Search Documents

Stratiform lead-zinc mineralization at the Pegmont prospect occurs as a 4-6 m thick body interbedded within arkose, schist, amphibolite, and pegmatite of the Kuridala Formation in the Eastern Belt of the Lower Proterozoic of northwest Queensland.The overall structure of the body is that of a strongly crumpled east-dipping sheet. In detail it is subjected to complex and irregular deformation.Gossaneous outcrops of the mineralised body are anomalous in Pb-Zn-Ag content and have been traced, discontinuously, over about 36 km2 in a NNE-trending belt.Below the zone of oxidation, which reaches 25-40 m below the surface, the primary sulphides are galena, sphalerite, and pyrite.Drilling on a 2 km2 area near the discovery outcrops indicates fairly uniform grades of lead and zinc.Changes in thickness of the mineralised body are gradual.

Jan 1, 1977

By Misra V. N

Upgrading of a Koolanooka magnetite iron ore sample provided by Kingstream Steel Ltd was investigated using low intensity magnetic separation (LIMS) and reverse flotation. The ore contained 38.6 per cent iron, 37.8 per cent silica, 6.5 per cent magnesia and 0.54 per cent alumina, with the main minerals in the ore being amphibole (42 per cent), magnetite (39 per cent) and quartz (14 per cent). The concentrate obtained after low intensity magnetic separation contained 66.6 per cent iron and 6.34 per cent silica with an iron recovery of 72 per cent. This concentrate was further treated by reverse flotation to increase the iron content and reduce the silica content to meet the requirements for direct reduction iron (DRI) feed grade.

Jan 1, 1999

In the early stages of opening up a mine, when there is some uncertainty as to its future career, necessitating caution in laying out works of a permanent character, the want is often felt of an assay furnace, easily built and easy of transportation, should the" mine " prove to be " no mine." Again, cases occur in which parties buy the right to treat comparatively small heaps of tailings, and then shift their plant to other localities. Under these circumstances it is necessary to restrict the plant to the barest necessaries, to suit, so to speak, the nomadic character of the work.An assay furnace that is really portable, easily transported, erected, taken down, of little weight, always ready for action on short notice, is indeed in these cases a desideratum which has long been wished for. The gasoline furnaces introduced intothe Australian market some time since practically fulfil these conditions; but they have the fatal drawback of being dependent on a constant supply of the liquid fuel, gasoline, which is seldom, if ever, obtainable locally in' any wayback mining township...

Jan 1, 1904

By Alain Blanchier, Gilles Gomez

Neighborhood pressure on quarries has become urgent to deal with quarry managers and operators must apply the most recent technologies and communicate it for long shelf life time exploitation, the quarry in which the work is located in urban or suburban environments needs to take into account blasting rules as well as site environment. The main problems to be addressed are:

