Search Documents

By F. R. Lee

When the Bureau of Mines was established in July 1910, one of the problems immediately attacked by the new organization was the development of standard, for the design and testing of electrical equipment that could be used without fear of initiating fires and explosions in underground coal mines. Research and investigation by Bureau personnel, supplemented by the published results of similar work by European mining authorities, led to the establishment of standards or "schedules." which guide manufacturers ill the design of many types of electrically operated machines and devices used in underground coal Mining. By issuing these standards, Bureau personnel establish the requirements to be met by such equipment before it tan be approved by the Bureau of Mines as permissible for use in gassy coal mines. Every 2 years the Bureau of Mines publishes a list of equipment that leas been accepted as approved or permissible during the preceding 2 calendar years. This is done to inform the mining industry of the availability y of the latest equip¬ment for safe use underground.

Jan 1, 1964

By F. R. Lee

[WHEN the Bureau of Mines was established in July 1910, one of the problems immediately attacked by the new organization was the development of standard, for the design and testing of electrical equipment that could be used without fear of initiating fires and explosions in underground coal mules. Research and investigation by Bureau personnel, supplemented by the published results of similar work by European mining authorities, led to the establishment of standards or "schedules." which guide manufacturers in the design of many types of electrically operated machines and devices used in. underground coal Mining. By issuing these standards, Bureau personnel establish the requirements to be met by such equipment before it tan be approved by the Bureau of Mines as permissible for use in gassy coal mines. Every 2 years the Bureau of Mines publishes a list of equipment that leas been accepted as approved or permissible during the preceding 2 calendar years. This is done to inform the mining industry of the availability of the latest equipment for safe use underground.]

Jan 1, 1964

By E. J. M. Jahnsen, I. Jauhari, T. Badrujaman, F. A. Stober, B. O. Wasmund, L. R. Nelson, T. Miraza, J. M. A. Geldenhuis, A. Taofik Hidyat

The role of dedicated operational support in the ramp-up and stabilisation of the FeNi-II furnace for ferro-nickel production at PT Antam?s smelter located in Pomalaa, Indonesia is described. The furnace was uprated to 32MW capability in a rebuild performed in 2005. This primarily involved installing a larger transformer, coupled with adoption of HATCH water-cooled copper plate, waffle and flanker coolers with integrated metal and slag tapblocks, HATCH air-cooled copper fin lower sidewall cooling and HATCH vertical sidewall binding system ? ?holddowns?. Following a smooth commissioning period, the progress in attaining the preliminary ramp-up target load of 24MW is described. This initial target was set by Antam, subject to some prevailing smelter equipment constraints, particularly kiln capacity. Stabilisation of the furnace operation is discussed, together with some of the specific commissioning and operational challenges surmounted by the joint Antam-HATCH team. These included: ?Mastering furnace integrity monitoring and operation with copper coolers, especially metal tapblock planned maintenance and repair strategies; ?Transition from traditional ?immersed electrode? to ?brush-arc? mode of operation approaching as closely as possible to the productive ?shielded-arc? mode of operation within existing equipment constraints; ?Reductant selection and control issues; ?Utilising the sophisticated furnace monitoring to provide detailed indication and warning of potentially destructive furnace upset conditions such as Si reversion and CO boils.

Jan 1, 2007

Institute of Metals Division Ferrous and Nonferrous Physical Metallurgy Established as a Division April 26, 1918 (Bylaws published In the 1944 TRANSACTIONS Volume of the Division) A A SMITH, JR, Chairman E A ANDERSON, Past-Chairman F N RHINES, Senior Vice-Chairman W A DEAN, Vice-Chairman H A MALONEY, Treasurer ERNEST KIRKENDALL, Secretary 29 West 39th Street, New York 18, N Y Executive Committee R M BRICK 2 W A JOHNSON 1 H I DIXON 2 E W PALMER 1 M GENSAMER 2 J H SCAFF 3 J D HANAWALT 1 J D SULLIVAN 3

