Search Documents

A201 aluminium alloy is a high strength casting alloy with a nominal composition of Al-4.6Cu-0.3Mg-0.6Ag. It is strengthened by the O(Al2Cu) phase and the ??(Al2Cu) phase during heat treatment. Further strengthening of this alloy system can be obtained through the addition of transition elements, but care must be taken as other elements might have adverse effects on the mechanical properties. The objective of this study is to determine the influence of Mn on the tensile properties of rheo-processed Al-Cu-Mg-Ag alloy A201. ThermoCalc software was used to predict the different phases that can be expected in the alloys, and scanning electron microscopy(SEM) with energy dispersive spectroscopy (EDS) was used to investigate the actual phases that formed. The influence of these phases on tensile properties is quantified. SEM and ThermoCalc revealed that there is an increased amount of the Al20Cu2Mn3 with increasing Mn. The tensile properties showed that high amounts of Mn do have adverse effects on the tensile properties of alloy A201, especially the ductility. Keywords Semi-solid metal (SSM) forming, alloy A201, intermetallics, Al20Cu2Mn3

Jan 1, 2011

By J. Searra, M. Aboagye

"For new mining projects or for medium- to long-term areas of existing mines, drilling data is invariably on a relatively large grid. Direct estimates for selective mining units (SMUs), and also for much larger block units, will then be smoothed due to the information effects and the high error variance.The difficulty is that ultimately, during mining, selection will be done on the basis of SMUs on the final close-spaced data grid (grade control), which will then be available, i.e. the actual selection will be more efficient, with fewer misclassifications. However, this ultimate mining position is unknown at the project feasibility stage and therefore has to be estimated. This estimation is required because any cash flow calculations made on the basis of the smoothed estimates will obviously misrepresent the overall economic value of the project, i.e. the average grade of blocks above cut-off will be underestimated and the tonnage overestimated for cut-off grades below the average grade of the orebody. Similarly, unsmoothed estimates will be conditionally biased and will give even worse results, particularly in local areas of short- and medium-term planning or mining.This paper presents a case study of indirect post-processing and proportional modelling of recoverable resources designed for mediumand long-term mine planning at the Gold Fields’ Tarkwa Mine in Ghana. The case study compares long-term indirect recoverable mineral resource estimates based on typical widely spaced feasibility data to the corresponding production grade control model as well as the mine production. The paper also proposes certain critical regression slope and kriging efficiency control limits to avoid inefficient medium- to longterm recoverable estimates, and highlights the danger of accepting block estimates that have a slope of regression less than 0.5."

Jan 1, 2015

By Murali M. Gadde

Perimeter mining is a special form of very productive partial extraction method practiced at some mines in the United States. In the Illinois Basin mines where all major coal seams have weak underclay in the immediate floor, experience shows that any long-term ground control issues will arise due to floor failures rather than instability of the coal pillar itself. While there is a significant amount of work done on floor stability associated with regular pillars, no work has been done so far on the stability of perimeter pillars. This paper reports the results of a comprehensive study that was conducted for the first time on floor stability during perimeter mining in the Illinois Basin mines. A special plate template, which mimicked a common perimeter pillar configuration was created to conduct in-situ bearing capacity tests at five mines in three states of the Basin. Additionally, because of the complex shape of pillars created in perimeter mining that defies any closed-form solution, floor bearing capacity was studied using three-dimensional nonlinear numerical modeling. Based on these in-situ and numerical studies, some guidelines are provided for perimeter pillar stability analysis.

Jan 1, 2009

By Marcus A. Wiley, Gregory Abramov

Borehole mining (BHM) is a remotely operated method of extracting rock material through boreholes by high-pressure water jets. Figure 1 illustrates a BHM tool and fluids circulation. The tool consists of at least two pipes, one for pumping down high-pressure water, the second for delivering slurry to the surface. This article reviews the BHM process. It discusses current and new applications for borehole mining and help the readers determine if BHM is applicable in their situations. Previous articles in ME about BHM explained either a particular project (ME, April 2001, pp. 33-36) or a newest patent in this area (ME, March 1991, pp. 313-318). However, neither one provided an overview on the modern BHM technology.

