Search Documents

By C. D. Seybert, J. W. Evans

"The elimination of convection is essential in experimental investigations of diffusive transport (of heat and matter) during solidification. This paper describes an investigation of an approach whereby a magnetic field gradient is applied to a electrically non-conducting diamagnetic liquid. A magnetic body force then arises which is dependent on the volume susceptibility of the liquid and thereby on the density. With the field gradient aligned vertically and of correct magnitude, the variation of gravitational body forces due to density variations (arising from temperature variations, for example) can be counterbalanced by a variation in magnetic body force.Preparatory to a study of convection control in diamagnetic liquids, PN measurements have been made of the convection occurring during the solidification of water. A peculiar flow arises because of the density maximum at 4°C. Modeling of the flow the steady-state solidification of water in an extremely high field magnet at the NHMFL indicates that flow can be significantly reduced, but it is suggested that, due to field gradient variations within the cell, flow cannot be completely halted. INTRODUCTIONNatural convection is inherently a part of terrestrial solidification. Density-based convection during solidification, due to gradients of temperature and/or concentration, has a significant effect on a material's properties. The design of products with specific material characteristics has required the development of many processes to control convection (such as in the growth of semiconductor crystals, and electromagnetic stirring in steel casting). The expansion of fundamental knowledge about the process of solidification requires collecting data in the absence of density-based convection, while most of science's solidification data (and thus the equations that science has fitted to those data) have been obtained under the influence of gravity. Only relatively recently, through clever experimental design (e.g., drop towers, high altitude parabolic flights, and space laboratories), have investigators been able to study solidification in an environment with ""micro-gravity""."

Jan 1, 2001

By Dachun Liu, Yifu Li, Baoqiang Xu, Yongnian Dai, Bin Yang

"The removal of impurity arsenic from crude tin is one of the major problems in the process of tin refining. Through a thermodynamic analysis on vacuum refining process of crude tin, the vapor pressure of impurity arsenic under different temperatures can be obtained, which demonstrates that it is possible to separate tin and arsenic by the vacuum refining process. This paper attempts to verify the behaviors of impurity arsenic. The experiment result shows that through vacuum distillation, crude tin with 0.16% arsenic can be refined from crude tin with 0.96% arsenic, and about 50% impurity arsenic can be collected in the form of metallic arsenic.PrefaceThe crude tin obtained by the reduction process is insufficiently pure for most applications, even smelting from tin concentrate. Arsenic is a common impurity in crude tin and also one of the predominant elements to affect tin performance. Arsenic is a poisonous metal that has long been linked to an increased risk of cancers, diabetes, thickening of the skin, diseases of the liver and digestive complications, so there is a mandatory limit on the amount of arsenic (<0.015%) in tinfoil wrapper and tin layers for food packaging. Arsenic causes a poor appearance and plasticity, and increases viscosity. The impurities content of crude tin fluctuate over a wide range; a lot depends on composition of tin ore concentrate, treatment method and technological process before reduction smelting. And the content range of arsenic is usually 0.5~4%, but it is higher in some factories."

Jan 1, 2012

By S. B. Breyner, A. Ressler, D. Gregurek, A. Spanring

"The changes in process conditions that frequently decrease the service life of refractory products provided incentive for RHI AG to develop high performance bricks, especially for non-ferrous metal applications. Innovative product development was required to determine suitable refractory products for improving lining life. At the Technology Center in Leoben, Austria, practical corrosion testing methods and facilities, including an induction furnace and rotary kiln, enable detailed comparative analysis of brick wear on a pilot scale. In tests that were carried out using a fayalite type slag, the newly developed RADEX VFG magnesia-chromite grade showed very promising results compared to the standard grades. Based on the test results, optimal refractory solutions can be recommended for this challenging industrial application and field trials can be performed directly at the customer's site.IntroductionThe complexity of metallurgical processes in the non-ferrous metal industry, and especially changes to the process conditions in combination with the diversity of metal processing furnaces ''', requires a precise understanding of each individual system for appropriate refractory product selection l2'. In addition, particular importance is focused on the specific refractory consumption being as low as possible.Another important aspect results from the global shortage of resources, which forces companies to invest in recycling processes. In the base metal industry, recycling operations have resulted in significant changes; for example, operating with two slag chemistries and process temperatures will influence the performance of previously suitable linings. The raw material mix for primary smelters has also changed, including higher levels of secondary raw materials in the smelter feed."

