Search Documents

The process of pile driving disturbs the soil around the pile. The nature and magnitude of disturbance depends upon 1) the pile size, and 2) the nature of soil. Therefore, the prediction of a single pile behavior based on soil properties of undisturbed soil samples may not match its performance. Under lateral loads, the pile may loose contact with the soil near the ground surface especially in clays. The soil pile interactions are influenced the most by pile behavior in this zone. This situation further affects the tally of prediction and performance. Piles are used in groups. The zones of overlapping stress from one pile to the other both around the pile and below their tip particularly in soft soils, contribute to group effects. Empirical solutions have been developed for prediction of the pile group behavior. The group action is more involved under vibrations. Several cases of single piles and pile groups under static and dynamic loads from published records have been analysed. It has been shown that single pile test is the best source of information on the soil-pile-soil interaction effects.

Jan 1, 1989

By Merete Tangstad, Kai Tang

The primary aim of the present investigation is to develop a model which permits to calculate/predict the viscosities of ferromanganese slags, typically focus on the MnO-SiO2-Al2O3-CaO-MgO-FeO multicomponent system. The present viscosity model emphasizes the ability of prediction, i.e. using the binary parameters to extrapolate the viscosities in ternary and higher order systems. To this end, a physical sound model is essential. Temperature dependence of viscosity is described by the Eyring?s formalism. The well-known cell model is used to define the SiO44- tetrahedra in the silicate melts. Composition dependence is expressed in term of viscous activation energy, which is characterized by the binary structural units. The viscosities in ternary and higher order systems are hence predicted using the binary activation parameters. The model has been used to calculate the viscosities in the whole liquid composition range of ferromanganese slag.

Jan 1, 2007

By S. N. Lekakh

Phosphorous segregated at grain boundaries during solidification and heat treatment dramatically decreases low temperature toughness of precipitation hardened Fe-Mn-Al-C austenitic steel. A thermodynamic analysis was performed to evaluate the possibility of decreasing P and subsequent segregation by Ca- and Ce-additives in the melt. It was shown that the predicted probability of forming a P containing compounds depends on melt composition and treatment sequence. Experimental heats were performed and several micro- and macro-structural effects of Ca- and Ce-additives were recognized by using an automated inclusion analysis technique.

Jan 1, 2010

By E. R. Spencer

National Institute for Occupational Safety and Health (NIOSH) researchers conducted an investigation to quantify sound levels and to determine the amount of sound reduction provided by engineering noise controls installed in a talc processing plant. Baseline sound level and sound intensity measurements were performed at the plant and the measurement locations were recorded for comparison to post-control measurements. Follow-up measurements were then made at the same locations after the initial noise controls were installed. The plant subsequently decided to implement additional noise controls and the researchers returned to conduct measurements for a final analysis of all noise controls. The most significant results showed a sound level reduction in the main mill area from a range of 93-104 dB(A) down to 90-94 dB(A), and a total sound power level reduction of 21 dB(A) for air classifying mill 3.

Jan 1, 2008

By J. B. Gayle

Commercial flotation plants operate on a continuous basis that is not simulated closely by the batch testing methods widely used in Bureau of Mines laboratory studies of flotation, Batch methods indicate whether a particular separation is possible but provide little or no information about the rates at which such separations can be effected in continuous operation, Therefore, laboratory equipment suitable for testing on a continuous basis was assembled for an investigation of a number of the operating variables that influence the flotation of coal. The results of these tests lead to the following conclusions: 1. Flotation recoveries were markedly influenced by variations in the percent solids in the feed, However, the relation between these variables is complex and depends on the particular coal and operating conditions used. Flotation rates generally increased with increased cell concentrations.

Jan 1, 1962

By A. Fuerst

The recent seismic events have shown that earthquakes have an immense destructive power. Chile was hit in February 2010 with a seismic intensity of 8.8 on the Richter scale, and had loss of about 700 killed persons, while Haiti was hit in January 2010 with 7.0 killing about 220?000 people. The event in Haiti showed that the seismic events can lead to a disaster if no preventive measures are taken. On the other side, the seismic event in Chile has hit a well-prepared country with moderate consequences. The earthquake with 6.6 Richter in Japan in March 2011, have further shown how severe the consequences can be if critical equipment is involved. Fortunately, the equipment in a mine has not the potential hazard as a nuclear power plant. Anyway, we are diligent and it is obvious that the seismic risk may lead to a real disaster even if the probability is small. The GMD is an important component in the grinding circuit of a mine. This paper maps out earthquake-prone areas including expected earthquake magnitude calculated according to relevant standards, focusing mainly on the building code IBC 2009. An overview is provided on how this standard is applied to mining equipment to minimize damage and aid large mills in operation to successfully withstand seismic effects. The differences in stresses and forces on the GMD and foundation are shown based on a turning and stopped mill simulation during an earthquake. The results demonstrate the need to maintain active and operating earthquake detection systems. Aside from detecting an earthquake?s magnitude, the sensor information can also be used to reduce the harmful effects that an earthquake has on mining equipment. As follows the earthquake requirements are defined. The last part of this paper explains how to fullfill these requirements.

