Search Documents

By Peter A. Rona

The Mid-Atlantic Ridge in the central North Atlantic and the Gorda Ridge within the U.S. Exclusive Economic Zone off northern California and southern Oregon are yielding new discoveries of seafloor hydrothermal mineralization. The TAG hydrothermal field in the rift valley of the Mid-Atlantic Ridge near 26 degree N, 45 degree W has been a site of international collaborative research since the discovery there of extensive manganese deposits associated with low temperature hydrothermal activity in 1973 as part of the TAG (Trans-Atlantic Geotraverse Project). The first high-temperature hydrothermal activity, massive sulfide deposits and vent biota discovered in the Atlantic were found at the TAG hydrothermal field in 1985. Collaborative dive series with DSV ALVIN in 1990 and in 1991 with the two Russian MIR submersibles in the TAG field have found and sampled large inactive sulfide mounds in addition to the previously known active sulfide mound. The active sulfide mound on the floor of the rift valley is about 250 m in diameter and 40 m high with a concentric zonation of mineral types and flow regimes decreasing in temperature from 365 degree C black smokers at the center to white smokers and diffuse flow toward the margins. The recent dive series in coordination deep-towed instrument surveys have delineated a zone extending about 5 km along the lower east wall of the rift valley of inactive sulfide mounds up to a kilometer in diameter. MIR Mound in this zone consists of a central sulfide zone about 400 m in diameter and 50 m high surrounded by a halo of low-temperature deposits to 200 m wide. Inactive sulfide chimneys contain the first primary, free gold grains found at a hydrothermal site on a mid-ocean ridge (P.A. Rona, Y.A. Bogdanov, E.G. Gurvich, N.A. Rimski-Korsakov, A.M. Sagalevitch and M. D. Hannington, 199 1 EOS, Transactions, American Geophysical Union, 72:470-471 and Journal of Geophysical Research, submitted).

Jan 1, 1992

By Richard D. Begley

This paper summarizes the development of a mechanistic model to predict longwall mining induced surface subsidence. The model was originally developed from data acquired from a recent field study conducted in Northern West Virginia. Additional data has been collected from published sources and used to refine the model. The original model utilizes a negative exponential equation to predict the subsidence profile after the maximum possible subsidence is predicted based on the following input parameters: mine geometry, angle of draw and expansion factors for the deformation zones that have been identified above a longwall excavation. The model refinement involved the development of relationships between physical properties of the overburden strata and angle of draw in addition to the expansion or bulking factors. Therefore the refined model now requires only mine geometry and a typical geologic column from the site to predict the subsidence profile. This paper provides the methodology that enables the model to determine the angle of draw and expansion factors breed on physical properties of the site geology i. e. percent of strong rock and Rock Quality Designation of the overburden strata. In addition :comparisons of predicted results with measured data for over H) different sites with various geological and geometrical parameters located throughout the United States will be presented.

Jan 1, 1989

This report has been prepared in response to a request by the Bureau of Land Management (BLM) Fairbanks Alaska District Office that the Bureau of Mines quantitatively assess the potential supply of minerals from undiscovered deposits in the White Mountains National Recreation Area (WMNRA) and the western part of the North Steese National Conservation Area (SNCA) in Alaska. The assessment will be used to assist in future land-use decision-making. Resource Management Plans (RMPs) for the WMNRA and the SNCA were approved by the BLM in 1986. These plans imposed significant restrictions on new mineral development in the two areas. The level of public concern regarding these actions, especially on the part of the mining industry, has spurred BLM to seek additional information about the potential supply of minerals from the two areas with assistance from the Bureau of Mines. The assessment focuses on an area within the WMNRA and the SNCA which has been administratively closed to mineral entry. The study area encompassed approximately 1.24 million acres and included all of the WMNRA and the western portion of the North SNCA (fig. ES-1). Three quantitative estimates of the potential supply of minerals from the study area were developed: 1) For all lands in the study area, assuming that they are open to mineral entry-the baseline analysis; 2) For those lands which have been closed to mineral entry; and 3) For eleven prospective mineral activity areas, assuming that all are open to mineral entry.