Jan 1, 2012

By F. Chabchoub

A mathematical model has been developed to study the influence of process variables on the horizontal Ohno continuous casting process. The model simulates the heat transfer and fluid flow in a wide plate ingot of pure tin. A two dimensional numerical analysis based on a control-volume finite difference approach, the Semi-Implicit Method for Pressure-Linked Equations algorithm (SIMPLER), and an Enthalpy Transforming Model was used. The shape and position of the solid-liquid interface were calculated at different casting speeds, ingot thicknesses, and cooling device characteristics, as well as various mould temperatures. Results of the mathematical model were compared with

Jan 1, 1992

By J. W. A. Morris

To investigate the use of centrifugal fields in fused salt electrowinning cells, a high temperature rig has been designed, constructed and commissioned. Initially, the cell has been applied to the fused salt electrowinning of zinc. Current efficiencies of 93% have been obtained for inter electrode gaps as small as 8mm for 70mm diameter electrodes rotating at 100rpm. The construction of a semi-rigorous physical model has shown the potential exists to extend the use of centrifugal fields to the electrowinning of light metals.

Jan 1, 1994

By Jyri Talja, Shaolong Chen, Hannu Mansikkaviita

"For optimum smelting results, proper treatment of the feed is needed to ensure favourable conditions for ignition characteristics, heat balance, mass balance with tolerable impurity levels, and overall process economics. Feed preparation consists of physical treatments before drying (blending), chemical treatments before drying, (roasting, if required), drying itself and physical treatments after drying (fractioning, if required).Effects of fluctuation on mineralogy and moisture should be minimized by blending the concentrates in a bedding plant prior to drying. As an alternative to drying, additional treatments such as roasting for impurity removal may be needed for part of the concentrate.Sustainability, energy efficiency, utilization of waste energy, low gas and dust emissions, product quality, availability and occupational exposure reduction are decisive criteria in drying today. These criteria are best met by the Kumera steam dryer, which has the best energy efficiency, zero CO2 emission, lowest operational and maintenance expenses, and superior availability and product quality.IntroductionFeed preparation plays a crucial role in having a smooth smelting operation and also the overall smelting economics in metal production. Therefore, it is of significant importance for all copper, nickel and lead smelter operations in which sulphide concentrates are fed to the primary smelting furnace. Generally speaking, the higher the metal content in the matte after primary smelting, the more important the feed preparation. This is of particular importance in the direct blister (DB) process for copper production and direct oxygen nickel (DON) for nickel production.Bedding is the first stage in feed preparation. This is very important for the sake of smoothing the mineralogical fluctuation in the feed for better smelting control. Its importance increases as the number of concentrates available for the feed mix decreases."

Jan 1, 2012

The entrainment of copper matte in the slag during the slag skimming stage of a Peirce-Smith converter was studied with a dam break model. Experiments were carried out with a range of fluid pairs where the lighter fluid was allowed to overflow a weir and the amount of entrained heavier fluid measured. The resulting entrainment is measured as the ratio of the heavy to light fluid withdrawn. The fluids include oil-water, water- glycerol and salt solutions-water pairs to cover a wide range of densities and viscosities. It was found that the Richardson number, Ri, correlates the entrainment well. For the case of the liquid-liquid interface initially at the same height as the weir, the entrainment was found to vary with Ri-1/3. The transient flow was simulated with a volume of fluid (VOF) code written in-house and used a stairstep approach to represent flow obstacles. The code was validated against the experimental results with good agreement for the variation of the heights of the two fluid with time. The simulation showed that the prevailing mechanism for entrainment is due to a pressure differential created across the liquid in the converter during pouring resulting in the heavier liquid being rotated upwards and over the weir.

Jan 1, 1999

By Paul Dewison

For nine years, from mid-1987 to mid-1996, the copper market enjoyed what appeared to be an endless boom in which prices were much higher relative to production costs than for most other base metals. After the boom ended abruptly mid-1997 with the Sumitomo affair, copper was burdened by an overhang of new projects that promised to swamp demand in what, with the Asian financial and economic crisis of 1997, had become a considerably worse consumption environment. Now, demand prospects do not look so bad. If, as we suspect, we will be dealing with a more rational market in the future, it becomes all the more important to forecast accurately the prospects for consumption. In this paper, we present a new methodology for copper demand forecasting. The methodology forms the backbone of the demand-side analysis for the multi-client study entitled "Long Tenn Outlook for Copper", co-authored by Metalica Ltd. and Bloomsbury Minerals Economics (BME). Key components of the methodology are as follows. (1) Relate demand to economic structure. (2) Focus on products rather than refined consumption. (3) Apply a consistent products/applications analysis to all countries and time series. (4) Incorporate scrap market dynamics within the analytical framework.

