Search Documents

This paper covers only the energy uses of natural resources and does not deal with non- energy uses, which in 1975 were of the order of 10 per cent of the total consumption of energy resources. The United Nations `J' Series of Statistics ex- presses each of the various forms of energy in terms of its coal equivalent in metric tonnes and this basis is followed in this paper. One tonne of black coal (referred to as tce) has been taken as the equivalent of the following. 29 X 109 joules or 27.5 X 106 Btu 0.68 tonnes or 4.8 barrels of crude oil 750 cubic metres or 26.5 X 103 cubic feet of natural gas 1 ò5 to 3.3 tonnes of peat or lignite (world average 2.54; Victorian brown coal 3 0) 8055 kWh (at 3.6 X 106 joules or 3412 Btu per kWh at 100% efficiency) 2660 kWh at 33% efficiency of generation 50 grams of uranium present in natural uranium reactors (see note later under nuclear energy) 0.8 grams natural uranium in breeder reactors Nuclear and hydro electricity are expressed as the coal equivalent required to produce, at 33 per cent efficiency, the same amount of electricity. In other words, electricity produced by these sources is converted to its coal equivalent at the rate of 2660 kWh = 1 tonne coal.

Jan 1, 1978

As the high-grade copper deposits in the world become depleted, there is an increasing focus on developing lower-grade ores which contain problematic impurities such as arsenic. Indeed, many high-arsenic ore bodies remain undeveloped because of their high arsenic levels. Separation of arsenic from copper at the beneficiation stage is difficult using the current processing techniques and invariably copper concentrates produced from these ores contain high arsenic levels, sometimes so high as to make them unacceptable to copper smelters. New, sustainable approaches are needed to allow development of high-arsenic copper ores while at the same time minimizing arsenic dispersion into the biosphere. The most promising route for separating arsenic from copper at the flotation stage centers on the use of pulp potential control. In recent years CSIRO has demonstrated at laboratory scale, for a number of high-arsenic copper ores, that crude flotation separation between arsenic-bearing minerals and copper-bearing minerals can be made. The differences in specific minerals responses to changes in pulp potential and pulp pH are exploited for this separation. Such separations nominally produce a low-arsenic high-copper concentrate and a low-copper high-arsenic concentrate. The former can be smelted without penalty, while the latter requires further treatment to capture and stabilize the arsenic and to recover the residual copper. Consideration has now been given to treatment options for the high-arsenic low-copper product. A pyrometallurgical option, involving a low temperature roast to selectively fume off the arsenic and leave a high-copper calcine, coupled with an arsenic stabilization step, has been demonstrated in the laboratory, and a preliminary techno-economic evaluation shows the process to be economically favorable. These results were recently published. CSIRO has now investigated an alternate hydrometallurgical option, involving atmospheric alkaline sulphide leaching of the high-arsenic product, where the arsenic is selectively dissolved leaving a copper-rich leach residue. The leaching testwork was carried at on the same high-arsenic low-copper material used in the roasting studies, enabling a techno-economic comparison of the alternate roasting and leaching treatment options to be made. The alkaline leaching work is briefly described and the results of the process option comparison presented and discussed. Keywords: arsenic, copper, economics, enargite, ore flotation, tennantite INTRODUCTION

Sep 1, 2012

By Foluke Salgado de Assis

Este trabalho visa apresentar os resultados obtidos através de ensaios balísticos realizados em sistemas de blindagem multicamada tendo como camada intermediária o compósito de poliéster reforçado com fibras de juta. Seguindo as especificações da norma americana NIJ 0101.06, foram realizados ensaios balisticos utilizando munição de calibre 7,62 x 51 mm, que possui velocidade acima de 800 m/s. A blindagem multicamada utilizada possui como camada frontal uma pastilha hexagonal cerâmica (alumina dopada com 4% de nióbia), segunda camada de compósito de matriz poliéster reforçada com manta de juta e terceira camada uma placa de alumino 5052 H34. A utilização de compósitos poliméricos reforçados com fibras naturais em substituição às fibras de aramida é de grande interesse, pois além de desempenharem a mesma função no sistema de blindagem, possuem um valor de mercado bem menor. Os resultados de profundidade de indentação na plastilina atenderam a norma NIJ 0101.06 e utilizando a técnica de microscopia eletrônica de varredura, verificou-se que o compósito poliéster-juta capturou os fragmentos cerâmicos através do mecanismo de incrustação mecânica.