Jan 1, 1989

By C. W. Morris

This Final Report describes the major technical activities that were accomplished to produce a comprehensive continuous miner training system (CMTS) for coal industry utilization. The primary product of this program was a continuous miner part-task trainer. It is composed of an interactive computer graphics system combined with the operating controls of a continuous mining machine mounted in a simulated cab. The cab contains an audio system for reproducing continuous miner operational sounds. The trainer is supplemented with a complete set of cognitive materials that provide instruction in the operation, safety and health of continuous miner operations. A complete summary of the field test and evaluation of the CMTS is provided along with a set of recommendations for further training program refinements, expansions, and utilization.

Jan 1, 1982

By Randolph R. Dreher, Michael L. Schreder

"In recent years, FFE Minerals has designed, installed and commissioned several large grinding mill circuits. This paper discusses the issues related to the erection and commissioning of large grinding mill circuits. The three circuits discussed are Collahuasi in Chile, Minera Los Pelambres in Chile, and Century Zinc in Australia. These circuits include large SAG and ball mills with both gear and gearless drive arrangements, as well as, both trunnion and shell supported mills. Aspects of these features are discussed with respect to their impact on installation and commissioning. While the normal challenges of mill erection and start-up were experienced, there were also a few unexpected challenges encountered partly due to the large scale of the equipment. An overview of the equipment and design ratings of these circuits is also provided.COLLAHUASIOverviewThe Collahuasi mills were started-up in November of 1998. The site is located in the Andes Mountains at an elevation of 4300 meters. The grinding circuit includes two lines featuring one SAG mill and one ball mill for each line. The circuit features a recycle conveyor around the SAG mills with provision for adding a pebble crusher in the future. The design tonnage of the grinding plant is 60,000 MTPD with an ore BWI of 10.5 kWh/MT.The SAG mills are 32’ x 15’ (1 3’ EGL) with 10,800 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The mills are driven by low speed synchronous motors with CCV variable speed drives. The SAG mills are trunnion supported and use hydrostatic lubrication. Feed to the SAG mills is via a rock-box type feed chute on a cart. The mills discharge on to trommel screens with a bucket wheel to remove the oversize.The ball mills are 22’ x 36.5’ (36’ EGL) with 12,500 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The fixed speed mills are driven by low speed synchronous motors with GE Quadramatic load sharing drives. The ball mills are shell-supported and feature multi-pad bearings with hydrodynamic lubrication. The mills are fed via a rubber lined sump box with feed spout on a cart. The ball mills also discharge on to trommel screens. Twenty-six inch (26”) diameter hydrocyclones are in closed circuit with the ball mills."

Jan 1, 2001

By Todd M. Ruff

Researchers at the National Institute for Occupational Safety and Health are investigating technologies that could be used to detect objects, small vehicles, and pedestrian workers that may be in the blind areas of haulage equipment used in mining and construction. A detection system that warns the equipment operator that there is an obstacle nearby could prevent collisions and save many lives each year. One popular technology for collision warning systems is radar. Several different types of radar have been tested in the laboratory and on mining equipment. Early in the study, questions arose concerning the best way to test radar systems. Many factors affect the performance of radar, including the size, shape, and composition of the object that is to be detected; the height of the radar antenna(s); and the relative motion of the radar system and/or object. This report discusses several different test procedures and test targets and recommends methods to determine how effective a radar system will be in detecting a person near heavy equipment.

