Search Documents

By Christopher J. Bambridge, Lee Seng Hoor

The Stormwater Management and Road Tunnel (SMART) Tunnel is a world first in the use of tunnel space transmitting both road and water through the same spatial envelope. The unique aspect of the SMART project is that the highway decks are used periodically for the conveyance of water. This aspect of the project has posed its own technical challenges that have been overcome in the design stage of the work allowing the project to be taken forward to construction with confidence in the systems to be Installed in the tunnel.

Jan 1, 2005

By H. J. de Haan, J. van Lookeren

In view of their size and favorable characteristics, Shell's heavy-oil fields on the eastern coast of Lake Maracaibo, Venezuela — known as the "Bolivar Coast" — are obvious candidates for the application of thermal recovery methods. During the last decade various methods have been tested, such as steam drive,', steam soak and in-situ combustion.3 Steam soak was discovered as a promising production method rather accidentally in 1969, during early steam drive testing in the Mene Grande Tar Sands1 When steam erupted at the surface due to breakdown of the overburden, the injection wells were back-flowed to relieve the reservoir pressure. This resulted in high oil production rates, all the more impressive because the reservoir is unproducible by primary means. It was concluded that injection of limited amounts of steam might be a very effective method for stimulation of heavy-oil wells. To obtain information that would be more widely applicable, testing of the process was continued in the eastern part of the Tia Juana field (Fig. 1). Here even more favorable results were obtained than in Mene Grande. This created sufficient confidence to prompt a large-scale project, which was considered essential for an adequate evaluation of ultimate recovery, steam requirements, mechanical problems and economic prospects. To obtain an early answer on the ultimate recovery a fairly depleted area was selected in the western part of the same field ("A" in Fig. 1). The first steam was injected in March, 1964. This paper describes the performance until the end of 1966. The production mechanism and well inflow performance are discussed in some detail. In view of the favorable results obtained so far, steam soak operations have expanded considerably since the start of this project. Presently, five other projects are under way, of which two are about the same size as the one under discussion, with further extensions being programmed. Description of the Project Reservoir Data Shell's part of the Main Tia Juana reservoir has a proven area of 8,800 acres and an average net oil sand thickness of 130 ft. It contained an initial quantity of 2,750 million bbl of stock tank oil (STOIIP), with an API gravity ranging from 10 to 15 API and a viscosity of 100 to 10,000 cp (at 122F). As a geological unit it is known locally as the Lower Lagun-illas member of the Lagunillas formation, which is early Miocene in age. The sand bodies are believed to be distributary channel sands deposited in a lower coastal plain. Most of the channel sands have lateral and some vertical communication. The field was developed mainly in the period from 1936 to 1950. The ultimate primary recovery is estimated at 18.1 percent of STOIIP, of which 12.5 percent STOIIP had been produced by the end of 1963 from some 540 wells. By then the average pressure had decreased from an initial value of 960 to 550

Jan 1, 1970

By A. Takala, B Nielson, J. Schunicht

"Pre-concentration in minerals processing presents clear advantages in energy efficiency, water efficiency, reduction of consumables and minimization of capital and operating costs. Outotec’s sorting solutions are powered by Tomra Sorting in order to achieve pre-concentration of concentrator feed in a variety of mineral processing applications. Sensor based sorting combines advanced sensors with rapid computational evaluation and mechanical separation of valuable material from waste and/or gangue. Modern sensor based sorting machines typically use fine air jets to propel individual rocks, thus optimizing recovery and minimizing “mis-sorting”.Gold is generally present in such low concentrations that sensors suitable for ore sorting cannot directly detect it. Therefore, in order to sort gold ore, properties of associated host rock are used. Free and sulphidic gold is often hosted on the quartz-host rock contact zone. Laser scattering effect can be used to detect the surfaces of quartz and composite quartz-host rock particles for subsequent sorting with very high recovery of 95 to 99%. In addition, ore often preferentially fractures along the quartz-host rock contact zone in the crushing circuit. This behavior helps because it liberates more quartz for detection.The feasibility of sorting is investigated for four gold projects in Northern Europe with similar mineralogy. This includes geometallurgical evaluation, amenability testing, small scale “mini-bulk” factory testing in full scale sensor based sorting. The results of the various tests are presented and basic feasibility demonstrated with information on flow sheet development. In addition, the amenability process is evaluated and recommendations made for future projects."