Oct 30, 2017

1. Book reviews Geophysical and geochemical techniques for exploration of hydrocarbons and minerals, edited by M. Sittig. (Reviewer: J. Keenan) Separation procedures in inorganic analysis. A practical handbook, by Roland S. Young. Charles Griffin, 1980. £23.00. (Reviewer: R. Murray-Smith) 2. Historical reprints Theinin~rs dictionary, by William Hooson. £14. Discovery of subterraneal treasure, by Gabriel Plattes. £12. Fodinae Regales (The Mines Royal), by Sir John Pettus. 3. De Beers' booklets Amborite - a remarkable new cutting material, by De Beers Industrial Diamond Division (P.O. Box 916, Johannesburg 2000). Booklet, 14 pp., free of charge. Natural and synthetic micron powders, by De Becrs Industrial Diamond Division (P.O. Box 916, Johannesburg 2000). Leaflet, 5 pp., free of charge. 4. New books Nickel in the environment, edited by J. O. Nriagu. New York, Wiley, 1980.928 pp. $65. Underwater minerals, by D. S. Cronan. London, Academic Press, 1980. 364 pp. $57.50. Data conversion integrated circuits, edited by D. Dooley. New York, Wiley, 1980.298 pp. $26.95 (cloth), $17.50 (paper). 5. NIM reports Report 2057 A mineralogical study of the Rooibokkop- Boschhoek copper deposit in the Marble Hall area. Report 2069 A utomatic setting of the distance between sample and detector in gamma-ray spectroscopy. Report 2070 The prereduction of chromites from the UG-2 Reef. Report 2075 The optimization of some of the conditions for analysis by spark-source mass spectrometry. Report 2082 A survey of the literature on gravity separation.

Jan 1, 1981

By I. O. Ojala

Detailed knowledge of velocity-depth trends is essential for constructing well-to seismic ties, determining background velocity and generating synthetic seismic traces for interpreting seismic amplitudes in terms of porosity, lithology and pore fluid type. The acoustic properties of shales are of particular importance in the exploration setting as shales constitute more than 80% of sediments and rocks in siliclastic environments. Seismic and sonic log data may be used for estimating overpressure in shales in order to maintain borehole stability during drilling. In addition, velocities in shales can be used for predicting its mechanical properties and hence, borehole collapse. Despite of the apparent importance of understanding shale acoustics, sonic logs in shales are frequently unavailable or unreliable especially for older wells. Hence, it is essential to compute pseudo-velocity logs from other available information. This can be accomplished by using empirical relationships or rock physics transforms. In this study we have compared the predictive power of resistivity (Faust 1951, Hubert 2008) and porosity based models (Wyllie 1956, Holt & Fjær 2003) for computing synthetic P-wave velocity logs using wireline log data from mudstone intervals at three North Sea wells. The wells 6507/2-1, 6507/2-2 and 6507/2-1 are located at the Haltenbanken area at the Norwegian Sea. The wells targeted hydrocarbon potential at the upper Cretaceous and lower Tertiary sandstone sequences. The sandstone beds are overlain by thick Tertiary and Cretaceous sequences of mudstones. Since our primary goal is to model acoustic velocities in shale, we used wireline data from the Nordland (NL), Rogaland (RL) and Hordaland (HL) groups that are mainly composed of mudstone. The mudstone beds were identified from the well log data by using natural gamma log, sonic and resistivity data as well as information from the Norwegian Petroleum Directorate website. The volume of shale was estimated from the natural gamma log and the data points with values higher than 0.65 were discarded. Similarly, the data points with shale volume less than 40 % were discarded. Furthermore, exceptionally high resistivity values amounting to more than 6 Ohm m were not included in the analysis. Porosities were determined from the density log assuming 2.7 and 1.05 g/cm3 for matrix and fluid densities, respectively. The depth that was used for calculating Vp from Faust (1953) was the depth below mudline in order to the compare of well data from wells that have been drilled at different depths (Hubert 2008).