Jan 1, 2002

By J. D. Steenkamp

"In July of 2016 and June 2017, major tap-hole repairs were carried out during the annual shutdown of two 63 MVA submerged arc furnaces producing ferrochromium in South Africa. The hot excavations of the tap-holes allowed for a study of the wear profiles. Subsequent thermodynamic calculations allowed for the quantification of the potential for chemical reaction between refractory and slag or alloy contributing to wear in the tap-hole area. Results from both wear profiling and thermodynamic calculations are reported here. IntroductionFerrochrome (FeCr) is an essential alloy in the production of stainless steel (Gasik, 2013). In 2017, 11.7 Mt of FeCr was produced (Pariser et al., 2018.). The main producers were China (39%), South Africa (29%), Kazakstan (12%), and India (8%).A number of grades of FeCr are available to producers of stainless steel, including high-carbon ferrochrome (HCFeCr) (Gasik, 2013). HCFeCr typically contains 60–70% Cr and 4–6% C (Basson and Daavittila, 2013). When the chromium content is lower (50–55% Cr) and the carbon content higher (6–8% C), it is referred to as charge chrome. Charge chrome is typically produced in South Africa due to the grades of ore available.FeCr is produced in submerged arc furnaces (SAFs) and in open arc furnaces (Mc Dougall, 2013) by carbothermic reduction of oxide raw materials. In a SAF the electrode tips are submerged in a porous charge mix. In FeCr production, the electrical energy is mainly liberated by resistive heating of the wet coke bed (Barker et al., 2007; Steenkamp et al., 2017). Thermally conductive lining design philosophies are typically applied in SAFs producing FeCr (Steenkamp, Denton, and Hayman, 2017; Coetzee, Duncanson, and Sylven, 2010; Coetzee et al., 2010).In July of 2016 and June of 2017, major tap-hole repairs were carried out during the annual shutdown of two 63 MVA SAFs producing FeCr in South Africa. The hot excavations of the tap-holes allowed for a study of the wear profiles. Both SAFs were operated on the same site, by two different operating crews, using the same raw materials. The major difference between them was that the SAF excavated in 2016 was an open SAF (referred to as Furnace A) and the one excavated in 2017 was a closed SAF (referred to as Furnace B). In an open SAF, a gap exists between the top of the steel shell and the roof, with the top of the burden being open to the atmosphere and the CO-rich off-gas being combusted as it escapes. In a closed SAF, the roof is attached to the steel shell and the CO-rich off-gas is collected from an offtake on the roof for further treatment and used in downstream processes.The paper presented here reports the macro-scale observations on refractory wear for the two SAFs, and studies the potential for chemical wear of refractory by slag and alloy as a potential contributing factor to the tap-hole wear observed."

Jun 1, 2019

In the plumbing of vertical shafts the methods employed and equipment used, are generally made to best suit existing conditions. Undoubtedly, there is no method that can be called standard or that can be used with equal ease and success on all shafts. At the Mount Isa Mines Limited property in Northern Queensland, Australia, local conditions have presented no major difficulties to be overcome in shaft plumbing work. In fact, compared to those at many shafts, the problem has been rather simple. There are three vertical shafts connecting main mine workings, with the greatest plumbing depth for any single lift, 350 ft.Other conditions pertaining to plumbing work have been generally normal.The method we have employed is, in principle, similar to the Weisbach orientation method with a variation that does not necessitate damping of the wires to bring them to rest. Although conditions encountered have not been such that damping the wires would have been inconvenient, we feel we have saved much time and eliminated unnecessary...

Jan 1, 1940

The panic bars (and associated linkage's and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on Self-propelled, electric and diesel face equipment; including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that are recommended in this document, but all of the panic bars are characteristically of the "fire door" type that is frequently encountered on outside exit doors of many public and soma commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes are added to the face equipment machinery for which they are required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in 'Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel at the various machine manufacturers and underground coal mines that we surveyed, discussions with G. L. Judy (our consultant), etc:

Jan 1, 1974

By H. J. Garcia

Biodegradation of cyanide by microorganisms isolated from solids previously exposed to cyanide has been investigated. Initial sodium cyanide concentration was 300 ppm at pH 10.5. The kinetics of biodegradation were found to be first order with respect to cyanide concentration, and the overall reaction rate constant is k = 0.102 day-1. The activation energy and the frequency factor were determined to be { A }Ea = 5.45 Kcal/mol and A = 1.28 x 10-2 sec-1, respectively. Based on these values, thermodynamic properties of an intermediate activated complex were assessed. All tests resulted in cyanide concentrations less than 0.1 ppm in about 35 days at 250C, whereas at 350C the time of biodegradation to reach this cyanide level was 30 days. Kinetic data were also established to relate biodegradation to amount of inoculum. The maximum theoretically-attainable rate, Vm , and the optimum amount of inoculum, K , were determined to be 4.8 x 10-4 M NaCN/day and 7.5 % of amount of inoculum. With respect to the mechanism of biodegradation, cyanide was shown to decompose to carbonate, bicarbonate and ammonia. Titrimetric analyses revealed concentrations of 5.6 x 10-3, 4.8 x 10-3 M, and 70.2 ppm for carbonate, bicarbonate and ammonia, respectively. The average cell population was determined to be 3.75 x 108 cells/mL.

