Search Documents

The ventilation conditions at the underground coal mines are influenced; first: by the disturbances of the natural nature (barometric pressure, methane liberation, etc.), and second: by the disturbances caused by the production process. The major goal of this study was to determine the changes of the ventilation parameters, such as the flow, pressure and methane concentration around the longwall panel, particularly, along the longwall face due to the shearer operation (motion). It is well known from the practice, that the movement of the shearer influences the ventilation parameters around the longwall panel, including the gob area. Until now, these data were gathered in a single or multiple locations at the different time. However, only the simultaneous measurements of all of these values allow seeing the time dependent interrelationships between measured parameters. To be able to show these interrelationships, special experiments, described in this paper, were carried out by the author. These experiments were prepared and executed at the BUDRYK Coal Mine in Poland. During each experiment a simultaneous measurements and monitoring of the barometric pressure, air velocity and methane concentration at the different locations along the longwall face, were performed. The investigation was possible by using a special setup of instruments with a short sampling time, i.e., within 2 seconds. The monitoring of the absolute pressure was conducted by using the digital barometer µBar, developed by EMAG, based on the SETRA pressure transducer, model 470. The velocity of air was measured using the electronic vane-anemometers, developed by IMG-PAN. The methane concentrations were measured using methanometers as the part of the EMAG automatic gas monitoring system. The investigation data confirmed that disturbances due to the operation (motion) of the shearer at the longwall face have a local character. It could be also seen that a large diameter shearer (compared to the total cross-section area available for the air flow) is acting as the piston compressing the air (the overpressure) ahead of the shearer. This fact affects the methane mixing process and flow patterns in the vicinity.

Jan 1, 2009

By K. B. Lindsey

Geologically, the Williston Basin is a large structural depression of sedimentary rock in Montana, North Dakota, and South Dakota and Manitoba and Saskatchewan, Canada. The approximate It-mite of the basin are shown on figure 1; it is roughly circular with a diameter of about 400 miles and contains approximately 120,000 square miles. Although the petroleum potentialities in this area had long been recognized, it had not been vigorously prospected by the petroleum industry because of its geographic location, rigorous winters, depths to possibly productive zones, difficult geological problems, and the fact that more seemingly favorable areas were available for prospecting. With the discovery of oil near Edmonton, Alberta, in the prolific Devonian reefs, an incentive was given to explore for oil in the southeast extension of the same sedimentary trough, the Williston Basin. The Virden field discovery in southwestern Manitoba in January 1951 was a direct result of this southeastward movement. Discovery of this shallow field was followed soon after by discovery of' deep production on the Nesson anticline in North Dakota at Clarence Iverson No. 1 well. North Dakota then became the twenty-seventh petroleum-producing State.

Jan 1, 1954

By E. Morrice

The metallurgical laboratory data developed in this study indicate an improved electrowinning process for producing higher purity cerium ingot. A typical sample of the Reno electrocerium contains 99.9 weight-percent cerium and the following impurities: Total other rare-earth elements, less than 0.04 percent; iron not detected; silicon and aluminum, less than 0.02 percent each; calcium plus magnesium, less than 0.01 percent; carbon, 0.01 percent; oxygen, 0.002 percent; hydrogen, 0.0003 percent; and nitrogen, 0.0015 percent.

Jan 1, 1960

By Tarrant Elkington

Underground mine planning practices are typically manual and time consuming and will often produce sub-optimal solutions due to the application of generic rule-of-thumb assumptions or ?tried and tested? choices. The development of computer-automated tools for underground mine planning enable a wide range of scenarios to be considered rapidly in arriving at an optimised solution, subject to input assumptions. We have applied these tools to demonstrate ?optimised? solutions that challenge industry standard practices. Further, we have incorporated grade and price/cost uncertainty into these tools to gain an understanding on how the consideration of uncertainty may further alter strategy selection. Finally, we enable the tools to dynamically adjust cut-off grades in conjunction with the evolution of prices/cost.