Jan 1, 2004

THE choice of a pumping plant for the drainage of a mine is a matter of such importance that it is obvious that in a short paper it is impossible to go fully into the reasons governing the adoption of any particular type. The author, therefore, proposes to briefly discuss the methods.in vogue, and, as far as possible, to point out the advantages and disadvantages of the numerous systems. The probiem is of extreme importance to the mining engineer, and it appears that in the past sufficient thought has not been given to this branch, as shown by the numerous failures which are encountered.When water is met with in large quantities, the development of the mine depends upon the pumping plant to such a great extent that the most careful consideration should be given before deciding on any particular scheme for drainage. The pumpingplant in a mine should be looked. upon in the light of an insurance policy, and should be treated as such, care being taken that the premium is as low as possibl~, and to ensure this it is necessary that the most efficient plant be secured. Local conditions play such an important part ill the design of a plant that no hard and fast rules can be laid down. When the amount of water to be handled is small, and there is no possibility of any increase...

Jan 1, 1912

In the course of work being carried out in the Lubricants and Bearings Section of the Council lor Scientific and Industrial Research on the production of copper4ead 'bearings for 'use in aircraft, it has been found necessary to develop special metallographic methods. For proper control of the production of steel-backed copper-lead bearings it is necessary to adhere to rigidly controlled conditions, and it is essential that a method of examination be adopted which will readily detect actual defects or any variations in quality. Some defects can be observed with the naked eye, whilst others are detected by radiographic examination. This latter method is invaluable as a rapid, reliable test in the production of aircraft bearings, but it is necessary to observe the structure of the alloys under the microscope, both to be able to interpret the radiograph correctly and to determine what has occurred to the metal during and after solidification. The use of a sound metallographic technique is'particularly important in developmental work and research connected with these bearings.Polishing TechniqueCopper and lead are practically immiscible in the solid state, but whilst they are miscible only in certain limited proportions in the liquid state; consequently "alloys" of copper and lead consist of a mixture of the constituent metals. The metallographic difficulties are obvious. Copper is a relatively tough metal, although it readily scratches, whilst lead is extremely soft and easily deformed. It wouId be expected if any normal polishing technique were applied that the lead would be readily torn out of the surface being prepared, and, in addition, that the lead would tarnish very easily.Grange(2) has described a method by which these difficulties can be overcome. The method involves an etch-polish procedure using "chrome regia" as an etchant for the copper. The chrome regia was a solution of chromium trioxide and hydrochloric acid in water. This type of etchant has been adopted, but it was found necessary to make certain changes.The method now adopted in this laboratory is as follows: The specimen (which is usually mounted in bakelite) is wet ground in a series of successively finer Hydro-Durexsil emery papers down to 60.0· grit paper.The specimen is then etched in the chrome regis, etchant (the composition of this etchant will pe discussed later) for approximately five seconds.Most efficient etching is obtained by swabbing the surface of the specimen...

Jan 1, 1944

Size Separation Pretreatment and Alumina Recovery from Bayer Red Mud

Sep 13, 2010

It is a great honour to be privileged to address The Institute for a second time as President and I appreciate it more than I can say. Eight years ago in Hobart I tried to cover the development of the mineral industry in Tasmania. That was a general subject. Tonight I want to be more specific - I propose to talk to you about rutile.The choice of subject for a Presidential Address is never easy. One is addressing an informed audience and the best one can do is to try to crystallize a particular subject and to present it in a form that willbe of interest to those who listen.I looked carefully at the addresses given by our Presidents over the past seven or eight years. The titles are impressive, the content excellent, and the length, as published, much greater than I had hoped.It is therefore with some trepidation that I have chosen as a subject one only of the three crystal forms of titanium dioxide. This subject is not as limited as may at first appear.There are two aspects with which I can deal - the mineral itself, which has become familiar as the major product of the East Coast beach sand operations, and the lesser-known "synthetic" product, which is the major pigment in almost all the white paints in common use today, and in cosmetics and white-walled tyres and toothpaste, and even the better types of fine papers. The synthetic form of rutile is' the "whitest"of white pigments.