Jan 1, 2009

By A. K. Singh, R. Singh, P. K. Mandal

On the basis of in situ study of pillar loading at different sites, an attempt is made in this paper to visualize the development of mining induced stress under varying geo-mining conditions. Field study demonstrated interesting interaction between size of pillar and nature of roof rock mass under the influence of increasing dimension of the excavation. Stiffness of pillars/overburden, extraction ratio and depth cover are observed to be the important parameters for the estimation of mining induced stress over the pillar. These parameters influence, both, the value of ultimate induced stress (vertical) and its range of influence ahead of the face line. Further, it is observed that the change in width/height (w/h) ratio of a pillar has got considerable influence over the nature of mining induced stress over it. Impact of highly dynamic nature of mining induced stress over the natural supports is observed to be the most serious factor for the safety of working under a hard and massive roof rock mass. On the basis of these observations, a conceptual model of interaction between the natural support and overlying strata is discussed in the paper. ZUSAMMENFASSUNG: Aufgrund ist in situ Studium von Säule Beladung an verschiedenen Stellen, ein Versuch in diesem Papier gemacht, die Entwicklung des Bergbaus vostellen sich, Spannung unter Änderung von Geo Bergbau von Bedingungen hat veranlaßt. Feld Studium hat interessante Wechselwirkung zwischen Größe von Säule und Natur von Dach Felsen Masse unter dem Einfluß von Vermehrung Dimension des excavation vorgeführt. Steifheit des Säulen Overburden, Herausziehung Verhältnisses und Tiefe sind beobachtet bedeckt, die wichtigen Parameter für die Schätzung des Bergbaus zu sein, Spannung über der Säule hat veranlaßt. Diese Parameter beeinflussen, beide, der Wert allerletzter veranlaßter Spannung (senkrecht) und sein Bereich des Einflusses voraus von der Gesicht Linie. Weiter ist, es beobachtet, daß die Änderung in Breite Höhe (W H) Verhältnis einer Säule beträchtlichen Einfluß über der Natur des Bergbaus erhalten hat, Spannung hat darüber veranlaßt. Schlag sehr dynamischer Natur des Bergbaus ist Spannung über den natürlichen Stützen beobachtet hat veranlaßt, der ernsteste Faktor für die Sicherheit des Arbeitens unter einer harten und massiven Dach Felsen Masse zu sein. Aufgrund dieser Beobachtungen, ein begriffliches Modell der Wechselwirkung zwischen der natürlichen Stütze und der überlagernde strata ist im Papier diskutiert. RESUME: En se basant sur dans l'étude de situ de chargement de pilier aux sites différents, une tentative est faite dans ce papier pour envisager le développement de creuse la tension persuadée sous varier de conditions de geo creuse. L'étude de champs a démontré l'interaction intéressante entre la taille de pilier et la nature de masse de rocher de toit sous l'influence d'augmenter de dimension de l'excavation. La raideur de piliers overburden, la proportion d'extraction et la couverture de profondeur est observée pour être les paramètres importants pour le jugement de creuse la tension persuadée par-dessus le pilier. Ces paramètres influencent, les deux, la valeur de tension persuadée ultime (vertical) et sa gamme d'influence en avant de la ligne de face. Plus, il est observé que le changement dans la largeur hauteur (le w h) la proportion d'un pilier a reçu l'influence considérable par-dessus la nature de creuse la tension persuadée par-dessus il. L'impact de nature extrêmement dynamique de creuse la tension persuadée par-dessus les soutiens naturels est observé pour être le facteur le plus sérieux pour la sûreté de fonctionnement sous une masse de rocher de toit dure et massive. En se basant sur ces observations, un modèle conceptuel d'interaction entre le soutien naturel et les couches recouvrant est discuté dans le papier.

Jan 1, 2003

By Yifan Ding, Shemek Oginski, Patrick Finn

The Manhattan section of the New York Water Tunnel No. 3 constructed by the Schiavone/Shea/Frontier-Kemper Joint Venture is a $668 million project. The contract includes a tunnel drive of 8.85 km (29,045 feet), tunnel lining of 14.77 km (48,468 feet)and construction of nine shafts ranging in depth from 143 m (469 feet) to 169 m(555 feet). Construction methods for excavation of the shafts are presented including raise bore, ground freezing, soil excavation, blasting, slashing, muck handling, rock support and shaft final concrete lining.

Jan 1, 2007

By Elmer R. Kaiser

G. A. Vissac (Consulting Engineer, Vancouver, B. C.) —Some of the data presented in this paper, in connection with cost studies of washed coals, should be clarified and qualified. Washing a raw coal down to a low ash content may mean higher losses in refuse, but the cost of the operation may be more than compensated by the increased value of the resultant product. However, careful engineering and accurate machinery are required to insure maximum profits. Washing at a low gravity separation demands a very accurate automatic process, chiefly when the small sizes of coal are being handled. Coal consumers today are buying mostly on a Btu basis, cognizant of the fact that low ash contents result in lower installation costs and in savings in handling and transportation charges. The attached Table X gives the actual balance sheets of the various cleaning operations corresponding to various ash contents for the two coals presented in the paper, using the old technique of a two-products separation. or the new technique, now commonly used in Europe, of a three-way separation made possible by new methods and new equipment. Savings in capital costs, handling, and transportation have been calculated on the basis of a delivered cost f.O.b. plant of $10.00 per ton of coal at 16.5 pct ash (actual 1953 average price reported by Consolidated Edison, N. Y.), and of $3.50 at the mine also for 16.5 pct ash coal. In both cases this corresponds to values of 126 and 4.26 per 1 pct of combustible and per ton, respectively, on delivered and on at the mine prices. As an example, the middle western coal at 16.5 pct ash, raw, washed down to 4 pct ash in a two-way process will give 53.75 pct of clean coal at 4 pct ash and 46.25 pct of refuse at 31 pct ash. The value of the losses will be 0.4625x(100—31)x0.042 = $1.34. Add the cost of washing, capital, and operation, which is $0.35. The total cost will then be $1.69. But with a three-ways separation we will have 53.75 pct of first-grade coal at 4 pct ash, 37.25 pct second-

