Search Documents

By David Hopkins, Steve Klein, Bradford Townsend, Ed Sum, Derek Penrice

INTRODUCTION The Transbay-Caltrain Downtown Extension (DTX) Project involves the construction of an approximately 1.5-mile rail line that will extend Caltrain commuter service and the future California High Speed Rail system into downtown San Francisco. The underground rail extension will be constructed by mined tunnel and cut-and-cover methods. Tunneling challenges include difficult ground conditions, low rock cover, the presence of historic buildings along the alignment, and the large tunnel span, ranging from approximately 50 to 65 feet. Three mined tunnel construction methods were evaluated: the Stacked Drift Method, the New Austrian Tunneling Method/Sequential Excavation Method (NATM/SEM), and Tunnel Boring Machines (TBM). This paper describes the challenges presented within the mined tunnel section, and summarizes the evaluation of tunneling methods that led to the selection of NATM/SEM. PROJECT OVERVIEW The existing Transbay Terminal opened in downtown San Francisco in 1939. This facility is antiquated, and does not meet current building seismic safety standards or the transportation needs of the Bay Area. For these reasons, San Francisco voters approved Proposition H in 1999, which proposed to construct a new or rebuilt regional transit center at the site of the existing terminal and extend Caltrain commuter rail ser-vice to the new transit center. The new transit center is the hub of the Transbay Transit Center (TTC) Program, which will greatly enhance regional transit service by providing connectivity for six Bay Area transit providers at one facility. The program will be the largest inter-modal centerwest of New York City. The TTC Program is comprised of two major projects, the Transit

Jan 1, 2007

By Richard B. Moore

This bulletin presents a summary of available information regarding the sources of uranium, radium, and vanadium, the methods used in treating the ores, and the uses of the finished products. In particular the paper describes the ores found in the United States, giving especial attention to those characteristics of the ores and the conditions of their occurrence that affect mining and treatment. ACKNOWLEDGMENTS. In the preparation of this bulletin a number of persons rendered assistance by furnishing information and by making it possible for us to visit the carnotite deposits in western Colorado and eastern Utah at a time of the year when without this assistance it would have been difficult to obtain satisfactory results. We desire to express our thanks to the following persons: Henry Hall, W. L. Cummings, T. V. Curran, K. D. Hequembourg, David Taylor, H. C. Brown, Forbes Rickard, George W. Alsdorf, Dr. Herman Fleck, Orr J. Adams, C. S. Cherrington, Newt. Stewart, O. B. Willmarth, Angus Cameron, George A. Head, and Lorimer Bros.

Jan 1, 1913

By G. A. Mallory

"The South Bay Division of Selco Mining is located fifty-four miles northeast of Ear Falls Ontario on Confederation Lake. The concentrator operates five days a week and processes six hundred tons per day of copper zinc silver sulphide ore. The concentrator is comprised of crushing, grinding, differential flotation, thickening and drying circuits. The major constituents of the concentrator feed are: chalcopyrite 7%, sphalerite 20%, pyrrhotite 3%, pyrite 25 - 30% and felsitic volcanics 40 - 50%. The mine went into production in March 1971 with an anticipated three year life and is now scheduled for closure in the summer of 1981. Recent mine production has been limited to three cut and fill stopes which have widely varying ore grades, therefore mill feeds vary from 0.25 to 4% copper, 3.5 to 27% zinc, 0 to 0.4% lead and 15 to 30% iron.In mid 1977 Selco negotiated a six month rental purchase agreement with Outokumpu Instruments Canada Limited for a five stream analyser system. The Minexan 202 probes were the first Outokumpu probe type analysers installed in Canada although Outokumpus' Courier systems are well known. Installation of the system took place in April 1978 and after numerous hardware faults the six month evaluation began in August. By December it was obvious that the Minexan 202 probes with proportional detectors did not have adequate resolution to determine low copper values in either of the tailings streams. Outokumpu offered to replace the tailings analysers with a new prototype solid state detector probe the following summer. The evaluation on the five Minexan 202 probes continued until August 1979 when the new solid probe was installed. The Minexan S (solid state) probe was evaluated with the three remaining Minexan 202 probes until December 1979 when Selco elected to purchase the system."

