Search Documents

By A. F. Giamei, F. Landis, M. O. Duffy, R. J. Mador

"The directional solidification of complex advanced gas turbine airfoils must be carried out without the nucleation of undesirable grains and with minimal shrinkage. Such problems are typically eliminated by using a number of mold design and process iterations. A more efficient approach is envisioned where a solidification model is generated and utilized to accelerate process development. Towards this end, the directional solidification (DS) of simple geometrical shapes in a crystal grower apparatus has been simulated with MARC finite element nonlinear thermal analyses.The finite element models of cylindrical (2D) and rectangular (3D) cross-section bars in the DS environment are presented. Temperature dependent properties, the impact of latent heat of fusion and a time-dependent radiation boundary condition constitute the more salient features of the MARC models. Solidification zone thermal behavior is predicted during the withdrawal transient for the specific case of nickel based superalloys grown in ceramic shell molds. Comparisons of analytical results with experiments demonstrate notable prediction accuracy. INTRODUCTIONSingle crystal and uni-directional crystal turbine blades require tightly controlled conditions if metallurgically and mechanically acceptable parts are to be produced. Gated blade geometry and process parameters must be precisely determined if incorrect grain structure, orientation and shrinkage are to be avoided. Since purely experimental development programs designed to evaluate these parameters can be excessively costly and time-consuming, an effort combining engineering analysis and verification by experiment has been initiated at Pratt & Whitney. Comparison of analytical predictions and measured data for geometries simpler than a turbine blade, namely cylindrical and rectangular bars, comprised the initial stage of this effort. Subsequent tasks involve modeling geometries of increasing complexity and ultimately the simulation of the directional solidification of the turbine blade, shown schematically in Figure 1. This paper summarizes the results of the initial stage of the effort."

Jan 1, 1986

By Zhang Chuanfu, Li Shixiong

"In the electrolysis electrodeposition or electroplating of aqueous solution of copper, lead, zinc, nickel, manganese etc, with the increase in cathodic over potential the reducing rate of metal and the cathodic current efficiency increases and the deposit becomes more compact and smooth. According to this principle, a method and equipment of the auto-control of electrolyte quality is invented. The industrial application shows that this method turns the experienced operation into auto-control. The quality and quantity of metal is improved greatly and the consumption of electric energy is reduced.In the electrolysis, electrodeposition or electroplating of aqueous solution of copper, lead, zinc, nickel, manganese etc, usually organic additives are added according to the state of cathodic deposit according to experience. This traditional and experienced operation, often lead to that the quality of additive is not optimum which affects the quality and quantity of metal and increases the consumption of electric energy. To counter the controlling problem of the quantity of additive, the authors have invented a corresponding equipment of the auto-control of electrolyte quality [1], it has found application in industrial practice."

Jan 1, 2000

By George Owusu

A study has been carried out on the use of solvent extraction, instead of the traditional zinc dust cementation process, to remove copper from concentrated zinc sulphate leach solutions. In a series of experiments using plant solution containing 1.9 g/L Cu, 2 g/L Fe, 173 g/L Zn, 7.9 g/L H,SO,, 0.25 g/L Cd, 15 mg/L Co etc. and LIX 622 in SX-1, up to about 97-98 % of copper present in the zinc sulphate leach solution was extracted with negligible co-extractions of zinc, iron, cadmium, cobalt, etc. pH modification was not required for this reagent. The copper loaded organic was almost completely stripped using 150 g/L sulphuric acid. Investigations into the effect of any possible organiclextractant contamination on zinc electrowinning showed (if any) little effect on current efficiency if the organic contamination is less than 45 ppm; current efficiencies of 95-97 % were obtained. At organic contaminations higher than 45 ppm, the current efficiency dropped to about 92- 94 %. Visually, the organic-contaminated cathode sheets had rough surface morphology, becoming more intense with increasing organic concentration, compared to the non-contaminated cathode sheets.

