Search Documents

By A. G. Jackson, Rand R. Biggers, John D. Busbee, Iman Maartense, David P. Lubbers, David C. Liptak

"This paper describes the application of Raman Spectroscopy for characterizing superconducting YBCO thin film parameters. Attenuation of the substrate Raman spectrum as a function of material deposited is established. Also a correlation between film quality and Raman spectrum is explored. The identification and discrimination of superconducting and non-superconducting phases of YBCO is presented. The critical temperature (Tc) of a film as a function of its oxygen content is also established using Raman peak ratios. These results provide significant implications toward the use of Raman Spectroscopy for in situ monitoring and control of the PLD process. Film quality can be controlled via optimization of film oxygen content and reduction of improper YBCO phases. Film thickness can be controlled by monitoring the response of the substrate material. Also the PLD process can be studied and modeled using this powerful observation tool.IntroductionSuperconductors are materials that possess unique characteristics when cooled to sufficiently low temperatures. Below a material's critical temperature (Tc) it exhibits zero resistance to current flow. One such material, yttrium barium copper oxide (YBCO) has a critical temperature of approximately 92° K. Due to its high critical temperature YBCO is being aggressively researched for many possible applications, because of high current carrying capability and strong pinning of flux lines.YBCO in the 123 form is a ceramic material that was discovered in February, 1987. Its unit cell structure is shown in Figure 1 [ 1,2]."

Jan 1, 1997

By Robert W. Hyers

Electromagnetic levitation has proven important in a wide range of experiments, all affected by fluid flow. For some experiments such as viscosity measurements, only whether the flow is laminar or turbulent must be established. For other experiments, however, quantitative assessments of velocity, shear stress, or shear strain rate are required. In most cases it is difficult or impossible to measure the internal flow in levitated droplets directly. The samples are usually small, opaque, reactive, high-temperature, metastable, or all of these. Furthermore, recirculating flow limits the utility of tracking surface particles, since they collect in stagnation points ratherthan following the flow. Most research groups have chosen mathematical modeling to assess the internal flow in levitated droplets. A variety of analytical and numerical methods have been applied, including both laminar flow and various turbulence models. A number of these models are reviewed and their impact on different containerless experiments is assessed. Much of the research reviewed here was performed by alumni of Professor Julian Szekely, and by others using similar methods.

Jan 1, 2006

By Lijuan Li, Zheng Lu, Xin Xia, Qijie Zhai, Qingchun Li

"Pulsed current and pulsed magnetic field have been applied to the bainite transformation of Cr5 steel. Three groups of experiments were conducted. In the first group, ordinary resistance furnace was used for heat treatment. The Cr5 specimens were rapidly heated up to austenitization temperature 940 °C, held for 20 min, air cooled to bainite transformation temperature 350 °C, held for 10, 20, or 40 min and then air cooled to room temperature. The second and the third group shared the same temperature-time curve with that of the first group, but their heat resources came from the Joule heat produced by pulsed current. 1.5 T pulsed magnetic field was exerted on the third group specimens when they were held at 350 °C, but the second group specimens did not undergo the treatment of magnetic field. It was found that both pulsed current and pulsed magnetic field obviously retarded the bainite transformation. The phenomena were discussed in terms ofliterature results.IntroductionApplying pulsed current and pulsed magnetic field technology are very pronnsmg ways to change the microstructure of materials by affecting the phase transformation process. People had found that pulsed current dramatically influences the behaviors of materials, for example, electromigration effect [l], the solidification of metals and alloys [2, 3], electroplasticity [4, 5], crystallization of amorphous alloys [6], healing of metal materials [7] and so on. As to pulsed magnetic field technology, a lot of effort had been spent on grain refinement in solidification of metals [8, 9], recrystallization of cold-worked metals and alloys [10] and Fe-based alloys solid-state phase transformation [11, 12]. Though application of pulsed current and pulsed magnetic field technology have proliferated in recent years, investigation on their effects on solid/solid phase transformation, especially bainite transformation, is lacking. The aim of this paper is to show the effects of pulsed current treatment (C-T) and the combined treatment of pulsed current and pulsed magnetic field (CM-T) on bainite transformation of commercial Cr5 steel"

