Search Documents

By Keith D. Rosbury

The basic objective of this project was to determine the cost-effectiveness of dust control used on unpaved mine haul roads. Field testing was conducted at three surface coal mines (two in Wyoming, one in southern Illinois) for a total of 20 weeks. The highest control efficiency measured for a chemical dust suppressant, 82 percent, was for calcium chloride two weeks after application. Generally, however, the control efficiencies hovered in the 40 to 60 percent range over the first two weeks since application, and then decreased with time. After the fifth week, the limited number of data points suggest a control efficiency of less than 20 percent. Composite watering data were fairly uniform. Watering once per hour resulted in a TSP control efficiency of approximately 40 percent. Doubling that application rate increased the control effectiveness by about 15 percent to 55 percent. Chemical dust suppressants (primarily salts and lignons) can be shown to be more cost-effective than watering under some conditions. Data summaries and the analysis of data are contained in Volume I. Volume II contains basic data.

Jan 1, 1983

By L Lachance, F Flament, D Leroux, S GariTpy

"Considerable metal values are often locked in stockpiles (ore, concentrates, heap leach pads, slags, reverts, etc.) and process equipment (bins, holding tanks, thickeners, etc.). This is more than enough to justify accurate accounting of such in-process metal inventories from both financial accounting and operational perspective. However, accurately determining the metal inventory of an in-process unit is often a challenge in industrial practice. Audits have shown that available indirect or direct measurements often carry large inaccuracies. Sooner or later, ignoring these measurement errors lead to unexpected incoherencies in reported metal balances. In such situations, coherent metal balances are then achieved through subjective and sometimes significant adjustments of in-process inventory levels. While such metal accounting methods applied by mineral processing engineers used to be rarely challenged, they are now being increasingly scrutinised by various stakeholders. Hence, metal accounting procedures that mitigate subjectivity in adjustments while still coping with the unavoidable uncertainty are more relevant than ever.This paper reviews three different metal accounting methods for reporting in-process metal inventory values. Their individual application strongly depends on the available measurements i.e. The indirect method where the metal inventory of a given process unit is determined by subtracting the cumulative reclaim from the cumulative feed carries important flaws. The direct method also comes with challenging accuracy issues so that emptying a process unit is often the best available inventory measurement. This reality is recognised for by further analysing a previously proposed operating mode where two interchangeable process units are alternately used. The third investigated method is the redundant method which combines indirect and direct methods for a given process unit. This paper reveals that the dual process unit operating mode and the redundant method can both significantly improve the estimation quality of in-process metal inventories.CITATION:Lachance, L, GariTpy, S, Leroux, D and Flament, F, 2013. Review of metal accounting methods for in-process metal inventories, in Proceedings MetPlant 2013, pp 102-117 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By L. F. Miao

Studies were carried out to investigate the ultimate soil pressure acting on pile(s) undergoing lateral soil movement in soft clay. A special apparatus has been designed to apply a uniform rectangular profile of lateral soil movement on the rigid pile(s) with pinned head and tip conditions to obtain the ultimate soil pressure. The piles were 16 mm (5/8 in) in diameter. For the pile group tests, the behavior of different number of piles (2, 3, 4, 6 and 9), pile arrangements and center-to-center spacings (3 and 6 diameters) were investigated. In this paper, the group factors of 11 combinations of number of piles, pile arrangements and pile spacings are presented. The group factors are given for individual piles in a pile group as well as for the entire group. Generally, the group factors of individual piles in a group varied significantly according to pile spacing in both directions, and pile arrangement; the group factor of the whole group reduced with an increasing number of piles, and increased with increasing pile spacing. For a pile group with the same number of piles but different pile arrangement, no significant difference was found in the group factors for the entire group.

Jan 1, 2008

Using mines in Canada, Boart Longyear, a leading provider of drilling services and products, has put its Stage 3 Coring Bit to the test and each time the bit has passed the test with great success. After more than a year in the field at a major mine operation in Sudbury, Canada, the Stage3 coring bit broke life records to become recognized as the most productive design in the industry. In addition to the proven advantage seen in regular bit life increases of as much as 300 percent in some cases, the design is quickly being recognized for its cost-saving operational impact. In Sudbury, the mine operation realized actual cash savings of more than C$45,000 within an eight-month period by making the switch to Stage3 bits. For years, the Sudbury Basin team has relied on the Alpha Extended Crown bit with the Express Waterway geometry option, ordering approximately 500 units per year. This 07 COM ECEX configuration performed well in medium-hard, non-abrasive to ultra-hard, non-abrasive formations with an average bit life of 150 m (490 ft). While satisfied with the performance of the Alpha Ex-tended Crown, the team agreed to put the new Alpha Stage3 to the test. Boart Longyear?s field engineers supplied five drill sites with Alpha Stage3 bits in a 07 COM configuration. After thoroughly testing the Stage3, the results were clear. Even with the well-known performance and versatility offered by the previously preferred configuration, the Stage3 set a new standard of bit performance. The new bit maintained its cutting edge for up to three times longer than the Alpha Extended Crown, a significant performance increase when compared to the 07 COM ECEX.