Jan 1, 1952

By John H. Soule

The Torpedo Copper mine in the Organ Mining District, Dona Ana County, N. Mex., was discovered In 1899. Production was begun immediately and continued until 1907. Since 1907 very little ore has been produced, although Many individuals and companies have been interested in the property at one time or another. Approximately 6,621 feet of diamond-core had been completed on the property before 1949. The results from some of this drilling were unsatisfactory because of the poor core recovery. In addition to its investigation of the Torpedo ore deposits, attention was given by the Bureau of Mines to obtaining better core recovery through the use of special equipment and techniques. This project was begun October 3, 1949, and was completed April 30, 1950. Four diamond-drill holes totaling 2,140.5 feet, which includes 18.2 feet of overlap in a deflected hole, were drilled. All drilling was done with a Government-owned hydraulic-feed drill with some special rods and core barrels, in addition to the usual equipment. The over-all core recovery was 89.5 percent. Omitting the drilling in overburden where little or no core was desired, the recovery was 94.6 percent. Core recovery in the ore zones averaged 95.2 percent. This paper describes the location, the general features of the area, the geology, the Bureau of Mines procedures, and the results attained by these procedures.

Jan 1, 1952

By Alla D. Mah

The need for more and better basic thermodynamic data for the oxides of many of the rare metals is evident to anyone who attempts thermodynamic calculations involving these substances. In continuation of a Bureau of Mines program to meet this need, this paper reports new experimental values of the heats of formation at 298.15° K. of the hexagonal crystalline variety of germanium dioxide and germanium dioxide glass. The values were obtained by means of combustion calorimetry and sodium hydroxide-solution calorimetry. The calorimetric results also made possible the derivation of values for the heat and entropy of fusion of hexagonal germanium dioxide at its melting point. The newly measured data were combined with previously known entropy and high-temperature heat content values to obtain heats and free energies of formation of germanium dioxide (in the hexagonal crystalline, glassy, and liquid states) over the temperature range from 298.15° to 2,000° K.

Jan 1, 1962

By Z. Botha

Sheryl Sandberg, the COO of Facebook, published a book titled 'Lean In', where she invites women to sit at the table. In summary, to 'sit at the table' entails not only embracing opportunity, but to actively seek out opportunities in leadership positions. Sandberg points out that, unfortunately, apart from institutional obstacles, a woman's own perceived limitations have a negative impact on her leadership ambitions. To create an environment where diversity will flourish, where everyone has a seat at the table and everyone has a voice, safety must be established first. To establish safety within a diverse team, there is power in relationships and connections. This study will first and foremost review theories in literature as to why diversity and inclusion are so important and the value that diversity brings to our industry. The study also recommends a few focus areas for improving diversity and inclusion in the industry.

Sep 1, 2022

By Manqiu Xu, Joe Holmes, Peter Wells, Peter Langlois, Germain Labonté, Jim Barrett

"The flowsheet for the Voisey’s Bay mill had to meet the challenge of processing an ore containing high pentlandite and chalcopyrite values in a largely pyrrhotite/troilite matrix. In the 1994-97 period, circuit development focused on making a high-grade copper concentrate and a relatively low-grade nickel concentrate. However, in 1998 a circuit with copper concentrate, high-grade nickel concentrate and a Ni/Cu middlings concentrate was specified. Following a three year project delay, work resumed on the flowsheet in 2001, and the target for the overall grade of the nickel concentrate was raised from 14% to 20% nickel. To achieve this target triethylamine tetramine (TETA) and sulfite pyrrhotite depressants were used in an all lime circuit. It later became evident that, with appropriate selection of collector and adjustment of the circuit by the addition of a scavenger on the scavenger cleaner, it would be possible to approach the grade of concentrate required without the use of pyrrhotite depressants. The recycle of water and the contained thiosalts was also proven to be instrumental in raising the grade.Construction and commissioning of the mill were fast-tracked with start-up of the mill in September 2005 some six months ahead of the original schedule. Ramp-up of both throughput and metallurgy was faster than any other recent nickel installations with tonnage being limited mainly by concentrate dewatering due to the higher than initially planned ore grades.INTRODUCTIONNickel was discovered in the vicinity of Voisey’s Bay by Chislett and Verbiski working for Diamond Field Resources in 1993 and the Ovoid deposit was delineated in the winter of 1994/95. By the end of 1995 the Ovoid had been well explored and at that time was thought to have a reserve of at least 30 million tonnes with an average grade of 2.83% Ni and 2.0% Cu. Drilling to the east of the Ovoid had indicated the presence of significant mineralization. In June of 1995, Inco Limited bought a 25% share in the Voisey’s Bay Nickel Company (VBNC) which was a subsidiary holding company set up by Diamond Fields. Inco also bought 8% of Diamond Fields and negotiated the right to sell all the nickel produced from VBNC for twenty years as part of this agreement. In April 1996, Inco bought the 75% of VBNC shares that it did not own."

