Search Documents

By Pradip

The selective adsorption of chemisorbing fatty acids at high temperatures together with the addition of soda ash and lignin sulfonate as depressants is the key to the industrial processing of bastnaesite ores. This paper presents the results of a fundamental investigation that indicate that alkyl hydroxamates can be an alternative collector for the beneficiation of bastnaesite ores that contain barite and calcite as the principal gangue minerals. The primary mechanism for providing sites for the chemisorption of hydroxamate on bastnaesite appears to be through dissolution of cations, formation of the respective hydroxo complexes and readsorption at the interface.

Jan 1, 1989

By Kenneth N. Pike

The need to comply with environmental regulations and increase production has resulted in modifications to the East Penn blast furnace operation. Changes made include furnace design modifications, closed loop water cooling with heat recovery, automated weighing and charging, automated tuyere punching, ammonia scrubbing of tail gases and improved metal and slag handling to minimize environmental impact. These changes have resulted in a marked increase in yearly production and compliance with many of the air, water and solid waste regulations.

Jan 1, 1990

By Di Yang

The influence of high density (104 -105 A/cm2) electric current pulses (70 us duration) and continuous DC (~103 A/cm2) on the flow stress and ductility in tension of a high carbon steel wire were determined at 204°, 427° and 649°C. Electropulsing (100 pulses per second) with an effective current density of 100-200 A/cm2 gave a 10% enhancement in the uniform elongation of the wire at 204°C, but had no effect at 427°C and 649°C. In contrast, continuous DC either had no significant effect on the ductility or gave a decrease. The electropulsing per se decreased the flow stress only slightly at 204° and 427°C, but gave a significant decrease at 649°C. Continuous DC increased the flow stress at all three temperatures. The present results along with those by others suggest that the enhanced ductility by electropulsing and the reduction in flow stress may be further increased by raising the effective current density through increases in either the pulsing frequency, maximum current density of each pulse or pulse duration. This could conceivably increase the reduction per pass during wire drawing or the number of passes between anneals.

Jan 1, 2001

By A. Bruynesteyn

It is well known that most North American gold deposits are of a hydrothermal origin and therefore they are often associated with sulphide minerals such as pyrite and arsenopyrite. When the precious metals in such ores are held captive inside sulphide crystals, the ores are called refractory because they do not respond to treatment by direct cyanidation. In these cases, it is necessary to recover the contained precious metals using high temperature treatments such as smelting or roasting, or high pressure leaching processes to break down the sulphide crystal matrices and thus liberate the precious metals for subsequent extraction by cyanidation. Sulphidic gold ores containing arsenic and/or antimony are considerably more difficult to treat because, in addition to their refractory nature, the arsenic and antimony content also prohibits treatment by direct cyanidation or amalgamation. These ores must be milled and their sulphidic gold values concentrated by flotation. The resultant concentrates must then be roasted to break down the sulphides before cyanide treatment can be applied.

Jan 1, 1985

By David J. Roha

"The harsh environment of the Carbothermic Aluminum process makes necessary numerical modeling as a means of process visualization and understanding. A brief survey of the various numerical models, with emphasis on CFD, applied in the development of the process is presented.IntroductionThe environment of the Alcoa Carbothermic reactor is necessarily a harsh one, with temperatures approaching 2100 °C and plenty of reactive dust and vapors. As such, it is difficult to directly observe what is actually taking place. Thermocouples can last for a few minutes but are eventually destroyed. The openings to optical pyrometers become occluded with dust and condensation. Graphite sheathing embrittles, reacts away or becomes clogged with condensate. Dip-samples on steel rods are routinely taken, but their interpretation is often unclear.Those measurements that can be reliably taken are invaluable, but often do not provide a complete picture. Therefore from the very inception of the project both physical and computer based models have played an important role. Modeling provides an intuitive understanding of the processes that might be taking place and in very many cases approach quantitative prediction. I will briefly touch upon computer-based modeling performed at Alcoa over 12 years of the Carbothermic project, with special emphasis on CFD. The explanation of physical models is perhaps best left for those with the greatest familiarity with them"