Jan 1, 1966

By Gordon M. Matheson, Douglas A. Anderson, David K. Miller

"Traditionally, analysis of vibrations from blasting has been focused on peak particle velocity fordetermining the likelihood of both annoyance and damage. The US Bureau of Mines, in RI 8507,indicated the importance of frequency in vibration. Methods of controlling the vibration by reducingthe vibration concentrated in certain frequency bands using delays have been successful over the past decade."

Jan 1, 1997

By Paul J. Sylvester, Yeonuk Choi, Mike Nelson, Louis J. Cabri, Mike Tubrett

"The development and characterization of sulphide standards containing as many as seven precious metals has increased the efficiency and comprehensiveness of micro-analyses for deportment studies using laser ablation microprobe inductively coupled plasma mass spectrometry (LAM-ICPMS). Because trace precious metals occurring in solid solution or as sub-micron inclusions in sulphides, arsenides, and sulpharsenides are often heterogeneously distributed, a significantly large number of analyses are required. Using well-prepared samples it is possible for up to 120 analyses per day, far more than by other comparable methods. Examples will be discussed from projects focused on the deportment of Au and the platinum group elements (PGE).INTRODUCTIONBecause gold and the platinum-group elements (PGE) occur as both discrete minerals and in trace quantities in a variety of minerals (mostly sulphide, arsenide, and sulpharsenide minerals), specialized trace analytical methods were developed and applied to determine the deportment of precious metals in ore deposits, requiring sensitivities ranging originally from about hundreds to presently tens of ppb for individual precious metal or less.In mineralogical studies, micro-analytical techniques such as the electron microprobe were first applied to obtain analyses for major elements in about 1959-60, but as the instrumentation improved early attempts for PGE in potential carrier minerals indicated that reasonable levels of detection (LOD) were of the order of 300-400 ppm, depending on analytical conditions, X-ray spectral lines, and mineral matrix (e.g., Cabri and Laflamme, 1976). Eventually, the lowest detection levels by electron probe micro-analyses (EPMA) obtained for some PGE were of the order of 10s of ppm using high accelerating voltage and current for extended measuring time on peak and background (Gervilla, Cabri, Kojonen, Oberthür, Weiser, Johanson, Sie, Campbell, Teesdale and Laflamme, 2004)."

Jan 1, 2010

The Annual General Meeting of the South African Institute of Mining and Metallurgy was held in Kelvin House, Johannesburg, on Wednesday, 27th August, 1980. Mr D. A. Viljoen (President) was in the chair and declared the meeting open at 4.05 p.m. Obituaries President: It is my sad duty to announce the death of the following members of the Institute: T. C. A. Meyer (Past President, 1941 to 1942); E. G. Harding, T. A. Stannard, C. T. Hardy, W. C. Jackson, J. S. Sinton, G. H. Duggan, H. H. A. Muller (Life Fellows); W. M. Frames, K. Gebhard, W. M. Walker, S. L. S. Swart, N. W. Stansmore, H. E. Allen, B. W. F. Towne, R. A. Wilson, D. Waterman (Fellows), R. M. Peterson (Life Member); D. L. Gibbs (Member); B. M. Williams (Asso¬ciate Member); D. B. T. Cresswell, P. G. Guernier (Associates). As a mark of respect to the memory of the deceased, and in sympathy with the bereaved, please rise and observe a few moments of silence. Notules President: Kan ons die notules van die Algemene Jaar¬vergadering, wat op 22 Augustus 1979 gehou was en in die September uitgawe van ons Joernaal gepubliseer is, bevestig? Bevestig.