Jan 1, 1999

By Henrique Ventura Oliveira

Continuous casting is the most important process for solidification of steels. In this process, the fluid flow pattern in the tundish and in the mould have significant effect on the product quality. Problems associated to fluid flow in the tundish include surface turbulence, ?short-circuits?, formation of dead zones and vortexing. During grade changes, mixing in the tundish plays a significant role in determining the length of the intermixed slab. All these flow aspects can be studied by means of mathematical and physical models. In the last years, numerical simulation of fluid flow has become a very popular tool in the analysis of the performance of continuous casting tundishes. In setting-up these numerical simulations, special care should be taken in choosing the appropriate mesh distribution, the interpolation scheme, the adequate location of the inlet boundary and the turbulence model. In the present paper, turbulent fluid flow in different configurations of tundishes was simulated. Different turbulence models were used in the simulations. Residence time distribution (RTD) and mixing curves during grade changes were predicted and compared to results obtained in physical models. The performances of the different turbulence models were evaluated. For the tundishes that have been studied, the performances of the different turbulence models tested in the present work were similar. There is no evidence that any of the models provided sustained improvement when compared to the well-established standard k- model. All turbulence models tested presented limitations in simulating flows under low turbulent Reynolds numbers.

Jan 1, 2006

By David Ellis

The next generation of Reusable Launch Vehicle (RLV) will utilize regeneratively cooled combustion chamber liners in the engines. The current design calls for using a new Cu-8 at. % Cr-4 at. % Nb (Cu-8 Cr-4 Nb) alloy for the liners. Work is ongoing to characterize the thermophysical and mechanical properties of the alloy from - 253 to 800°C, the temperature range to which the alloy will be subjected during service. The alloy has been commercially produced in quantity for NASA. The powder size has been characterized and the microstructure examined. The powder was extruded into bar using a commercial extrusion press. In addition, samples have been hot isostatically pressed (HIPed) at NASA Glenn Research Center. Both processing methods produced fully consolidated material. Transmission electron microscopy (TEM) revealed highly faulted Cr2Nb and some elemental precipitates. Cryogenic tensile testing showed the extruded specimens had significantly higher strengths than NARloy-Z (Cu-3 wt % Ag-0.5 wt % Zr) even after being subjected to a simulated braze cycle. The Young&apos;s moduli (Cu-8 Cr-4 Nb) were lower than NARloy-Z. The lower moduli is highly beneficial for reducing thermally induced stresses in rocket engine combustion chamber liners and similar applications.

Jan 1, 1999

By Patrick Clark

As part of the Mine Waste Technology Program (MWTP), a large-scale column test using bacteria and a sulfide ore was conducted at McClelland Laboratories, Inc., in Sparks, Nevada. Four technology providers participated in this demonstration. A mining company in Nevada provided the sulfide ore, process effluent and make-up water. A process effluent column, a chemical oxidation column, and the four biological treatment columns were set side by side on a test pad outside the laboratory building. The process effluent and chemical oxidation columns were used for experimental control. The goal of this project was to evaluate the viability and feasibility of using these biodegradation technologies to reduce the cyanide to the regulatory level of 0.2 parts per million (ppm) within an acceptable timeframe and with low operational costs. The column testing began on December 3, 1998 and operated until May 17, 1999. One technology provider reached the regulatory level within the 158 days. The remaining three biotechnology columns were approaching the regulatory limit at completion of the demonstration. The MWTP is funded by the U.S. Environmental Protection Agency (EPA) and is jointly administered through an interagency agreement with the U.S. Department of Energy (DOE).

Jan 1, 1998

By A. Warczok

The oxidation and smelting of chalcopyrite, bomite, chalcozine and pyrite has been studied under simulated flash smelting conditions. The results of copper sulphide oxidation show that under constant oxidation conditions, the degree of oxidation drops sharply when the particle size is increased above a given range. This critical size range varies typically between 200 and 500 pm depending on the oxygen content in the gas phase. For bomite, chalcopyrite and pyrite, the critical size range increases with increasing iron content in the mineral and with increasing oxygen content in the gas phase. The extreme case is observed for pyrite in pure oxygen, where there is no effect of the particle size on the degree of oxidization. Microscopical observations of the oxidized products show the influence of different factors on the mechanism of oxidation and fragmentation of the sulphide particles. Based on microscopical analysis and phase identification of the oxidized products, a model has been proposed for the oxidation and smelting of copper sulphide particles in suspended state. The mathematical model describing the sulphide particle oxidation is supported by the obtained results. Using this model, it is possible to describe the role of particular factors in the sulphide minerals oxidation.