Jan 1, 2014

By Markus A. Reuter, Antoinette van Schaik

"Product design engineers select from a wide range of materials and combine them into multimaterial product designs. These include various materials (metals and non-metals) which are complexly integrated (e.g. welded, glued, alloyed, layered). The recycling/recovery rate of consumer products are determined by the different materials and alloys used, but also by the particle size and multi-material particle composition after shredding (combination of materials due to design). Eco-design (for recycling) and Design for Recycling (DfR) can only be conducted if the interconnectivity of material/metal in various unliberated materials is accounted for and its effect on material and energy recovery can be linked back to design. This paper will discuss the basic principles of these DfR models and it is shown how these tools (i) are linked Computer Aided Design (CAD) and Life Cycle Assessment (LCA) software, (ii) affect conceptual design specifications of products, (iii) integrate the complex detail of the recycling system and recyclate quality and hence (iv) make recycling an integrated part of the product system. Furthermore, it is shown how these assessment tools and models can be applied for benchmarking of the recyclability and environmental damage created by the recycling of end-oflife consumer goods in order to e.g. (i) provide the (original) equipment manufacturer with knowledge and solutions to support product stewardship and Extended Producer Responsibility; (ii) create awareness of the consequences/benefits of design, products and recycling systems to manufacturer, designer, legislator, recycler etc.; and (iii) assist the consumer in their choice of consumer goods from an end-of-life point of view.IntroductionA first-principles basis is required in order to be able to simulate and predict the recycling/recovery behaviour of products facilitating Design for Recycling (DfR) and Eco- Design. This links recycling technology and the environmental consequences of recycling directly to product design."

Jan 1, 2008

By Guillermo Rios, Arbizum Cristina, Joa Viflals, Alba Sunyer

"Atlantic Copper is one of the largest copper producers in Europe. Its production facilities are located in Huelva (Spain) and account for the smelting of over one million tpy of concentrates to produce up to 260 ktpy cathodes and 900 ktpy of sulphuric acid. During copper concentrate smelting, the slag coming from the flash furnace and PS converters are treated in an electrical slag cleaning furnace. As a result of the treatment of the off gases from this furnace, approximately 2,000 tpy of a Zn-rich filter cake are produced and are sent to authorized waste managers. This paper describes the characterization of this material and the preliminary results of a new process to recover zinc as a pure zinc hydroxycarbonate while lead is collected as an indium-rich anglesite product. The behavior of impurities (Cd, As, Tl, Sn, Sb, Bi, Cu, Se, Te) in the leaching, solution purification and precipitation steps is also reported.IntroductionThe Atlantic Copper Metallurgical Complex in Huelva (Spain) was commissioned in 1970 with a capacity of 40,000 tpy of copper from concentrate. In 1975, the old blast furnaces were replaced by Outokumpu flash smelting furnace (FSF) technology, and the copper refinery capacity was increased to 108,000 tpy. Between 1994 and 1996, an expansion project was carried out to increase the copper from concentrate and cathodes to 250,000 tpy and 215,000 tpy, respectively. This expansion basically consisted of a new sulphuric acid plant, replacement of the anode furnaces by two 400 t units, redesign of the slag cleaning furnace (SCF), an increase in the electrolytic cells to 1,120 and implementation of ISA permanent cathode technology. Furthermore, a debottlenecking project has led to a capacity of 1,000,000 tpy of fresh concentrate since 1997. Meanwhile between 1995 and 1998, a cathode production rate of 260,000 tpy was reached as a result of a progressive increase in the current density in the refinery."