Jan 1, 1998

By Andrzej Warczok

Intensive smelting of copper concentrate in Teniente Converter (CT) leads to the production of high grade matte and highly oxidized slag. Smelting slag is processed in Teniente vascular slag cleaning furnace. The slag composition and forms of copper affect the slag cleaning process and final copper content. Converting of high grade matte in Pierce-Smith converter faces some difficulties in proper slagging of iron oxides. Overblowing in copper making stage allows for slag liquidation but leads to high content of copper oxide in converter slag. Converter slag recycling into CT results in the increase of the participation of oxidic copper. Separate treatment of converter slag and its impact on the forms of copper in CT slag has been analyzed. Thermodynamic properties of a system and kinetic limitations pointed out the negative effect of converter slag recycling on the forms of copper and copper recovery in slag cleaning stage. Experimental results of slag cleaning tests in a crucible scale as well as microscopic examination of laboratory and industrial slag samples supported the above analysis and permitted to formulate recommendations of separate processing of converter slag. Keywords: copper, losses, slag, recycling

Jan 1, 2001

The standard procedure of fire refining consists of sulphur removal via air injected through tuyeres, arsenic slagging via soda-lime flux and oxygen reduction by air or oxygen deficient air or a steam fuel mixtures. The use of porous plugs to stir with an inert gas has been mainly considered as a surface renewing agent that increases the product quality and shorten the refining cycle. In the present study the effect of the bottom stirring by nitrogen gas injection through porous plugs for the treatment of the crude copper in the range of 400-150 ppm sulphur, 3,000-2,000 ppm arsenic and 14,000-7,000 ppm oxygen content was investigated. The combined effect stirring-reducing, by the use of air or a steam fuel mixtures through tuyeres for oxygen removal, follows a kinetics of first order where the constant, K, can be represented by the following polynomial expression: K = A * R2 + B * R + C Where A, Band C are constants that depend on the nitrogen flow rate and R is the air-fuel ratio or the steam-fuel used in the reducing step. Depending on the optimization of the flow of nitrogen and the air-fuel or steam-fuel mixture and only if just the oxidation, complexing and reducing steps are considered, the process cycle might be shortened by 45%.

Jan 1, 2003

By Gordon A. Irons

"Powder injection for melt refining is widely practiced in the steel industry, and is gaining acceptance in the non-ferrous industries. In these commercially-important systems, the thermodynamics and kinetics may be very complicated. More than one element may be removed by refining, and often the refining agents are not just one compound. In this paper, the thermodynamic and kinetic aspects of these processes are reviewed. A number of examples are given, such as the desulphurization of iron with a variety of reagent mixtures, and selenium removal from copper with several different reagent combinations.IntroductionI am very pleased and honored to present a paper at this Symposium recognizing the many contributions of Professor Howard Womer. Even at the time I was an undergraduate student, the WORCRA process was part of the curriculum. I remember at the time that I was fascinated by the concept, and due to it and the many other rapid developments in Process Metallurgy, I chose it as my field of study. I think the Symposium is testimony that Professor Womer has touched the lives of many others as well.My original assignment was an overview of the basic aspects of gas and solids injection. However, I reviewed most of this material at the Savard/Lee Symposium [1]. In the present paper, I will present some of the basic issues related to refining with powder injection, using work that we have recently completed in both ferrous and non-ferrous systems."

Jan 1, 1996

By Ana E. Bohé

Chlorination process is an attractive and efficient method for the metal recovery from complex materials. The process that is performed at high temperatures, allows converting all the metals contained in the material into their respective chlorides which are further separated in a selective way. Aluminum metal matrix composites with discontinuous ceramic reinforcement of short fibers, whiskers, and particles have been gaining wide acceptance as an important engineering material in automotive, aerospace, and electronic industries. Since the ceramic reinforcements are still quite expensive and contribute significantly to the final cost of composite materials, the feasibility of their recovery from the manufacturing scrap and further recycling is a factor of increasing economic interest. In the present work, a theoretical and experimental study is given for the recovery of Al2O3 and SiC particles and short fibers from three commercially available aluminum-matrix composites produced by molten metal mixing route. The process consists of transforming the constituents of metallic alloy matrices in gaseous chlorides that are dragged by the gaseous stream, while the ceramic reinforcement remains as a solid residue in the reaction bed.