Jan 1, 2012

By Anthony C. Mulligan

Metals have historically been used in mining since they offer an excellent combination of hardness, toughness and cost and can be fabricated to form a variety of shapes. However, for many applications the metals used today have limited performance in the environments in which they are needed. This is particularly true for geothermal environments where the brines are highly siliceous causing corrosion and accelerated wear of many components. Geothermal sources are increasingly being explored for their high thermal value as well as possible sources for future minerals. While advanced ceramics have historically been expensive to produce in comparison with metals, they offer significantly greater corrosion resistance and hardness and can improve the overall performance when used in selected ?problem? areas. One of the major drawbacks in the use of ceramics in high impact areas has been their brittle nature and propensity to fracture and spall (fail) when loaded. Recent advances in the fabrication of ceramics have combined hard (strong) ceramics with more ductile ceramics in a architecturally designed microstructure, thus allowing ceramics to perform well in these high impact regions. Additionally, ceramics are significantly more inert to corrosion from either alkaline or acidic environments and can typically be used for significantly longer periods in these environments than their metallic counterparts.

Jan 1, 2006

By Zbigniew Smieszek, Ryszard Chamer, Ryszard Prajsnar, Zygmunt Kurek

"Lead-containing wastes processed at the IMN’s Division in Legnica originate mainly from dry and wet dedusting installations of the technological lines for copper production. These are lead dusts and lead-zinc dusts characterised by the specific properties resulting from the chemical composition of the Polish copper concentrates. Besides lead, they contain many accompanying metals and impurities such as zinc, copper, sulfur, chlorine, potassium, sodium, and also bituminous substances. Processing of lead-containing dusts is conducted in the installations of rotary-rocking furnaces heated with gas-oxygen burners fitted with auxiliary systems for cleaning process gases and refining re-circulating dusts. The processing technology utilizes innovative process and technical solutions enabling disposal of lead-containing wastes from copper metallurgy and from non-ferrous metals industry according to the BAT recommendations and to the guidelines specified in integrated permission. In this paper, the main technological aspects of processing lead-containing dusts at the IMN’s Division in Legnica have been presented.IntroductionCrude lead is obtained in Polish lead metallurgy from various primary and secondary materials, such as Zn-Pb concentrates, lead-bearing dusts of copper metallurgy and battery scrap. In zinc smelter Miasteczko Slaskie S.A. crude lead is produced from sulfide and oxide Pb-Zn concentrates in ISP process. Orzel Bialy S.A. and Baterpol Ltd. produce crude lead in short rotary furnaces in the process of smelting products of mechanical battery scrap separation– desulfurised or not desulfurised paste and metallic fraction. KGHM Polska Miedz S.A. and IMN Divison in Legnica produce crude lead in rotary furnaces in the process of smelting of polymetallic dusts and slimes from copper production processes."

Jan 1, 2008

By Fashina Olugbenga Emmanuel, Ghazali Akeem, Adegbola Adekunle Amos, Omotoyinbo Joseph Ajibade, Olaniran Oladayo

"Modern engineering materials are required to be light weight and corrosion resistant, coupled with high strength and hardness. In this work, Al formed the parent metal and alloyed with 2.03% of Copper by sand casting process. The cast product 2024 was warm worked at various temperatures ranging from 300 to 5600c at 5%, 10%, 15% and 20% deformation respectively and aged accordingly. The results showed that the mechanical properties vis-à-vis hardness, tensile improved with increasing % deformation at a higher temperature. This was due to the progressive close-up of the voids emanated from casting by increasing deformation which is evident from the micrographs. MATLAB was also adopted to generate a model capable of determining the trend of flow of stress at operating temperatures. This was of immense value due to an increasing impact at higher percentage deformation with temperatures. Hence, Al -alloys will find applications in land vehicles, ships, trains, and aircraft, at elevated temperature.INTRODUCTIONThe problem of safe vehicle design with maximum impact energy absorption is a significant subject in structural crash worthiness design [1]. All engineering designs are expected to ensure the safety of users' life. This informed several studies meant to probe the causes of component failures in equipment, vehicles, and aerospace design and decide on appropriate solutions through materials selection techniques. A common example is in the design of crankcases and heads, piston, and cylinder blocks. As with engine blocks, cylinder heads can be made of Cast Iron or Aluminium Alloy. A head made of Aluminium alloy is lighter in weight than if it were made of Cast iron [2]."