Jan 1, 2012

By A. G. Raraz

Reactive metal electrorefining presents a number of problems that pose obstacles to commercial operation. Cerium has been chosen as the surrogate for certain reactive metals because of its thermodynamic and electrochemical characteristics. A comparative review of the properties for cerium and plutonium has been presented to justify the choice of cerium as the surrogate metal for studying electrorefining. This review has addressed the electrochemical, thermodynamic, and kinetic parameters of molten salt electrorefining of cerium metal to provide an insight to this extremely important process. The cell components and configuration, current efficiency of the process, purity of the cathodically deposited metal and the power requirement of the system are evaluated for a molten CaCl2-MgCl2 salt electrolyte using a molten, stirred impure anode. Crucible designs, salt electrolyte, cell temperature and electrode materials are also evaluated. Selection of the salt electrolyte and the cell temperature have been suggested from this study.

Jan 1, 1992

By P. M. Pincheira Brown

The widely accepted inverse relationship between copper prices ail stocks, has been commonly used by analysts to explain the behavior of the copper market and to forecast film copper pries. However, empirical data have not shown such a clear relationship between copper prices and stacks. Existing evidence only indicates a weak tong-nut relationship that vanishes in some periods. In this paper a simple comprehensive model is provided which explains both parallel and opposite direction movements between prices and stocks. Former are explained mainly by stocks demand expansions-contractions while the latter are in essence due to increases in the supply curve. Furthermore, econometric estimations are provided, thus giving a powerful tool to forecast and explain price developments of the copper market.

Jan 1, 1999

By Takamasa Ishigaki, Gervais Soucy, Mohamed Rahmane

"The induction plasma jets employed for the in-flight nitridation of molybdenum disilicide (MoSi2) powders were investigated in terms of their flow characteristics. The present study shows the effect of the operating parameters of the plasma torch, as used for this process, on the plasma jet properties. The enthalpy probe techniques, along with mass spectrometry, were employed for the measurement of the jet temperature, velocity and concentration fields. The measured values were compared to the results of a numerical simulation performed on the plasma flowing inside the torch-reactor system. The process operating conditions studied were the plasma plate power, chamber pressure and sheath gas composition. The optimal conditions for effecting the nitridation process using thermal plasma are obtained at moderate plasma plate power, at around atmospheric pressure and by using a mixture of argon and nitrogen as the plasma torch sheath gas.IntroductionMolybdenum disilicide (MoSi2) based composites are considered to be one of the most promising candidates for high temperature structural material applications [!], especially because of their high melting points, good oxidation resistance and relatively low cost. However, the wide application of these composite materials is still limited by some factors such as their brittleness at room temperature and lower strength at high temperature (> 1500 K). To overcome such limitations, a number of researchers [2-4] have earlier studied various kinds of reinforcements for MoSi2, e.g. oxides, silicides and nitrides. More recently, Fan and coworkers [5-9] have demonstrated the possibility of in-flight nitridation and carburization of MoSi2, using a thermal plasma process. This work has confirmed the plasma synthesis route as one of the most promising methods for creating an in-situ second phase structure. Properties of the plasma flow, such as its temperature, flow velocity and composition, are of crucial importance for the nitridation of MoSi2 powders during their flight in the plasma. Therefore, the optimization of such a process involving plasma· generated reactive species necessitates a thorough understanding of the plasma flow characteristics."

Jan 1, 2000

By Ronald J. Roman

The shrinking core model for coarse particle leaching has been generally accepted as describing the leaching of a copper oxide or sulfide ore. However, when a mixed oxide/sulfide ore-is leached this model can not be used in its simple form because at least two and possibly three separate leaching processes are occurring simultaneously (dissolution of oxide copper minerals, secondary copper minerals and primarily copper minerals). It has been impossible to isolate their individual leaching curves from the recovery/time curve generated by the column leach test. This paper describes a tests program carried out at the Groupo Mexico, Mexicana de Cobre's La Caridad operation in which the individual recovery/time curves for the leaching of copper oxide mineral, secondary copper mineral and primary copper minerals were developed from standard column leach tests. Once the individual recovery/time curves were developed scale-up of the column leach test results to the commercial heap leaching operation is possible by using the shrinking core model.