Jan 1, 2009

By Edwards A. B

Occasional, sporadic and small occurrences of lollingite in the Broken Hill lode have been described,(l) mostly in the garnet sandstone in the foot-wall and under-wall of the Broken Hill lode. The lollingite contains appreciable percentages of cobalt and nickel and is regarded as an early mineral in the development of the lode; and, with the incoming of the sulphides, it has suffered considerable replacement by arsenopyrite. During the conversion of iron arsenide into the iron sulpho-arsenide, ilie nickel and most of the cobalt are removed in solution and are inferred to reappear in niccolite and other minerals that have been recorded among the later minerals of the Broken Hill lode. As a result of observations of the officers of ilie Broken Hill South Ltd., an occurrence of cobaltite can now be recorded which has developed by an analogous type of replacement.Cobaltite has previously been recorded from the Australian Broken Hill Consols lode in the vicinity of the rich deposits of silver, though not in contact with them. Cobaltite has been found in the northern extremity of the No. 2 lens of the Broken Hill lode at the 1,480 feet level of the Broken Hill South...

Jan 1, 1944

The Subtropolis mine is a room-and-pillar mine extracting the Vanport Limestone near Petersburg, Ohio. In February 2018, mine management began implementing a heading reorientation to better control the negative effects of excessive levels of horizontal stress. The conditions in the headings improved, but as expected, stressrelated damage concentrated within crosscuts. The mine operator has worked to lessen the impact of the instabilities in the outby crosscuts by implementing several engineering controls. With the implementation of each control, conditions were monitored and analyzed using observational and measurement techniques including three-dimensional (3-D) LiDAR surveys.

Jan 7, 2020

By Jonathan S. Kelly

Effective control of respirable dust is one of the most serious problems associated with longwall mining in the United States. This report describes the development and the underground evaluation of ventilated cutting drums, on a double ended ranging drum shearer. The ventilated drum uses high pressure (1,500 psi) water sprays to draw air (3,500 cfm) through 12 airmoving tubes mounted in the drum hub. The sprays draw dusty air from the face side of the drum, scrub the air, and discharge the clean air on the gob side of the drum against a deflector plate. During a three week underground evaluation, the cutting drums reduced shearer generated dust levels at the shearer operators position by 40%, at the shield operators downwind of the shearer by 55%, and at the tailgate by 55%. Cutting and loading performance of the drums were superior to the mine?s conventional drums. After the evaluation, the mine continued to use the ventilated drums to finish mining the panel. During this 3 month period, there were no mechanical or seal failures demonstrating excellent system reliability.

Jan 1, 1987

By K. L. Bainbridge

This report describes the results of a study to determine which types of, and to what extent, mining wastes can contaminate groundwater through leaching of acid-forming or potentially toxic constituents. The primary focus of this study was on coal mining wastes, especially overburden spoils and preparation plant refuse. In addition, the potential for contamination by leachates from clean coal stockpiles was also examined. The study approach included investigation of (a) the amounts and geographic locations of mining wastes in the United States; (b) the chemical character of mining wastes, especially with regard to potentially acid-firming or toxic constituents; and (c) the extent to which acid and/or toxic components are leached from mining wastes by rainwater. To evaluate the leachability of coal wastes, a laboratory waste leaching method was developed during this study to specifically simulate the leaching process over a long-term. Waste samples collected during this study were also leached by the EPA extraction procedure and ASTM waste leaching method. Results of the three leach test methods were compared to evaluate their relative capabilities to predict the leachability of mining wastes.