Jan 1, 2017

By J. M. Davidson

The potassium mineral polyhalite (K2SO4.MgSO4.2CaSO4.2H20) found in large deposits in western Texas and southeastern New Mexico is associated with varying amounts of halite (sodium chloride, NaCl) and anhydrite (calcium sulphate, CaSO4). Although the anhydrite, because of its low solubility and slow rate of solution, is relatively inert, the halite is dissolved immediately in any process solution with which the polyhalite comes in contact. Limited quantities of sodium chloride in the liquors used for the hot extraction of polyhalite materially improve the results obtained,4 but only a very small sodium chloride content may be desired in the entering polyhalite in other procedures, such as Bureau of Mines process 75. In. all of the processes suggested for the recovery of potassium sulphate from polyhalite the control of the sodium chloride content will be desirable, if not absolutely essential to efficient operation. OCCURRENCE OF HALITE IN POLYHALITE A preliminary estimate of the amount of halite associated with typical deposits of polyhalite may be derived from drill cores, although it should be remembered that only 50 or 60 core tests have been made in the many hundreds of square miles of the Permian basin. From a mineralogical study of 41 of these cores, Schaller and Henderson6 state: In many of the sections of core that seem when viewed by the unaided eye to consist essentially of polyhalite, both halite and anhydrite are present in greatly varying quantities - with very minor quantities of clay and magnesite.

Jan 1, 1934

By Patrick Frenette

The Goldex Mine is an underground gold mine using a unique mining method where a single very large stope is being created. In order to maintain stability of the walls and roof of the stope which is 450m, 250m high and up to 120m thick, ore is left in the stope as long as possible and acts as backfill would do. At many occasions during the mining sequence, the walls will be exposed on height ranging from 30 meters up to 250 meters. A monitoring system comprising in-stope laser surveys, a seismic system and an array of extensometers and sloughmeters all remotely connected to surface is used to observe the shape and evolution of the stope. This paper will focus on the results obtained following some of the large blasts and on the long term monitoring of the stope.

May 1, 2011

By D. Bogunovic

The U.S. coal mining industry consumes a significant amount of energy, primarily diesel fuel and electricity. The continuous global increase in energy demand, high energy prices, and environmental issues related to carbon dioxide emission represent a substantial challenge for the mining industry. This paper presents a result of research work on development of an integrated data environment system for analysis and control of energy consumption in a surface coal mine. A case study on an operating surface coal mine is carried out to demonstrate the practical application of the developed system. The research work presented here may be used by mining professionals to help provide the answers to the crucial questions of when, where, and how much energy is being used. This developed system represents a framework for efficient management of energy consumption. Key words: surface mining, coal, energy consumption, Information System.

Jan 1, 2009

A pyrite flotation concentrate assaying 0·065 oz/ton gold was investigated to determine the mode of occurrence of the gold. Ftom cyanidation and acid leaching experiments it was concluded that O· 02-0· 03 oz/ton goldwas in solid solution in pyrite and the balance of the gold was finely dispersed as grains throughout the pyrite.Autoradiography and electron-probe examination of possible areas in briquetted concentrate did not detect any grains of gold. Neutron irradiation and gamma spectrometry confirmed on 100 mg samples the fire assays obtained on 1 assay ton samples.Oxidation to hematite and reduction to magnetite at 600°C made practically the whole of the gold extractable by cyanide. This technique could be of major significance for gold ores which contain a substantial amount of "refractory" gold.

Jan 1, 1969

By C. A. Geffen

This report, sponsored by the U. S. Bureau of Mines, presents the results of an examination of the safety of the impactor shaft sinking system in comparison to conventional shaft sinking technology. Detailed study of the impactor system was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the impactor machine and its support systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates measures of both the frequency and the potential consequence of accidents. A safety evaluation of the com¬ponent operations of the impactor shaft sinking system was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that the impactor shaft sinking system is safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by an average of over 35 percent with use of the impactor shaft sinking system. Design change recommendations to further improve the safety of the impactor system include a revised fire suppression system, improved access to and from the operator cabs, reliable noise attenuation measures and improved communication systems. An operational safety manual was also developed for the impactor shaft sinking system.