Jan 1, 2012

By D Barclay, S Mercer, S Wright

Mine water management is often an afterthought in mine planning processes and can introduce significant risks to projects when studied as a stand alone component at a later stage in the mine design. Incorporation of a mine dewatering and pore pressure dissipation strategy in the early stages of mine planning is imperative in order to minimise constraints on the production schedule, to match designed pit slopes and maximise project value for an open cut mine option such as Olympic Dam. A risk-based mine planning approach was adopted during the project selection phase study whereby water management was introduced into mine planning, scheduling and the development of an operational strategy. Hydrological and hydrogeological studies and outputs were successfully integrated into the various iterations of the mine planning cycle during early selection phase to manage the potential water management risks associated with pit slope depressurisation and access to dry working conditions during rapid advancement of mining phases.An extensive network of vibrating wire piezometer sets and long-term depressurisation testing characterised aquifer conditions and demonstrated that hydraulic connectivity exists within the geological profile due to the presence of structures and resource drill holes which enhance vertical connectivity. This connectivity, along with underdrainage from mining activities contributes up to 100 m of depressurisation in low permeability units.A pit dewatering strategy incorporates the mine planning schedules and accounts for operational constraints as to the location and development of the dewatering wells, storages and pipelines. Numerical modelling generated a range of likely pit inflows and dewatering requirements with the average initial dewatering discharge likely to be 150 L/s and reduce quickly to 50 L/s after five years, depending on the premine schedule.Coupled hydrogeological and geotechnical assessments were also carried out as part of the mine planning cycle and indicate that successful dewatering will go a long way to reduce the pore pressures within key geotechnical units during the rapid mining phase where around 300 m of cover sequence is stripped in five years. However, the residual storage in the primary aquifer and the residual pore pressure in underlying low permeability units will need to be dissipated (in-pit horizontal holes) as the pit floor advances. Pit slope design angles are sensitive to depressurisation and dewatering and up to 70 per cent depressurisation of key geotechnical rock units are required. Whilst an accelerated program of aquifer dewatering supported by lithostatic unloading should drive rapid depressurisation in the lower permeability units, intervention is anticipated in key geotechnical units such as the Tregolana Shale and volcaniclastics. The extent of induced drainage will ultimately depend in part upon the mining rate and geotechnical stability requirements. Practical operability testing addressed the potential for operational constraints to mine depressurisation activities such as congestion and mining schedule development within the pit and identified that depressurisation drilling can be achieved even with reduced access availability. Mine operations and planning groups established design criteria and considered the likely inoperable periods following rainfall events of seven to 14 days to manage the base surge and minimise impact on production. In-pit surface water management options to minimise operational disruptions during and after significant rainfall events were estimated used a stochastic approach.

Jan 1, 2009

By R. E. Moore

Refractories are unique ceramic materials, which are used in large quantities in steel making furnaces, metal smelting vessels, and glass melting tanks. They are required to possess high thermal shock properties and good slag corrosion resistance as well as creep resistance at high temperatures. Therefore, they are made from very refractory minerals such as lime, periclase, corundum, spinel, and zirconia. Slags are vitreous materials produced as a residue in steel refining processes. They cover a wide range of compositions and may contain pure oxides, silicates, and sulfides as well as fluoride phases depending on the melting and smelting processes. These minerals exhibit spectacular cathodoluminescence color under electron bombardment; therefore, cathodoluminescence (CL) microscopy is found to be a superior technique for the characterization of refractory corrosion by slags. Examples included in this study are (1) reaction of fluorine containing mold slags with ZrO2-C nozzle refractories promoting crystallization of the Cuspidine, Ca4Si2O7(F,OH)2, (2) corrosion of fusion cast refractories in TV panel glassmaking furnaces and formation of glass defects, and (3) reaction of spinel based castable refractories with copper smelting slags.