Jan 1, 1981

By Mark K. Larson

Researchers at the U.S. Bureau of Mines have developed a FORTRAN computer program that can calculate stress states from overcoring measurements obtained from hollow inclusion cells, triaxial cells, strain gauges installed on the wall of a bored raise, doorstopper gauges, borehole deformation gauges, or a combination of any of these gauges. Such stress states are calculated with reference to global and principal coordinate systems. The background of the development of the program, its capabilities, and its special features, as well as the input required, are described in this report. Sample output is also shown in appendix C. Difficulties associated with numerical calculations of principal stresses and directions are pointed out. Threshold values for detecting these problems are reported; these values may be changed by the user as desired. Several test problems were set up to verify the computer program and were successfully solved.

Jan 1, 1992

This report provides concepts for two automated longwall mining systems; one for operation in a 42 to 57-inch thick section of the Lower Kittanning coal seam, the other in a 57 to 72-inch thick section of the Pittsburgh seam. The Lower Kittanning concept uses a single-drum bidirectional shearer and 500-ton capacity 4-leg chocks and the Pittsburgh concept uses a double-drum shearer with 500-ton shields. Each concept is designed to produce in excess of 2,500 tons of clean coal per shift with a 6-man face crew. The automated longwalls consist of off-the-shelf control system hardware attached to standard longwall equipment. Control hardware includes a control and display console; prime and backup mini-computers; multiplex data transmission, power, and control lines; several remote terminals which serve as interface junctions; and various sensors and actuators located on the longwall equipment. The system can be operated either fully automatically, remotely or manually.

Jan 1, 1976

By C A. Locke

Geophysical signatures of the Taranaki and Tongariro volcanoes reflect similarities in their age, composition and hydrothermal histories, but also reflect differences in host rock settings and edifice evolution. The Taranaki volcanoes have strong positive gravity anomalies showing that their edifices largely consist of dense andesite which reflects substantial lava production or dyke injection during construction and that large sub-edifice dyke/stock complexes occur. In contrast, the Tongariro volcanoes have strong negative gravity anomalies indicating low density edifices of volcaniclastic material; no sub-edifice intrusions can be identified, probably because of the lack of density contrast with host basement rocks. Strong positive magnetic anomalies over the younger cones can mainly be attributed to near-surface andesite lavas or dykes whereas subdued magnetic effects are associated with hydrothermally altered zones within both edifices and sub-edifice intrusions.  

Jan 1, 1995

By Higgins RJ

Environmental investigations have been undertaken by Ok Tedi Mining Limited (OTML) since 1981 when the Ok Tedi Environmental Study was commenced. Environmental monit- oring and management programmes were implemented in 1983. The programmes included water quality monitoring, river flow and sediment monitoring, surveillance of aquatic biological communities and a health and nutrition survey of the local people. These original programmes have continued, and additional programmes of work have been developed and revised to reflect changing operations and the need to focus investigations on specific areas and issues of concern. In April 1990, following the establishment by the Government of Papua New Guinea (PNG) of environmental management criteria for the Fly River system, compliance monitoring programs were introduced. Details of the compliance and additional monitoring programmes undertaken by OTML throughout the Ok Tedi and Fly catchments, including programmes of investigation in the Fly River estuary, Gulf of Papua and Torres Strait, are presented.

Jan 1, 1991

By L. C. Weiner

For zinc single crystals, xo = 3o, a surface coating raises both the cleavage and yield strengths over a large temperature range. The "brittle temperature," associated with slip after completion of twinning, does not coincide with the point of intersection of the flow and cleavage curves, which is associated with twinning. A surface film has no effect on the brittle temperature, while it lowers the intersection temperature some 20°. For crystals, yn = 83o, a coating decreases the cleavage strength, making it temperature independent, as well as increases the brittle temperature or its equivalent, the intersection temperature, 20°. These observations are described on the basis of a dislocation-pile-up-at-a-barrier model for brittle fracture; in crystals x,, = 3o the number and distribution of twins play a vital role. IN a recent investigation on the effects of solid environments on the brittle fracture of zinc single crystals,' it was demonstrated that the presence of a surface film changes the cleavage strength of these crystals, either increasing or decreasing it, depending on the crystal orientation. An increase in cleavage strength of some 43 per cent was found for coated crystals oriented x, — 3o K = 28",* while a decrease of 48 per cent was observed with crystals X" = y» — 83". Moreover, these effects were found