Jan 1, 1994

By S. L. Chen

Keywords: copper, concentrate drying, steam dryer, dryers By placing additional demands on energy and gas flow, the moisture content of a copper concentrate has an adverse effect on the smelting process. Different drying technologies, such as directly heated rotary dryers, flash dryers, and steam dryers, are available to solve this problem. The energy requirements of and off-gas generated from different dryer types are compared. The performance of the steam dryer was found to be superior to that of the others. In particular, the rotary steam dryer and its benefits are discussed. Structural properties confer an advantage on the rotary steam dryer, for wear on tube elements is eliminated, and drying efficiency is improved. If steam is available, the rotary steam dryer is an excellent choice for drying copper concentrates.

Jan 1, 2006

By John J. Sammarco

The U.S. Bureau of Mines has developed a regulated, intrinsically safe, rechargeable power supply for portable electronic equipment for underground use. The regulated output is ideal for microprocessor power requirements and is suited for operation in hazardous environments. Two rechargeable, sealed batteries are contained within the power supply. Provisions are made to use an external source of power if these batteries fail. Provisions are also made to charge these internal batteries when needed. The circuit is composed of three main circuits: the main regulator circuit, the input protection circuit, and the output protection circuit. The main regulator circuit provides remote voltage sensing, current sensing, fault monitoring, and internal thermal protection. The input protection circuit checks for excessive input current and low battery conditions. The output protection circuit contains two overvoltage detection devices. Schematics, a parts list, and a calibration procedure are provided in this report to enable readers to fabricate the power supply.

Jan 1, 1989

The Australian Gas Light. Company was established in 1837, the first gas being sent out from the Kent Street Works, then the headquarters, in 1841. Mortlake Works were opened in 1886, and has since grown to the vast undertaking inspected by members of the Institute.The Kent Street Works were closed in 1921. The area of the, company's property at Mortlake is 117 acres.Some interesting figures from the statistics of the company's activities for 1937 are:-

Jan 1, 1938

By Gary L. Stecklein

This final report delineates the findings of the test programs, simulations, and analyses performed to determine the requirements for the effective application of berms and guardrails as truck restraint systems for elevated mine roadways. Included arts criterion for effective vehicle restraint for guardrail applications and recommendations for berm applications based on scale model tests and computer simulations. Full scale haulage vehicle-berm interaction field tests were performed to correlate the results of these model tests and computer simulations. Recommendations for the construction of berms were made on the basis of tests of berm bearing strength, response of the vehicle to different berms, and predictions based on the obtained correlation

Jan 1, 1981

By C. H. Fisher

Sulphuric acid of various concentrations has long been used as a reagent in the determination of olefins and aromatics in hydrocarbon oils4 such as gasoline, kerosene, and neutral oils from coal-tar distillates. Despite its long use, however, there is no general agreement as to optimum conditions and concentration of acid, and numerous methods and modifications have been recommended. In most cases, treatment of the neutral oil with 80 to 90 percent sulphuric acid, followed by distillation to the original endpoint to remove olefin polymers, is recommended for the estimation of unsaturated hydrocarbons. The distillate thus obtained is taken as olefin-free oil and used in later stages of the anlysis. Aromatic hydrocarbons generally are determined in the olefin-free oil by suphonation with more concentrated acid (96 to 100 percent and fuming sulphuric acid are recommended), the hydrocarbons not attacked and removed as water-soluble sulphoric acids being considered as saturated hydrocarbons. In some cases the saturates are examined further by differentiating between cyclic (naphthenes) and acyclic hydrocarbons (paraffins), Generally this is achieved by physical methods, although strong sulphuric acid is known to react preferentially with some types of saturated hydrocarbons. It was the purpose of the present work to make a general study of this type of analysis and to investigate the reactions of hydrocarbons under conditions often used in analyses that employ sulphuric acid reagents. Since previous work is not in good agreement, the optimum concentrations of acid for the different stages of the analysis were determined. Several sulphuric acid methods previously recommended and new modifications were compared, two synthetic solutions being used as the reference oil. The results obtained are presented below under separate headings.