Jan 1, 1955

By R A. Pax, B Cornish

Increasing the throughput of the MMG Century operation by over 25% from past practice to preserve cash flow close to the end of life of mine has revealed new throughput and load dynamic instabilities in the SAG mill causing significant time averaged loss of production. A twelve microphone array around the SAG mill (Pax, 2014) using the non-contact acoustic measurement methodology (Pax, 2011, 2012) has been used to diagnose the new dynamics. Dynamic acoustic noise signal information allows discrimination of the behaviour of the steel balls and the rock. Determination of mill load, toe and shoulder angles, water holdup, and proxies for mill load are possible.The instability was diagnosed with the help of an abnormality in the liners/lifters of the SAG mill with one row of lifters having a slightly increased in-mill life compared to the rest. The steel shoulder angle is observed to be disturbed cyclically at a rate of precisely one revolution at low throughputs of 750 t/h. However, at throughputs closer to 1100 t/h, the cyclic signal disappears indicating additional dynamics to randomise the repetitive behaviour of the mill charge. The cyclic signal has been used to operate the SAG mill with improved stability at 1100 t/h by adjusting the feed water addition rate.This paper presents and discusses these results and proposes the suggested origin of the extra dynamics. A small consistent aberration of the lifters circumferentially provides a useful detector of stable mill operation and a novel sensor for the dynamics of the internal operation of a SAG mill.CITATION:Pax, R A and Cornish, B, 2015. A novel measurement for the internal operation of a semi-autogenous mill using acoustic sensors – a case study, in Proceedings MetPlant 2015, pp 120–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By D. E. Andrews

The objective of this study was to investigate the environmental effects of slaking of surface mine spoils. To accomplish this, both field and laboratory programs were undertaken, supplemented by a thorough literature search. The field program consisted of drilling the highwall as well as test pitting in recent, two-, five, and ten- year-old spoil piles at four active mining sites in the eastern bituminous coal fields. Pertinent observations were made and samples collected for laboratory analyses which consisted of several standard geotechnical, agronomic, and geochemical tests. Durability tests utilized included jar slake, cyclic wet-dry, rate of slake, and slake durability tests. Correlation between field and laboratory portions was made- and results presented. The report is concluded with a discussion of the slaking process and associated environmental impacts, proposal of a preliminary classification system for use in premine planning, and presentation of management techniques to optimize the slaking process.

Jan 1, 1980

By Xuchen Fan, Chenyang Zhou, Yuemin Zhao, Liang Dong, Chenlong Duan

A gas–solid fluidized bed using magnetite particles is an effective methodology for coal beneficiation in the field of dry coal cleaning. Broadening the size range of magnetite used in the bed decreases medium preparation cost. In this study, a tapered fluidized bed was used to investigate a magnetite particle size range of −0.5 + 0.074 mm. The results showed that a tapered fluidized bed effectively strengthens mixing of magnetite with a wide size range (−0.5 + 0.074 mm). The results of beneficiation experiments indicated that with increasing tapered angle, separation efficiency increased and then decreased. The highest separation efficiency was obtained at a tapered angle of 10°. The optimal results showed that the ash content of the concentrate decreased from 31.82% to 12.33% with a probable error of 0.11, which indicated that a tapered fluidized bed was efficient to improve fine coal beneficiation performance.

By McHenry Mosier

The object of this investigation is to determine the field for the use of detachable bits in metal mines of the United States by correlating the data developed through the experience of mines using these bits. Most of the metal-mining districts in the Middle Western and Eastern States already have been visited. The purpose of the present circular is to define the problem and to discuss the factors that must be considered in order to determine, under different operating conditions, the advantages and disadvantages of this type of bit. Some of the data obtained to date are presented to emphasize points made in the discussion. It is hoped that, as the study progresses, a great many data on drilling will become available. It is evident that since in some cases these data will be confidential they cannot, therefore, be published except as they may be included in average figures covering several different mines. Some data already secured are of this nature, Although considerable information on drilling operations has been gathered at different mines, there were only a few instances in which there were available complete data on all the factors entering into the total cost of drilling with detachable bits and with conventional bits on regular drill steel.