Jan 1, 1982

By N. Sutcliffe

Refractories and slags play a vital role in the production of stainless steel. They are in intimate contact with the steel at temperature, and chemical reactions between the three can and do occur. These interactions can be beneficial, in the case of active tundish and ladle slags, and negative in the case of refractory erosion and slag entrapment. This paper presents the results of both plant trials and laboratory investigations of steel/refractory and slag/refractory interactions. The interaction mechanisms observed are described leading to selection criteria for new refractory products. Keywords: slags, steels, refractories, reaction mechanisms.

Jan 1, 2004

By H. M. Lewis

The current status of the international zinc market is summarized, and a supply /demand outlook is presented for the next five years. A number of technical problems facing the industry are outlined. Introduction ZINC has sometimes been called the unknown metal. Considering that on a world basis it ranks third among non-ferrous metals in production and consumption, zinc retains a certain modesty. It has no distinctive colour like copper, lacks the low density of aluminum or magnesium and is not always easy to identify as a product. The 'spangle' of galvanized steel is probably zinc's most distinguishing feature. The purpose of this article is to develop an over-all review of zinc. Starting with the current position of the metal, the major factors that will shape its future will be described so that an assessment of the outlook for zinc can be made.

Jan 1, 1978

By Amauri Garcia, Noé Cheung, André dos Santos Barros, Clarissa Barros da Cruz

Embora a resistência ao desgaste seja geralmente a principal propriedade avaliada decorrente da adição de terceiros elementos em ligas Al-Sn, não somente os fenômenos tribológicos são responsáveis pela deterioração gradual das peças, mas também os fenômenos relacionados à corrosão. Dessa forma, o presente estudo objetiva analisar o efeito de características microestruturais formadas durante a solidificação transiente da liga Al-9%Sn-5%Zn na resistência à corrosão em solução 0,06M NaCl investigada por polarização potenciodinâmica e espectroscopia de impedância eletroquímica. Foi observada uma morfologia microestrutural caracterizada por dendritas da fase α-Al com concentrações de Zn tanto na matriz dendrítica quanto em regiões ricas em Sn localizadas nos contornos interdendríticos. A evolução dos espaçamentos dendríticos primários (λ1) também foi correlacionada com parâmetros térmicos de solidificação. Finalmente, constatou-se que a amostra com microestrutura mais grosseira, ou seja, λ1 = 89,6 μm, apresentou comparativamente menor densidade de corrente de corrosão e maior resistência à polarização.

Oct 1, 2019

By Hargraves A. J, Smith J. W

Experiments conducted at Tahmoor Colliery, Sydney Basin, have demonstrated the variability in chemical and isotopic composition of seam gases issuing from boreholes in the Bulli seam and desorbing from lump coal from the same source.From this work it appears that an immediate preferential release of methane accompanies the physical disturbance of the coal seam by penetration with development or drilling or by detachment. In addition, both early released methane and carbon dioxide are depleted in 13C relative to later desorbed gases, therefore the analyses of gas samples taken after such events may not reflect the true bulk composition of the undisturbed seam gas in situ. A method for overcoming this problem by taking gas samples at depth in the "steady state" is proposed.

Jan 1, 1987

By Zeljka Pokrajcic

Crushing and grinding, or comminution, circuits are the most energy intensive process of a mineral processing plant. Comminution involves the physical size reduction of an orebody to a particle size sufficient for recovery of the mineral values. However, the comminution process remains inherently inefficient. The inefficiency is a result of the operating nature of comminution devices such as grinding mills, where transfer of energy between grinding media and particles in unconstrained and completely random. New comminution circuit design strategies are presented in this paper. The aim of the new strategies is to improve the overall efficiency of the comminution process and reduce the total energy consumption of a comminution circuit. The energy efficient strategies include the: ? rejection of coarse size liberated gangue from the comminution circuit and further downstream size reduction ? use of more efficient grinding and crushing equipment ? the selection of coarser particle product sizes to alleviate the increased energy intensity required to achieve finer product sizes Singularly and when combined, these energy efficient strategies can significantly decrease the overall energy consumption of a comminution circuit. This paper also explores the financial impact of certain energy efficient strategies using an analysis tool called EcoNomics?. It shows that substantial financial gains can be made by including more efficient technologies and methods in comminution circuit design.