Jan 1, 1980

The Calypso geothermal field, mapped by the R V Sonne (cruise SO-135) in 1998, includes four main sites, the Northern Vent Area (centred on 37¦ 36.7'S, 177¦ 06.2'E, area 1.5 km2), Central Vent Area (37¦ 39.4'S, 177¦ 05.2'E, 1 km2), Southern Vent Area (37¦ 41.7'S, 177¦ 06.0'E, 1 km2) and Mercury Vent Area (37¦ 41.3'S, 177¦ 07.3 'E, 0.5 km2). Hydrothermal activity at the vent sites is controlled by minor, sub-parallel NE-trending normal faults. Gas bubble trails (C02) and shimmering hot water vent from fractures and joints between large blocks of silicified volcaniclastics and in depressions in the sediments at the base of these outcrops. Measured maximum vent temperatures are between 180¦C and 201¦C. Venting fluids are at, or just below, boiling for water depths of 200 m. Rock samples recovered by dredge from the sites include massive anhydrite, clay-altered pumiceous ash, silicified volcaniclastic sediments and volcaniclastic breccias cemented by sulphur. Clay-altered samples, dominated by randomly interstratified illite-smectite and accessory chlorite, indicate formation environments of 70¦C to 90 ¦C. Native sulphur is abundant throughout the samples. Fine-grained (<1 mm) disseminated pyrite and vein pyrite occurs in the clay-altered pumiceous volcaniclastics and argillites. In the Southern and Mercury Vent Areas, fine-grained orpiment, realgar and cinnabar have deposited in the sandy matrix of volcaniclastic breccias. Amongst the cinnabar, small (<2 mm) beads of native Hg formed on the surface of several rocks following their recovery. These samples also contained abundant light hydrocarbons, which coat the rocks with an oily sheen.

Jan 1, 1999

By Allan E. Martin, George Glocker, C. E. Wood

"INTRODUCTION As part of a comprehensive investigation of the mechanism of defurization of iron and steel by slags, the Blast Furnace Studies Section, Metallurgical Division, Bureau of Mines, in cooperation with the Institute of Technology, University of Minnesota, has made a study of the forms in which sulfur occurs in blast-furnace slag. This report presents data on the three sulfides most important in iron smelting, namely, ferrous sulfide, manganous sulfide, and calcium sulfide. The tendency of these sulfides to form colloids in the molten slag was determined by an examination of quenched samples with an ultramicroscope.Vogt/ conducted experiments on sulfide silicate melts and examined synthetic blast-furnace slags in a partly crystallized condition. His conclusions were that FeS, CaS, and MnS, or isomorphous compounds, such as (FexCay)S and (MnxCaa)S, were precipitated from the melt, depending on the composition of the slag. In all specimens sulfides were visible and were spherical.Coloration of glass by sulfur also provides indirect information on the nature of sulfur in blast-furnace slags./ There seems to be a general agreement at present among the workers in the field of colored glasses that ferrous sulfide is a strong color producer. Colors that have been attributed to this compound include yellow, orange, brown, blue, and black. Apparently the ferrous sulfide is considered to be dissolved in these glasses. There is no indication that any of them have been examined for a colloidal phase.Lorenz 7/ investigated a single manganese slag in the glassy state and observed a Tyndall beam in an ultramicroscope. His conclusion was that either a manganese compound had precipitated in a finely divided condition or that metallic manganese had volatilized and penetrated into the slag as a vapor and thus formed colloidal particles."