May 1, 2010

Sulphide minerals, such as pyrite and sphalerite, are leached by ferric sulphate. This reaction produces ferrous sulphate and other dissolved products. The ferrous sulphate is re-oxidized to ferric sulphate by bacteria. These reactions can be written as: [ ] However, in 1964 Silverman and Ehrlich proposed that this is not the only role that is played by bacteria. These researchers proposed that T. ferrooxidans enhances the rate of oxidation of pyrite above that achieved by chemical reaction with ferric sulphate at the same solution conditions. This enhancement in the rate of dissolution was proposed to occur by direct microbiological action, possibly by the extra cellular secretion of an enzymatic oxidant. Since the Silverman and Ehrlich proposal, different authors have made opposing claims concerning the action of T. ferrooxidanson pyrite. This ?direct mechanism? of bacterial dissolution of pyrite can be given by the following reaction: [ ]

Jan 1, 2000

By Lance McAnuff

The year 2001 coincided with the forty-fifth year of blasting-control specialization by the author. Commencing with the construction of the Saint Lawrence Seaway System in 1956 and continuing until the present time this career has spanned one of the most progressive and exciting periods in the still relatively short history of commercial blasting. The paper touches upon a number of the more interesting projects with which the writer was involved during those early days, including the removal by explosives of “Ripple Rock” the infamous underwater hazard to shipping which at one time inhibited ocean traffic along the Inside Passage between Vancouver Island and the mainland of British Columbia, Canada’s most westerly province. Various assignments involving incidents from devastatingly ,tragic to comically absurd are described, along with personalities encountered along the away, most of them readily recognizable as giants in the field of explosives engineering. Various stages in the evolution of state-of-the-art explosive products, initiation systems vibration monitoring equipment and limiting criteria are compared and some of the effects these have had on safety and productivity during the last forty-five years are analyzed.

Jan 1, 2002

By Zsuzsanna Zborovszky

Study of different parameters (minimum discharge voltage, minimum discharge current, wire electrode diameter, speed of separation, electrode materials, overlap of the electrodes, etc.), their direct effect on the power going into the discharge, and their indirect effect on the possibility of obtaining ignition with an 8.31% methane-air mixture from a resistive circuit. Critical evaluation of the Cadmium disc breakflash (the presently internationally recommended test apparatus). Description of experimental setup and apparatus.

Jan 1, 1974

By Sam S. Taylor

Subsurface disposal of oil-field brines was practiced in Oklahoma on a limited scale as early as 1925. The technique of subsurface injection has been improved immensely and has been applied with varying success in many oil-producing areas in Oklahoma, and elsewhere. This method of disposal, however, is only one of several methods available to operators of oil-producing properties, but, in contrast with usual methods of handling brines on the surface it eliminates the damaging effect of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. Other methods of brine disposal approved by regulatory agencies in some States include (1) impounding in impervious ponds and solar evaporation, (2) controlled diversion into surface waters, and (3) recovery of the mineral salts of the brine. In most, States where oil is produced regulatory bodies authorize the use of one or more of these methods of brine disposal. In Oklahoma, for example, the Oklahoma Planning and Resources Board of the Conservation Commission has been authorized to adopt whatever methods or means may be necessary to prevent contamination by mineralization of all potable waters within the State.

