pyrophyllite, dumortierite and diaspore and resembles alteration occurring in some high-sulfidation deposits, but which is barren. Fluid-mineral equilibria and fluid inclusion studies indicate formation at approximately 300 ¦C from fluids dominated by steam and gases. These fluids appear highly acidic, but sulfur poor, leading to extreme base leaching within the breccia body and surrounding rocks.

Jan 1, 1995

By N. Krishna

The utilization of Electrochemical Impedance Spectroscopy (EIS) in conjunction with Atomic Force Microscopy (AFM) is a powerful surface characterization technique to study the role of sulfur formation during acidic oxidation of chalcopyrite. It has been established that the chalcopyrite dissolution kinetics is controlled by the formation of passive sulfur layer during leaching. The objective of the study was to characterize the intermediate sulfur layer formation at different oxidation conditions in acidic solution. The chalcopyrite samples were subjected to anodic oxidation and the oxidation process was analyzed using impedance spectroscopy. The sulfur growth on the chalcopyrite surface during oxidation was further analyzed using Atomic Force Microscope for sulfur roughness and grain size, peak height and sulfur growth.

Jan 1, 1999