May 1, 2009

By B. A. Kulp, R. R. Reeber

Lattice parameters for the wurtzite form of' CdS mere measured by powder X-ray diffraction techniques over the temperature range 26° to 1000 K'. A negative thermal -expansion coefficient was determined parallel and perpendicular to the c axis below 13.5°K. Near 808°K, the curves of the a, parameter, the differential thermal expansion, and the resistivitv vs absolute temperature exhibited a reversible discontinuity. j\. direct determination of the lattice parameters of CdS over an extended temperature range is of particular use in interpretation of the effects of high pressure on the band structure of semiconductor materials. For example, Langer' has studied the effects of pressure on the absorption edge of CdS from 77°K to room temperature. In order to properly interpret his results it is necessary to know the change in lattice constants as a function of temperature for the wurtzite, zincblende, and rocksalt2 modifications of this material. Thermal-expansion measurements for CdS, wurtzite phase, have previously been determined over a limited temperature range.s74'5 The zincblende phases, of other compounds with similar bonding, have been investigated by Novikova et a! .'' Previous thermal-expansion measurements for metals with hexagonal symmetry have for the most part used bulk sample techniques for low-temperature result. Most X-ray measurements at low temperature have been on materials with cubic symmetry.'jQ The use of X-ray powder-diffraction techniques offers a convenient and accurate method of measurement over a wide temperature range. The X-ray method, besides measuring unit cell size, also provides information about change in structure type and the nature of some of the stacking defects present. I) EXPERIMENTAL PROCEDURE The thermal expansion was measured by X-ray powder-diffraction techniques. Lattice parameters for the range 300" to 1000°K were determined in a 19-cm Unicam camera. From 26" to 300°K a 34-cm back-reflection camera with the Van Arkel" film arrangement was used. The sample was bonded to a copper cold finger below a helium, hydrogen, nitrogen, oxygen, dry ice, or ice brine bath in a metal cryistat. che inner bath was surrounded by another one for radiation shielding. Nitrogen was used in this outer bath for the very low-temperature runs while dry ice and acetone was used for the 195°K point. CuKa X-rays, filtered with a nickel foil, entered the cryostat through a 0.001-in.-thick aluminum window. During a typical 9-hr exposure the sample was continuously rotated through a 30-deg arc. Heat losses from the sample holder limited the minimum temperature attained to 26°K with helium in the inner dewar. Temperature calibration between 25" and 125°K was determined with an Allen Bradley 300-ohm carbon resistor. The resistor was attached to the back of the copper finger with a thin layer of silicone grease. Liquid He, HZ, N2, and O2 baths were used to calibrate the resistor. Temperature variation is estimated to be *2"K with a slightly higher uncertainty at room temperature and 264°K. The thermal expansion of high-purity germanium from 373" to 900°K was measured as a calibration for the Unicam camera. This value was compared with the known value1' for the thermal expansion. A discontinuity in the thermal-expansion coefficient of the CdS a, parameter was observed. Similar discontinuities in the resistivity and differential thermal analysis at the same absolute temperature indicate that the temperature error is *5°K in the temperature range above 500°K. Temperature errors in the Unicam camera below 500°K are appreciably higher due to large gradients in the resistance furnace. II) SAMPLE PREPARATION The CdS was Eagle Picher ultrapure grade. The crystallite size range of the as-received powder