Jan 1, 2013

By Chi Ru?an

Sollutions of ammonium chloride, nitrate and sulfate were studied in extraction of rare earths absorbed on a low-grade, kaolilnitic ore recently discovered in southern China. The results of percolation leaching tests and the recovery of the rare-earth values from these solutions are presented.

Jan 1, 1989

By H. Aminian

Copper electrowinning (EW) is an important process in connection with the solvent extraction to produce pure and marketable copper cathodes. A phenomenological model was developed to simulate the copper electrowinning process. The simulator is used to predict the operation of the Mines Gaspe pilot plant electrowinning cells put in operation in 1996. Results confirm the potential of the simulator that would subsequently be used for student training, process optimization and assessing the performances of control strategies.

Jan 1, 1999

By W. Marnette

Norddeutsche Affinerie is the largest West European copper producer with an annual output of more than 350,000 tonnes of refined copper, about half of which is produced from copper concentrates. However, in addition to concentrates, Norddeutsche Affinerie processes secondary raw materials and recycling materials which contain a combination of copper and lead. These materials were previously treated in blast furnaces, a technology which has meanwhile been superseded at NA by the electric furnace process, primarily owing to the necessity of complying with the increasingly stringent requirements for environmental protection.

Jan 1, 1994

By Norihiko Fukatsu

In order to use effectively the previously reported new sensing system for hydrogen and oxygen potentials in molten copper, the criteria of the potentials for getting sound castings have been determined in the laboratory experiment. The copper melt equilibrated with a given hydrogen and an oxygen potential was rapidly quenched in the crucible. The relations between the holding potentials and the gas porosity in the solidified sample were investigated by measuring the density of the sample and microscopic observations. It was found that the defects of the gas porosity became the maximum at the potentials where the dissolved amount of hydrogen and oxygen was in the mole ratio 2: I. The samples having the density more than 99% of the theoretical value were obtained in the higher oxygen and lower hydrogen potential region or in the lower oxygen and higher hydrogen potential region. The criteria thus determined were examined by comparing with the measured potentials in the practical easting machine. In tough-pitch copper casting, the problem due to gas porosity was found to be serious when the hydrogen potential increased. In the oxygen-free copper casting, the evolution of hydrogen was found not avoided. The gas porosity in the casting, however, was found eliminated when the oxygen potential was kept at a low value.

Jan 1, 2003

By Norihiko Fukatsu

In order to use effectively the previously reported new sensing system for hydrogen and oxygen potentials in molten copper, the criteria of the potentials for getting sound castings have been determined in the laboratory experiment. The copper melt equilibrated with a given hydrogen and an oxygen potential was rapidly quenched in the crucible. The relations between the holding potentials and the gas porosity in the solidified sample were investigated by measuring the density of the sample and microscopic observations. It was found that the defects of the gas porosity became the maximum at the potentials where the dissolved amount of hydrogen and oxygen was in the mole ratio 2:1. The samples having the density more than 99% of the theoretieal value were obtained in the higher oxygen and lower hydrogen potential region or in the lower oxygen and higher hydrogen potential region. The criteria thus determined were examined by comparing with the measured potentials in the practical casting machine. In tough-pitch copper casting, the problem due to gas porosity was found to be serious when the hydrogen potential increased. In the. oxygen-free copper casting, the evolution of hydrogen was found not avoided. The gas porosity in the casting, however, was found eliminated when the oxygen potential was kept at a low value.