Jan 1, 1937

By C. H. Fisher

Sulphuric acid of various concentrations has long been used as a reagent in the determination of olefins and aromatics in hydrocarbon oils4 such as gasoline, kerosene, and neutral oils from coal-tar distillates. Despite its long use, however, there is no general agreement as to optimum conditions and concentration of acid, and numerous methods and modifications have been recommended. In most cases, treatment of the neutral oil with 80 to 90 percent sulphuric acid, followed by distillation to the original endpoint to remove olefin polymers, is recommended for the estimation of unsaturated hydrocarbons. The distillate thus obtained is taken as olefin-free oil and used in later stages of the anlysis. Aromatic hydrocarbons generally are determined in the olefin-free oil by suphonation with more concentrated acid (96 to 100 percent and fuming sulphuric acid are recommended), the hydrocarbons not attacked and removed as water-soluble sulphonic acids being considered as saturated hydrocarbons. In some cases the saturates are examined further by differentiating between cyclic (naphthenes) and acyclic hydrocarbons (paraffins), Generally this is achieved by physical methods, although strong sulphuric acid is known to react preferentially with some types of saturated hydrocarbons. It was the purpose of the present work to make a general study of this type of analysis and to investigate the reactions of hydrocarbons under conditions often used in analyses that employ sulphuric acid reagents. Since previous work is not in good agreement, the optimum concentrations of acid for the different stages of the analysis were determined. Several sulphuric acid methods previously recommended and new modifications were compared, two synthetic solutions being used as the reference oil. The results obtained are presented below under separate headings.

Jan 1, 1937

By Zengjie Wang

Kinetic study of hydrochloric acid leaching of Panzhihua ilmenite from China is presented. Both temperature and concentration of hydrochloric acid have significant effects on the rate process of Fe dissolution from ilmenite ore, while the ratio of liquid to solid has little effect on the Fe dissolution. The Fe dissolution is found to follow the spherical model f (??) =1-(1- ??)1/3 and the apparent activation energy is calculated as 47.21 KJ/mol, suggesting a chemical reaction controlled mechanism. The dissolving behaviors vary at different kinetic stages. At the beginning the amount of the dissolved Fe and Ti increased monotonically with leaching time, while about 15 minutes later the dissolved Ti in the form of TiOCl2 began hydrolyzed into TiO2 fines reunited on the ilmenite ore surface, as observed by SEM and EDS technique. For the unreacted ilmenite particles covered by a layer of hydrolyzed TiO2, the leaching seemed to be as a selective leaching of iron and because Ti dissolved from and hydrolyzed rapidly again into the unreacted ilmenite particles. The leaching process can be ended 4 hour later when almost of Fe has dissolved into the solution and TiO2 remains as solid residues. The effects of acid concentration and leaching temperature were also investigated.