Jan 1, 1965

Reverse flotation process tests were conducted for marine sedimentary silicon-calcium phosphate ore in this research. The research findings showed that by adding antifoamer, a concentrate with P2O5 32.36%, SiO2 10.69%, MgO 0.67% was obtained, with recovery of P2O5 being 88.12%. Such is a satisfying result, when compared with the original mineralogical component of P2O5 26.64%, SiO2 11.51% and MgO 3.36%. When using antifoamer, the SiO2 grade of the concentrate increased 0.55%, the MgO grade decreased 0.64%, while P2O5 recovery increased 2.69% compared by adding no antifoamer. Adding antifoamer is favorable to increase the grade and recovery of P2O5. Therefore, antifoamer is necessary. Tests of synergistic reaction of antifomer indicate that the appropriate consumption of the antifoamer is 275g/t CY and 1Kg/t TWF. Keywords: silicon-calcium phosphate ore, desilication, antifoamer, reverse flotation

Sep 1, 2012

Although the pattern of metamorphic zones south of the Thackaringa-Pinnacles Fault is much obscured by polymetamorphism, displacement of the orthopyroxene isograd by the fault agrees with the displacement of a horizon of "banded aplite" mapped by Andrews (1922). A dextral transcurrent component of 20,000 ft is indicated.INTRODUCTIONThe east-west Thackaringa-Pinnacles Fault (Andrews, 1922; King and Thomson, 1953), one of the major geological structures in the Broken Hill district, New South Wales, cuts across the general north-easterly strike of outcrops and fold structures of the Willyama Complex. The degree of shearing and recrystallization in its unusually wide crush zone and the manner in which adjacent rock units and structures have been dragged into conformity with its strike denote considerable movement on the fault. Information concerning the nature of this movement is of critical importance in the search for possible continuations or repetitions of lead-zinc mineralization south-west of Broken Hill.A transcurrent movement of 20,000 ft, with the southern block moving west, was estimated by Andrews (1922), who correlated prominent outcrops of "banded aplite" at The Pinnacles (north of the fault) and Big Hill (south of the fault). Displacement of this order, however, does not seem sufficient to explain the extent and character of the fault zone. Recent chemical and petrological studies of the banded aplites at The Pinnacles and Big Hill by Vernon (19B1) confirmed their similarity, but indicated an origin by metasomatic replacement of pre-existing folded and metamorphosed rocks. This raises the possibility that some...

Jan 1, 1965

By N. Kumar, A. K. Dhawan, A. Varughese, S. K. Khullar

Abstract The in-situ stress field is one of the primary parameters influencing the performance of underground structures particularly in the Himalayas where there is strong influence of topography and geology on in-situ stresses. It is always advisable to measure the in-situ stresses, in whatever best way possible. Hydrofracturing is one of the methods by which in-situ stress can be measured. This paper briefly describes details of the concept of Hydrofracturing in arriving at the in-situ stresses of the rock mass at Pancheswar Project. The data obtained from the tests has been analysed, interpreted and the results are presented in this paper. Kurzfassung Das Spannungsfeld an Ort und Stelle ist einer der wichtigsten Parameter, die das Verhalten der Untergrund-Struktur beeinflussen, insbesondere in den Himalayas, wo die Topografie und die Geologie einen grossen Einfluss auf die oertlichen Spannungen ausueben. Es empfiehlt sich stets die Spannungen an Ort und Stelle so gut wie moeglich zu erfassen. Die Hydrofraktur bzw hydrografisches Zerstueckeln ist eine der Methoden, die bei den Messungen der oertlichen Spannungen verwendet werden koennen. Diese Abhandlung beschreibt kurz Einzelheiten ueber das Konzept von Hydrofraktur bei der Bestimmung der Spannungen an Ort und Stelle von der Felsmasse bezueglich des Projekts Pancheshwar. Die gewonnenen Daten aus den Messungen wurden analysieret und ausgewertet. Die Ergebnisse werden dabei vorgelegt. Sommaire Le champ de contraintes in-situ est un des paramèters principaux influencant l’exécution des structures souterraines particulierèment en Himalaya où les forces in-situ sont fortement influencées par les caractéristiques topographiques et géologiques de la région. La fracturation hydraulique est une technique qui permet de mesurer des forces in-situ des massifs rocheux. Cet article décrit brièvement le mécanisme de fracturation hydraulique et présente les résultats de mesure des forces in-situ des roches au site du projet hydroélectrique de Pancheswar.