Feb 1, 1941

By Bruno Gemmi

The objective of the ? 200 million ($280 million) project Parma Railways Station-Urban Transformation was the reconnection of the North and South parts of the town by constructing an 80 m (250 ft) wide sunken artery passing under the four double railway tracks of the station without any impact on train traffic. The site of the project, adjacent to the Parma River, presented water seepage problems at any excavation depth. The use of conventional large diameter bored pile machinery was not allowed by the Railway Authority because equipment dimension and construction phases do not comply with train traffic safety regulations. Foundations for the bypass were thus constructed by minipiles nested into jet-grouted soil using machinery operating within the existing head room and at a safe distance from the tracks. Jet-grouting treatment reached depths of 25 to 28 m (80 to 90 ft) from tracks? grade and embedded minipile-heads were terminated at 2 to 3 m (6.6 to 10 ft) below grade. Load tests on minipiles were pushed to failure. Failure occurred at a 240 t (265 t) load without breakage of the bond between the jet grouted soil and the minipiles. A 0.93 MPa (135 psi) shear resistance ??? between minipile steel casing and the jet grouted soil was measured prior to the failure of the steel casings. Overall measured foundation settlements were well within expected values and were considered insignificant.

Jan 1, 2011

By John D. Sullivan, Alfred P. Towne

"In copper percolation-leaching plants the ore is usually crushed to a maximum size of about three-eighths inch. Ordinarily an ore is crushed as finely as feasible since the rate of extraction of copper is increased with decreasing size of particles owing to the greater surface exposed and. the shorter path required for solutions to come into contact with the minerals to be dissolved. However, greater degree of crushing also increases the amount of fines. When ores are charged into leaching vats the coarse and fine material tend to segregate, resulting in channeling of solutions and leaving the areas where fines predominate only partly leached. An improvement in the method of charging the ore into vats that would minimize the deleterious effects of the segregations of fines would increase the percentage extraction of copper.The Inspiration Consolidated Copper Co.4 recently installed classifiers to remove the primary slimes from the ore, before charging it into the leaching vats. This necessitates a separate agitation treatment for the slimes.Recent publications5 of the bureau have shown the advantages of agglomeration followed by trickle leaching to extract copper from concentrator tailings. It was shown that when equal parts of ore crushed to about 1/4-inch size and concentrator tailings were agglomerated with approximately 10 per cent of moisture, either in the form of water or leaching solution, and the mass was charred into a leaching vat the ore could be treated successfully by open-drainage trickle leaching. Even with 30 or 35 per cent of minus 200-mesh material present the ore could be leached, if it was not flooded with solution.The results obtained in agglomerating ores and slimes suggested the possible advantages to be gained by wetting the crushed ore for standard percolation-leaching plants before charging it into the vats. Wetting the ore whould make the fine material and slime cohere to the larger pieces of ore thus tend to prevent segregation when the ore is charged into the vats. The bureau, at its southwest Experiment Station and in cooperation with the Department of Mining and University of Arizona, Tucson Ariz., therefore made a study to work: out A way in which slimes could be handled in percolation leaching. The study showed that the method of charging ore into the leaching vats governed the distribution the fines and consequently the rate extraction of copper. The results of the study reported in this paper."

Feb 1, 1931

Models are used in engineering to reproduce reality as faithfully as possible so that the expected response of a system for given actions or inputs can be determined. In the field of rock engineering, both empirically based and numerical models are widely used to determine the likely response of the rock surrounding excavations. Many of the empirical models are developed from statistical analysis of case histories or from direct observation; however, empirical models are limited because they should be used only within the range of conditions of the observational database. Synergy exists between empirical and numerical models, because empirical models can be used to calibrate and validate numerical models. The empirical approach can benefit from the capability of numerical models to investigate specific mechanisms, which would not be possible using observations alone. Two cases are presented in which the synergy between empirical and numerical models is demonstrated. The first case examines the analysis of discontinuity effects on the strength of slender pillars in limestone mines, and the second case evaluates the effects of stress orientation on coal mine entry stability. It is concluded that numerical model calibration and verification comprises an important first stage in the successful application of models in rock engineering design. Application of numerical models allows mechanisms and interactions of various parameters to be analysed, greatly improving the understanding of the system. The improved understanding can be used to extend the application of empirical design methods, resulting in improved safety and efficiency of rock engineering designs.