Jan 1, 1992

By N. El-Kaddah, V. L. Acoff, M. Arenas

"Control of the weld penetration, weld pool shape and temperature field in arc welding is critical to achieve the desired microstructure and mechanical properties in the resultant welds. This is particularly important in welding gamma titanium aluminides (y-TiAl) where the weld pool is relatively shallow and the temperature gradient in the heat-affected zone is quite steep. This paper investigates theoretically and experimentally the evolution of the shape of the weld pool for stationary gas tungsten arc welds in y-TiAl alloys. A mathematical model has been developed for predicting the electric current flow, the resultant electromagnetic forces in the metal, and the transient development of the temperature and velocity fields in the molten pool generated by a spatially variable heat flux at the arc-striking zone. The governing equations were solved numerically using the control volume technique. Welding experiments were carried out to determine the shape of the weld pool and the extent of the heat affected zone at different welding times for model validation. The numerical predictions were found to be in reasonable agreement with measurements. It is suggested that the model presented in this paper is likely to provide the information needed for predicting the microstructure and mechanical properties of y-TiAl welds. IntroductionIn recent years, there has been considerable interest in the welding of gamma titanium aluminides as a means of manufacturing high-temperature, high-performance components for turbine and automobile engines. These alloys are highly reactive, and must be welded in vacuum or inert gas atmosphere, rendering electron beam, and inert gas tungsten arc welding (GTA) to be the only suitable welding techniques for joining these materials [1-3]. The GTA welding is especially attractive because of its flexibility and relative cost-effectiveness. However, previous studies on the weldability and weld properties of these alloys using this process revealed a decrease in the mechanical properties in the fusion zone [4]. This is generally attributed to the change of the original duplex structure to a dendritic structure amplified by the shallowness of weld spot. Quantifying the effect of arc operating parameters on the geometry and temperature profile of the welding pool prior cooling is the first step for controlling the fusion zone microstructure and mechanical properties."

Jan 1, 1999

By Husamuddin Ahmadzai

A survey of regulations and state of the art control technologies is presented relating to the smelting of primary aluminium, copper and recycling of residues. Some costs associated with the alternatives and trends for the coming decade in this. sector are identified.

Jan 1, 1992

By Dieter Offenthaler

Catalysts used in petroleum industry often contain valuable amounts of PGMs. The typical recycling route for those materials is the pyrometallurgical one, but this treatment way offers limited flexibility with respect to small charge weights. A new process, combining a pyrometallurgical pre-treatment step of the ceramic carriers with a hydrometallurgical leaching procedure overcomes this disadvantage. It not only allows the economical treatment of even very small charge weights, but also gives the possibility to maximize the PGM yield by individually adapting the process to the different charge materials. Due to an ingenious process design, where all leaching agents and effluents are recycled in a closed loop and therefore no waste waters leave the process, process operation becomes very economical. However, the temperature-time-regime in the pyrometallurgical pre-treatment step is of major importance for the success of the whole process. Therefore various investigations have been done to identify how the different process variables in the pyrometallurgical pre-treatment influence the subsequent leaching procedure. It turned out, that the adjustment of the correct phase-modification in the ceramic carrier materials during the pyrometallurgical treatment is the key factor of this process step. Although it is a troublesome issue to exactly adjust the correct phase modifications, it is the prerequisite to take advantage of the benefits of this new process concept.

Jan 1, 2006

By Tracy Morris, Weldon Read, Luis Navarro

"Bismuth is a recognized contaminant in the electrolytic refining of copper that can render many cathodes to be outside ASTM standards and unsuitable for copper rod and other downstream products if not carefully controlled. This paper portrays the performance of Molecular Recognition Technology (MRT) for bismuth removal at the Amarillo Copper Refinery (ACR) and describes how the highly selectivity gel has been successfully used to achieve good bismuth removal and how many pit falls and draw backs have been overcome.IntroductionASARCO operates one of the largest copper refineries in the world at Amarillo, Texas. The main feed for this refinery is produced at the Hayden smelter in Arizona. During the operation of this smelter a variety of metals are carried as impurities in the copper anodes because of the diversity of concentrates and residue products used as raw materials in the smelter feed mix. Even though the impurities are concentrated enough to be detected at the smelter, it is difficult to remove them completely. A simple way to control impurities at the smelter is to minimize the addition of material with a high concentration of impurities to the charge in order to reduce the output of this metal species. All this leads us to have a ""refinery problem"" [1,2,3]."