Jan 1, 2007

By Axel Pankewitz, Andrew Smith, Mathias Stender, Christian Behrens

"Particle size measurement is one of the most important factors in obtaining peak performance of the mineral processing plant in order to ensure efficient milling and flotation circuit operation. Off-line particle distribution analysis technologies only allow an infrequent check of the ore slurry size and hence do not allow for timely process monitoring or intervention. Most existing on-line particle size analysers suffer from a variety of disabilities such as poor statistics, non-representative sampling or mechanically complex setup. This paper will describe an Ultrasonic Extinction based method which overcomes many limitations of existing online analysers and has proven its performance for mineral applications over many years. Installation examples will be given. Since new technologies usually raise e questions about comparability and agreement to common particle size analytical methods e.g. sieving or laser diffraction analysis, extensive studies were performed comparing these different technologies to quantify the quality of results as well as its mathematical robustness."

Jan 1, 2014

By E. Watkins, J. C. LeRoy, A. Vivyurka

"TAILINGS REVEGETATIONWelcome to the Revegetation Session. My instructions are to introduce the Speakers and to provide a general introduction.I do the latter with humility not only because of a lack of personal experience or because tailings revegation is not well established technology, but because any general statement on a country or industry as diverse as the Canadian Mining Industry is bound to be wrong somewhere.Laying aside normal standards of accuracy I proceed as follows:In considering the question of tailings revegetation, one asks two basic questions:1. What ought to be done?2. What can be done?The first question can be broken down into three kinds of criteria or objectives:a) Legislativeb) Technicalc) AestheticThe first I leave to the politicians and the last I will avoid. Aesthetics is the philosphy of taste. It is concerned with the appreciation of things rather than what they really are. It is much easier to get into an argument on aesthetics than to get out of it feeling you have said something of consequence.Technical criteria can be divided into the following sub-objectives: 1. To isolate the tailings basin so surrounding land is not degraded. The first step here is stabilization of the surface to prevent wind and water erosion."

Jan 1, 1975

By S. Murdock, R. L. Fleischer, H. W. Alter, J. E. Gingrich

The use of solid state track deters allows totally passive, integrating measurements of 222Rn (radon) or of 220Rn (thoron) plus radon. A track-detecting solid is placed in a holder that is closed by a selective membrane and exposed to the atmosphere of interest to produce an accurately time-averaged record over times of interest that range typically from a week to a year. By selection of the proper membranes, dosimetry can be done for radon or for the sum of radon and thoron. A different membrane is appropriate for measuring radon under humid conditions such as are found in the ground. Large numbers of measurements have been made with these systems both in the ground, where radon levels are high, and in indoor environments, where levels are orders of magnitude less. Calibrations have been carried out at both high and low concentrations of radon. New results in the air at the site of the Shirley Basin mine and mill give reproducible results with month-long integrating periods. The off-site background levels are in the range 0.7 to 1.0 pCi/l (26-37 Bq/m3). The average yearlong on-site level is 1.5 pCi/l (56 Bq/m3); at the mill it is 2.6 pCi/l (96 Bq/m3); and the level measured at the backhoe in the open pit mine is 3.9 pCi/l (144 Bq/m3). The region of significantly elevated radon levels is confined to a radius of 1.6 km of the mine and mill. All of the on-site radon concentrations are less than but comparable to the typical values found in the living areas of modern energy-efficient homes.