Jan 1, 2006

By Mei Song, Qingyu Deng, Xuewei Lv, Lu Liu, Chenguang Bai, Meilong Hu

"The carbochlorination of several silica materials was carried out in the temperature range from 900 °C to 1200 °C. In this study, silica oxides and gaseous chlorine with carbon as reductant were used. The optimal carbon silica mole ratio in different temperature was calculated by Factsage software and the results showed that the optimal values are 1.2, 1.4, 1.6, 1.8 at 900 °C, 1000 °C, 1100 °C, 1200 °C, respectively. According to the experiments, the chlorination ratios of several silica materials were increased with temperature increasing. In the same temperature, the chlorination ratio of diatomite is the maximum and the chlorination ratio reaches 79%% when C/SiO2 reaches 3 at 1100 °C.1, IntroductionPolycrystalline silicon is the main material to manufacture the silicon polished section, solar battery[1] and high purity silicon wafers[2], also which is the most basic function material of semi-conductor industry, electronic information industry and solar photovoltaic battery industry[3]. The conventional manufacturing process of polycrystalline silicon would be divided into three parts: the improved Siemens method, which was introduced and became the main process to produce the polysilicon products in China. Silane method and fluidized bed method. Silicon tetrachloride and chlorosilans have been employed as by-products in several fields like electronic, telecounications and metallurgy[4-6]• At present, the main applications of silicon tetrachloride include production of trichlorosilane by catalytic hydrogenation, synthesis of fumed silica and ethyl orthosilicate, production of optical fiber grade silicon tetrachloride.The conventional routes for the silicon tetrachloride production have been reported, including the direct chlorination and the chlorination process of ferrosilicon, abandon catalyst and silica[7]."

Jan 1, 2013

By C. Acuna

The standard procedure of fire refining consists of sulphur removal via air injected through tuyeres, arsenic slagging via soda-lime flux and oxygen reduction by air or oxygen deficient air or a steam fuel mixtures. The use of porous plugs to stir with an inert gas has been mainly considered as a surface renewing agent that increases the product quality and shorten the refining cycle. In the present study the effect of the bottom stirring by nitrogen gas injection through porous plugs for the treatment of the crude copper in the range of 400-150 ppm sulphur, 3,000?2,000 ppm arsenic and 14,000-7,000 ppm oxygen content was investigated. The combined effect stirring-reducing, by the use of air or a steam fuel mixtures through tuyeres for oxygen removal, follows a kinetics of first order where the constant, K, can be represented by the following polynomial expression: K = A .* R2 + B * R + C Where A, Band C are constants that depend on the nitrogen flow rate and R is the air-fuel ratio or the steam-fuel used in the reducing step. Depending on the optimization of the flow of nitrogen and the air-fuel or steam-fuel mixture and only if just the oxidation, complexing and reducing steps are considered, the process cycle might be shortened by 45%.

Jan 1, 2003

By John A. Mavrogenes

Reflected light microscopy and electron microprobe techniques were used to determine the mineralogy, phase percentages, grain sizes, and textures of Co-Ni-rich mattes. The mattes were produced by submerged bath smelting at the University of Missouri-Rolla Pyrometallurgical Center of a flotation concentrate with 4.S% Co and 5.1% Ni that was prepared at the United States Bureau of Mines Rolla Research Center by flotation up-grading of the cobalt and nickel content of a copper concentrate from the Magmont mine, Viburnum Trend, Southeast Missouri. Nine distinct phases were distinguished in the matte samples, and three of these contain cobalt and nickel. The phases that were free from cobalt and nickel are bornite, chalcocite, pyrrhotite, magnetite, metallic copper, and galena. Submerged bath smelting serves to segregate the cobalt and nickel into phases that can subsequently be recovered by flotation. These phases are: shandite (Ni3PbZSZ)' cobaltpentlandite ((Co,Ni,Fe)9SS)' and Co-bearing Fe-rich sphalerite ((Zn,Fe,Co)S). Most of the cobalt occurs in cobaltpentlandite, but some is present in sphalerite. High total air conditions during smelting favor the development and segregation of cobalt into cobaltpentlandite. Nickel occurs in cobaltpentlandite and shandite. Shandite contains lead, a deleterious constituent in the smelting of cobalt and nickel.