Jan 1, 2003

By Joseph A. Holmes

The investigations carried on at the fuel-testing plant of the United States Geological Survey at St. Louis in 1904-1907 included tests of the steaming and gas-producing qualities of many coals and of the possibilif3 of their improvement by briquetting, together with washing and coking tests and tests of some of the resulting coke in the cupola. These tests were part of a general inquiry into the manner of utilizing most efficiently each of the coals under investigation. The equipment used in the cupola tests of coke, the manner of conducting the tests, and the essential results have been described in publications of the Geological Survey," and only the more important conclusions to be drawn from the tests are mentioned in the following pages. The tests were made to show the fitness of the cokes for foundry purposes, but an incidentlll result was to show foundry men and the coke producers the advisability of studying the conditions of foundry practice. The present bulletin, published by the Bureau of Mines because the analyzing and testing of fuels have been transferred from the Gilological Survey to the Bureau of Mines, briefly reviews the status of the coke industry, some features of practice in the use of coke in the foundry, the probable happenings of a cupola heat, and the reasons for modifying charging practice so that a particular coke can be used to best advantage.

Jan 1, 1910

By H. E. Heide

"Before the war, the United States was the world’s leading consumer of tin, the industrial applications of which had become widespread. Domestic production was negligible, and requirements were met almost entirely by imports, principally from British Malaya, United Kingdom and China. Average annual imports for the years 1925-1929 amounted to 78,009 long tons.With the advent of war in Europe and signing of the Japanese-German pact, it was realized that foreign sources of supplies were threatened, and steps were taken by Congress to forestall critical shortages of tin and other minerals. These steps in regard to tin included stock-piling, improving reclamation and conservation, increasing South American production, constructing a smelter in the United States for treatment of tin, ores, and intensifying the search for domestic tin deposits. Annual imports were raised to 140,873 long tons by 1941. On 1945, annual imports had shrunk to 37,675 long tons and consumption had been reduced to 52,100 tons of primary and secondary tin but not tin content of scrap alloy.The Strategic Minerals Act, passed by the Congress in 1939, authorized the investigation of domestic tin deposits.As Alaska had supplied virtually all of the domestic output of tin, an investigation of Alaska deposits was undertaken in 1940 and 1941 by J. B. Mertie, Jr., and Robert R. Coats of the Geological Survey.The Lost River lode tin mine on the Seward Peninsula was examined by H. E. Heide of the Bureau of Mines in 1942. Possibilities for developing a significant amount of tin appeared favorable, and exploration of the ore bodies was started in August 1942."

Jul 1, 1946

By V. V. Clark

WHEN a district is more or less primitive, and a trained mining engineer attempts single- handed to prospect it according to old standards, he generally fails. He has not the ability to live out in the open alone for months at a time and carry on with enthusiasm and determination like the old-time prospector. But the same engineer, placed in an organized group where modern prospecting methods are employed, is immediately put on his mettle and his chances of winning are greatly increased. Marsman Investments, Ltd., with headquarters in Manila, has at the present time, Sept. 4, 1937, six prospecting parties in the Netherland East Indies. Three of these groups are combing their assignments for lode mines, studying structures, developing and reaching out into veins and zones with diamond drills. The other three are searching for placer mines with pans, pits, and Empire drills. I am in charge of one group seeking commercial gold placers on the Island of