Jan 1, 1942

By D. E. L. Zapata, O. J. R. Baena

"INTRODUCTION Mining is a fundamental part of the historical and economic development of a country. In Colombia, this is reflected from pre-Columbian jewelery, to being now one of the first exporters of coal worldwide, in 2017, the Colombian mining sector contributed approximately 6% of GDP (Ministerio de Minas y Energía, 2017). Coal, nickel, gold, platinum, emeralds, limestone, salt, phosphate rock, clays, siliceous sands and to a lesser extent copper, manganese, magnesite, barite, gypsum and various types of ornamental rocks, among others are produced (UPME, 2016). The contributions of mining activity in the economic dimension is more measurable, on the contrary in other dimensions, as the social and environmental, for this, every day there are new proposals and tools oriented to strengthen how to evaluate the contributions in terms of the sustainability and responsibility, with the aim of quantifying, concreting and non-utopian, to improve the life quality of a community and not only to comply with reporting and gaining prestige. Colombia has a generalized increase in the mining sector where the levels of informality and illegality are evident only 10% of mining activity is legal (UPME, 2014), also, the mining sector is accused of human rights violations, high levels of inequality, poverty and the affectation of ecosystems due to bad environmental management, among other situations (ACNUDH Colombia, 2015). This problem has generated rejection to the realization of the mining activity in many places of Colombia. At this point, it is important to clarify this problem is more complex, different actors are involved in this conflict, but it is an evidence that is needed a sustainability model for specific realities such as the Colombian mining. This situation in the current mining activity, is similar to the chemical industry situation three decades ago, because of an extensive problem in relation to repeated work accidents, natural disasters and indications as a highly polluting and unsustainable industry, with the aim of improving, not only this public perception, but also in the way of carrying out the business activity. Thus, in 1985, the Canadian Chemical Producers Association released the Responsible Care Program (RCP) (ICCA, 2015). Being aware that companies were responsible for the affected lives in some way by the operation and needed to improve workers safety, environmental protection and most importantly how legal persons should comply with the law, but go beyond this. RCP is most recognized sustainability initiative in the chemical sector, companies associated are recognized for having high quality standards, continuous improvement, visibility, corporate ethics, environmental and social management (ACC, 2015). In addition, to meeting the objectives is set out the creation of a model that increasing reputational sector levels. This initiative is considered to be a worldwide successful case of reporting corporate responsibility indicators and contributions to sustainability from the industry sector to local development (BASF Group, 2016)."

Jan 1, 2018

By Woodcock J. T, Zhu T, Sparrow G. J

A lead-zinc-pyrite flotation middling was pressure oxidised to give residues containing iron hydroxy sulphates (a mixture of basic iron sulphate (BIS) and a hydrated iron sulphate (HIS)) and lead sulphate. Direct thiourea leaching of this residue gave over 90 per cent extraction of gold and silver, but thiourea consumption was high (56 kg/t) because of soluble iron(M) in the residue. Attempts were made to decrease the thiourea consumption by removing the water-soluble iron(M) or reducing it to iron(II). Water washing of the pressure oxidation residue removed most of the hydrated iron sulphate but little of the basic iron sulphate. Iron removal was only 12-20 per cent, depending on the number of washes, from one sample which was low in HIS, and 40-45 per cent in another which was high in HIS. Iron extraction was not appreciably increased by using dilute sulphuric acid (with or without additions of sodium sulphite), dilute phosphoric acid, or sodium chloride solution (150 g/L NaCI). Direct thiourea leaching of the water-washed residue gave over 90 per cent extraction of gold but only 49 per cent of silver, with a thiourea consumption of 27 kg/t. However, the application of a water wash followed by reduction of dissolved iron(III) with sodium sulphite in the presence of thiourea, and then thiourea leaching resulted in over 98 per cent extraction of gold and silver for a thiourea consumption of 26 kg/t.

Jan 1, 1991

By A. Sariisik

This study analyses the results of a pilot trial of a newly developed armed-chained stone-cutting machine. The machine was developed in Turkey and trialed at the Kaklik/Kocaba travertine quarries in the Denizli District. An armed-chained cutting machine is an alternative to the diamond wire cutting method more frequently used in the production of natural stone quarry blocks, and increases production efficiency and quality. Since there is no need to collapse the blocks using the armed-chained cutting production process, there is no risk of the block developing cracks. This results in a considerable increase in the efficiency of natural stone block production. The armed-chained cutting machine is easier both to assemble and run when compared to other block cutting methods. This process resulted in the production of a larger number of blocks at a lower cost within the same time frame, particularly in travertine quarries and in all other natural stone quarries. The block efficiency in travertine quarries was calculated as 65?80%using the armed-chained cutting machine, compared with 7?14% using the normal diamond wire cutting method.