Jan 1, 1989

By Jing Zhang, Qing Xiao, Xulong Liu, Qiuju Li

"Pickling sludge generated from stainless steel production process contains large quantity of Cr, Ni, and Fe. The disposal of and fill sludge directly not only leads to the heavy metal dissolves in the soil and underwater, but also loss value metals. However, the major mineral phases of value metal are hydroxides and there are lots of calcium fluoride and water in the sludge. So the pickling sludge has to be pretreated before reduction-magnetic separation. The TG analysis, reduction reaction and magnetic separation were all used to study the pickling sludge. The result indicated that up to 900°C the total weight loss of pickling sludge was 22.32%. The mass contents of Fe, Cr and Ni in the tailings (non-magnetic) were 4.27%, 0.067% and 0.041% respectively.IntroductionSince 21st century, the stainless steel production in the world has been continuously increasing because of its excellent performance [1]. However, high stainless steel production means a high pickling sludge production. For example, in a stainless steel plant with waste water quantity of 100m3 /h, the production of pickling sludge will exceed 15 Kt/a. Pickling is essential for generating of a homogeneous and corrosion-resistant surface during stainless steel production subsequent process. Pickling of stainless steels is predominantly carried out with an aggressive solution, sulfuric acid H2S04 or composed of nitric acid HN03 and hydrofluoric acid HF [2]. During the pickling process, the pickling acids are recovered through ion exchange and metal ions such as Fe3+, Cr3+ and Ni2+ get into the acids forming the pickling waste water [3]. Then, the pickling waste water is precipitated with lime, forming pickling hydroxide sludge. It is not feasible to recycle or treat the pickling sludge using conventional methods, because the sludge has high contents of calcium fluoride and water but low contents of iron, chromium and nickel. However, it would also pose a potential environmental problem if deposited outdoors over a long term because it contains heavy metals such as Cr and Ni. At present, solidification/stabilization (S/"

Jan 1, 2014

By Joseph C. Rota

The Carlin Trend is one of the most significant gold mining districts in North America. Located in northeastern Nevada, a total of over 17 million ounces of gold have been produced since 1965 at Newmont Gold Company's open-pit and underground operations. Oxidized portions of the sediment-hosted, disseminated gold deposits at Carlin generally consist of finely disseminated concentrations of sub-micron sized native gold particles hosted in Paleozoic siliciclastic or carbonate rock. Oxide ore is commonly amenable to dump leach or heap leach processing, yielding an average 50 to 70% recovery of total contained gold. Refractory unoxidized ore requires some form of pretreatment oxidation to ensure economic gold recovery. Geologic ore control is typically combined with standard assay and engineering techniques to maintain both grade and metallurgical control ofleach grade ores. Mine geologists provide a vital function through field observation and recording ofmineralogic data during daily, visual blasthole logging. Intricately mixed refractory materials must be separated from oxide ore to ensure highest possible gold recoveries. Geologic information is combined with assay data to create mine polygons in an engineering computer database. Mining selectivity is further enhanced by in-pit ore control geologists who are available to make production decisions based on direct mineralogic observations at active mine faces.

Jan 1, 1997

By Marco Antônio Siqueira Rodrigues

The possibilities for treating rinse waters fiom chromating bath by electrodialysis are discussed together with the possibilities of optimizing the treatment process for waste reduction and reuse of water and chemical products. An industrial effluent with 4600 ppm of Cr(VI), besides other metallic contamination, was used as work solution. This solution has been recirculated on an electrodialysis cell of three compartments, using exchange membranes Selemiom AMT and CMT. A migration of dichromate ions into the anodic compartment was obtained, so that an extraction of circa 99.9 % of Cr(VI) present on the solution was observed, resulting in water with a Cr(V[) concentration of 4 rnd. These results show that electrodialysis can be used to treat these effluents, and this water could be reused as rinse water. The solution of the anodic compartment, consisting at the beginning of the experiment of H2S04, 0.1 N, reached 7200 mg/l of Cr(VI). This concentrate could be reused on the chromating bath itself.