Jan 1, 1937

Separation of Nickel and Cobalt from Manganese, Magnesium and Calcium by Synergistic Solvent Extraction - From Batch Tests to Pilot Plant Operation The synergistic solvent extraction system consisting of Versatic 10/LIX63/TBP was used for the separation and purification of nickel and cobalt from synthetic laterite leach solution after iron removal. Very encouraging results were obtained for separating nickel and cobalt from manganese, magnesium and calcium. In batch tests, the organic composition of the synergistic system was optimised and very large synergistic shifts for nickel and cobalt were observed. The ?pH50(Mn-Co) and ?pH50(Mn-Ni) values were as large as 1.65 and 2.40, respectively. The extraction and stripping kinetics of nickel and cobalt was fast. Semi continuous extraction tests were conducted with a pH profile of 5.5/6.1/6.5 in three stages at 40¦C. The nickel and cobalt extractions reached 99.9 per cent with only 5 mg/L Ni and <1 mg/L Co left in the raffinate. With two stages of scrubbing, only 2 mg/L Mn and less than 1 mg/L Mg and Ca were left in the scrubbed organic solution. With two stripping stages, the stripping efficiencies of Ni and Co reached over 95 per cent. A fully continuous pilot plant operation was conducted successfully for 280 hours. With an O/A ratio of about 2 and a pH profile of 5.5/5.8/6.0/6.3 for the four stages EX1/EX2/Ex3/EX4, both nickel and cobalt were almost completely extracted. Using a pH profile of 5.4/5.0 for SC1/SC2, the manganese scrubbing efficiency was over 96 per cent. Using three strip stages, over 98 per cent Ni and 99 per cent Co were stripped with only 64 mg/L Ni in the stripped organic solution. The nickel concentration in the loaded strip liquor reached 83 g/L, resulting in a ?Ni of over 28 g/L. The chemical stability of the system was also assessed over 12 weeks under proposed industrial operating conditions. Operation exclusively under strip conditions at 50¦C and 40¦C resulted in LIX63 oxime half lives of 1.1 and 2.1 years, respectively. Operation exclusively under extract conditions at 50¦C and 40¦C resulted in oxime half lives of 0.26 and 0.82 years, respectively. Losses of Versatic 10 were less than four per cent.

Sep 13, 2010

By A. M. Tunstall

Aspects of blast vibrations, damage mechanisms and the influence of rock quality on damage severity are reviewed and results presented from a monitoring programme in which the rock mass rating for six tunnels was determined. The peak particle velocity induced in the tunnels during open-pit blasting was measured and the tunnels were inspected visually for fresh damage after each blast. The results suggest that the quality of rock in which an excavation is situated has an influence on the level of ground vibration to which it can be subjected without sustaining damage. This means that the use of a single limiting value of peak particle velocity, as in the blast damage criteria for residential structures, is not ideal and may result in damage to excavations in poorer-quality rock masses

Jun 19, 1905

By G. B. Harris

It has long been appreciated that chloride chemistry has a number of advantages over the more traditional sulphate route for both extracting and separating metals. Modern materials of construction, coupled with the development of a more cost-effective and efficient hydrochloric acid regeneration technology mean that chloride-based processes are now more competitive and attractive. Such processing routes are able to recover more of the contained metal values in a feed, including iron in a benign and/or marketable form, and particularly the so-called rare and rare-earth elements which are increasing in demand in our electronic age. These factors, therefore, add appreciably both to the overall economics of a project, but also offer a much more sustainable approach to our dwindling natural resources. Additionally, chloride-based flowsheets can be much more environmentally-friendly, offering practical alternatives to two of the biggest headaches faced by the industry, namely cyanide usage and the generation of red muds. This paper presents a brief theoretical background, focusing on the latest developments of ferrous iron oxidation and the low-temperature, selective hydrochloric acid regeneration process, which is the key unit operation for any chloride flowsheet, and discusses in general the advantages of the chloride approach. Several recently-developed flowsheets, which have been tested at the miniplant level, are presented for gold, base metals, titaniferous magnetites and lead-silver ores wherein the advantages of considering a chloride approach are highlighted.

Jan 1, 2014

By Robert E. Barieau

A list of 163 references to original experimental PVT data on helium is presented for the period 1895 to 1968. The list is complete as of the start of the Helium Centennial Year, 1968, to the best of the author's knowledge. Citations were keypunched for easy updating and are listed alphabetically by author.