Jan 1, 1936

Beatrix Gold Mine, a deep-level gold mine in the Free State province of South Africa, has the highest methane emission rate of any gold mine in the country. Methane is emitted from underground sources intersected during mining operations and is liberated into the general mine atmosphere. The total methane emission rate for the mine is of the order of 16001/s and the South section of the mine emits approximately 10001/s of methane gas. The mine has a history of gas accumulations which have led to a number of underground explosions. Following the last explosion in 2001 and the subsequent investigation, a number of recommendations were made. Two of these were to consider extracting the underground mine methane to render the mine atmosphere safe, and to declare hazardous locations that require special operating procedures. A number of such workplaces have now been declared at the South section of the mine. Methane gas is a potent, explosive greenhouse gas whose contribution to global warming and climate change is 21 times higher than that of carbon dioxide. To reduce its inherent danger and to mitigate its global warming impact, a carbon credit project under the Clean Development Mechanism (CDM) of the Kyoto Protocol has been developed and implemented, the aim being to capture and destroy the methane at Beatrix mine. The mine has constructed an extraction system to capture and extract 400 (Is of the methane. Percentage methane (per volume) of the gas intersected at source is 85%, with negligible concentrations of other hydrocarbons and water associated. The mine contracted the services of Group Five to design and construct the flare and ancillary equipment on surface, and Promethium Carbon was contracted to assist with the carbon¬-related aspects, approval framework, and administration of the project. A number of design and construction challenges had to be faced to extract and transport the gas effectively to the surface of the mine as the emitters are approximately 3 600 m away from the mine shaft at a depth of 860 m. Further considerations were the requirements for the type of column to be used to transport the methane gas, the pressure loss over the system, the safety systems needed to address the risk factors involved in the transport of the methane gas, and a suitable pumping system to extract the gas to the surface. The system operates under negative pressure provided by two blowers on surface delivering the emissions to a flare capable of burning off 450 8/s of methane gas. In this paper a number of benefits for the mine are discussed. These include, but are not limited to, the removal of approximately 55% of the total volume of methane gas from the general body of the air in the geographical areas of the mine where the methane gas is emitted into the atmosphere, and reducing the risk of methane-related incidents. A further benefit of this project is the mitigation of the global warming impact of the methane gas and the reduction of the mine's carbon footprint by approximately 25%. This project could also assist in alleviating the energy shortage being experienced in South Africa by means of the planned generation of 4 MW of electrical power, utilizing the methane gas, as a second phase of the project.

Jan 1, 2011

By Paulo Vinícius Souza da Conceição

A demanda por aços com baixos teores de enxofre tem propiciado o aprimoramento das técnicas de dessulfuração de gusa. O presente trabalho tem como o objetivo mostrar, através de um modelo em água, a influência da injeção auxiliar de gás através do impeller S.I.R.A.M sobre o tempo de mistura no processo do Reator Kanbara (KR) e sobre a área de contato desse gás com o líquido. Diferentes velocidades de rotação do impeller, vazões de gás injetado e pontos de injeção foram avaliados. Os resultados obtidos foram comparados com a condição de não injeção de gás. Observou-se que a injeção de gás é capaz de reduzir o tempo total de mistura.

Aug 17, 2017

By C. -T. Mutale, A. S. Tuling

Titanium can exist in three different oxidation states. Its oxides are numerous and in presence of iron and oxygen, iron-titanium oxide compounds can also form. Some of the oxides are non-stoichiometric, making the determination of the thermodynamic properties of titanium and its oxides in molten steel and in slag difficult. Therefore, for the assessment of titanium activity in molten steel using the electrochemical measurements of oxygen partial pressure, the identification of oxides in equilibrium with titanium is important. This paper reports on an investigation of solid titanium oxide inclusions, which have been identified by combining different methods of analysis on quenched samples. These samples were taken from a Fe-Ti-melt at 1600°C, quenched in cold water then mounted and polished for optical microscopy. The oxide inclusions were analysed using transmission electron microscopy (TEM) with energy dispersive spectroscopy (EDS). Both single crystal and polycrystalline diffraction patterns were used to identify the oxides by comparing the d spacings with those in the ICDD X-Ray Diffraction (XRD) database. XRD was used to analyse the oxide particles on the top of slow cooled samples. It was found in the TEM study that the similarity of the diffraction patterns of the various phases meant that unique identification was difficult to achieve in some of the diffraction patterns. However, TiO, Ti2O3, Ti3O5, Ti4O7were identified in quenched samples, while TiO2, FeO.TiO2and iron oxides were seen in slow cooled samples. It was also confirmed that the type of oxides is related to titanium content of the samples. Keywords: Titanium, Titanium Oxides, Iron, TEM, XRD, thermodynamic.