Jan 1, 2012

By L. Z. Villanueva

An investigation and evaluation has been performed to determine the potential utilization of electron beam irradiation technology for sulfur oxides removal from reduced-S02-strength metallurgical gases from copper smelters. These off-gases, though too weak to be converted to usable, concentrated: sulfuric acid by conventional means, are characterized by SO2 content higher than 2,000 ppm and a complex chemical composition, including high oxygen content and its generation occurring in a cyclical, fluctuating pattern. This work was based on information supplied by principal smelter companies in Chile. A laboratory facility with flow rate of 20 Nm3/h and equipped with an electron accelerator of beam energy 8.00 keV, has been used for testing. Influence on SO2 removal efficiency of operational parameters such as gas temperature, water vapor content, ammonia feed ratio and irradiation dose was established. The main conclusion of this work, from experimental laboratory tests as well as engineering studies, is that the Electron Beam Process (EBDS) is a cost-effective, simple and appropriate chemical process means for emission abatement. EBDS can, on a site-specific basis, adequately augment SO2 removal to upgrade overall abatement as required and in an optimal manner.

Jan 1, 1999

By Hideki Yamamoto

A new technology to convert fluoride gas (C2H2F4 ; R-134a) contained in the exhaust gases from semiconductor manufacturing plants and refrigerators directly into a harmless substance have been established, thus, presenting a new concept for the disposal of fluoride gases such as CFCs that are associated with the global warming. Experimental results verify that chemical reactions with metal compounds can take place at substantially lower temperatures of 700- 800K as compared with combustion. treatment temperatures of 1200-1500K. The reaction product is mainly metal fluoride, which chemically is a harmless material. Furthermore, this process is compact, easily controlled, safe and has low running costs. This paper deals with a new chemical reaction method for the harmless disposal of gases effecting the global warming.

Jan 1, 2003

By G. Scavino

A 0.5 wt.% C, 22 wt.% Mn austenitic steel, recently proposed for fabricating automotive body structures by cold sheet forming, due to favorable overall strength and ductility, exhibits plastic localizations during uniaxial tensile tests, whereas no localization happens during biaxial Erichsen cupping tests. Full-thickness tensile and Erichsen specimens, cut from as-produced sheets, were polished and tested at different strain rates. During the tensile tests, the plastic localization phenomena consist first of macroscopic deformation bands traveling along the tensile axis, and then of series of stationary deformation bands, each adjacent to the preceding ones; both types of bands involve the full specimen width and yield macroscopically observable surface relief. No comparable surface relief was observed during the standard Erichsen tests. The stress state being known to influence plastic localization phenomena, reduced-width Erichsen tests were performed with 10 to 30 mm width polished specimens, in order to explore the transition from biaxial to uniaxial loading.

Jan 1, 2009

By Yuanbo Zhang, Helei Zhang, Heng Yu, Guanghui Li, Zhengwei Yu, Tao Jiang

"Composite agglomeration process (CAP) is an innovative method for preparing blast furnace burden. For CAP, the classified raw materials of pelletizing feeds and matrix feeds are mixed, charged and sintered. The characteristics of these two kinds of feeds obviously affect the permeability of per-ignition bed, as well as the sinter productivity and quality. In this study, the Ergun equation is proposed to predict the pressure drop of CAP bed using the particle size distribution. The calculation process indicates that the Dv and the Em are the two tuning parameters. The results show that there is a gap between the calculated values by Ergun equation and the measured results by pressure drop testing facility. Eliminated this error by modified the Ergun equation and then validated it through experimental studies using simulated CAP mix and test facility. Therefore, the modified Ergun equation can be used to predict the permeability of CAP bed.IntroductionThe sintering process is one of predominant agglomeration processes for preparing ironmaking burden from iron-bearing materials. Sinter accounts for 70-80% of the blast furnace burden in China and the continuous improvement of sinter quality provides a guarantee to anterograde production of blast furnace. Sinter productivity and quality are strongly related to the permeability of the bed during sintering, which is dependent on the structure of the bed before ignition in the early stage [l]. The size distribution, the shape of granules and the bed voidage are the primary affecting factors to pre-ignition permeability."

Jan 1, 2013