Jan 1, 2001

By J. Allan Tice

In the past fifteen to twenty years, the use of drilled piers to support high capacities in coastal plain deposits has become more and more common. With improved construction techniques and better understanding of pier behavior, drilled shafts with capacities of 200 to 500 tons are not unusual. The purpose of this presentation is to review several drilled pier installations from North Carolina to north-east Florida as a means of illustrating the different types of design concepts and installation techniques which are presently being used. ACKNOWLEDGEMENTS The information in this presentation was obtained from work performed by many individuals and companies. The section on limestone socket caissons in South Carolina is an abridged version of a paper prepared by Rob Smith and Neil Gilbert of Law Engineering's Charlotte, North Carolina office, and is used with permission. The section on pier installation in northeast Florida is an abridged version of a paper prepared by Kirk Mcintosh, Tom McDaniel, and Randy Knott of Law Engineering's Jacksonville, Florida office, reprinted here with permission. Additional data discussed in this presentation has been obtained from Farr Foundation Company, McKinney Drilling Company, and Peterson Drilling Company.

Jan 1, 1988

By Lawrence M. Gochioco

One of the best kept technology secrets in U.S coalmining history involved a robust coal geophysics program used by a local coal company to detect and map various geologic anomalies and man-made structures ahead of mining for nearly 15 years. Several original mine plans were changed as a result of findings from two-dimensional (2D) and three-dimensional (3D) seismic data. They indicated the presence of geologic anomalies in reserve areas that could adversely impact future mine development and longwall production. By combining the surface seismic and exploratory drilling methods, the coal company learned how to properly leverage its risk by gathering a lot of useful subsurface information before making major commitments.

Jan 1, 2005

After a snap-shot survey of water quality of streams draining various coal measures carried out in 2000 - 2001, West Coast Regional Council expanded its monitoring programme to better establish the condition of streams draining coal mining areas and to characterise the variability of water quality with respect to stream flow. Samples were collected for water quality indicators such as pH, sulphate, turbidity, conductivity, temperature and dissolved oxygen as well as macro-invertebrates, fish and assessments of stream habitat. Water quality sampling was carried out at 27 sites on 21 streams located from Page Stream near Seddonville in the north, to Seven Mile Creek near Dunollie in the South, and to Garvey Creek east of Reefton. There was relatively low variability of pH, conductivity and sulphate concentrations at most of the sites sampled. Conductivity and sulphate concentrations reduced with increasing flow and pH generally increased. Significant effects on macro-invertebrate and fish populations were identified at several of the sites where water quality sampling was undertaken. Of the water quality parameters tested, macro-invertebrates were mostly affected by pH. Although not sampled directly (conductivity was used as a surrogate) heavy metal concentration may explain some of the variation in macro-invertebrate communities. Three creeks affected by mine drainage were sampled for fish and no fish were present. Fish appear to be more sensitive to acid rock drainage that invertebrates. Using data from this survey and other studies conducted in the region, the total length of stream that is actually or highly likely to be adversely affected by acid rock drainage was estimated at 125 km. This figure is useful as a gauge as to the magnitude of the issue in this region and for setting of priorities for remediation. However, as it is only an estimate based on limited sampling sites, it should be used with caution.

Jan 1, 2003

By W. G. Pariseau

Reliable stress measurement using hollow inclusion gauges and monitoring stress change using borehole stress meters and borehole deformation gauges in anisotropic rock remains a challenge for the rock mechanics community. In this regard, the complex variable method advanced in 1983 for deducing stress in anisotropic rock is flawed and software is privileged. Fortunately, advances in computer hardware and software now enable fast, reliable reduction of hollow inclusion stress measurement data for determining stress in anisotropic rock. Monitoring stress change in anisotropic rock poses a different challenge but is also subject to numerical analysis. Stress measurement using a hollow inclusion (HI) gauge such as the triaxial Australian HI is done in four steps: 1) drilling a measurement hole, 2) installation of an HI, 3) stress relief of the HI by overcoring, and 4) data reduction. The last step, data reduction, is the focus of this work. The process is well-known in linearly elastic, isotropic rock (Worotniki and Walton 1976, Duncan Fama and Pender 1980). However, in case of linearly elastic, anisotropic rock the requisite technology is not readily available. This situation is somewhat surprising because anisotropy is more often the rule rather than the exception, especially in the neighborhood of ore bodies. Rahn (1984) has pointed out the potential for significant errors with neglect of anisotropy and the adverse consequences for engineering design. Amadei (1984) has also pointed out the potential for errors with neglect of anisotropic rock properties in stress measurement. Worotniki (1993) cites other studies that indicate potential for serious errors when doing measurements in anisotropic rock. In both theoretical cases (isotropy and anisotropy), data reduction is essentially a composite of solutions to boundary value problems in linear elasticity. In the finite element approach, the analysis is a simulation of gauge hole drilling, installation and overcoring. Two important advantages with the finite element approach are a more faithful representation of the conditions of HI stress measurement than approximated in theory and the capability for handling rock whether isotropic, transversely isotropic or fully anisotropic

