Search Documents

By Henry P. Cole

A comprehensive review of published research was carried out to identify methods for teaching and assessing critical but nonroutine skills needed for coping with emergency situations. Specific methods for assessing critical skills proficiency in aviation, medicine, organization management, the military, and other industrial/technical workplaces are described. The potential application of these methods for teaching and assessing (1) critical first aid and (2) self-rescue and escape skills to underground coal miners in annual refresher training is explored. Research and development activities that may improve mine health and safety training are suggested. Most of these research and development activities were completed later in the project. This additional work is reported in the project technical report #2 and the final report. The research reported in the present document was completed in 1984 -85. Many of the initial findings reported in this document are updated in the later project final report.

Jan 1, 1988

By R. A. Jankowski, J. D. Potts

Four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner section averaged 0.59 and 0.26 mg/m3, respectively. The stageloader/crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feederbreaker contributed 0 to 0.2 mg/m3 of dust. A 1000 ft (305 m) increase in belt entry length or a 200 to 500 tons/shift (181,000 to 454,000 kg/shift) increase in production resulted in roughly a 0.1 mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 1992

Ensuring the success of a major resource development project, whether in the Gippsland Basin or elsewhere, is typically both a complex and costly process. It is therefore imperative from the point of view of the proponents of such a project - and in particular the financiers - that everything possible be done to minimise administrative confusion and delay in the establishment phase of the project, and to put systems in place which enable the project to run smoothly and efficiently in the later stages of its development and operation. An essential element in this process is ensuring that the project management is able to come to terms with and deal effectively with the relevant planning and environmental laws.

Jan 1, 1992

By Oscar Restrepo, Juan C. Nino, Henry A. Colorado

New and extraordinary physical-chemical properties of materials at nanoscale open up new applications for the building and infrastructure industry such as structural reinforcements, electronic properties and energy harvesting. Therefore the issues and risks associated with the manufacturing of nanomaterials are now of big concern due to the large volumes and typical processing involved in this industry. This paper presents a discussion and selected applications of nanotechnology in the construction and building materials: from metals and alloys, clay and minerals, ceramics, cement and concrete, asphalt, wood and composites, to finishing systems and some of the most used characterization techniques. Besides the progress in some areas, nanotechnology is just emerging in this field, with many challenges and opportunities, problems unsolved and business opportunities. A discussion regarding the potential health issues and risks of using nanomaterials for workers and the potential environment effects is included as well. New images and diagrams are presented and discussed.

Mar 1, 2018

By Everton Pizzio

Parafusos utilizados para fixação de partes submetidos a carregamentos cíclicos estão sujeitos a falhas por fadiga. No estudo do conjunto carcaça/corrediça de um compressor fixado por parafusos prisioneiros - ISO M24x3, que fixam o flange da corrediça falharam prematuramente por fadiga. O objetivo deste trabalho é desenvolver uma metodologia para otimizar o desempenho em fadiga do conjunto parafusado. Para tanto, foram realizados ensaios de fadiga visando o melhor processo de fabricação no desempenho em fadiga. Observou-se que o processo de laminação da rosca seguido de tratamento térmico é o mais adequado para o caso em estudo. A conclusão principal foi que a configuração atual de união do flange com a carcaça, resulta num baixo índice de aperto que é verificado através das cargas máximas que são transferidas diretamente ao parafuso e que aumentando o comprimento do parafuso através da inserção de uma bucha extensora, aumenta a vida em fadiga

Aug 17, 2017

By Jean-Claude LeRoy, Herman Keller

"INTRODUCTIONEROCON's work is the reclamation of mine wastelands. It has had considerable experience in particular in the reclamation of gold mine tailings in the Canadian Shield since the latter part of the sixties when most gold mines were closing down.A typical example is the famous Hollinger Mine in Timmins which produced $566 million worth of metal from 1910 to 1968 and had left behind some 56 million tons of tailings covering about 1,000 acres which were reclaimed on very short order and are now lush meadows of agricultural quality.To date, practically all gold mine tailings have been reclaimed once and for all by establishing a permanent, self-sustaining and maintenance free vegetation cover.RECLAMATION & THE MINING TOWNSThe first appreciation of people in a mining community where the tailings have been revegetated will be noticing one day the elimination of dusty conditions that used to arise formerly on every dry and windy day. In that respect, EROCON encourages not only vegetating the tailings but also the immediate surroundings of the mills and plants themselves at active mines. The elimination of windborne dust will result in an appreciable decrease in maintenance costs of plant and machinery and more pleasant working conditions for all."