Jan 1, 1999

By Ron H. Schonewille

Experiments were conducted by injecting air-oxygen gas mixtures through a ceramic lance into molten copper matte and measuring the sulphur dioxide content of the offgas. The injection conditions were characterized by measuring pressure fluctuations immediately upstream of the lance and capturing the information on an oscilloscope screen. The parameters investigated were gas flowrate, lance geometry, lance immersion, orifice diameter and melt composition. An overhead nitrogen lance was used in specific tests to create an inert gas blanket directly above the bath surface to inhibit reaction in this region. The extent of oxidation was modeled by separating the gas-liquid contact into three stages; bubble growth, bubble rise and bubble rupture. The contribution of each stage to oxygen utilization was determined by varying the lance immersion and by performing tests both with and without an inert gas blanket. Bubble rise was found to be relatively unimportant, accounting for less than 5% of the total oxygen utilization. Bubble rupture and bubble growth were found to contribute approximately equally, with bubble rupture becoming more important with increasing gas flow rate. This study highlights the importance of reactions taking place above the bath surface in a copper converter.

Jan 1, 1999

By H. Virtanen

Outokumpu copper refining operations have a long history of expansions and application of new technologies. Outokumpu is a name known around the world for technological excellence in the field of base metals, and part of the policy of operations is continuous investment and investigation in new technologies. The results of this hard work sometimes are immediate and sometimes take years. The work done during the last years at the Outokumpu Harjavalta Metals copper refinery, together with a sister technology group Outokumpu Wenmec, has started to bear fruit in terms of the following radical developments and advances that are and will be applied to assure Outokumpu's position as the technology leader and a low cost and safe producer. Some of the developments discussed include the new anode and cathode design, mechanised electrode handling, cell design incorporating features facilitating full automation, automated short circuit detection and removal, automated on line anode slime removal, and high efficiency and intensity refining.

Jan 1, 1999

By Pranav Deshpande

The wear behavior of metal matrix composites differs from that of the monolithic metallic counterparts because composite materials have multiple constituents in their structures and these constituents wear at different rates. It was observed that under low wear stresses, abrasive wear prevailed. As the wear stress increases, pullout of reinforcement occurs and both abrasive wear and wear due to pullout contribute to the overall composite wear. A model of wear taking into account both types of wear has been developed. A critical pullout wear stress was suggested for each composite. Below the critical wear stress, no pullout of reinforcement occurs. It turns out that the critical wear stress simply equals to the ratio of the interfacial strength between the matrix and the reinforcement to the friction coefficient between the reinforcement and the wear counter surface. The critical wear stress is independent of the particle size of the reinforcement. From data on wear of 53% WC composites, the equation of wear for 32% WC composites was obtained. Experimental results agreed well with the predicted wear rate of this composites. This provides an excellent verification of the wear model developed by Lin and Deshpande. Wear data from Modi et al. in the literature were also perfectly fitted with the model.

Jan 1, 2006

By Reza Rahimi, M. Nili Ahmadabadi

"Because of high cost and shortage of primary resources of Ni-base superalloys, revert alloys can be used as a part of charging materials for production of superalloys ingots. The current study is based on recycling of IN738LC, a Ni-base superalloy, using 30% and 50% reverted alloy and balanced amount of virgin raw materials. Therefore, it has been attempted to cast an alloy with references to standard chemical composition and mechanical properties. After charging and casting in vacuum melting furnaces, chemical composition verification and non-destructive tests (i.e. Penetration and Radiography Tests), quality of samples were evaluated at elevated temperature by stress-rupture test. Results acquired from chemical composition and mechanical test indicate that cast ingots using 30% and 50% reverted alloy is reliable and consistent with the quality control requirements.IntroductionIn recent years, there have been many fluctuations in cost and availability of raw materials which are extremely determining in Ni-base superalloys production. Accessibility to the high purity metals such as Cobalt, Molybdenum, Tantalum, Niobium and etc. have been problematical during the past decades. Therefore, shortages of critical raw materials beside the economical considerations motivated the alloy suppliers and investigators to study and find alternate sources such as reclamation and recycling of scraps [1].There are a lot of reasons for the necessity of recycling; perhaps the most justifiable one is that consumers themselves produce scraps. For example, the weight of a finished superalloy product could be less than one-third of the cast alloy weight and in the case of complicated machined parts; this portion may reach to one-tenth [2]. High values of constituents, reduction of energy consumption and environmental concerns have all strengthened the obligation of recycling in Ni-base superalloys.Because of the high degree of risk in usage of improper materials for production of turbine blades, a delicately controlled program for recycling is needed. Depending on the type of scraps, this program can define the recycling procedure, required instruments, allowable percentage of scrap for usage and finally confidence level of the process."

