Search Documents

By R. J. Visintainer, W. L. Whitlock

"Difficulties with the sizing and operation of centrifugal froth pumps are common and the underlying fluid dynamics are complex. Design and selection often relies on previous experience, offering unreliable guidance for novel applications or unexpected problems. The current paper describes a program of extensive laboratory testing on froth handling centrifugal pumps, covering a range of flows, heads, speeds, viscosity, air content and froth stability. Variations in impeller vane design and the effectiveness of an airlock venting apparatus were also examined. The program resulted in a better understanding of centrifugal froth pump dynamics and insight for the troubleshooting of field applications.INTRODUCTION The Challenge of Pumping Froth In pumping mineral processing froth, the handling of large quantities of air within the fluid is often unavoidable. Efforts to reduce the amount of air present at the pump suction, while always recommended for improving pump performance, may have limitations. Some strategies may also carry an economic penalty, such as unwanted process dilution (e.g. due to water spray or injection), or increased capital cost of equipment due to oversized pumps, sumps and/or piping. Froth pumping losses fall into several categories, as described below and represented graphically in Figure 1. • Density effects: Entrained air reduces the pressure created by the centrifugal pump in direct proportion to the reduction in bulk density. This is not a true “loss”, since the head produced by the pump (in meters of froth), may remain unaffected. However, the reduction in pressure often leads to a corresponding increase in pump speed required to drive the system, which itself leads to increased NPSH required by the pump (NPSHR). Furthermore, by adding a gas phase, the overall volumetric flowrate is increased, assuming a fixed quantity of de-aerated liquid being handled. This leads to increased suction velocity which further reduces the NPSH margin by simultaneously increasing pump NPSHR and decreasing system NPSH available at the pump suction (NPSHA). • Viscosity effects: Increased viscosity introduces an additional factor in some froth pumping applications, such as oil sands bitumen froth. Losses result from increased shear stress within the fluid flow, which increase with flowrate. Viscosity also facilitates the formation of airlock by reducing turbulence and allowing individual bubbles to coalesce more easily within the flow stream. Finally, it increases pump NPSHR by increasing local pressure drop in the vicinity of the vane inlet edges. • Airlock effects: Also known as air binding, it occurs when air or gas coalesces within the pump suction or impeller passages and begins to collect there, held by buoyancy forces within the rotating flow field. In essence, the liquid “floats upwards” towards the pump suction against the outward directed centrifugal forces. The airlock acts as a blockage, with corresponding reductions in flow, head and efficiency. NPSHR also increases, due to increased velocity and distorted streamlines in the flow circumventing the blockage."

Jan 1, 2012

By D. Nutakor

The ability of computers to create synthetic representations of the real world in virtual reality offers a number of opportunities to enhance training methods used in the mining industry. Unfortunately, the training effectiveness of virtual reality systems currently used in the mining industry has received only limited testing. Miner Simulation (MinerSIM), an augmented reality system with integrated hypermedia suitable for training underground miners in the basics of using a jackleg drill to install rock bolts in a virtual mine environment is in its evaluation process at the University of Missouri-Rolla Experimental Mine. This paper discusses evaluation methodologies of the MinerSIM system, which consists of experimental and control groups with control students learning via traditional lecture and text formats. Preliminary results from usability tests of the first part of MinerSim, which is an online tutorial on underground rock bolting, are presented.

Jan 1, 2008

By Jerry Wallace

This project consisted of blasting for expansion of a major interstate natural gas transmission pipeline pump station. The pump station handled 400-500 million cubic feet (1 l- 14 million cubic meters) of gas per day.