Mar 2, 2022

By J. E. Sepulveda, R. Morrow

"In full scale mineral grinding operations, the steel balls normally utilized as auxiliary grinding media get to be consumed at different specific rates, as determined by 3 basic mechanisms: abrasion/corrosion (wear), impact ball breakage and impact surface spalling, the latter relating to the removal of rather small pieces of steel coming off the exposed surface of the balls due to repetitive impact with other balls in the charge or the surrounding mill liners. In conventional ball milling applications, the clearly predominant mechanism is gradual wear by abrasion/corrosion. In the case of SAG mills, where the make-up balls may be as large as 6”f diameter, breakage and spalling mechanisms are significant contributors to total ball consumption, although not to the extent of overriding wear mechanisms.Ball wear has been well characterized by the Linear Wear Theory, as presented at the last CMP 2014. Impact breakage has been customarily monitored, at the ball manufacturing site, via Drop Ball Tests (DBT) consisting of repeatedly dropping balls from a standard height and accounting for the number of broken balls and the weight loss (spalling) of the remaining unbroken balls. When properly conducted, DBT’s should provide meaningful indications of the breakage and spalling resistance of large diameter balls. The current publication is focused on the interpretation and projection of DBT results to full industrial scale, taking into account all 3 mechanisms of grinding media consumption in SAG mills.INTRODUCTIONA thorough, quantitative understanding of the independent contribution of all active grinding media consumption mechanisms is of the highest practical relevance, particularly in semiautogenous (SAG) milling operations where ball breakage and spalling can not be ignored or neglected, as it has been normally acceptable for conventional ball milling processes. The high severity impact conditions currently imposed in typical SAG mill environments create serious challenges to the manufacturers and suppliers of large diameter (5”–6”) SAG balls, whose products must be capable of surviving such harsh operational conditions with minimum breakage or spalling."

Jan 1, 2015

By Brian Garrod

Increasing use of pressurized-face tunnel boring machines in North America has produced a similar increase in the application of precast concrete tunnel linings. Where a pressurized TBM is needed, immediate ground support and ground water pressure resistance is also required. A segmental lining installed within the TBM tail shield provides the only available means of providing such a sealed lining. This paper addresses new developments in North America in lining applications and design. For the purposes of this paper, a precast concrete tunnel lining is defined as a tunnel lining constructed using precast concrete segments that are assembled into a lining ring. The lining rings are connected adjacent to each other to form a tunnel lining. Each segment has a sealing gasket around it so that when the lining is completed, it provides a fully waterproof lining system. The ring is erected within the tail shield of the TBM and the annular gap around the ring is filled with grout as the machine moves forward. The ring is not expanded and normally provides the finished lining of the tunnel with no requirement for a second pass lining. The TBM has a series of hydraulic rams that push on the leading edge of the segmental lining to provide the sole system of forward propulsion for the machine. The rings are tapered, being longer on one side than the other. This allows the rings to be installed either on a curve or in a straight line depending on the rotational position of the rings.

Jan 1, 2008

By Amilton Barbosa Botelho Junior

A busca por metais para atender demandas crescentes vem em contracorrente à diminuição dos teores nas reservas. Desta forma, a busca por novas rotas de extração de metais aliada ao desenvolvimento sustentável se faz cada vez mais necessário. O presente trabalho teve por objetivo a recuperação de cobre do lixiviado proveniente de rejeito de níquel laterítico, que contém os seguintes metais: alumínio, cobalto, cromo, cobre, ferro, magnésio, manganês, níquel e zinco. Para isto, utilizou-se o processo de troca-iônica com a resina quelante Lewatit TP 207, uma resina catiônica com grupo funcional iminodiacetato. Estudou-se o tempo de reação e a influência de pH. O tempo de reação foi variado entre 0 e 24 horas e o pH de 0.5 a 2. Não foi estudado maiores valores de pH, pois haveria precipitação do ferro. A reação de adsorção pela resina entrou em equilíbrio em 180min. Em pH 2 teve maior recuperação de cobre, pois havia menor competição entre H+ e os cátions metálicos do licor, onde foi possível recuperar 50% do cobre. Os ensaios ocorreram em batelada com agitação de 200rpm, e as análises foram feitas usando a técnica de fluorescência de raios X por energia dispersiva (EDX).