Jan 1, 2004

By Fisher N. I

Disequilibrium ratios (U3O8/eU3O8), which assess the degree to which gamma activity represents the uranium content of a sample, have been measured on a representative set of samples from the ore zone of a carnotite ranium deposit located at Yeelirrie, Western Australia. A statistical analysis has been performed to investigate the dependence of the ratios on lithology and on the location of the sample in the orebody. The analysis indicates that dependence on lithology and on position across the orebody is negligible. Samples from the western end of the orebody and those from below the water table level tend to have slightly lower ratios than samples from other positions, although these trends are small compared with a large random variation in the data. The large random variation could result from some redistribution of the daughter isotopes of uranium within the orebody. On the basis of the results from all the samples, the estimated deficiency of uranium relative to radium in the ore zone of the deposit is 11 per cent.

Jan 1, 1980

By Walter R. Storms

"INTRODUCTION The New Mexico potash exploration described herein was begun in February 1944 with the object of determining the amount of potash ore in the United States Potash Reserve in Eddy County by exploring the deposit from the surface with vertical drill holes. The work was completed in October of the same year after 16 holes had been drilled on the Reserve and in the immediate vicinity.The Potash Reserve is in secs. 26; 27, 34, and 35, T. 20 S., R. 29 E., Eddy County, N. Mex., about 14 miles northeast of Carlsbad, as shown on figures 1 and 1A, Drilling was done in secs. 26 and 35 of the Reserve, in section 14 to the north, end sections 2 and 56 to the east. All work was done on Governnent-owned, unleased land.The Reserve may be reached from Carlsbad by traveling to the north-east by automobile for about 14 miles on the paved U. S. highway 62. This highway passes through the southern part of the Reserve. Other parts may be reached by a State highway that passes along the eastern side of the area, then by poor dirt roads to various drilling sites. A branch of the Santa Fe Railroad also passes across the southern part of the Reserve enroute from Carlsbad to the plant and mine of the Potash Co. of America, a few miles northeast of the project and 22 miles from Carlsbad."

Aug 1, 1947

By L. C. Graton

[CONTENTS PAGE INTRODUCTION AND ACKNOWLEDGMENTS. By George M. Fowler2 Question 1-Is Structural Deformation of Some Character Always Necessary for the Migration of Mineralizing Solutions, Especially in Limestone or Other Dense Rock? DISCUSSION by: A. M. Bateman 10 S. F. Kelly 15 C. H. Behre, Jr 8, 13 G. B. Langford 13 T. M. Broderick11 H. E. McKinstry6 R. H. Clarke 13 D. H. McLaughlin8 J. D. Forrester for M. H. Gidel . . . 4 W. H. Newhouse13 G. M. Fowler 2, 6, 11 R. H. Sales 6 L. C. Graton 11 Edward Sampson 12 R. D. Hoffman 10 J. S. Stevenson 7 I. B. Joralemon11 L. B. Wright 2 Question 2-What Are Some of the Chemical and Physical Characteristics in Certain Beds within a Limestone Formation that Determine Their Favorable or Unfavorable Aspects as Reservoirs for Ore and Other Introduced Minerals? DISCUSSION by: G. W. Bain 17G. M. Fowler 21 C. H. Behre, Jr21L. C. Graton18 J. S. Brown 16G. F. Loughlin18 E. L. Bruce 19R. H. Sales 19 R. H. Clarke 20A. K. Snelgrove 20 Question 3-Are There Any Criteria by Which One Can Determine When Mining Operations Have Reached the Roots of an Ore Deposit? DISCUSSION by: J. M. Boutwell29G. B. Langford 29 T. M. Broderick28G. F. Loughlin25 E. Y. Dougherty27R. H. Sales 24 G. M. Fowler 22F. A. Thomson 26 I. B. Joralemon 22Edward Wisser 30 General S. F. Kelly35 References36