Jan 1, 1996

By H. Sato, B. Thornton, K. Nishi, A. Usui

"Northwestern Pacific submarine seamounts are believed to be future marine mining areas of ferromanganese crusts, which contain hi-tech industrial metals, such as Co, Ni, Te, Ti, Pt, and REEs. The Takuyo No. 5 seamount is a member of the Cretaceous super-plume seamounts in the north Pacific, located within a Japanese EEZ (100 nm from the Minami- Torishima Is. or Marcus Is.), and only 300 nm away from the Japan’s Licensed area for exploration of Co-rich ferromanganese crusts under the ISA. This is an on-going program supported by independent academic communities but not a state-run program or managed by private funding.We have observed, sampled, measured, and analyzed the occurrences, distribution, physical properties, and microbiological environments at a selected flat topped seamount named Takuyo No.5 as a model area for scientific study of ferromanganese crusts within the Japanese EEZ. We then characterized crust structures, composition, age, and growth history, resulting in an understanding of the overall nature and distribution of these deposits from wide range of areas, water depths and geological environments. The study started with a ROV (Hyper-Dolphin 3K of JAMSTEC) exploration jointly with universities and national institutions (Japan Agency for Marine-Earth Science and Technology, Japan Oil, Gas, and Metal Exploration Corporation, and Geological Survey of Japan) in 2009 using marine geology vessels, remotely-operated vehicle, an oceanbottom drill machine, deep-tow TV camera, as well as conventional dredges and corers. We have been studying the topography, geology, nature of the bottom material of the seamounts using delicate sampling devices and measurement tools, and characterized the distribution patterns of the metal-rich ferromanganese deposits from chemical, mineralogical, and microbiological points of view."

Sep 1, 2014

By F F. Pitard, K J. Ehrig

The Olympic Dam iron-oxide copper-gold (IOCG) uranium-silver deposit is second in size only to Norilsk, the gigantic metalliferous deposit. Olympic Dam is the largest publicly declared uranium, fifth largest copper and third largest gold resource. The deposit is typified by texturally destructive brecciation and intense iron metasomatism of the Roxby Downs Granite, bedded clastic facies rocks and mafic-ultramafic dykes. The deposit contains over 100 minerals. Copper mineralisation consists of chalcopyrite, bornite and chalcocite. Uraninite, coffinite and brannerite are the dominant uranium-bearing minerals. Gold mineralisation consists of electrum, tellurides and Au-Cu alloys. Hessite is the major silver-bearing mineral. The economic minerals are disseminated throughout the breccia matrix where the average grain sizes of the Cu-sulfide, uranium, gold and silver minerals are ~50, 20, <5, <5 microns, respectively.A significant number of sampling theory-based test programs have been completed since the mid-1990s to establish sampling nomographs, select appropriate sampling (ie split versus chip and interval lengths) and sample preparation protocols, quantify the errors associated with each subsampling stage, determine the practical uncertainty limits of Olympic Dam matrix-matched standards, and identify improvement opportunities related to the ongoing assaying quality assurance / quality control (QA/QC) program. Invaluable knowledge and unexpected insights gained from sampling studies at Olympic Dam have helped to improve our understanding of the distribution of economic and deleterious elements within the Olympic Dam deposit.CITATION:Ehrig, K J and Pitard, F F, 2017. Underground bulk sampling, uniform conditioning and conditional simulation – unrealistic expectations?, in Proceedings Eighth World Conference on Sampling and Blending , pp 21–28 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By B. P. Faulkner, M. Weinecke

Svedala started a development program in 1997 to develop a process to convert waste tires into valuable commodities. A review of numerous approaches revealed short-comings in the various approaches either process, mechanical, combination of factors, or trying to emphasis the production of low value products. A market study revealed that a process that could produce a good grade of carbon black would be economically feasible. This paper discusses the laboratory and pilot plant development and commercial plant design.