Jan 1, 1999

By A. M. Strachan

The application of submerged electric arc furnace smelting techniques to tin concentrates at the Capper Pass tin smelter in England is discussed. Some experimental data from earlier small scale 50 KVA electric smelting testwork on various low and medium grade tin concentrates is presented. Design considerations for the construction of a 3 MVA electric furnace to treat tin concentrates from the East Kemptville mine in Canada are considered, together with necessary precautions peculiar to the construction of a high grade smelter in close proximity to an existing low grade, complex non-ferrous metal smelting operation<. Slag composition modifications to optimise operational smelting conditions for various concentrates treated are discussed, together with refractory selection. The effect of concentrate impurity levels on the permissible degree of recycle to produce a satisfactory metal product is highlighted.

Jan 1, 1990

By Laszlo Kadar, J. D. Lavers

"In the continuous casting of aluminum killed steel, the tundish nozzle often experiences clogging problems. Water model studies have shown that the clogging problem is dependent on the flow pattern in the nozzle entry region. In particular, the flow can separate at the entrance to the nozzle, leading to the development of a recirculation region. Although a nozzle can be designed such that no recirculation develops, even a small misalignment from the vertical positioning of the nozzle may render the design ineffective.To reduce the possibility of nozzle clogging, the recirculation zone must be reduced or eliminated. This may be achieved by moving the fluid downwards or raising the turbulence level in the separation region. In the case of a tundish nozzle, it is proposed that this can be achieved by using electromagnetic forces.To generate the required electromagnetic force, two systems are considered. The first is based on injecting a DC current; the second by using electromagnetic induction. Both methods are described in this paper. Order of magnitude calculations are provided to illustrate that both methods are essentially feasible. The performance of each method in terms of modifying the turbulent flow characteristics in the nozzle entry region is then examined using a numerical model. It is shown that both methods can greatly reduce the recirculation zone. A cylindrical nozzle was chosen for the model studies since it represents a worst case situation.On the basis of the model studies, it can be concluded that whereas both of the proposed methods have the potential to reduce the troublesome recirculation zone, the induction method appears to be simpler in terms of practical implementation."

Jan 1, 1999

By Cristián Araya L.

A dynamic agglomeration, heap leaching, solvent extraction and electrowinning software, called NICO, has been developed in order to either design or simulate copper ore recovery plants. NICO contains a library of routines, each representing a unit operation or piece of equipment, which are assembled like a meccano to match almost any wet plant configuration. Routines include agglomeration or curing either in drums or belts, belt conveyors, heap stacking and reclaiming, heap leaching of oxide, sulfide or mixed copper ores, heap irrigation, drainage, ponds, mixer-settlers, filters, columns, coalescers, tanks, electrowinning cells, pumps, and all connections and related piping. All models are semi- phenomenological, i.e., they include all physical-chemical, mass, thermal, transport equations, which are required to represent as closely as possible the equipment or unit operation. However, operating experience has been incorporated into the model in order to make it simpler, faster and reliable. This experience has been tested in several plants in Chile since 1992. Site meteorological data is simulated also; in this way the model is responsive to weather conditions (temperature, solar radiation, ambient humidity, atmospheric pressure, wind velocity, etc). NICO has been used recently for design and optimization studies in copper plants in Chile like Radomiro Tomic, Collahuasi and Zaldivar. A user-friendly interface allows fast and comprehensive simulations. The entire plant is shown in a single graphic screen, so the user can see all the relevant information, and soft-keys are provided in order to change parameters on-line and watch their effect in final copper production in cathodes. Model also calculates and reports operating parameters, as well as estimated investments and operating costs.

Jan 1, 1999

By Richard D. Hagni

Process mineralogy has not been given adequate attention in years past, because geologists have not been sufficiently interested in applying mineralogical techniques to industrial processes, and most process engineers are not adequately trained to use them. Although some individuals and institutions have made efforts to improve the situation, it is only in the last few years that the significance of applying the methods of mineralogy to a wide variety of industrial processes has been fully appreciated. Presently, the formation and organization of several groups devoted to applied mineralogy have created a more amenable climate for the development of process mineralogy. As a result, the presentation, discussion, and publication of the results and case histories of process mineralogy have become fairly common. Short courses affording hands-on experience with applied techniques are now available to the many geologists and process engineers engaged in industrial mineralogical processes. The future role of the process mineralogist is viewed as an expanded one, which will increase in value.