Jan 1, 1980

By Carroll Forbes

INTRODUCTION MANY different shapes of drill bits are in use with hammer drills, but little definite information is available whereby to judge which one of these shapes is the best. The following investigation was undertaken in order to determine what effect, if any, the shape of the cutting edge has on the cutting speed and wearing qualities of drill bits. The bits tested were those in common use, namely, the 4-point or cross bit, the 6-point bit, the Z bit and the "Carr" bit. The rock in which the tests were made was the red granite from southeast Missouri. It is a coarse crystalline granite containing an unusually large amount of quartz and is extremely hard, and on account of its uniform texture is admirably adapted to this work. While tests in other rocks might show somewhat different results, nevertheless it is the opinion of the authors that the relative cutting quality inherent in the shape of the bits would be the same in all rocks. Other qualities, such as mudding freely, freedom from fitchering, etc., might make one bit more desirable than another in softer rocks. DESCRIPTION OF BITS TESTED The 4-point bits were the usual shaped bits commonly made on the Leyner sharpener with 14° taper on the wings and a 90° angle between cutting edges. Some tests were run at 85 lb. pressure with a 4-point bit made with a 5° taper on the wings. This was made by using the Carr bit die. The 6-point bits were the usual shaped hits made on, the Leyner sharpener. The Carr bits were made with a 5° taper and an angle of 100° between cutting edges.

Jan 8, 1917

By Cadia Geology Team

The Cadia Hill Gold Mine, located near Orange in Central Western New South Wales, is owned and operated by Cadia Holdings Pty Ltd, a wholly owned subsidiary of Newcrest Mining Limited. Construction including pre-strip mining occurred from 1996 to 1998. The mine was officially opened in October 1998 following commissioning of the concentrator and mine fleet in June of that year. The Cadia Hill orebody is a porphyry related gold and copper system. The final pit has a strip ratio of approximately 1.3:1.0. Mining is undertaken on 15 metre benches using large capacity diesel hydraulic face shovels at an annualised rate of up to 70 Mtpa. The concentrator is currently rated at 17Mtpa and includes the worldÆs largest single line grinding circuit. The feasibility Mineral Resource was estimated at 352 Mt at 0.63 g/t Au and 0.17 per cent Cu. Initial reserves totalled 200 Mt at 0.74 g/t Au and 0.17 per cent Cu yielding a mine life of approximately 12 years. During the pre-production period mine geology systems were developed to support the operation. By design these systems were intended to add value to the business through minimisation of material miss-classification, provision of accurate and timely production information and mapping and reconciliation as a continuous model improvement tool. Variances that would prove to be material to the life of mine plan were recognised during the first year of production. These included identification of additional ore tonnes, higher copper grades and higher gold recoveries relative to the model. Gold grades and copper recoveries also reconciled favourably. Testwork was undertaken to determine the underlying causes of each variance. Re-modelling was then undertaken to capitalise on those variances. The Cadia Hill Gold Mine life of mine plan was re-evaluated with updated geology, grade, geotechnical, metallurgical and environmental inputs. Operating strategies were also reviewed and revised. Despite application of reduced metal prices in the evaluation, the outcome was one of extended mine life with more metal produced at lower cost. Development of robust mine geology systems, including a pro-active reconciliation process contributed to tangible improvement of the Cadia Hill Gold Mine operation. On-going system development and improvement initiatives are planned to add further value for the future.

Jan 1, 2000

Concentrations of bright green material in the "Golden Mile" of Kalgoorlie, which carry particularly high gold values, are known locally as "green leader".This assemblage consists largely of quartz, sericitic muscovite, carbonates, and pyrite. Some of the sericitic muscovite contains vanadium, giving the rock its green colour. Vanadium oxides, including nolanite, are also present. Tellurides identified in this study are calaverite, altaite, petzite, melonite, and coloradoite. Native gold was found in most of the samples; some of the gold, at least, has been formed from the decomposition of gold tellurides.It is suggested that mineralizing solutions carrying gold and tellurium leached vanadium from the host rocks and subsequently deposited gold tellurides and vanadium-bearing minerals in the "green leader".

Jan 1, 1977

By Mohammad Djavid

The one-pass tunneling pipe jacking method has often been the most schedule and cost efficient method for the pipe line installation. The main challenges in jacking pipes larger than 108 inches and for longer runs are: transportation and logistics, requiring high jacking forces, keeping line and grades, control of ground surface settlement, providing adequate external lubrication, and the potential of damaging the joints and pipe spigots. In recent years, 144" diameter pipes have been jacked for short runs of up to only 300 feet. In this article design and construction of installation of up to 1,000 linear feet run of 144-inch internal diameter, reinforced concrete pipes without intermediate jacking station in Chicago O?Hare International Airport are discussed. The article also presents discussions regarding the subsurface saturated silt formation, shallow cover, dewatering, jacking and receiving shafts, jacking forces, lubrication and settlement data.