Jan 1, 2001

By T. H. Eyde

Worldwide production of natural zeolites during 2001 was estimated to be about 3.5 Mt (3.85million st). Construction and agriculture continued to be the major consumers. Estimated production in North America during 2001, including the United States, Canada and Mexico, was about 40 kt (44,000 st). In the United States and Canada, the zeolitic tuffs are ground, extruded or modified for use as adsorbents, desiccants, ion-exchange media and carriers. In Mexico and the rest of the world, the zeolitic tuffs are cut into dimension stone that is used in construction. Zeolitic tuffs are usually composed of the minerals clinoptilolite, mordenite or both. They occur in a variety of colors and are easy to cut and shape. And they have low thermal conductivity. This construction application is classified with dimension stone rather than with chemical and agricultural uses.

Jan 1, 2002

By Slechta J. J

An evaluation of a pilot scale Delkor horizontal belt filter at Bellambi's South Bulli Colliery showed high productivities and low moisture contents for a range of feed slurries. When treating flotation concentrate, a productivity in excess of 1000 kg/m2/hr (dry) at a moisture content of less than 22 per cent was obtained. The results indicated the belt filter had a capacity twice that of conventional drum or disc filters, and was capable of dewatering a very fine, thickened, classifying cyclone overflow slurry to an acceptable moisture content. The superior performance of this filter is discussed in terms of the factors influencing cake formation and the stratification of solids in the filter bowl of a conventional rotary vacuum drum filter.

Jan 1, 1986

By G Baiden

The removal of rock blockages in mining operations has long been a risky undertaking, especially in high overhead conditions. Moreover, the assessment of where to put charges and the placement of them has been difficult due to the lack of visibility and safe access to the area. Traditionally, wedging long poles with explosives on them to keep the operator at a relatively safe distance has been the tried and true method of attempting to remove the blockages. Unfortunately, this is not a perfect system as it usually takes several attempts to remove the blockage. Each successive attempt results in even more dangerous conditions for workers and/or damage to the mine due to the successively larger amounts of explosives used until the hang-up finally comes down.Over the years, different ideas have been proposed to improve this process and reduce the inherent safety risks. Some of the technologies that have been trialled include projectiles fired at the hang-up; large, cumbersome arms; and massive amounts of explosives, each of which come with their own inherent safety risks that result in dangerous situations for miners and the mine.After gaining a thorough understanding of the process, Penguin Automated Systems Inc has developed a robotic system that is capable of working in a rock blockage safely. The idea combines the latest in telerobotics technology with 3D scanning and underground geospatial positioning. The hang-up removal is performed by scanning the inside of the hang-up to rapidly develop a geospatially placed 3D model for the operator to use. The 3D model is detailed enough that the operator can attempt to pick the ‘keystone’. A blasting engineer or the operator can then determine the exact position where the explosive charge should be placed in the 3D model and thus at the actual hang-up. The operator, controlling the robotic arm, uses the 3D virtual reality model of the robot system and the actual drawpoint information model to display the location information, the arm can then reach into the hang-up to position the charge using the kinematic model of the robot system. The 3D model is used to provide views inside the hang-up so that the operator can move the arm safely and precisely. This process allows the operator to place the charge (using the 3D representation of the drawpoint) from a long distance away. As the process continues, the end of the arm drills the rock and precisely loads the explosives. The robot then returns the blasting cable to the command station, which is located in a truck at a safe distance from the blockage.This paper will review the development of the system and present the results to date.CITATION:Baiden, G, 2016. Robotic hang-up assessment and removal of rock blockages in mining operations using virtual reality for safety, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 745–754 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Cristiane Sales Gonçalves