Jan 1, 2003

By Payal Bakshi, Sangeeta Tiwari, Mohini Saxena, Anusha Sharma

"Recycling and reuse is perhaps the most favorable and beneficial way to solve the problem of industrial waste disposal. However, the use of industrial wastes like fly ash, tailings etc is in practice for brick manufacturing, land filling, embankments filling etc. These existing practices do not add enough value to the wastes. Moreover, some wastes may have very good potential to be incorporated in valuable products like paints. This study reveals about the value addition of industrial wastes like fly ash, copper tailing and blue dust as an extender in paints. Comparative properties and characteristics of these three wastes for application in paints are discussed. Fly ash, copper tailing and blue dust were characterized for physical, chemical and mineralogical properties and used in different paint formulation based on their potential to the particular application. Fly ash has been found very useful in enamel, primers and flat paints while copper tailing was found suitable in oil based paint formulations. The performance of fly ash and copper tailing paints were evaluated by comparing with those of conventional whiting extender. Blue dust was compared with conventional iron oxide for use in priming coats. The extender properties of these new material and paints prepared out of blue dust, fly ash, copper tailing, were found better than the existing related materials.IntroductionIndustrial development and environmental reforms should run parallel to benefit each other. This is the best policy, which must be adopted by industries for the sustainability of the current modern life. The high degree of industrialization and urbanization adds scads of waste resulting problem of pollution and challenges of their safe disposal. The nature of waste depends on the process that produces waste as its by-product. Therefore, policies/plans are prepared by keeping the view of possible potential hazards. Among the different wastes some are generated in the industries, which have great importance in the country’s economy, like fly ash waste from thermal power industry and mining waste. In India the total contribution of thermal power in the total electricity generation is more than 70% and it produces about 123 million ton of the fly ash annually [1]. On the other hand mining plus extraction of ferrous and nonferrous metals also produce waste in million tonnes of categories [2]. Since the generation of this waste is very high they cover large land area for their disposal and dumping [3]. The storage of this waste in the dumping sites for long time duration may cause problem of land, surface water, ground water and fertile soil contamination [4]. As far as Indian fly ash is concerned it does not contain toxic element over the limits of hazardous waste [5]. However, in general most of the metals deposits are found in the form of pyrite based ores. Mining wastes contain toxic elements e.g. heavy metals in varying amount, which get mobilized when pyrite get oxidized to sulphate producing sulphuric acid [6,7]. These ores contain very less amount of targeted metals in themselves thus they require extensive preprocesses for concentration of the metals [8]."

Jan 1, 2008

By Shaolong Chen

Feeding dry sulfide concentrate into smelting furnaces enhances process performance and reduces the energy consumption and exhaust gas flow. Direct heated rotary dryers and flash dryers have being replaced by rotary steam dryers featured by very low wear rate of the pipe heating elements and long maintenance interval. Impact of the drying processes on the environment receives more and more attention as the emission legislation tightens. In this regard, environmental factors such as SO2, CO2, dust and gas flow among rotary dryers, flash dryers and steam dryers were compared. Selection of a rotary steam dryer for copper and nickel concentrate drying would be an ideal solution to reduce the pollution of exhaust gas, as drying is achieved by indirect contact to the steam at relatively low drying temperature and as the off-gas contains almost only water vapor and air. The emissions can be significantly reduced and only small and simple off-gas handling units are needed.

Jan 1, 2006

The increasing need for robust pyrometallurgical furnace construction is driven by two trends in the copper and other base metals smelting industry: ? the desire for increased production within a single furnace line by greatly increasing smelting intensities, which generates high heat fluxes to the crucible. walls, and ? the operational and economic imperatives of maintaining high percentage on- line times and long campaign lives between rebuilds. A key feature of furnaces capable of producing at high rates, while containing intense processes, is a strong, thermally robust wall cooling system. Equally important design aspects include the furnace steel structure, refractories, a cooling water supply and piping arrangment for safety from leaks and disruptions, and instrumentation/controls for monitoring and rapid mitigation of process excursions. Integration of the cooling elements into these furnace systems is essential for optimum performance of the cooling elements, and indeed the entire furnace. This paper discusses the development of a composite copper / refractory water- cooled design, which has been successfully implemented on several copper smelting and converting furnaces, including Kennecott's flash converting furnace, INCO's MK reactor, and Kidd Creek's converting furnace.