Jan 1, 1940

By C. F. Cornell, R. C. Emmett, D. A. Dahlstrom

FOR many years the disk-type and cloth-covered drum filters have found widest application in liquid-solids separation, which uses continuous filters. The disk type is less expensive, occupies less floor space per square foot of filtration area, and requires negligible down time for filter media changing. However, because filter cloth is billowed out by the blowback in the cake discharge, it is very short-lived if the scraper blades are set too close. Consequently cake weight is very important in assisting cake discharge, which normally necessitates a minimum cake thickness of 3/8 to ½ in. Also, the vertical position of the disks eliminates the possibility of efficient cake washing for removal of soluble values. The disk-type filter is generally limited, therefore, to applications that require no cake washing and form relatively thick cakes within the normal range of filter cycle times. The conventional cloth-covered drum filter is a more flexible unit, permitting wider variation in the percentage of cycle time devoted to cake formation, dewatering, or washing, as required by the application. Thinner filter cakes can be discharged because a horizontal line across the filter medium at the location of the scraper blade is equidistant from the edge of the blade at all points. The scraper blade therefore may be set a short distance from the filter medium or, where wire winding is not used, a floating scraper can be utilized so that the contour of the cloth can be followed. The drum filter is generally employed when there are difficult filtering slurries with resultant thin cakes or when cake washing to recover soluble values must be practiced. Difficulties sometimes encountered in continuous filter operation can be summarized in the following four categories: 1) Low filtration and/or washing rates due to blinding of the filter medium. 2) Poor cake discharge resulting from sticky cakes, filter medium blinding, or too thin a cake for the particular type of filter. 3) High filter media costs caused by short life and frequent down times for cloth changing. This results from blinding or from abrasion by the scraper blade when cakes are thin. 4) Blowback of filtrate at cake discharge because not enough air passes through the cake to purge the drainage area and filtrate lines during dewatering. To reduce or eliminate blinding tendencies several modifications have been tried, for example, cover-cleaning showers, blowback under the feed slurry, and snap-blow cake discharge. In many cases, however, this simply retards the rate of blinding, since the filter medium is kept clean at its outer surface only by these methods. As blinding usually occurs within or on the back of the medium, the operator is finally forced either to remove the cloth and scrub the medium intensively with a cleaning solution or acid-rinse it on the filter—all resulting in down time, short cloth life, and additional costs.

Jan 1, 1959

By James J. Neate

The augered cast-in-place pile system came into use in the late 1940's where various techniques were tried using pressure grouting methods. In the early development stages some piles were installed using the preplaced aggregate concrete system. As development continued it became more apparent that placement of coarse aggregate was more costly than making a pile out of a cement and sand mixture only. Various techniques were tried consisting of pumping structural grout into an open hole through a pipe left in the bottom of the hole, drilling or driving a pipe in close proximity to the tip elevation of the auger or in working a pipe down adjacent to the auger fluting. For these techniques the pipe was usually withdrawn after grout appeared at the surface. In 1951 a patent was applied for by Raymond Patterson describing the above techniques along with a technique for placement of grout using a hollow stem auger and a removable plug or lead bit at the tip of the auger. The plug or lead bit was removed by grout pressure and this would be an expendable item for each pile placed. The patent was granted in 1956 and patent rights were assigned to Intrusion-Prepakt, Inc. Shortly thereafter other contractors were granted licenses to utilize the system. Patent coverage expired in 1973 and this method now is in the public domain. Today the method is in wide use throughout the world and is particularly well accepted in Japan and England.

Jan 1, 1988

By K. Saikiran, A. R. Nalla

Longwall management, regular shield maintenance, and evaluation of ground control problems can be performed using real-time shield monitoring program. Based on real-time shield pressure data, evaluation of intensity and interval of periodic weighting, estimation of time-dependent pressure increase and the effects of geologic anomalies can be obtained. In this study, full-face shield pressure data of over 457 m (1,500 feet) of face advancement is analyzed to evaluate shield response in the presence of surface lineaments, floor undulations, and multiple main roofs. Shield pressure increase due to web cutting is also correlated with setting pressure during periodic weighting and normal time. In addition, time-dependent pressure increase rate on Sundays and holidays is also correlated with time average pressure and the location of previous periodic weighting.

Jan 1, 2000