Jan 1, 2008

By Corinne Boone

CO2e.com, LLC - launched in November 2000 - aims to be ?the global hub for carbon commerce.? CO2e.com is a subsidiary of the Cantor Fitzgerald Group, one of the world?s leading brokerage firms Recent Investor in CO2e ? Mitsui & Co. Alliance with Cantor Fitzgerald Environmental Brokerage Services Group (CFEBS) Offices in London, Toronto, Tokyo, New York, San Francisco, Los Angeles, Connecticut, Houston Primary Goals/Benefits of ET § Goals of Emissions Trading: ? Permit Industrial Growth/Expansion ? Promote Economic Efficiency and Flexibility in Meeting Air Pollution Standards § Benefits of Emissions Trading: ? Enhance Air Quality w/o Economic Stagnation ? Encourage Development of New Technology ? Foster Most Efficient Use of a Limited Resource -- Clean Air § Contributes to Sustainable Development and objectives of UNFCCC, Kyoto Protocol?.

Nov 1, 2002

By Caroline Gomes de Oliveira

A busca por materiais que atendam as demandas ambientais que vem surgindo com o passar dos anos abre um importante mercado para a aplicação de fibras naturais. Além de biodegradáveis e provenientes de fontes renováveis, as fibras naturais possibilitam a produção de materiais compósitos de baixa densidade e com boas propriedades mecânicas. Para aumentar ainda mais essas propriedades, estuda-se o uso de tecidos de fibra natural em vez das fibras alinhas. As principais vantagens desta nova configuração são o reforço em mais de uma direção ao mesmo tempo e o fato de serem mais compactos, viabilizando a incorporação de uma fração maior de material de reforço. O presente trabalho investigou a resistência ao impacto de compósitos de matriz poliéster reforçados com tecido puro de rami, que é uma das fibras lignocellusosicas mais resistentes encontradas até hoje. Os corpos de prova foram reforçados com 1, 2 e 3 camadas de tecido e foram ensaiados num pêndulo de impacto Izod. Concluiu-se com base nos resultados que o aumento da fração volumétrica de tecido aumenta a resistência ao impacto dos compósitos.

Aug 17, 2017

By W. A. Scheuch

ORDINARILY secondary copper, unless electrolytically refined, is reclaimed directly as foundry ingots used in the manufacture of copper-rich alloy castings. This use does not require the elimination of the impurities to the degree required if the recovered metal is to be used for electrical purposes where a high electrical conductivity is of prime importance. However, as a part of the general policy of reusing its own scrap and by-products wherever possible, the Western Electric Co. at its Hawthorne Works is recovering its secondary copper as wire bars which are delivered to its own rod and wire mill and there processed into wire of high electrical conductivity. This departure from the usual recovery scheme has been accomplished through the careful classification and sorting of the material entering the furnace charges and the careful control of the subsequent melting and refining in a reverberatory furnace. Tests conducted over a period of approximately four years have shown that the quality of wire bars produced from selected secondary copper is equal to that of wire bars produced by the electrolytic refineries. The interest which has been exhibited in the process by those who have seen it has prompted the following general description. It is the authors' opinion that the recovery of secondary copper will become more and more an important factor in the copper production industry. The description is largely of the refining furnace and its operation, but it must be remembered that careful classification and sorting of the scrap materials to eliminate impurities are just as important as the furnace operation toward obtaining a satisfactory final product. Classification and sorting do not lend themselves easily to description; they must just be done. It should also be recognized at the outset that constant intelligent supervision is requisite to the success of the process because there are so many ways in which impurities can find their way into the final product.