Jan 1, 1999

By Elsa Olivetti, Randolph Kirchain, Gabrielle Gaustad

"As scrap usage increases, it is often necessary to “dilute” the melt with primary aluminum to ensure the finished product meets compositional specifications. Secondary raw materials, particularly postconsumer scraps, often include high levels of unwanted or “tramp” elements, such as iron and silicon in the case of aluminum. Recent literature on this issue cites several causes including inherent contamination during processing as well as ineffective segmentation at end-of-life. To address this accumulation problem, “upgrading” solutions have been developed including: dismantling of end-of-life products, spectrographic or magnetic sorting of shredded scrap, and “filtration” technologies that remove tramp elements in the melt. Although it is clear that upgrading strategies enable increased usage of scrap, it is not clear that they would be economic or efficient. This work presents a set of analytical methods, based on chance constrained optimization, to quantify the potential environmental and economic value of several scrap upgrading technologies.IntroductionAluminum recycling has a number of key environmental and economic benefits. Compared to other materials, aluminum production has one of the largest energy differences between primary and secondary production: 175 MJ/kg for primary compared to 10-20 MJ/kg for secondary[1]. With energy and cost savings in mind, many producers now have targets of increasing their usage of secondary materials[2, 3]. However, the accumulation of impurities in these recycled material streams provides a significant compositional barrier to these goals[4].A growing number of studies and literature would suggest that accumulation of unwanted elements is a growing problem, in all recycled material streams. In the case of aluminum, the list of problematic impurities is quite large, including but not limited to: Si[5, 6], Mg, Ni, Zn, Pb, Cr[7], Fe[5-7], Cu[6, 7], V, and Mn[6]. Metals recycling is a metallurgical process and is therefore governed by the laws of thermodynamics. The removal of unwanted elements in the scrap stream is dictated by the energy considerations of the melt process. Compared to many metals, aluminum has a high degree of difficulty in the removal of tramp elements, due to thermodynamic barriers. Therefore, with no simple thermodynamic solution, producers must identify strategies through-out the production process to mitigate this elemental accumulation."

Jan 1, 2008

By Nicola Baldo, Marco Pasetto

"The paper discusses the results of a laboratory study, aimed to evaluate the suitability of the bottom ash from Municipal Solid Waste Incineration (MSWI), obtained from different Italian plants, to be recycled in the lithic skeleton of bituminous mixtures, for base layers of road and airport pavements. The research involved a preliminary study of the physical and geotechnical properties of the bottom ash by itself; it was followed by a mechanical characterization of the bituminous concretes. The traditional Marshall methodology was used to identify the optimum bitumen content; the mixtures were also mechanically checked by means of the stiffness modulus test, repeated load axial test and fatigue test. Because the requisites for acceptance in the Italian Specifications and Standards have been satisfied and given the positive mechanical performances, it has been verified that the MSWI bottom ash can be used as substitution of the lithic materials in the road bases, also with very high contents (up to 81% on the weight of the aggregate). Introduction The incineration of Municipal Solid Wastes (MSWs) provides for by-products which can be mainly classified as bottom ash and fly ash. The first one, corresponding to the 25% on the weight of the wastes to be incinerated, so resulting the principal product of the process, is mainly composed by Silica (Si), Iron (Fe), Calcium (Ca), Aluminium (Al), Sodium (Na) and Potassium (K) oxides, so presenting a composition similar to that of different natural materials. Its metallic fraction can be recovered; the remaining part is usually stocked in dumping or, less frequently, recycled. Bottom ash can be re-utilised in the construction of new infrastructures, especially in bitumen bounded mixtures, because of the inert properties of the binder which covers the grains with a subtle film, that prevents the release of heavy metals. The paper describes a study aimed to design new bituminous mixes for flexible road and airport pavements, realised with the highest content of 4 types of bottom ashes, deriving from different MSWI plants of the Northern Italy. The ashes will be named as BA1, BA2, BA3, BA4 respectively (the origin cannot be specified)."