Jan 1, 2012

By Stuart D. Miller, Clayton L. Rumble

"A field net acid generation (NAG) test procedure has been utilized on-site to identify, classify and map potentially acid forming overburden at the PT Kaltim Prima Coal (K.PC) mining operation situated in the tropical equatorial region of East Kalimantan, Indonesia. The field procedure involves routine use of a calibrated, site specific NAG test (rapid oxidation test using hydrogen peroxide) which has a tum-around time of less than 24 hours and requires minimal sample preparation. It is used on geological drill-hole samples, for forward planning and overburden management; blast-hole samples, for day-to-day operational control and overburden scheduling; and final dump surface samples, for verification testing. This operational monitoring program has been in use at KPC for the past four years.Calibration and implementation of the field procedure has involved validating the NAG test using conventional acid-base accounting techniques, producing an overburden geochemical classification scheme, optimizing laboratory and sample preparation procedures, and ongoing quality management. This paper presents background theory and practical application in a case study format."

Jan 1, 1999

By T. Gunawansa, T. L. Alford, Zhao Zhao, A. R. Lanz, N. David Theodore

Many sustainability issues arise during the manufacturing processes that are currently used for solar cells. Solar energy is a renewable energy source that is independent of the earth’s resources, and it is therefore important for the development of more sustainable technologies. Microwave annealing (MW) has been proposed as a technically feasible fabrication scheme for large area silicon solar cells. Apart from that, microwave annealing has been demonstrated to be a promising alternative for repairing damage and electrically activating dopants in ion-implanted semiconductors for integrated circuit manufacturing. A microwave oven is cheaper than conventional furnace systems. In addition, microwave heating is much more efficient than conventional furnace heating, as heating is directly produced inside the material. This minimizes the loss of energy due to heating of the ambient. There is a need for more efficient processing techniques. In this study, microwave annealing is used as an alternative to the current postimplantation processing. Arsenic-doped silicon was microwave annealed (with an aluminacoated silicon carbide susceptor) to activate dopant atoms and to repair damage that was caused by ion implantation. Sheet resistance and Hall effect measurements were used to assess the extent of dopant activation. Rutherford backscattering spectrometry (RBS) with ion channeling was conducted to determine the extent of recrystallization. The dopant activation and recrystallization resulting from microwave annealing is compared with that resulting from conventional rapid thermal annealing (RTA) with the same heating profile. The results show that when compared to RTA, susceptor-assisted microwave annealing results in better dopant activation for shorter anneal times under the same heating conditions.

Jan 1, 2015

By Julien Favre, Akihiko Chiba, Damien Fabregue, Yuichiro Koizumi, Eric Maire

"The mechanical behavior of Co-20Cr-15W-10Ni alloy is studied by compression tests at high temperature. Microstructures after deformation are evaluated using SEM-EBSD. Significant grain refinement occurs by dynamic recrystallization for high temperature and low strain rate (T>1100°C, <0.1s-1), and at high strain rate (~10s-1). Dynamic recrystallization is discontinuous and occurs by grain boundaries nucleation, leading to a necklace structure. The nucleation mechanism is most likely to be bulging of grain boundaries. However, recrystallization occurs also by rotation of annealing twins which can bulge as well. The modeling of mechanical behavior gives a fair quantification of flow softening due to dynamic recrystallization, indicating the progress of dynamic recrystallization with deformation.IntroductionCobalt-chromium alloys are used in biomedical applications for the elaboration of implants due to their outstanding mechanical properties and their high resistance to corrosion. For stent application a large ductile behavior is required in addition to the high mechanical strength. Indeed stents have to undergo a deformation until e˜40% during their expansion [1]. Conventional Co-Cr-Mo (CCM) alloys exhibit limited ductility (maximal deformation about e˜30%) [2]. Co-Cr-W-Ni (L-605) alloy is a better candidate for stent elaboration since its fracture strain can exceed 40% (comparable to nickel superalloys (Figure 1), while it keeps high mechanical strength. In spite of the presence of nickel element in this alloy, biocompatibility is sufficient for vascular implants, therefore L-605 alloy is extensively used for heart valves and stent elaboration [3]."