Jan 1, 1981

By Yoginder P. Chugh

Subsidence may be observed above partial extraction shallow room-and-pillar mines where the coal seam(s) is associated with weak and thick claystone in the floor. This paper presents results of subsidence studies at such a mine. During the 26-month study period, a time dependent subsidence causing a maximum vertical movement of 50 mn was observed. After a subsidence rate of 6.0-6.5 m/month for the first two months after development of mine workings, the rate decreased to 0.8-0.9 mm/month after 17 months. However, presumably due to settlement of barrier pillars, it increased therafter to 1.7 mm/month for the next 9 months. Angle of draw, based on zero subsidence, was calculated to be about 29 degrees. Maximum tensile strain and compressive strain values observed were 0.040 pct and 0.039 pct respectively. A hypothesis was fomlated to correlate surface subsidence movements with observed underground movments. The data collected to date fits reasonably well within the formulated hypothesis.

Jan 1, 1989

By Roshan B. Bhappu, Zeki M. Dogan

Two magnesite ores containing 3.15% and 8.73% SiO2 and a calcined magnesite product assaying 2.6% Si02 were first reduced in size to -20 mesh by roll crushing. 'They were then treated dry on a high intensity magnetic separator to reduce their silica content by rejecting iron-stained silicate minerals in the magnetic fraction and obtaining marketable magnesite or calcined magnesite as a nonmagnetic product.

Jan 1, 1975

By Brian Danyliw

"Dust control is an increasingly important consideration for all mining operations from a health, safety, environmental and maintenance perspective. Modern mining operations incorporate a variety of mechanical dust control techniques into design however in many cases these engineered systems are unable to meet desired fugitive dust level targets. In these cases a variety of chemical dust suppression options are available to operators to assist in meeting their targets. This paper provides an overview of available chemistries, discussion of application techniques and equipment requirements and available performance monitoring technologies. This paper will also include a number of case histories discussing the treatment approach chosen, challenges encountered, chemical feed, storage and application equipment, monitoring techniques employed and results achieved.INTRODUCTIONDust FundamentalsFugitive dust by definition is an aerosol consisting of particulate matter suspended in a gaseous medium. Aerosols can include suspensions of particulate (solids) or sprays (liquids) or a mixture of both. Of particular concern from an occupational health and safety perspective are aerosols of particulate matter due to their involvement in classical occupations lung diseases such as silicosis, poisoning through chronic exposure to compounds such as lead and beryllium and expected involvement in more modern identified conditions such as cancer, asthma, and a host of other respiratory and non-respiratory conditions which may be caused or influenced through exposure to dust.According to the ""Glossary of Atmospheric Chemistry Terms"" (IUPAC, 1990), ""Dust: Small, dry, solid particles projected into the air by natural forces, such as wind, volcanic eruption, and by mechanical or man-made processes such as crushing, grinding, milling, drilling, demolition, shoveling, conveying, screening, bagging, and sweeping. Dust particles are usually in the size range from about 1 to 100 µm in diameter, and they settle slowly under the influence of gravity."" It should be noted that the behavior of particulates with respect to settling rate in air is a function of particle mass and shape and therefore the geometric size of the particle can be misleading. Occupational hygienists utilize the concept of particle aerodynamic diameter as a more representative reflection of particle size. Particle aerodynamic diameter, is defined as ""the diameter of a hypothetical sphere of density 1 g/cm3 having the same terminal settling velocity in calm air as the particle in question, regardless of its geometric size, shape and true density."" The expression of particle size as aerodynamic diameter allows for a more consistent understanding of particle behavior both from a settling perspective as well as from the perspective of how dust particles will behave in the respiratory tract. Figure 1 illustrates settling rates for particles of various aerodynamic diameters. The relationship between particle size and settling rate is important for understanding what size of particles must be addressed by dust control strategies as well as what particle sizes represent the most danger from an exposure and occupational health perspective."