O processo de injeção sob pressão de ligas de alumínio é empregado para a produção de peças diversas, destinadas principalmente à indústria automobilística, com a possibilidade de produzir peças complexas, contendo seções delgadas, e a alta velocidade de produção. O reduzido tempo de ciclo e as elevadas temperaturas envolvidas promovem danos por fadiga térmica na superfície de trabalho das matrizes, que crescem com o aumento da produção até atingirem condições que inviabilizam o uso da matriz. O presente trabalho visou estudar o efeito da nitretação na superfície do material, relacionando-o aos aspectos microestruturais e tensões residuais inseridas durante nitretação. O aço AISI H13, foi tratado para dureza de 45 HRC e posteriormente nitretado sob plasma em diversas condições de temperatura, tempo e composição da atmosfera gasosa. Os resultados obtidos mostraram que as variações dos parâmetros de nitretação afetam os perfis de dureza e de tensões residuais presentes nas camadas nitretadas, bem como os microconstituintes das mesmas. O material nitretado, após ser submetido a temperaturas da ordem de 600°C, apresentou redução no nível de tensões residuais de compressão, ocorrendo processo de alívio de tensões. O mesmo efeito não foi tão fortemente verificado no perfil de dureza do material.

Aug 8, 2018

By T. Gammatikopoulos, C. Gibson, M. Aghamirian

Lithium is an alkali metal found in brine deposits in the United States, Chile and Argentina, as well as in hard rock deposits in Australia and North America. In hard rock deposits, spodumene (LiAl(Si2O6)) is the major economic lithium bearing mineral. Spodumene is typically upgraded through a combination of dense media separation, flotation and magnetic separation. One of the major spodumene concentrate quality specifications is the iron oxide content because it will help determine if the concentrate is considered ceramic grade for use in ceramics and glass or chemical grade for use in lithium ion batteries. The rejection of iron bearing silicate minerals from artificial ore composites (high amphibole and low amphibole, high quartz/feldspar) from a hard-rock spodumene deposit was investigated using magnetic separation and flotation. The efficacy of Wet High Intensity Magnetic Separation (WHIMS) in iron rejection was found to be dependent on the mineralogy of the iron-bearing silicate minerals including modal distribution, liberation and association. When magnetic separation was conducted prior to flotation, the Fe2O3 grade in the final flotation spodumene concentrate was reduced from ~3% to ~1% Fe2O3 , and improved lithium recovery in flotation was observed. It was determined that it was most effective to conduct WHIMS on the flotation feed after scrubbing and de-sliming because this reduced the required magnetic field to recover iron-bearing minerals, likely because slime coating was greatly reduced. Flotation collector screening of four different collectors with varying rosin acid content demonstrated a potential increase in selective flotation of spodumene over some iron silicate minerals with decreasing rosin acid content in the fatty acid collector. However, due to marginal difference in flotation results with the various collectors tested, further testing is required to confirm the observations made and establish a hypothesis regarding the effect of rosin acid content.

Jan 1, 2017

By John J. Sammarco

The U.S. Bureau of Labor Statistics reports that the mining industry has the highest average annual fatality rate (31.9 per 100,000 workers) among all major American industry. To address this, a major research program to reduce hazard exposure of miners with computer-assisted mining equipment was initiated by the U.S. Bureau of Mines.1 One application involves the manual process of extracting and hauling coal where operators, in the tight confines of a mine, can be struck or caught by mobile machinery. The approach to remedy this problem uses a guidance system on the haulage equipment so that it follows the machine that extracts coal. This, in essence, involves sensor-based docking of the machines. Sensors that can survive the hostile mine environment of dust, methane gas, and water, play the key role. Computer analysis of the mining machine's movements and empirical machine characterizations were conducted to establish operating requirements and spatial limitations to ensure proper loading of coal into the haulage equipment. These data served in the selection of a sensing system. Various technologies such as scanning laser systems and ultrasonic sensors have frequently been used in other applications but were found unacceptable. However, a near infrared (IR) sensor employing active targets met the requirements. The sensor has a nominal 75° conical field-of-view and a range from 0.1 to 18.0 m. For the single target mode, nominal range accuracy was 4.3% at a distance of 3.56 m. Correction algorithms were generated reducing the error to 0.6%. Airborne dust testing showed less than 0.8% accuracy (worst case) degradation at levels exceeding (by a factor of 7.5) concentrations permitted by Federal law. The sensor can track multiple active targets providing five degrees-of-freedom (DOF) measurements. Using four targets, the nominal range accuracy was 0.4% without correction algorithms. A guidance system for the haulage system to follow the mining machine does not exist commer¬cially. Such a system can reduce fatalities and injuries by current haulage mining equipment, and is a viable alternative to current haulage control.