Jan 1, 1975

By N. Sauret-Szczepanski, G. Patry, S. Gauthier, G. Potvin, C. Munger

Adsorption/thermal desorption with sorbent cartridges and analytical method using gas chromatography coupled to mass spectrometry (GC/MS) was developed for the determination of tetrafluoromethane (CF4) and hexafluoroethane (C2F6) emitted from primary aluminum smelters. A customized cartridge was built like a packed column with a stainless steel tube filled with a specific resin. The optimization of adsorption and desorption parameters was carried out to support the PFC sampling for all aluminum production technologies. The proposed method showed good linearity for concentrations ranging from 10 to 500 ppbv for CF4 and from 5 to 500 ppbv for C2F6 with correlation coefficients above 0.999. In certain conditions, the detection limits of the analytical method reached 0.3 ppbv for CF4 and 0.15 ppbv for C2F6- Using this methodology, a field campaign was carried out using a sequential sampler allowing the simultaneous sampling of PFC with cartridges and sampling bags. The results showed no significant difference (t-test) between the two sampling technologies and no breakthrough was observed from the cartridges .

Jan 1, 2006

By Brian Zelenko, William H. Hansmire

"By the time the latest expansion of the Washington Metropolitan Area Transit Authority (WMATA) system, known locally as Metro and which opened in 1976, is completed in 2020, the system will serve 97 stations and operate on 188 km (117 miles) of track on six interconnecting lines. Metro provides a critical transportation link to a population of approximately six million people within a 3,900-km2 (1,500-sq-mile) Washington Metropolitan area and has allowed job growth to expand to all corners of the region. In the 1950s and 1960s, when the system was first conceived and construction began, most jobs were centered in downtown Washington, and most of the workforce commuted by bus or car. Today, transit-oriented development has increased residential, commercial and government facilities near most of the existing 91 stations increasing the importance of the Metro system as a critical transportation link for the region. According to recent American Public Transportation Association (APTA) data, Metro is the second busiest transit system in the United States (after New York City’s transit system).During the nearly 50 years of construction on the Washington Metro system, technology improvements and lessons learned from the global tunneling industry were implemented. Portions of this background and history have been adapted from other work by the authors Roach et al. (2017) and expanded for use herein. For soil tunnels, these improvements included the change from a “two-pass” tunnel lining with a typical initial lining of steel ribs with wood lagging or segmental precast lining erected within the tunnel shield followed by a final lining of cast-in-place concrete to a one-pass lining system of pre-cast concrete gasketed segmental lining. Soil tunnels were originally excavated using open-face tunnel shields, but changed over time. By the late 1980s, tunneling using closed, pressurizedface tunnel boring machines (TBMs) using a one-pass tunnel lining consisting of segmental precast concrete permitted tunneling in a wider range of soil conditions with much less risk of damaging overlying utilities or structures, greater safety for tunnel construction personnel and without the need to dewater the soils. However, due to concerns about conditioning clays with earth pressure balance (EPB) TBMs, open face machines were still favored by contractors for their better advance rates, lower cost and ability to deal with boulders that were occasionally encountered in the Coastal Plain Terrace Deposits."