Jan 1, 2010

By Ronald M. Hays

The Duluth Gabbro Complex in Northeastern Minnesota possibly contains a significant domestic copper resource and the nation's largest nickel resource. Exploration has discovered large low-grade copper-nickel (Cu-Ni) deposits between Hoyt Lakes and the Boundary Waters Canoe Area (BWCA). The mining and processing of Cu-Ni will have environmental, economic, and social impacts. The purpose of this study is to relate major environmental, economic, and social considerations to various aspects of Cu-Ni extraction. An open pit and two underground (block caving and open stoping with backfilling) models were developed to generate information on the impact of Cu-Ni extraction. Important considerations having environmental, economic, and social impacts (luring various aspects of Cu-Ni extraction are identified and defined. These aspects are exploration, development, mining, beneficiating, smelting, transportation, and termination of operations. Considerations are grouped into the general categories of site, industrial, energy, climatic, resource, water, air emission, waste disposal, employee, tax and royalty, transportation, and community considerations. Cu-Ni extraction in Northeastern Minnesota presents major environmental, economic, and social risks. Decisions are required on trade-offs between adverse and beneficial impacts. The approach used in this study assists in assessing environmental, economic, and social impacts. It will aid in the examination of potential and projected short-term and long-term advantages and disadvantages and will aid in the development of Minnesota's Cu-Ni resource for the maximum benefit to society.

Jan 1, 1974

By Leland E. Paulson

This investigation examined the feasibility of altering the inorganic component of North Dakota lignite by ion exchange. Lignite of specific size consist was washed with various ionic solutions and examined for evidence of exchange. Ions of higher valance substituted preferentially at equivalent concentrations. Results indicate that a major portion of the inorganic material associated with lignite is combined in exchangeable form with the organic component. Particle size of the treated coal is a critical factor in determining the rate of exchange. The data indicate that monovalent ions are easily replaced by divalent and trivalent ions, and the presence of ionic material in slurries containing finely divided lignite significantly increases filtration rates.

Jan 1, 1968

During the period 1979 thru 1982. Multi Mineral Corporation conducted a mining research program at the United StAtes Department of the Interior's Bureau vi Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and. the results are described in this report.

Jan 1, 1983

By J. L. Gregg, J. L.

RECENTLY there has been considerable interest in the production and use of extra hard alloys composed primarily of tungsten and carbon. Dr. Hoyt's recent paper1 gives a good description of these alloys and describes their performance when used as tools. There are a number of these alloys on the market sold under various trade names, and it is the purpose of this paper to describe the results of an investigation of the structure of five of these alloys by means of microscopic and X-ray methods. The samples studied were in the form of small tools or wire-drawing dies, which were either purchased or supplied as samples. They were in some cases not supplied by the original makers but were furnished by the agents in this country, and we wish to call attention to the fact that they may not be truly representative of the materials supplied under the various trade names. No performance data are given and no inference as to the inferiority of one alloy as against any other is made. K. Schröter2 recently described methods for polishing alloys of this type for microscopic examination and has presented photomicrographs of several alloys. However, he did not identify their constituents or describe methods for their identification.

Jan 1, 1929

By Nino Catalano

The combination of two top levels of cross-lot braces designed and installed to act as a truss, and vertical post-tensioning of the panels allow the unbraced excavation of a 36' span. Philosophy of Excavation Support System The excavation of interest is for the cut-and-cover box sections of the southern approach to the Third Harbor Tunnel, which is part of the Central Artery/Tunnel project in Boston, Massachusetts. The 60' deep excavation is located very close to an existing building which is supported by piles, as shown in Figure 1. Therefore, it was necessary to minimize ground movement which may damage the building.

Jan 1, 1994

It is predicted that vast volumes of affected mine water will be produced by mining activities in the Mpumalanga coalfields of South Africa. The potential environmental impact of this excess water is of great concern in a water-scarce country like South Africa. Research over a period of more than 10 years has shown that this water can be used successfully for the irrigation of a range of crops (Annandale et al., 2002)1. There is, however, continuing concern from the local regulators regarding the long-term impact that large-scale mine water irrigation may have on groundwater quality and quantity. Detailed research has been undertaken over the last three years to supplement the groundwater monitoring programme at five different pilot sites, on both virgin soils (greenfields) and in coalmining spoils. These sites range from sandy soils to very clayey soils. The research has included soil moisture measurements, collection of in situ soil moisture over time, long-term laboratory studies of the leaching and attenuation properties of different soils and the impact of irrigation on acid rock drainage processes, and in depth determination of the hydraulic properties of the subsurface at each of these sites, including falling head tests, pumping tests and point dilution tests. This has been supported by geochemical modelling of these processes to quantify the impacts. The results indicate that many of the soils have considerable attenuation capacities and that in the period of irrigation, a large proportion of the salts have been contained in the upper portions of the unsaturated zones below each irrigation pivot. The volumes and quality of water leaching through to the aquifers have been quantified at each site. From this mixing ratios have been calculated in order to determine the effect of the irrigation water on the underlying aquifers. Keywords: coalmines, irrigation, gypsiferous mine water.