Jan 1, 2008

By Xingming Zhang, Huawei Zhang, Yanxiang Li

"A hybrid porous metal with nano-micro double scale pore size and regular-random bimodal porous structure has been fabricated by unidirectional solidification of a lotus-type alloy followed by dealloying treatment to the base alloy. The base alloy selected is a Cu-Mn binary alloy. The lotus-type porous Cu-Mn alloy with straight pores of several hundred micrometers in diameter was manufactured by unidirectional solidification with a mould casting process. Dealloying treatment was then done to the lotus-type porous structure of Cu-Mn alloy. The solid Cu-Mn alloy wall of the lotus-type porous structure was transformed to random porous structure of dozens to hundreds nanometers. The influence of corrosion parameters, such as the current and time in electrochemical corrosion, temperature and corrosion agent in chemical corrosion, on the nano-porous structure formed has been studied systematically.1. IntroductionA hybrid porous metal is a kind of cellular structure with different porous or cellular forms inside, which possesses special properties and can be applied in many fields as fuel cells, catalysis, sensors, etc. Several means have been developed to fabricate this kind of porous material [1-2]. In this paper, a novel process of Gasar plus dealloying is introduced to fabricate a new form of hybrid porous metal with nano-micro double size and regular-random bimodal structure.The Gasar process, also called the metal-gas eutectic directional solidification, that invented by Shapovalov [3] in Ukraine and now in USA some twenty years ago, is used to fabricate porous metals with regularly aligned pores basing on the solubility difference of a gaseous element in solid and liquid metal. Nakajima and his colleagues [4] in Japan studied this process further and called this kind of structure a lotus-type porous metal. They put more attention to various fabrication techniques and properties of lotus-type porous metals. Li heading a group [5-6] in P.R. China studied the mechanism of Gasar process and process controlling techniques. The Gasar pore structure and porosity can be controlled by processing parameters, and a regular Gasar structure with oriented pores distributing uniformly in the solid matrix can be obtained under optimized processing parameters."

Jan 1, 2014

By M. J. Soria-Aguilar, F. R. Carrillo-Pedroza, S. Preciado-Nuñez

"Dust originated from the Iron Blast Furnace (BF) and the Basic Oxygen Furnace (BOF) containing alkalis and zinc are not completely recycled because due affects the process efficiency. These types of dust represents an economical lost as a consequence of values contents of iron and carbon. Several processes in aqueous media have been developed to treat the steelmaking dust. This work presents a laboratory study for reduce zinc and alkali containing in BF and BOF dust, using different acid and alkaline solutions and oxidants as ozone. The results obtained show that the elimination of zinc and alkalis can vary from 5 % to 80 % depending on the treatment conditions (the solution, the oxidant and the temperature). The dust obtained from this treatment can to be recycling to the steelmaking processes to recovery iron and carbon values.IntroductionEach one of the steel making industry processes generate several sub-products and residues containing useful units of iron, carbon and other elements that are or could be recycled to the productive process. Some of those sub products are the dust from the gas cleaning system of the blast furnace and the dust from BOF reductive process; such dusts are sent to the sedimentary lagoons. The dust represent a lost of 2 % of the total iron and coal mineral’s content feed to the process.The typical iron, carbon and zinc content of the blast furnace dust is approximately 40, 24 and 0.3 % and the content of the BOF dust are 50, 15 and 0.9 % weight respectively, with physics - chemical characteristics that became them susceptible to be agglomerated and feed to the blast furnace. But the high content of zinc does not allow recycling it into the process. At the blast furnace the presence of zinc propitiate the formation of film in the furnace wall; these elements are vaporized in the low section of the cube of the furnace and they are dragged by the gases to the top and condensed again at the cube. Part of these condensed materials strongly adheres to the furnace cover harming it and reducing the empty space of that section, causing eventually a severe perturbation of the ascendant gas flux [1]."

Jan 1, 2008