Jan 1, 2010

By Robert G. Harris

During the last five years there have been significant improvements in face support monitoring techniques particularly in respect of face pressure. The measurement of support loading pressures was originally conceived as a maintenance aid for the hydraulic systems but recent work has also included geological loading displays of the complete face as well as individual supports. This paper briefly examines the means of obtaining this information, together with some examples of actual face data. Also included is a summary of the benefits of such monitoring and an outline of future development work.

Jan 1, 1993

By A. B. Hazar-Yoruç

Ferrochromium produced by smelting chromite ores is an important alloying component in the steel industry. Ore, coke and fluxes are mixed and reacted in an arc furnace for a smelting process of ferrochromium. In ad-dition to this process, pre-reduction of chromite ore with carbon is an important industrial process. In all these processes, the mechanism and kinetics of reduction of chromite with carbon play an important role. In this study, the reduction of Turkish chromite ore with carbon was investigated. Chromite and carbon were ground to three different particle size groups. Chromite was mixed with carbon in stoichiometric and excess ratios. The samples were reduced under argon atmosphere at temperatures between 1,200° and 1,350°C. The formed phases and alloy compositions of reduced chromite samples were analyzed by optical microscopy, scanning electron microscope (SEM) with EDAX and X-ray diffraction analysis (XRD). Experimental results showed that the degree of reduction and the reduction rate increased with increasing temperature and decreasing particle size. The highest degree of reduction, 61.4%, was obtained at 1,350°C. The reduction took place in three stages: Stage 1: transformation of Fe3+ to Fe2+ and formation of metallic nuclei, Stage 2: formation of metallic crust around the particles and Stage 3: growth of the metallic crust and coalescence of the metallic phase.

Jan 1, 2007

By Bruce Hebblewhite

This paper focuses on the recent achievements and practices developed through the Minerals Tertiary Education Council (MTEC) initiative of the Minerals Council of Australia (MCA), in conjunction with the three partner universities involved in mining engineering education – University of New South Wales (UNSW), West Australian School of Mines, Curtin University (WASM), and University of Queensland (UQ). The collaboration between these partner universities and industry has led to the development of shared course material, cross-institutional teaching arrangements, and development of a number of flexible, distance-based delivery programs. The paper will then move on to future initiatives. Importantly, the exciting challenge is the future initiative planned to cement this collaboration by the formation of a “virtual” national school of mining engineering – Mining Education Australia (MEA). This will provide a common 3rd and 4th year program to all three universities from 2007, involving innovative teaching and learning arrangements, greater student exchange potential and a more significant input by industry into the education process. Such an initiative is not without its challenges, and has a long way to go, before becoming a reality. However, it offers greater attractiveness and marketing potential to prospective students, as well as economic efficiencies, whilst delivering a better quality, and hopefully greater quantity of graduates to industry. It can also form a launching platform for a much greater level of international collaboration, through a proposed International Mining Education Network (IMEN) which is currently being floated amongst a number of international educators.