Jan 1, 2009

By Ross R

Although mining is an old industry its management is quite a new science, and its complications are now being recognised as demanding expert knowledge in many branches of technical and professional education. Not the least amongst these isaccountancy, for probably its most important problem is "How to control the expenditure." Unlike most businesses a mining company stands almost entirely in the light of a purchaser in the world's markets, and not as a seller, except say for product so the established and perfected systems of modern industries cannot be adopted for mining purposes. For this reason it has been left for late years to consider the matter seriously, and now a number of well-managed concerns have devised costs systems to suit their own requirements.Very little, however, has been published and even that is disjoined and difficult to make use of. Some of the costs systems in vogue, although elaborate and imposing, are not of very great value for keeping check on wasteful expenditure, or for displaying the commercial effect brought about 'by any particular change in practice, or by an addition or alteration to a portion of existing plant.

Jan 1, 1912

By M. Rahmanpour

"Mine planning is a multidisciplinary procedure that aims to guarantee the profitability of a mining operation in changing and uncertain conditions. Mine plans are normally classified as long-term, intermediate-term, and short-term plans, and many factors affect the preciseness of these plans and cause deviations in reaching the objectives. Commodity price is the heart of mine planning, but it has a changing and uncertain nature. Therefore, the determination of mine plans in the presence of uncertain mineral price is a challenge. A robust mine plan reduces the risk of early mine closure. A procedure is presented to determine the value at risk (VaR) in any possible mine planning alternative. VaR is considered together with downside risk and upside potential in order to select the most profitable and least risky plan. The model is tested on a small iron ore deposit. IntroductionMining projects are normally evaluated with the objective of maximizing economic value, as measured by the net present value (NPV). The aim of mine planning is to develop a yearly extraction plan that guides the mining operation to the highest NPV (Dagdelen, 2007; Yarmuch and Ortiz, 2011). This plan considers the technical constraints such as blending requirements, block sequencing, and pit slope (Caccetta and Hill 2003). Thus, the mine plan affects the economics and the payback period of mining operations.Mine planning is a procedure based on which the profitability of the mining operation is guaranteed in changing and uncertain conditions (McCarter, 1992). However, conventional mine planning ignores the volatility and uncertainty of future commodity prices and does not allow for managerial flexibility. It is common practice to assume a deterministic and constant commodity price through the mine life. The problem with this approach is that the commodity price is the heart of the mine planning procedure and governs the profitability and feasibility of the operation; thus ignoring price volatility will result in a sub-optimal mine plan."

Jan 1, 2016

This report is in partial fulfillment of Contract S0241051 awarded to COMINEC on June 27, 1974. 'Me purpose of the work under this contract is to develop a conceptual design for an automated longwall mining system. The conceptual design will serve as the basis for future design and development of an automated longwall mining system capable of sustained production in excess of 2,500 tons per shift with reduced manpower which will ultimately be demonstrated in an area where conventional longwall mining has been successful. 1.2 DEFINITION OF THE PROBLEM 1.2.1 Why An Automated System The most obvious benefit of automation and remote control in a longwall mining system is the reduction of accidents consequent upon a reduced working force in the hazardous face areas. However, another important aspect of the problem is the skilled labor shortage which is being compounded by the need for vastly increased coal production. The United States coal mining industry had a working force of almost 600,000 miners in 1928 but was able to muster only 145,000 miners in 1970. The miners required to staff the additional working sections and the new mines necessary to meet our energy needs are simply not available. Only automation and remote control will permit a reduced work force with increased production by keeping the face equipment operating continuously.

Jan 1, 1975