Jan 1, 2015

By J. F. Hutwelker

A pilot plant was constructed and operated to investigate the column flotation of 20 x 200 mesh North Carolina phosphate ore, using high throughput, high solids operating conditions developed at the NCSU Minerals Research Laboratory. Flotation was performed at 45% solids in a 9.5 cm (3.75 in.) diameter by 2.26 m (7.4 ft.) tall column at throughputs of 19.1 t/hr/m2 (2.0 stph/ft2) and 31.7 t/hr/m2 (3.3 stph/ft2). Recoveries in excess of 98% of the phosphate value were obtained at the lower throughput -- while obtaining concentrate grades containing over 28% P205 (61.2% BPL) at that recovery. Recoveries of about 95% of the phosphate value were obtained at the higher throughput, while making a concentrate averaging 27.6% P209 (60.3% BPL). In addition, a better understanding of the variables governing the column flotation of coarse nonmetallic minerals was gained. Low air flow rates adversely affected concentrate grade at the lower throughput. At the higher throughput, phosphate recovery decreased at an elevated air flow rate. An unexpected result of the study was the effect that frother type had upon phosphate metallurgy. Use of Nottingham Econofroth 925 provided better flotation selectivity than American Cyanamid F-65 at the low throughput. This is significant since the high' throughput tests were conducted with F-65 exclusively. It is reasonable to expect further improvement in high throughput performance when the optimal frother type and dosage are determined.

Jan 1, 1993

By Y. Yhang, D. C. Sego

ABSTRACT This paper evaluates the potential of freeze-thaw dewatering using Albian mature fine tailings (MFT). Freezing tests were first performed to study the effect of freezing rate on dewatering efficiency. Lower freezing rate resulted in higher thawed solids content and shear strength. Subsequently, large strain consolidation tests were conducted to investigate consolidation behaviour and how it is affected by freeze-thaw. The consolidation behaviour was presented in terms of effective stress versus void ratio and permeability versus void ratio. The results can be used to predict the field behaviour of Albian MFT and optimize the application of freeze-thaw for MFT dewatering.

Jan 1, 2014

By George Joseph Malina

Contractor chose and Owner allowed concrete to be placed using the arch first principle while excavating the 35'-3" O.D. rock tunnel. The contract included excavating and lining 26,000 L.F. of rock tunnel to 33'-I.D. Concrete was placed at a rate of 90LF per working day using a movable bridge to allow batching, mixing and pumping of concrete adjacent to the tunnel form.

Jan 1, 1981

By Duberney Hincapié-Ladino

O presente trabalho estuda os parâmetros de permeabilidade de hidrogênio de um tubo API 5L X80, e uma chapa de aço grau X80, onde a principal diferença está na composição química, o primeiro contém 0,07%C e 0,04%Nb e o segundo 0,04%C e 0,102%Nb. As amostras foram cortadas com espessura de aproximadamente 1 mm, lixadas e recobertas com um filme de níquel, em uma das faces. Nos ensaios de permeabilidade foi utilizada uma célula modificada tipo Devanathan-Stachurski, com a solução A da norma NACE TM0284, com injeção de H2S no lado de geração e 0,2M NaOH no lado de detecção. As curvas de corrente em função do tempo obtidas passaram por tratamentos matemáticos (método tlag), permitindo a obtenção dos parâmetros de difusividade aparente, concentração máxima de hidrogênio e número de traps (sítios de ancoramento). Tais parâmetros mostraram-se iguais para os dois materiais. As curvas foram normalizadas e modificadas de maneira a eliminar o efeito da espessura das amostras. Estas novas curvas foram comparadas com o modelo teórico da segunda lei de Fick. A comparação evidenciou que o procedimento inicial para a obtenção dos parâmetros de permeabilidade mostra-se eficiente e vantajoso por apresentar maior praticidade. Pôde-se concluir que a semelhança no comportamento dos parâmetros de permeabilidade foi devida às similaridades nas suas microestruturas. Os resultados obtidos no presente trabalho evidenciam que o tipo e quantidade de traps nestes materiais são determinados pela microestrutura.