Jan 1, 1959

By Dyson N. F

Mixed cobalt-nickel sulphides precipitated from ammoniacal process liquors derived from nickel sulphide concentrates, mattes, and reduced nickeliferous laterites have been characterized.The mixed sulphides are prone to oxidation on standing and are rapidly leached under relatively mild conditions. The kinetics of the leaching reactions are controlled principally by temperature and oxygen partial pressure. Although the samples have different CO:Ni ratios and have undergone varying degrees of oxidation, there is little difference in their leaching behaviour. The results suggest that a single plant would be able to process mixed sulphides of varying composition. Any copper and zinc present in the mixed sulphides as impurities also go into solution and must be removed prior to recovery of the cobalt and nickel in metallic form.

Jan 1, 1981

Were it simply a matter of extracting tin from the simple tin sulphide, the proposition would undoubtedly be simple enough. When, however, other valuable metallic sulphides are combined with the tin, and it is required to separate these intomarketable products, then the proposition becomes somewhat complex, and such is the case with the class of material of which I am about to write. The locality where it occurs is Howell, New South Wales, and chiefly at the Conrad Silver-Lead Mine. The tin sulphide occurs chemically alloyed with copper, iron and other metals associated with galena, pyrites, mispickel, blende and silver sulphide in varying proportions, and generally in a gangue of highly crystallised quartz.Several varieties of tin sulphides occur, and from the following analyses of three minerals, these being specimens specially selected free from foreign matters, it will be seen that the chemical composition is somewhat complex.

Jan 1, 1902

By J. D. Noll

Elemental carbon (EC) is used as a surrogate for regulating the exposure to diesel particulate matter (DPM) of underground metal/non-metal miners. EC was chosen as a surrogate because EC is selective to DPM and is a major component of DPM. Using EC as a surrogate also gives one the advantages of no sampling artifacts and being able to sample at all locations in the mine. Currently, EC represents DPM well in underground mines. Some control technologies have been shown to possibly alter the relationship between DPM and EC and characteristics of DPM. Therefore, future work will investigate the relationship between DPM and EC as new control technologies are implemented.

Jan 1, 2002

The papers contained herein summarize results of various recent Bureau of Mines investigations in the area of mine power distribution systems. They are based on information from Bureau personnel, contractors and grantees, and Mining Enforcement and Safety Administration. Conclusions drawn from a series of parameter measurements on mine power systems, taken over a 3-year span, are presented. Personnel and equipment hazards due to faults on isolated, solidly grounded, and resistance grounded three-phase systems are discussed. Two papers cover dc applications of circuit breakers, including a novel protection scheme for trolley lines. The methods of suppressing induced arcing currents and voltages in a-c machines are evaluated. An evaluation program for ground monitors is described. Acceptance test procedures and the importance of various paparameters for trailing cable splice are covered. A number of techniques for locating faults in trailing cables are described.

Jan 1, 1975

By Alexandre Silva Guimarães

O presente trabalho avaliou o comportamento de extração dos metais cálcio, magnésio e níquel, contidos em licores sintéticos sulfúricos, utilizando-se o extratante Cyanex 272 (0,64 mol/L) e misturas entre Cyanex 272 (0,64 mol/L) e ácido versático (0,53 mol/L). Os resultados revelaram que a adição de ácido versático ao Cyanex 272 provocou um aumento nas extrações de cálcio, que atingiram cerca de 40% em pH = 5,1, decrescendo com a elevação do pH do licor até atingir aproximadamente em 15% pH = 5,9. As extrações de níquel (em torno de 80% em pH = 7,1) foram favorecidas, enquanto as extrações de magnésio permaneceram em torno de 75-80%, numa faixa de pH entre 6,0 e 7,0, em comparação com a utilização de apenas Cyanex 272 como extratante. O níquel pode ser separado dos metais cálcio e magnésio, pela mistura dos extratantes nas concentrações estudadas, em pH = 5,1, utilizando-se de 2 a 3 estágios de contactação.