Jan 1, 1982

By Massoud Hassanabadi

Filtration using Ceramic Foam Filters (CFFs) is a method widely used to separate inclusions from molten aluminium. In the present work, the specific permeability and form drag coefficients of nominal 50 mm thick commercial Al2O3- based CFFs, of grades 30, 50, 65 and 80, have been calculated from pressure drop experiments using high (60–500 mm s−1) and low (0.2–10 mm s−1) water velocities. Moreover, 2D axial symmetric Computational Fluid Dynamic (CFD) models have been developed, using COMSOL Multiphysics® to validate the experimental results. The empirically obtained values were defined as global parameters used to model the pressure, as well as the velocity fields in the water pipes and in the CFFs. The modelled pressure drop over the filter thickness for the high water velocity experiments showed < ± 1% deviation from the corresponding experimental results for all CFF grades. Moreover, the developed model also showed good agreement with the experimental results obtained from the low water velocity experiments, where the deviation of the pressure drop for the CFF samples of grade 30, 50 and 65 were ≤ ± 4.6% and for CFF samples of grade 80 ≤ ± 13.4%.

By J. H. Puffer

The copper mineralization of the Mesozoic Passaic Formation of New Jersey is typical of copper deposits in eastern North American Mesozoic sediments. Most such deposits are located at the base of the first of several basalt flows that are interbedded with continental, red-bed sediments. The copper mineralization is similar in most respects to that of the Keweenawan Basalts of the Lake Superior area. The first basaltic flow units of the eastern North American Mesozoic basins, and the Keweenawan Basalts, are continental quartz tholeiites of similar chemical composition and copper contents. The copper minerals and associated zeolite facies metamorphic mineral assemblages of these two rock units are also approximately the same. Stoiber and Davidson (1959) suggested that Keweenawan copper was mobilized and concentrated during metamorphism. The evidence pertaining to the Mesozoic copper deposits of New Jersey is consistent with such an interpretation and also with DeVore&apos;s (1955) suggestion that ore fluids commonly arise as a result of the mobility of metals under metamorphic conditions. There is additional evidence that final metamorphic concentration of Mesozoic copper was preceded by an initial stage of hydrothermal precipitation related to fluids emitted by basaltic magma.

Jan 1, 1987

By Xiaodi Huang, Matthew Andriese, Zheng Zhang, Jiann-Yang Hwang, Zhiwei Peng

"A simplified finite-difference time-domain (FDTD) algorithm for modeling microwave propagation in magnetic dielectric materials was developed and employed to study the microwave dissipation in magnetite. Heat transfer during microwave heating of magnetite was subsequently investigated by solving heat transfer differential equation using explicit finite-difference (EFD) method. It is observed that temperature of magnetite surface increases rapidly in the first minute due to the rapid strength decays in both electric and magnetic fields within a short distance along the path of microwave dissipation. A temperature peak, initially formed at the surface of the sample slab, migrates inward as heating time extends and microwave power increases.IntroductionAs one of primary materials in iron and steel industry, magnetite exhibits excellent microwave absorption capability, which leads to great energy conservation in microwave assisted steelmaking [1,2]. The fast temperature increase in microwave heating of magnetite can be attributed to both dielectric and magnetic losses [2]. Although much experimental work has confirmed this observation, detailed computational studies for modeling of microwave field dissipation in magnetite at commonly used frequencies, such as 915 MHz, has not been well addressed [1,3].Finite-difference time-domain (FDTD) method is widely used in computational electrodynamics modeling to simulate the dynamics of electromagnetic wave scattering from various media [4,5]. This approach requires modeling algorithm to be formulated with integration of specific characteristics of each medium. An extensive literature survey indicates that current formulations are only suitable for modeling electromagnetic waves propagating in normal dielectric lossy materials [5,6]. Since magnetite is a magnetic dielectric material in which both dielectric and magnetic properties contribute to the heating process under microwave irradiation, a specific algorithm should be developed for the simulation."

Jan 1, 2012