Jan 1, 1929

By Kumar A, Mishra N. C

For each tonne of chromite ore mined in Sukinda, approximately ten tonnes of fine overburden material is generated. The overburden typically contains about 30 - 60 per cent Fe2O3, 0.3 - 1.1 per cent Ni, four to nine per cent Cr2O3 and 0.04 - 0.2 per cent cobalt and is being discarded leading to loss of valuable metals and creating environmental pollution. In order to take the advantage of presence of iron, nickel and chromium, the present studies advocate the utilisation of nickel lateritic chromite overburden for production of Ni bearing pig iron through blast furnace extracting maximum iron and nickel from the chromite overburden. The present paper deals mainly with the beneficiation of chromite overburden, sintering characteristics and thermodynamic studies. The beneficiation study shows that a beneficiated concentrate having Fe - 50 per cent and Ni -- 1.1 per cent can be achieved from chromite overburden having Fe - 30 per cent and Ni -- 0.7 per cent. Sintering studies have been carried out with bed height of 300 and 450 mm at a suction of 600 and 900 WG respectively. The results reveal that good quality sinter can be produced from chromite overburden concentrate with a basicity of about 1.0 and coke breeze consumption rate about 16 per cent. In all the experiments, Tumbler Index, Abrasion Index and Shatter Index was found to be in the range of 65 - 70, 4.5 - 5.5 and 85 - 90 respectively. The other parameters namely softening temperature, melt down temperature, reduction degradation test and relative reducibility have also been determined. A thermodynamic analysis has also been carried out to make a technological assessment of the process for the production of alloyed pig iron from chromite overburden in blast furnace which shows that it is possible to produce nickel bearing pig iron in blast furnace using the sinter up to 80 per cent. Techno-economic analysis reveals that this route will yield a substantial profit even after accounting for cost of beneficiation, extra coke, raw materials and extra slag produced.

Jan 1, 1999

Theories of ore genesis. have both practical and philosophical application-practical in that they influence our search for new ore bodies; philosophical in that they provide a test for our theories of petrogenesis-and our ingenuity.For example, the theory of granitization requires an explanation of ore genesis compatible with the general concepts of granitization.Our understanding of some processes of ore formation, such as supergene enrichment, or the formation of residual lateritic iron ores, is so complete as to permit of nq controversy.For other ores, like the oolitic iron ores of England and France, and elsewhere, or the segregations of chromite or ilmenite in basic igneous rocks, the broad principles are generally agreed on; dispute is limited to details of process.But for a wide range of ore deposits there is no such agreement. Completely incompatible hypotheses are advanced to explain' identical facts, and we have difficulty in finding new facts or criteria that will distinguish unambiguously between them.In thinking about such ores, a co:n;venient starting point is provided by Schneiderhohn's (1953) fourfold division of ore deposits:1. The secondary hydrothermal ore deposits occurring in Mesozoic-Neozoic cover strata of Europe.2. The "regenerated" younger ore deposits in Alpine type mountain chains.3. Post-Cambrian primary hydrothermal ore deposits.4. Ore deposits of the PreCambrian shields.To these we may add a fifth group:5. Stratigraphically controlled sulphide deposits.

Jan 1, 1956

By P. B. Baxendell

The appraial of producing properties and profitability ntzalysis of a proposed capital expenditure are based on the same principles. In both problems a projection of future cash income is. cornpared to one or more capital expenditures. Several different methods have been in use either to compute a price to obtain a given earning power on the investment or to compute the earning power which will result from a given capital expenditure. One of these, the "Average Annual Rate of Return" method, computes in a simple manner the ratio of the present value of the future earnings after amortization to the present value of the undepreciated balances of the investment over the life of a project. This method, not well known generally, appears to have some rather unique advantages in reducing the computation work required, eliminating trial-and-error solutions, and providing a more accurate answer when applied to oil industry investments subject to the unit-of-production basis of amortization. Its derivation is given and its versatility demonstrated in the solution of certain everyday investment problems. A number of charts, useful in applying this method to profitability analysis and appraisal work, are provided. The current trend in the market values of producing properties is shown. INTRODUCTION Making sound capital expenditure decisions requires an objective means of measuring the productivity of individual investment proposals. Since the best measure of the economic worth of such proposals is their ability to produce profits, it is common practice to grade proposed capital expenditures according to their annual earning power as a percentage of the outstanding capital. The same principles which govern the determination of the rate of return of proposed capital expenditures also apply generally to the problem of determining the appraisal value or purchase price of income-producing oil and gas properties. Both problems are of prime importance in the producing phase of the oil business, where management is faced daily with decisions to drill or not to drill certain development wells, or with the determination of the appraisal value of producing properties. The common feature in both problems is that a projection of future cash income is compared with a known or estimated capital investment to determine itsiearning power or annual rate of return. In the case of development drilling, the cost of the proposed well can usually be estimated with a fair degree of accuracy and the problem consists of finding the rate of return on the invested capital. In the case of appraising producing properties, on the other hand, the desired rate of return is usually known in advance and the problem consists of determining the purchase price which, for the given income projection, results in the fequired rate of return. Certain accounting procedures common to the oil and gas producing business make these two problems and their solutions somewhat different from corresponding problems in other industries, and, in certain ways, simpler. The main difference is in the amortization policy which, for oil and gas production, is frequently on a unit-of-production basis, compared to the amortization on a time basis used in many other industries. The purpose of this paper is to discuss briefly the various methods currently in use for the measurement of productivity of invested capital in producing properties and, in more detail, the derivation and application of what will be called the "Average Annual Rate of Return Method". This rather interesting and not too well known method has some very definite advantages in the solution of many problems common to the oil industry. For the sake of simplicity, federal income tax considerations have been disregarded in the examples used, since they do not affect the principles involved. The use of the production payment route in the sale or purchase of producing properties, which has been amply covered in many other publications, has also not been included in this analysis. METHODS FOK MEASUKING THE EARNING POWER OF INVESTED CAPITAL, Of the many different methods used to measure the earning power of invested capital, four are applicable to oil or gas production ventures. Depending on whether these four methods utilize one or two interest rates, and whether a fixed amortization pattern is used, they may be classified as follows.