Aug 7, 2018

By Robert J. Dompe

The objective of this program was to develop a cost effective microprocessor-based electronic image sensor system for monitoring pit slope displacement to detect and/ or predict impending slope failure in surface mines. A background study and data analysis yielded a performance specification for candidate Video Slope Monitoring Systems. A design concept was developed based on using a pair of solid state video cameras located on precision pointing assemblies. The digital images from the cameras are compared and, using electronic triangulation, slope topology is calculated. The current and past locations of operator selected features are compared to determine pit slope displacement. A proof-of-concept test was performed using a laboratory model of a pit slope. Based on the successful results of that testing it is recommended that an in-mine evaluation be performed using a full-scale prototype Video Slope Monitoring System.

Jan 1, 1982

By R. Jackman, D. Koningen, G. Wilcox

"Gowest Gold Ltd. is in the process of developing the Frankfield East gold deposit located along the largely undeveloped Pipestone fault northeast of Timmins, Ontario. In addition to resource development and environmental permitting work the company has had an ongoing program of metallurgical and engineering studies aimed at evaluating options for processing the Frankfield East ore. Mineralization at the Frankfield project contains arsenopyrite and pyrite as the major sulphide minerals. Bulk flotation of all sulphides results in extremely high gold recovery. However, the gold is almost entirely associated with the arsenopyrite fraction of the ore and is refractory in nature requiring preoxidation treatment. Selective flotation was investigated to recover a gold-arsenopyrite concentrate thereby reducing the mass which would be subjected to further gold processing. As part of this work, a pyrite concentrate low in arsenic content was also recovered that would be suitable as a source of sulphur for a smelter (or other pyrometallurgical facility). Production of separate arsenopyrite and pyrite concentrates is frequently examined but rarely adopted due to the distribution of gold between the two products or the inability to achieve adequate separation. Several flowsheet options were investigated in the study. The best results were achieved following a sequential flotation flowsheet. The flowsheet configuration was key to meeting the targets for the two products. In this paper, the various options investigated are reviewed and the results of the final flowsheet are presented. The overall plan by Gowest was to evaluate all process options to bring the Frankfield East deposit into production. The ability to effectively separate the arsenopyrite and pyrite components in the ore provides Gowest with added opportunities to pursue both short and long term production scenarios."

Jan 1, 2012

FREQUENTLY the Survey Department is caIled upon to estimate the quantity of material in various dumps, dams piles, etc... and in the carrying out of this work various methods may be employed.The method used will vary according to the particular case in hand, and factors such as accessibility of the top of the dump, steepness of its sides, height, and the condition of the material to be estimated. A certain amount of "give and take" must be adopted in the treatment of small local cavities and mounds.In all cases it is desirable that the surveys made should be tied on to the lease surveys for the purpose of location, and that all levels should be reduced to the mine datum. It is also desirable to obtain levels of the original surface before deposition of the material to be estimated. If these have not been obtained beforehand, levels and transfers round the top will be the next best. If space is availabIe, flat surface is chosen as a site for the dump, etc. This is of the utmost importance in those cases where the material will have to be...

Jan 1, 1925

By D. D. Bush

Based on the results of this study, the underhand cut and fill stoping method, with mass destressing, is an effective method for controlling rock bursts and falls of ground for deep mining in the Coeur d'Alene Mining District. The procedure can be utilized to pull highly stressed pillars by converting from conventional overhand stoping methods or used as a primary recovery system. During the demonstration, only one minor rock burst occurred, with no injuries. The system facilitates accurate placement of vertical boreholes for effective mass destressing. Each mining cut is filled with cemented sandfill overlying a timbered mat that forms the back for the succeeding cut. For this demonstration, a cemented fill was mixed on the surface and piped to the stone. Costs for pillar recovery by this method are comparable and are considered cost effective over conventionally timbered overhand mining as a pillar recovery method.