Jan 1, 1968

Our mission is help ensure our country has an adequate, dependable supply of minerals and mate al to meet its national security and economic needs at acceptable social, environmental, and economi[c] costs. We do this by promoting and encouraging private enterprise in the development of viable and stable mineral industries through the transfer of innovative extraction, processing, recycling, an environmental technologies; our use of cooperative partnerships with industry, academia, an government; our timely, authoritative worldwide mineral intelligence; our advocacy of public policies based on good science and sound economics.

Jan 1, 1994

By Jheison Lopes dos Santos

O presente estudo teve por objetivo principal produzir um cerâmico composto de alumina, nióbia e fluoreto de lítio de forma a otimizar o uso do forno na etapa de sinterização. Para isso, ponderou-se a respeito da necessidade ou não de utilização de um patamar a 1000°C utilizado em estudos anteriores. Além disso, buscou-se diminuir a temperatura de sinterização, assim como o tempo de permanência em tais temperaturas. O composto cerâmico (Al2O3–4%Nb2O5)–0,5%LiF foi sinterizado a três temperaturas diferentes (1200, 1250 e 1300 ºC), com tempo de patamar de 1h. Foi realizado ensaio de Arquimedes para analisar sua densificação e determinar sua densidade. As fases formadas nessas temperaturas foram identificadas por difração de raios-X. Os resultados mostraram que a maior densificação foi obtida para a maior temperatura, de 1300 ºC. Foi possível observar também que um patamar de apenas 1h na temperatura de sinterização de 1300 ºC apresentou igual densificação a de outros trabalhos, com tempo de patamar de 3h. Este fato sugere que a temperatura tem maior influência na sinterização do que o tempo de permanência. Verificou-se ainda que as mesmas fases foram formadas nas três temperaturas investigadas, sendo tais fases as mesmas detectadas em trabalhos anteriores com patamares maiores. Isso mostra que o prolongado tempo de 3h no patamar de sinterização apenas favorece o crescimento dos grãos, bastando apenas a permanência de 1h para alcançar os resultados desejados e com grãos menores.

Oct 30, 2017

By Vincent Scovazzo

This paper compares the two most common pillar design equations used worldwide by John T. Boyd Company; the Mark-Bieniawski Equation, an empirical approach, and the Wilson Equation, an analytical approach. The equations are compared in two ways; by their stress profiles and by the Mark-Bieniawski Equation stability factor. Contrasting the two equations based on the visual comparison of their stress profiles is straight forward but evaluating their resulting pillar designs is problematic. Complications arise due to the differences between the use and development of stability factors for empirical equations and safety factors for analytical equations. To work around these differences, comparisons are made between the two equations by first calculating pillar sizes using the Wilson Equation and then determining the Mark-Bieniawski Equation stability factor for these pillars. Pillars designed using the Wilson Equation were based on site-specific data from 23 mines located in the Americas and Australia. Comparing sizes of pillars designed by the Wilson Equation to the Mark-Bieniawski Equation; the Wilson Equation pillar sizes were smaller in 77% of the cases, similar in 3%, and larger in 20% of the cases.

Jan 1, 2008

By Steve Kral

Despite low commodity prices and mining industry cutbacks throughout the world, Peru remains one of the industry’s bright spots. The country’s remarkable economic turnaround during the 1990s remains a model for other developing nations to follow. And the Peruvian government has not forgotten the industry that was instrumental in that turnaround. True, the country has not been spared the effects of the mining industry’s retrenchment that has occurred in other parts of the world. However, foreign mining companies remain committed to doing business in Peru. And the government remains committed to attracting foreign investment and maintaining a strong mining industry. This commitment was evident in September 1999during the 24th Convention of the Institutos de Ingenieros de Minas del Peru in Arequipa, Peru. More than 3,000 mining industry professionals from around the world attended the convention. And Extemin, the accompanying exhibit, featured more than 450 companies, many from the United States, Canada, Australia, South Africa and other countries.

Jan 1, 2000