Jan 1, 2012

By Larry M. Southwick

The smelting of copper and other non-ferrous metals have made considerable advances over the last 125 years. Many of the ideas and processes currently in use were attempted early in the history of smelting and were unsuccessful. Often the cause was incomplete understanding of the metallurgy involved, inadequate refractories, poor materials of equipment fabrication or trying too many new ideas at once. With time, these problems get solved and the technologies become commercialized .These were processes whose time had not come when originally proposed, but did eventually. On the other hand, there have been some concepts whose time will never come. They were impossible then and they are impossible now. The people that dream these up were either crackpots (they didn&apos;t know what they were doing, but thought they did), or charlatans (they knew they didn&apos;t know what they were doing, but didn&apos;t care). Both rely on bad science to propose metallurgical absurdities. These too have their place in the development of technology, though mostly negative, and several examples will be discussed in this paper. Three from around the turn of the century will be covered, as well as one from this decade. The last demonstrates that the art of creating absurdities has not withered, even after ninety years of scientific sophistication, and some can even be patented. The first three reached field trials due to the gullibility of company management. The last arose from a fortuitous mis-operation of a plant which solved a problem, but the explanation and patent which arose are metallurgically impossible.

Jan 1, 1999

By William Bourcier

Geothermal Brines are a significant potential source of valuable minerals and metals. These brines are water that is heated by the natural heat flow from the depths of the earth. Hotter brines, typically with temperatures greater than 120°C, are used to generate electricity. Lower temperature brines are directly used to supply thermal energy to applications such as agriculture, aquaculture and process/domestic heat. The geothermal waters have had intimate and lengthy contact with the layers of the earth?s crust that they flow through, resulting in dissolution of minerals and metals from the rocks, and solution into the hot water. These aqueous solutions can be processed to recover minerals and metals. Some potential products include silica, zinc and lithium, along with other materials. Recovery of minerals and metals from geothermal brines can be viewed as ?solution mining by nature?, followed by application of known or new hydrometallurgical techniques for isolation and purification. This paper discusses the opportunities, the processes, the challenges, the current status, the economics and the potential for recovery of minerals and metals from geothermal brines.

Jan 1, 2006

By Ramiro Escudero

Michoacan?s beach sands with interesting concentrations of ilmenite were studied to produce titanium by hydrometallurgical techniques. Nevertheless, among titanium species, there are different additional components of Michoacan?s beach sands which could be of interesting applications. Some of them are likely to be applied for the manufacture of nanocrystalline ceramics. Although, the most applied mineral dressing to treat these kind of sands, that contain magnetic species (i.e., ilmenite, magnetite), is a combination of gravity separation and magnetic separation, it could be of a great deal of benefit to apply the information regarding the surface characteristics of the sands? components, in order to study the application of flotation technologies to separate selectively those species with commercial value.

Jan 1, 2006

By V. M. Paretsky

Recent developments made in the Gintsvetmet Institute in the field of autogenous smelting processes have confirmed that autogenous smelting continues to be the main prospective technology for pyrometallurgical processing of sulfide raw materials. This technology ensures energy conservation and environmental safety conforming to the current world standards for production of heavy non-ferrous metals. Two alternative processes of single-stage autogenous smelting producing white metal as well as high-basic ferrite-calcium slags have been developed and can be recommended for technical modernization of Russian copper smelters.

Jan 1, 2002