Jan 6, 2018

By Fletcher A. E W

Ever since it made its debut in 1962, in the form of a Robbins 31R, the raiseborer has become an accepted tool in the mining and civil construction industries. The first raiseborer to be used in the Witwatersrand goldfields made its appearance in 1968. This was a Robbins 42R which could raisebore 185m deep holes to 1,22m diameter. From 1968 to 1973 capability increased with the introduction of first the 61R, then the 71R and finally the 83R, which could raisebore 610m deep holes to 3,66m diameter. This created a demand for larger holes but the cost of bigger, more powerful machines requiring larger, stronger drill pipe, cutters and other accessories was prohibitive. To avoid replacing existing models such as the 71R, and in order to increase their capability, the concept of reaming in two stages sequentially was developed jointly by a German drilling equipment manufacturer, Wirth, their South African subsidiary, Transbor, and a local contractor, Rocbor Raiseboring and Mining Contractors. The result, the Sequential Reaming Head, proved most successful and existing machines, normally limited to 2,44m diameter holes, could now ream to 3,66m diameter. This created a demand for even larger holes. In order to maximise the use of the sequential reaming head to meet this demand the HG330, and subsequently the HG330SP raiseborer were developed. Using a 4,26m/6,02m cutting head, these machines have raisebored holes 1000m deep in hard rock. The raise- boring of the first major hole to be excavated by this combination, the 484m deep x 6,02m diameter surface shaft at Premier Mine is described. Reference is also made to six other shafts which have been completed or are under construction.

Jan 1, 1987

By Robert A. Jankowski, J. Drew Potts

In this U.S. Bureau of Mines study, four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner sections averaged 0.59 and 0.26 mg/m3, respectively. The stageloader-crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feeder-breaker contributed 0 to 0.2 mg/m3 of dust. A 1,000-ft increase in belt entry length or a 200- to 500-st-per-shift increase in production resulted in roughly a 0.1-mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 1992

By S. S. Hsieh, J. R. Lehr

Bench scale beneficiation studies were made on Idaho dolomitic phosphate rock using the TVA carbonate flotation process. The process used diphosphonic acid as a phosphate mineral depressant and fatty acid as a carbonate mineral collector. Silica was subsequently rejected as float using an amine collector, with phosphate product recovered as the sink fraction. Two samples of prepared flotation feed from commercial operation were used. One contained 21% P205 and 3.2% MgO. The other contained 26% P205 and 1.8% MgO. The results indicate that concentrates containing 31% to 33% P205 and 1% or less MgO can be obtained, with about 80% P205 recovery.

Jan 1, 1986

By H. Britton

This bulletin is the seventh in the series of petroleum bibliographies published by the Bureau of Mines, Bulletins 149, 165, 180, 189, 216, and 220 being compilations for the years 1915, 1916, 1917, 1918, 1919-20, and 1921, respectively. In this bulletin the same general plan of classification of references has been followed, but several additions have been made. ACKNOWLEDGMENTS Acknowledgment is made to the following organizations for the use of their libraries in the preparation of this bulletin: University of California, Stanford University, California State Mining Bureau, Union Oil Co. of California, Standard Oil Co. of California, and the Mechanics Mercantile Library of San Francisco; acknowledgment for their assistance is also made to H. H. Hill, C. P. Bowie, A. L. Foster, M. J. Gavin, H. C. Miller, E. B. Swanson, and Miss Louise Janssen, all of the Bureau of Mines, and to Miss Elizabeth H. Burroughs of the Union Oil Co. of California.

Jan 1, 1929

By Terry J. Close

The Welcome Creek Wilderness has small, dispersed gold placers. Pockets in the 25.5 million yd3 (19.5 million m3) of alluvium along Welcome and Rock Creeks have as much as $5.61 gold/yd3 ($7.34/m3) at $500/troy oz ($16.08/g). All the alluvium averages 20.1 cents gold/yd3 (26.3 cents/m3). Because of the low average gold content large-scale placer mining would not be economically feasible. Small-scale selective pocket mining, however, may be profitable. The alluvium along the streams in the Wilderness has little apparent potential for production of sand, gravel, or stone because alternate sources are closer to markets. The four lode prospects known within the Wilderness appear to have low mineral potential. No oil, gas, uranium, or geothermal energy sources are known to be present.