Oct 30, 2017

By Parker A. J, Muir D. M

Solutions of acetonitrile in water dissolve water soluble copper(I) chloride. Removal of volatile acetonitrile from the resulting solutions, by distillation with low grade steam, precipitates pure copper(I) chloride. This is used to purify a crude copper chloride sublimate from the chlorination of nickel matte but is applicable to other sources of copper(I) chloride. The pure product can be converted to pure copper(I) oxide, copper(II) oxychloride or pure copper metal directly.

Jan 1, 1980

The addition of a thallous salt to the cyanide leach of a calcined pyritic concentrate causes a marked increase in the rate of extraction of gold. This is due probably to the activation of passive gold by the thallous ions. Lead, bismuth, and mercury salts, which should produce a similar effect, fail to do so. It is postulated that this latter result, together with the reprecipitation of silver at low cyanide levels, is due to the presence of soluble sulphide.INTRODUCTIONThe work of Fink and Putnam (1950) showed that the rate of solution of gold in cyanide can be increased by the addition of small amounts of lead, bismuth, mercury, and thallium salts. Mills (1951), during a study of the electrochemistry of gold, with particular reference to cyanidation, was able to show that gold may become passive towards cyanide solution. The addition of lead or thallium salts prevented this passivity, although the action of lead was limited to the pH range 10 to 12. In a recent paper Cathro (1963) confirmed the findings of Mills, and presented results which showed that the addition of thallium to a cyanide leach of a calcine from Lake View and Star mine, Kalgoorlie, increased the rate of extraction of gold appreciably. In, this paper the use of thallium to prevent the gold becoming passive, and hence to decrease leaching time and cyanide consumption, is examined.EXPERIMENTALA series of leaching tests was carried out on a sample of Lake View and Star calcine, comprising calcined pyrite (about 70 per cent.) and siliceous gangue (about 30 per cent.) and containing 165 p.p.m. gold, 45 p.p.m. silver, 0·1...

Jan 1, 1964

By Doris M. Hyde

The economy of Belize continued to show a very slight but still positive growth during 1986. The gross domestic product (GDP) was estimated to have been about $164 million,2 almost the same as those of 1984 and 1985. Foreign investors looked favorably on Belize because it had remained isolated from the sometimes turbulent political and social strife elsewhere in Central America. Reportedly, in late 1986, Guatemala had decided not to pursue its claim to Belizean territory and to give full recognition to that country. Discussions were to be held regarding any matters of mutual concern. New investment possibilities were oriented toward agriculture or manufacturing endeavors. Except for some interest in petroleum exploration, the minerals sector remained limited to the quarrying of construction-related materials.

Jan 1, 1988

By Luciana Pirone de Oliveira

O cobre é encontrado na natureza na forma de óxidos ou sulfetos e sua obtenção na forma metálica é usualmente alcançada através da pirometalurgia e eletrólise. Em ambos os processos há, além do gasto com energia, a geração de grande quantidade de passivos ambientais. Neste contexto a redução via plasma de hidrogênio se apresenta como uma alternativa promissora, pois valores significativos de carga metálica podem ser obtidos em temperaturas inferiores aos processos usuais e tendo como resíduo apenas vapor de água. Neste trabalho procurou-se investigar a influência do fluxo de hidrogênio na eficiência da redução do Cu2O por plasma de hidrogênio em baixa temperatura. Os experimentos foram realizados em reator de plasma pulsado CC nas vazões de 100, 200, 300 e 400 cm3/min, com temperatura constante de 300°C por 1h e pressão de 4Torr. A eficiência da redução foi determinada através de um balanço de massa e as análises dos produtos da redução foram feitas por difração de raios-x (DRX) e microscopia eletrônica de varredura (MEV). Os resultados parciais ratificam a redução a plasma como nova rota para a produção de cobre metálico e demonstram que as variações do fluxo de hidrogênio têm pouca influência na eficiência da redução.

Aug 8, 2018

By Charles F. Seemann

It is with considerable trepidation that I set out to defend "litigation" to Design Professionals (DPs), as a better method of resolving disputes than arbitration, in the light of my personal feeling that an increasing amount of America's productive process is being squandered in litigation. Newer methods of dispute resolution, particularly arbitration, are fashionable, and opponents of these schemes risk being viewed as cynical or self-serving. My quandary is heightened since for some smaller disputes, arbitration seems clearly the better choice. I must concede, for example, that when the cost of dispute resolution--i.e., the cost of the process (such as arbitrators fees, attorneys fees, etc.), plus the cost impact of the non-productivity of involved employees--approximates the amount of the dispute, controlling that cost may be as important as a correct resolution. This principle is particularly true for small disputes arising during the progress of a project; it is probably more cost-effective for all parties to resolve their disputes quickly than permitting the dispute to drag out.

Jan 1, 1988