This paper endeavours to lay as concisely as possible, before the members the salient features of local gold milling practice, and to point out in what respects this practice differs from that of other large mining camps. This is essentially a free milling ore the gangue being quartz and the gold occurring in a coarse form. At times the ore crushed contains a good deal of slate, the latter imparting to the tailings a somewhat leaden hue.Small amounts of sulphides, chiefly iron pyrites, and at times smaller quantities of arsenical pyrites, zinc blende, and galena are contained in the stone. The average amount of sulphides contained in the ore cannot well be ascertained, as the concentrate obtained in all cases contain too much silica to form a basis of calculation...

Jan 1, 1902

By A Palynchuk

The development of welded pipe has paralleled the general industrial development and, in particular, that of the petroleum industry. The petroleum industry's need for high-grade, economical pipeline material to make many 'of its projects feasible has been a significant factor in the development of light-wall, high-grade welded pipe. The modern welding processes, such as high-frequency, electric resistance, flash, submerged arc, etc., have some basically different characteristics. The modern high-frequency weld mill is a complex of specialized equipment that is integrated into a production unit. Each component in the unit performs a specific function in the production process. Quality control must be built into the process on an operating basis and, to maintain the quality required for pipeline standards, must be more than a policing operation. The further development of the welded pipe industry will be determined by changing and increasing demands. The technical and economic views and requirements that will influence the development have to be resolved.

Jan 1, 1964

By Tiago Ramos Ribeiro

Os processos de redução direta utilizam-se de gases redutores (CO e H2) para redução do ferro e produção do DRI. A geração deste gás se dá através de reforma de metano que pode ser feita em um reformador, ou dentro do reator de redução com o DRI como catalizador. O último caso ocorre nos processos auto reformadores. A cinética da reforma de metano com H2O catalisada por DRI foi estudada em temperaturas entre 875°C e 1050°C. Os resultados mostraram que até conversão de metano de 0,50, a reforma é controlada por reação química catalítica conforme mecanismo proposto por Münster e Grabke(3,4). Acima desta conversão, o mecanismo não foi determinado. O uso de gás com potencial abaixo do limite para carburação (CH4/H2O < 1) resultou em DRI sem carbono. Com gás de potencial igual ou acima do limite, a carburação do DRI ocorreu e no caso do gás similar ao do processo industrial a carburação impediu a reação catalítica de reforma.

Oct 30, 2017

By A. M. Ramalho

In the synthesis and sintering processes to obtain superhard materials, such as diamond and cubic boron nitride, deformable ceramic capsule is used as gasket to transmit and support the required high pressures and high temperatures, HPHT. The ceramics materials for these capsules should have special physics and chemical characteristics such as refractoriness, shear strength and compressibility. In this work, Bridgman?s anvil made of hard metal or speed steel was used to characterize some ceramics materials in terms of their maximum compressible thickness. Tests were also performed with different resin polymers used as binding mixture with ceramics powder. Chemical analyses and investigations through scanning electronic microscopic (SEM), X-ray and real tests for the synthesis of diamond were also performed. The results showed that local Brazilian calcite can be successfully used in the manufacture of HPHT gaskets.