Aug 17, 2017

In the past decade, the increased engagement of business in debates around sustainable development has prompted recognition of the importance of biological diversity at the local, national and global scales. Driven by increasing populations that demand rising real incomes, a range of human induced pressures are modifying natural habitats and diminishing their ability to support life. Public policy changes have struggled to arrest the loss of habitats such as wetlands or tropical forests, and the related extinction of plant and animal species. Although conservation legislation and regulation were once the exclusive responsibility of government, new partnerships are now being forged that increase the role of the private sector and non-government organisations (NGOs) in developing and delivering conservation initiatives. Since the mid 1990s Rio Tinto has had to adapt to meet the demands of a rapidly changing conservation landscape. When Rio Tinto adopted its statement of business practice in 1998 The way we work, it explicitly recognised the need to take account of relevant environmental factors in obtaining access to lands, particularly in designated areas of high conservation value. With the revision of The way we work in April 2003, the policy on land access was strengthened through removal of the word ?designated?, thereby signalling recognition of the importance of biodiversity outside of protected areas. In addition, Rio Tinto?s revised land access policy explicitly refers to the use of land that is surplus to operational requirements for habitat protection and biodiversity conservation, subject to social considerations. In late 2003 Rio Tinto further strengthened its commitment to biodiversity with the promulgation of its biodiversity strategy and related position statement, biodiversity principles? (See Appendix 1.1) and technical guidance documents. This commitment is also embodied in a variety of initiatives at the corporate and operational levels, which are reported on annually in Rio Tinto?s Social and environment review. This guide has been prepared to support the practical implementation of Rio Tinto?s biodiversity strategy. The purpose is to provide guidance on how to effectively integrate biodiversity into Rio Tinto?s operations. It is applicable to all Rio Tinto exploration, new development projects and operations, irrespective of whether they have been operational for some years or are at the beginning or end of their operational life cycles. This guidance has been developed to support the Rio Tinto Environment Standards and the Rio Tinto Community Standard and any additional supporting documents as they are developed.

Apr 1, 2005

By C. Lorimer Colburn

"The diverting of men from industry to combat in the world's war focused the attention of the operators in this country upon mechanical means of doing things. The demand for man-power -was so insistent that every available agency for multiplying it had to be employed. It was during the 1period of the war and immediately thereafter that development of the use of underground loading devices made most rapi4 progress. In all parts of the United States, mining engineers and mine managers were diligent in their efforts to develop mechanical loaders. The mining engineers of the U. S. Bureau of Mines in every section of the country have secured, with the cooperation of the mine operators, data on the actual performance of the mechanical shovels in their districts, and have made them available to the author of this paper.No effort has been made to discuss exhaustively the subject of underground loading devices. It has been the object to collect together in one paper, records of the performance of all machines now in actual use. Improvements in the design of machines are constantly being made the performance records given in this paper relate to operation prior to March 1 1 1921. The records prior to 1920 cay not fully represent the work that could be accomplished with the present models of the same machine.The data secured are given exactly as reported by the mine operators. Since this data were collected there have been two underground loaders, of a different design, put into operation in the iron mines of the Lake Superior District. One is the John Mayne Sub-level loader, being tried by the Cleveland-Cliffs Iron Co., Ishpeming, Mich., and the other is the Cole-Goudie shovel, being tried by the Oliver Mining Company, at Ironwood, Mich. No information has been secured regarding the performance of either of these machines."

Oct 1, 1921