Jan 1, 1982

By Joseph L. Petrillo

In July 1997, Kvaerner Environmental signed a unique contract with Echo Bay Alaska called the Transfer Risk and Accelerate Closure (TRAC). The contract called for Kvaerner to assume the responsibilities and obligations associated with closeout of the Alaska-Juneau (A-J) Mine. Kvaerner is an international engineering and construction company with global interdisciplinary experience in the mining industry and environmental remediation. Echo Bay’s requirements called for Kvaerner to: •Provide a fixed price for closure with no change orders. •Negotiate, prepare and implement a final closeout plan as outlined by Echo Bay. •Complete a closure program that exceeded current regulatory requirements. •Improve, expand and maintain a proactive public and community relations program. •Hire Echo Bay employees where possible. •Provide adequate performance guarantees and judicial relief of environmental claims.

Jan 1, 1999

A mineral grain finder is described which is easily constructed to fit onto the stage of a standard reflected light ore microscope.The device is most useful in relocating particular grains or mineral associations on 30 mm diameter polished sections. The use of the grain finder in the teaching of ore microscopy is outlined.

Jan 1, 1988

By MEHMET KIZIL, PETER KNIGHTS, ROYAL REA

A 1/20 scale experimental dozer push test rig was designed and constructed to quantify the expected production rates (loose cubic meters per hour) for dozers operating in hard-rock bulk push applications. The particle size distribution of the material employed in the test rig was modeled on a fragmented muckpile representative of that for a typical surface copper/gold mine overburden. Buckingham Pi theory was applied to mathematically develop factors for scaling up dozer productivity parameters, including blade loads and push times. Dozer production rates were investigated for various dozing distances and slope angles. A series of instantaneous productivity curves were produced which are applicable for use in hard-rock dozer push operations. The productivity curves produced demonstrate that dozer productivity declines rapidly over the range of 10 to 40 m.

By Chris Brown

"The Island Copper plant was designed and built by Fluor Utah Ltd, in conjunction with Utah design staff, Originally designed to treat 33,000 tons/day (t/d) of ore, the current average milling capability is 38,000 t/d (Nov'74). The first of six semi-autogenous grinding lines was brought on line in October 1971, startup of the remainder being governed by equipment delivery schedules.The summer of 1973 saw the start-up of an additional three ball mills, and attainment of the present production level. The current process flowsheet is shown in simplified form.CRUSHINGThe crushing circuit is relatively simple, comprising single stage crushing of the ore followed by screening to fine and coarse fractions.The crusher is a 54 x 74in. Allis Chalmers Superior Gyratory with a setting of 9-lOin., driven by a 500-hp motor. Trucks dump on three sides of a rectangular dump pocket. An 84in. x 20ft. link belt apron feeder draws crushed ore from a 250-ton surge bin below the crusher, discharging onto a 72in. wide inclined steel cord conveyor belt. A fixed splitter box at the conveyor discharge separates feed to two parallel Jeffreys 6 x 20ft. vibrating grizzlies for screening into +4in. and -4in. fractions. The fractions are collected on short reversible conveyors which feed the coarse and fine ore stacker conveyors. Trippers distribute ore to outside stockpiles adjacent to, and above, the concentrator grinding 'floor."