Jan 1, 1982

By Ihsan Berk Tulu, Mark Van Dyke, Ted Klemetti, Deniz Tuncay

"Longwall abutment loads are influenced by several factors, including depth of cover, pillar sizes, panel dimensions, geological setting, mining height, proximity to gob, intersection type, and size of the gob. How does proximity to the gob affect pillar loading and entry condition? Does the gob influence depend on whether the abutment load is a forward, side, or rear loading? Do non-typical bleeder entry systems follow the traditional front and side abutment loading and extent concepts? If not, will an improved understanding of the combined abutment extent warrant a change in pillar design or standing support in bleeder entries?This paper details observations made in the non-typical bleeder entries of a moderate depth longwall panel; specifically, it explores data collected from borehole pressure cells and roof extensometers, observations of the conditions of the entries, and numerical modeling of the bleeder entries during longwall extraction. The primary focus was the extent and magnitude of the abutment loading experienced due to the extraction of the longwall panels. Due to the layout of the longwall panels and bleeder entries, the borehole pressure cells (BPCs) and roof extensometers did not show much change due to the advancing of the first longwall. However, they did show a noticeable increase due to the second longwall advancement, a maximum of about 4 MPa of pressure increase and 5 mm of roof deformation. The observations of the conditions showed little to no change from before the first longwall panel extraction began to when the second longwall panel had been advanced more than 915 meters. Localized pillar spalling was observed on the corners of the pillars closest to the longwall gob as was an increase in water in the entries. In addition to the observations and instrumentation, numerical modeling was performed to validate modeling procedures against the monitoring results and evaluate the bleeder design. ITASCA Consulting Group’s FLAC3D numerical modeling software was used to evaluate the bleeder entries. The results of the models indicated only a minor increase in load during the extraction of the longwall panels. These models showed a much greater increase in stress due to the development of the gateroad and bleeder entries—about 80% development and 20% longwall extraction. The FLAC3D model showed very good correlation between modeled and expected gateroad loading during panel extraction. The front and side abutment extent modeled was very similar to observations from this and previous panels."

Jan 1, 2019

By M I. Pownceby, W J. Bruckard

A South African chromite sample was subjected to characterisation and physical beneficiation testwork in order to assess its suitability to produce an upgraded chromite product with a silica level of <1 per cent SiO2 and a chromite level of >46 per cent Cr2O3. Chemical analysis by XRF indicated that the bulk material had a Cr2O3 content of 40.5 per cent w/w and a SiO2 content of 7.5 per cent w/w. Combined XRF analysis with sizing data showed that the majority (~70 per cent) of the siliceous material was present in the +600 ¦m fraction while ~70 per cent of the Cr2O3 was in the -600 ¦m fraction. Qualitative mineral phase analysis by XRD indicated that the sample mineralogy was dominated by ferrian-magnesiochromite spinel ([Fe,Mg]Cr2O4) and aluminium-chromite spinel (Fe[Al,Cr]2O4), with enstatite (Mg2Si2O6), haematite (Fe2O3) and anorthite (CaAl2Si2O8) as minor phases. SEM and EMP characterisation showed that the silica was mainly present in discrete enstatite grains but lesser amounts were also present as the high silica phases plagioclase and enstatite on the edge of grains. Wet gravity separation performed on sized fractions (-600+106 ¦m size range) from the -2.0 mm (primary) ore as well as the ore that had been crushed to pass 0.6 mm (secondary) showed that stage crushing of the -2 mm +600 ¦m fraction followed by wet gravity separation upgraded the Cr2O3 grade at 70 per cent Cr2O3 recovery from ~44 per cent Cr2O3 in the primary material to 46 per cent Cr2O3 (the target grade specification) in the secondary sample. It also showed that the stage crushing of this +600 ¦m fraction at a cut-off level of one per cent SiO2 increased the cumulative Cr2O3 recovery from ~50 per cent in the primary material to ~63 per cent in the secondary sample in the same size range of -600+106 ¦m. The extent to which additional crushing could lead to improved chromite recoveries at the required chromite and silica grade target specifications was not determined. This experience demonstrates that prior to processing test work being conducted, a thorough understanding of the chemistry and mineralogy of the test sample promotes efficient and targeted processing research.

Jan 1, 2008

By Teele Tuuna, Voglers Eesti OÜ

Blasting operations are a strong and important part in any kind of building and mining industry, a shot-firer profession is one of the oldest professions in the civilized world. It still serves an important and ongoing purpose in the modern economy all over the world. Europe, nowadays, values strongly the mobility of workers, the movement of know-how and labor force between different countries inside Europe. There are no borders for most of the everyday professions.

Jan 1, 2018