By T. Holmes, D. C. Russell, G. Jolly

"The AMEC Oakville office is involved in the design and construction of an iron ore concentrator located in Liberia. Currently, the site ships Direct Shipped Ore (DSO) to overseas customers. The DSO mine-site and port can experience heavy annual rainfalls. The IMSBC Code requires that cargoes are only accepted for loading when the moisture content of the cargo is less than its Transportable Moisture Limit (TML). The moisture content of the DSO has, on occasions, risen to near or above its TML. AMEC was asked to advise whether the concentrate produced from the new concentrator would or would not have the same problems with moisture content and ship loading as the DSO.INTRODUCTION Liberia was, at one time, the world’s sixth largest exporter of iron ore and used some of the most modern mining operations of their time. However, the country has not produced iron ore over the past seventeen years because of civil unrest. The return of stability to the country has allowed the redevelopment of the iron ore industry. ArcelorMittal Liberia (AML) obtained a concession for mining in the Nimba County area of Liberia (Figure 1) in December, 2004 and has studied the known iron ore deposits and former mining operations in this area. It began phase 1 operations in June 2011 with the direct shipping of high grade ore at a rate of up to 4Mtpa. The processing of the lower grade ore in phase 2 of the project requires additional processing capability to produce at the design rate of 15Mtpa. DSO and Concentrate The DSO in the first phase is selectively mined at an average grade of 60% Fe, and then crushed and screened to -10 mm with no washing or concentration. Testing of samples has indicated a size distribution that is finer than typical sinter feed material, although critical material below 0.10 mm is low in most cases, and overall the ore is coarser than typical concentrates or ultrafine products (Feasibility study report, 2011). The phase 1 DSO facility will cease operation after the phase 2 concentrator comes into operation."

Jan 1, 2014

By Hebert Arias, Christian Mendoza, Mervin Tapia

El Complejo Pasco —ubicado en la Cordillera Oriental de los Andes de la sierra central del Perú, en el distrito de San Francisco de Asís, provincia y departamento de Pasco— está constituido por las unidades subterráneas de Atacocha y Porvenir, la operación a tajo abierto Glory Hole y tres proyectos brownfield ubicados en la periferia de la concesión. Tanto Atacocha como Porvenir son depósitos tipo skarn, con mineralización distal de Zn y Pb(+/-Au) y proximal de Zn+/-Cu, asociados a cuerpos hipoabisales de composición cuarzoandesítica y andesítica. Estudios y exploraciones recientes muestran otros tipos de sistemas mineralizados, como brechas tectónicas con reactivación hidrotermal tardía, un sistema epitermal de sulfuración intermedia en vetas, cuerpos irregulares, entre otros, y un sistema tipo pórfido. La Falla Milpo-Atacocha, de rumbo N-S, juega un rol importante, ya que los intrusivos (Stock Milpo y Santa Bárbara) que generan la mineralización del tipo skarn están controlados por esta falla. Existe otro tipo de mineralización, asociado al sistema NW-SE (Falla 13): un sistema epitermal de sulfuración intermedia. Este trabajo pretende mostrar los últimos avances en las interpretaciones metalogenéticas, producto de un intenso programa de exploración (aproximadamente 80,000 m. DDH / 2018) y de un programa de recategorización de recursos (a través de 60,000 m. DDH), que permitirá hacer posible una operación sostenible de 12 años.

May 22, 2019