Jan 1, 1975

The Iron Ore Company of Canada (IOC) is the largest manufacturer of iron ore pellets in Canada and its customer base covers North American, European and Asian steel producers. The company operates a mine, concentrator and a pelletizing plant in Labrador City, Newfoundland and Labrador, as well as port facilities located in Sept-Iles, Quebec. It also operates a 418-km (260-mile) railroad that links the mine to the port. IOC has approximately 1,900 employees. Its shareholders are Mitsubishi Corp. (26.18 percent), Labrador Iron Ore Royalty Income Fund (15.1 percent) and the international mining group Rio Tinto, which is its major shareholder (58.72 percent) and operator, with activities in more than 40 countries throughout the world. The IOC was incorporated in 1949 and by 1954 it had completed the Quebec North Shore and Labrador (QNS&L) rail line. IOC began mining in Schefferville, Quebec by 1954 and closed those operations down in 1982. In 1962, IOC commissioned the present day Carol Project consisting of mining, concentration and pelletizing facilities in Labrador City, Newfoundland. In 2004, IOC shipped its one-billionth tonne of ore on the QNS&L Railway. In 2005, IOC celebrated 50 years of mining history. The company expressed an interest in reducing the amount of oversize material (>1 m x 1 m x 1 m or 3.2 ft x 3.2 ft x 3.2 ft) being produced and its subsequent downstream effects, including in-pit sorting and reduction, damage to mobile equipment and significant delays in the loading pockets and the primary crushers. To achieve this goal, an oversize reduction project was undertaken by the mine that, to date, has significantly improved upon baseline measures. One key approach used to reduce the amount of oversize was the implementation of thicker emulsion. The introduction of a thicker emulsion provided more resistance to the forces created by dynamic water and reduced the infiltration of the emulsion into the cracks and fissures of the rockmass, resulting in reduced amounts of oversize and more consistent fragmentation throughout the muckpiles. Additionally, a significant reduction in nitrates leached into the mine water discharge has been realized. To determine the effectiveness of the oversize reduction project, IOC used a first-of-kind technology to assess fragmentation presented to the shovel at the digging face. A digital vision system (DVS) was installed on one of the shovels to capture images that were stamped with GPS locations. A large population of digital images were analyzed to produce a robust fragmentation distribution baseline that was used as one of the mine key performance indicators (KPI). Changes to blasting practice were subsequently measured against the baseline KPI to assess effectiveness.

Jan 1, 2011

By A. J. Vivyurka

"This is a talk about the experiences that Rio Algom Mines Ltd. has had in the Elliot Lake uranium area trying to make the tailings more compatible with the surrounding environment. To get a better idea of the problem that we are associated with we have to go back to the location. The Elliot Lake uranium area is situated about half way between Sault Ste Marie and Sudbury and is about 20 miles north of Lake Huron. In 1950, uranium was discovered along the north shore of Lake Huron and by 1961 we had up to 9 mines operating in the area. Then the United States Atomic Energy Connnission withdrew their contracts so that at present there are only 2 mines operating. From all the mines that we had operating, we ended up with 7 tailings areas. From these 7 tailings areas we have 5 sites where we have active treatment or rehabilitation. There is the Pronto site where we are treating uranium tailings and copper tailings. There is the Lacnor-Nordic site which is located just out of Ellio Lake. The Milliken-Stanleigh site is in the Crotch Lake area. The Panel tailings is off the north end of Quirke Lake and finally there is the operating property of Rio Algom Mines at Quirke Lake.To understand fully the problem with this rehabilitation we have to look at the constituents of the ore. The ore body is a quartz conglomerate with uraninite and brannerite as the uranium bearing minerals in a fine ground mass of quartz, sericite and pyrite which separates the larger quartz pebbles. The approximate composition of the ore is: 80% quartz, 13% chlorite, 7% pyrite and 0.2% uranium minerals. The processing method also adds a few constituents to the final tailings."

Jan 1, 1975

By F. W. Clark

At the present time, when lixiviation versus amalgamation is being so thoroughly discussed by practical men, and published information is so meagre, the following tests, made by students in the mining laboratory of the Massachusetts Institute of Technology, may be of interest to others. The ore experimented upon was obtained from the Sombrerete mines near Zacatecas, Mexico. A careful analysis of the dried sample resulted as follows : Per cent. SiO2,............62.79 S.............13.86 Al2O3............4.39 Fe,............11.26 Zn,............1.57 CaO.............2.91 MgO,........... 0.06 Cu,.............0.12 Pb,.............0.40 Sb and As,..........trace CO2,............2.35 Ag,.............0.16 99.87

Jan 1, 1886