Jan 1, 2014

By Graeme McWhirter

This paper discusses the Installation of a Vibwall for the Cardiff Bay Barrage Project Wales, UK, by Kvaerner Cementation Foundations. Only the second use of the technique in the UK the wall was successfully placed to a depth in excess of 20 metres, in unique and challenging conditions. The installation of the Vibwall was a technical success, but not a financial one. The use of the technique was at its "limits" and this paper recommends some of the controls essential in the carrying out of such work in the future.

Jan 1, 2000

By Homer J. Ballinger

"SUMMARYDuring December 1945, the Bureau of Mines began churn drilling the Winchester zinc deposit, 11 miles south of Joplin in Newton County, Mo. The deposit lies in a virgin area northwest of the Seneca fault. It is one of several deposits partly proven by drilling but never developed.Logs of 28 privately drilled holes had indicated a substantial tonnage without delimiting the deposit. It appeared that additional drilling might increase this reserve sufficiently to justify mining. A, total of 6,33 feet of churn drilling was completed in 17 holes drilled by the Bureau of Mines. Twelve of the holes penetrated minable ore extending the length of the known deposit and materially increasing its estimated tonnage.INTRODUCTIONDuring May 1943, the Winchester property in Newton County, was visited by an engineer 3/ of the Bureau of Mines, accompanied by Dr. A. N. Winchester, owner, and Charles Keith, lessee of the property. At the request and with the assistance of these gentlemen, examination of the property was undertaken. Logs of 28 churn-drill holes were collected, hole locations were surveyed, and available historical data were obtained. It was concluded that although existing drill holes indicated considerable reserves, additional drilling might increase the tonnage substantially. In addition, it was believed that better knowledge of this ore deposit could be obtained by drilling further, and this knowledge could, in turn, be applied to other less proven deposits in the same field."

Jul 1, 1947

The problem of separating the constituents of a mixed gas has assumed increasing importance to chemical technology during the last several decades. Metallurgical practice, dealing mostly with the application of gases as fuel, such as for the oxidation or reduction of ores, has not often confronted an important need for such separations. If theory occasionally has indicated advantages in the use of purified or separated gases, as for example the "dry" blast for the iron furnace or oxygen-enriched blast for a variety of smelting operations, the economics of the proposals has not often been satisfactory. It has seemed evident that the practice of the chemical plant was too expensive with regard to installation or material costs, or both, for the needs of the basic smelting industries and indeed was applicable commercially to metallurgical purposes only when the metals in question were especially valuable or pure. This bulletin deals with a new mechanical means of attacking the problem of separation. Although it is improbable that any one type of separation could hope to find universal application, the method described is to be regarded as an alternative to conventional means that has attractive possibilities in certain instances. It extends the number of methods previously available by one that has not before been applied commercially and that utilizes a well-known property of gases that never has received effective technologic attention.

Jan 1, 1940

By D Craw, I M. Turnbull, R J. Norris, N Mortimer

The Otago Schist is being subdivided on a regional scale into structurally, metamorphically and lithologically distinct blocks. Differences between blocks are subtle, and difficult to map in the field. Boundaries are late-metamorphic or immediately post-metamorphic in origin, and are different from later brittle faults which disrupt the schist. Mapping of late-post-metamorphic structural discontinuities has direct application for basic grassroots exploration in the Otago Schist. The mineralised (and currently mined) Hyde-Macraes Shear Zone forms a regional scale boundary between a block dominated by politic schist and a block with massive psammitic schist, pelitic schist, and minor greenschist and chert. The HMSZ forms a metamorphic discontinuity, with garnet and biotite in the underlying schist, and neither index minerals apparent in the overlying schist. The HMSZ is also a structural boundary between domains with differing lineation orientations. The HMSZ can not yet be traced along strike to the northwest to the Rock and Pillar Range, where the only major discontinuities recognised are the Caples-Torlesse boundary and a normal fault separating low grade from high grade schist. Structural and lithological discontinuities in the Dunstan Range break the range up into distinct structural blocks, two of which are separated by the gold-mineralised Rise and Shine Shear Zone.

Jan 1, 1999