Jan 1, 2006

By R. Romano

Some topics, which difficult the effective use of RMR for dam foundations, are reviewed and a new geomechanics classification system, DMR (Dam Mass Rating), is proposed -as an adaptation of RMR- giving guidelines for several practical aspects in dam engineering and appraisal of dam foundation. On revise quelques problems qui ont fait difficile l’application du RMR pour les fondations des barrages. On propose un nouveau classification système, DMR (Dam Mass Rating)-comme un désarroi du RMR-qui donne recommendations pour quelques problèmes pratiques dans le projet et construction des barrages, et de ses fondations. Es werden einige die praxisgerechte Nutzung des RMR (Rock mass Rating) erschwerende Themen betrachtet und ein neues Geomechanisches Einteilungssystem, das DMR (Dam Mass Rating), eine Anpassung des RMR, vorgeschlagen. Daraus resultieren neue Richtlinien für verschiedene praktische Aspekte beim Dammbau und bei der Beurteilung von Dammunterbauten

Jan 1, 2003

By Ralph E. Burnham, Jeff Taylor, Jonson Montgomery, J. Kelly Ratliff, Rennie Montgomery, Martin Brashear

Top priorities for all blasting companies and individual blasters are risk management, safety of company personnel and the general public, regulatory compliance, and liability protection. On a daily basis, hundreds of shots are detonated by well-trained, skilled, and experienced blasters without incident. Unfortunately, accidents inevitably occur, which is why blasting is considered an “ultra hazardous” or “inherently dangerous” activity from a legal perspective. Despite countless regulations, recent advances in technology, improved training, ongoing research, and improved communication in the industry, mistakes and the resulting incidents continue to occur during blasting operations. These result in dangerous or deadly flyrock, site security lapses, increased complaints, blast damage claims, and lawsuits, which lead to increased insurance costs and other financial tolls for blasting companies. In life, lessons learned the hard way are rarely forgotten. The same is true in blasting operations. Blasting missteps and the resulting events are often the best catalysts for improving risk management and thereby reducing accidents, liability, and financial tolls. This paper provides a summary of two incidents, one safety and the other liability related, and the errors that resulted in a fatality in one case and a multi property lawsuit in the other. The two incidents provide examples that serve as a case study for lessons learned the hard way in blasting operations and offer guidance for the considerations that blasters and blasting companies should incorporate into daily operating procedures.

Jan 1, 2018

By L. H. DeWald

During the examination of various commercial brands of copper wire bars, which had exhibited different degrees of adaptability for being drawn into fine gages of wire by the present-day high speed machine, it was found that each brand had a more or less characteristic crystal macrostructure. The extremes of these macrostructures are similar FIG. 1.-EFFECT OF METAL TEMPERATURE IN CASTING ON CRYSTAL MACROSTRUCTURE OF BAR. Reading from left to right, metal temperatures were 1166" C., 1149" C., 1132" C.. 1121" C., 1093" C. to the maximum variation shown in the photomacrographs reproduced in Fig. 1. As the various brands did not differ materially in chemical composition, it was concluded that the differences in structure were the result of variations in casting technique.

Jan 1, 1931

By A. R. Taylor

In recent years, thermodynamic data have been used to a greater degree than ever by the chemical and metallurgical engineer as a means of predicting and controlling chemical reactions. To satisfy the spiraling demand for basic physical data needed for the calculations, the Bureau of Mines is studying the heat capacities of a variety of chemical compounds at high and low temperatures. This paper is one of a series presenting such data. The heat capacities of two alkaline earth compounds, strontium bromide and strontium nitrate, were measured in a temperature range of 60° to 300° K. in an adiabatic calorimeter and at temperatures of 300° to about 1,200° K. in a Bunsen ice calorimeter. The construction and operation of the calorimeters are discussed in other reports.3 4 The heat-capacity data presented in this report were extrapolated to 0° K., and smooth values of heat capacity, entropy, enthalpy function, and free-energy function were calculated and tabulated at even 10-degree intervals. The enthalpy data were fitted with algebraic equations by applying the method of least squares; calculations a£ heat-capacity values, entropy, enthalpy function, and free-energy function were made at even 50-degree intervals. The heat and entropy of fusion of strontium bromide were calculated from the enthalpy measurements.

Jan 1, 1962