Jan 1, 2009

By Kira Mizell, James R. Hein, Tracy Conrad

"The Ninetyeast Ridge (NER) extends roughly N-S as a topographic feature for 5000 km, from 31° south to 10° north (Fig. 1) where it becomes buried beneath the Bengal Fan at its northern end. These two geographic characteristics make the NER an ideal natural laboratory for determining the influence of latitude and terrestrial input to ferromanganese (Fe-Mn) crust formation and composition. In addition to study of geographic controls on crust composition, the NER is the largest feature in the Indian Ocean that may host crusts of economic interest.Crusts were collected from 9 of 33 dredge sites from 1.4° north to 26° south latitudes during the 2007 R.V. Roger Revelle Knox06 cruise. Nineteen samples were analyzed for 69 elements each. Nine bulk crusts and 10 layers from four crusts were analyzed. Three of the crusts sub-sampled for layers did not have the bulk crust analyzed and the weighted means for those layers were calculated to obtain bulk compositions. One sample was left out of the statistical analyses because it is phosphatized and chemically quite different from the other samples (Table 1).In order to determine changes in composition with latitude, Pearson product-moment correlation coefficients were calculated for the chemical dataset and latitude of dredge sites, as well as water depth. At the 95-99% confidence level, the following elements increase in crusts moving north along the NER: Mg, Ti, S, Cd, Ni, Tl, Mn, Ba, Co, Cu, In, Li, and Zn; and the following elements decrease northward: Fe, Fe/Mn, P, As, Sc, the rare earth elements plus yttrium (REY), Bi, Ge, and Pb. These correlations indicate that the iron oxyhydroxide component and its associated elements are more prevalent to the south, and the manganese-oxide phase and associated elements increase toward the north end of the NER. This change occurs between dredges D20 and D14 (Fig. 1), with crusts from D20 and south having Fe/Mn !1.0 and those north of D20 ""1.2, with the exception of the phosphatized crust. Crust composition also changes with water depth: Th, Ge, Pb, and the middle rare earth elements (REEs) increase with increasing water depth. Thorium commonly increases in deeper water crusts, which explains the higher Th concentrations in Atlantic and Indian ocean crusts in general compared with Pacific crusts (Fig. 2 and Hein et al., 2012), including the samples analyzed here with a mean water depth of 3584 m. However, water depth does not explain the latitudinal changes because the mean water depths of samples along the northern and southern segments of the NER are roughly comparable. Surprisingly, Si and Al, representing the aluminosilicate/detrital phase, do not correlate with latitude; that is as the ridge approaches and is buried by the Bengal Fan the Si and Al contents do not increase. However, overall, Si and Al have higher concentrations in NER crusts than in central Pacific crusts. Ba can be used as a proxy for primary productivity and statistically does increase to the north along the ridge in the direction of the equatorial zone of high biological productivity. Correlations of Mg, Li, and Zn with latitude may also reflect increased primary productivity at lower latitudes."

Sep 1, 2014

By I. Alp

Application of magnetic separation was investigated for the enrichment of colemanite ores by removing the magnetic gangue fraction. The detailed XRD analysis of the ore has indicated that the gangue fraction is composed predominantly of the iron-bearing silicates such as smectite and, to a lesser extent, illite. Magnetic susceptibility measurements of the colemanite and gangue samples have proved that colemanite is diamagnetic in character whereas gangue fraction is weakly paramagnetic to allow the removal of this fraction by magnetic separation. Magnetic separation of the crushed and sized ore samples (-5 mm +75 µm) was performed using a high intensity permanent magnetic separator. Under the test conditions a colemanite concentrate (41.29 wt.% B2O3) was found to be produced from the crushed ore (30.76 wt.% B2O3) at a recovery of 96.76%. These findings suggest that magnetic separation has great potential as an alternative process for the production of a concentrate of commercially sufficient grade.

Jan 1, 2009

By D. Witchard, G. C. Penny

An important conclusion of the study is that altering the properties of the granulation water is a practical way of improving the sintering performance of blends that contain porous ores, and more work is under way to investigate other additives. Previous studies of iron ore blends containing pisolite ore showed that losses in sintering productivity were a result of deteriorating green-bed permeability. Pisolite ores are extremely porous and absorb a proportion of the water added during granulation. Although increased water addition could be used to counteract losses in productivity, the current study examined methods of inhibiting water absorption by pisolite ore as a means of improving productivity. Additives were used to alter the properties of the granulating water. With no increase in mix moisture contents pilot-scale sintering studies showed that sugar-based additives gave productivities that are higher than those obtained for a comparable ore blend containing haematite rather than the pisolitic ore. Several techniques of adding the sugar to the sinter mix were examined and found to increase productivity to varying degrees. Theoretical considerations, in some cases supported by experimental results, indicate that sugar-based additives not only inhibited water absorption by porous ore particles but also improved the permeability of the sintering bed. The study also suggested that, contrary to some commonly held views, the highly reactive nature of Yandi ore from Western Australia is beneficial for sintering. Porous ores enabled the formation of a strong sinter at fast flame-front speeds-both good strength and a short sintering time are requirements for high-productivity operation

Jun 18, 1905