Jan 1, 2005

By Reinhardt Thiessen

Views and conceptions of the origin, composition, and general nature of coal differ so widely that to determine the real extent of actual knowledge is no easy matter. The chemist finds difficulty in attacking the chemical problems and the engineer lacks a broad chemical basis for the study of his problems. Thus the economical and efficient utilization of coal in the industries suffers from a lack of knowledge of the composition of coal itself. Most scientists interested in this matter, as has been brought out in discussions during the recent investigation of coal problems, appear to have only a vague idea of the components of coal and their origin. Some are even in doubt as to whether substances derived from the wood and resins of plants form a part of coal; and few seem to have more than the dimmest idea of what are the components of coal, the condition in which these now exist, and the transformations that they haye undergone. Although during the paiilt century or more many co.rrect observations have been made and recorded, these were falsely or inadequately interpreted, so that many of the interpretations rendered are contradictory. As a result there has been great confusion. Many of the observations made in the past, although accurate and correct, could not be explained, because the principles involved in a correct solution of the problem were not then known. For example, Parkinson, Hutton, Petzhold, Guembel, and others made valuable discoveries regarding the processes by which plant substances are transformed into coal, but as the principles involved are those of colloidal chemistry, a science not known to the scientific world of that time, the observed facts could not be interpreted and the solution of the whole problem was blocked. The explanation of the true meaning of the alternating bright and dull bands so familiar in all ordinary bituminous coals afforCls another example. This banding has been observed and recorded from the earliest times, and has led to the forming of many false theories. Some gAologists, for example, have endeavored to explain the bands as due to alternating climatic conditions during the coal-forming period. Had the geologists known the true nature of coal they could not have made this mistake nor many others made in the past. To fill in a few of these gaps and to clarify some of the existing confusion is the aim of this paper. The immediate cause that led the author to investigate further the composition of coal and the origin and structure of its constituents was that when an attempt was made to discover the meaning of the coking and noncoking properties of coal a more exact knowledge of the nature of coal was required than was then available.

Jan 1, 1920

By G. R. Fitterer, E. A. Krockenberger, B. E. Sockman, R. B. Meneilly, J. F. Eckel, E. W. Marshall

"Steel manufacturers have noticed a decided tendency on the part of many of their customers to become more exacting in their steel specifications. Under these conditions, the steel must not only meet the specifications of physical properties (tensile strength, reduction of area, elongation, impact strength, grain size, normality, etc.) and the chemical analyses, but must also pass the inspection test of ""cleanliness.""By cleanliness is commonly meant the absence of oxide and sulphide inclusions. Other foreign particles such as furnace or ladle slag, ladle and runner brick, etc., must also be absent. The determination of cleanliness at present is usually made by microscopic inspection or macroetching.The rejection of steel for lack of cleanliness is increasing, out cleanliness is one of the most difficult requirements for the manufacturer to fill. The reason for this is that every steel inspector has a different conception of a. clean steel. A material which does not pass the examination of one inspector way be regarded as entirely satisfactory by the metallurgist of an¬other company. The cause of this confusion and disagreement concerning the definition of a clean or a dirty steel is simply that as yet no standardized procedure for the determination of impurities has been proposed and generally accepted, since many variables are encountered which interfere with the development of a satisfactory method. An idea of the complexity of this situation will be obtained from the following pages.A Survey of Proposed Analytical MethodsAlthough no analytical method has been accepted, many procedures have been proposed, as may be seen in Table 1. Therein are listed 16 of the better-known processes, pith references to the work of their originators, their mechanisms of determination, and their applicabilities. Among these is included the electrolytic method developed by one of the present authors, and some comparison between this and previously proposed procedures may be obtained by a study of the table. It appears that this new method Las many advantages over the others, and this paper presents a critical Study of its value."

May 1, 1933

By Irving Hartmann

[The explosability of coal dusts has been the subject of many investigations studies have been conducted in laboratories, in galleries and in coal faire; of several countries to obtain information on the causes, development, and prevention of mine explosions. Early laboratory experiments on it American colas dealt with pressures developed in test bomb by explosions of dust clouds and with, the effects of gas in the dust atmosphere.5/ Later, the emphasis shafted to evaluation of the relative fleet flammability and the ignition temperatures of coal dusts.6/ Much worthwhile effort was devoted to the development of Laboratory apparatus and test procedures that gave good correlation with large-scale explosion tests in the Experimental cost mine. In recent years a number of special problems were studied, mostly with bituminous Pittsburgh coal dust]

Jan 1, 1954

By R. L. Virta

Common clay is a natural, fine-grained material composed of hydrous aluminum silicates. Shale is a laminated sedimentary rock that is formed by the consolidation of clay, mud or silt. Production About 160 companies produced common clay and shale in 41 states. In states not reporting production, common clay and shale probably was mined and sold for construction applications by companies not participating in the U.S. Geological Survey’s canvass of producers.

Jan 1, 2005