Search Documents

By Oscar Perales Perez, Atsuo Kasuya, Kazuyuki Tohji, Yoshiaki Umetsu

"The removal of iron and various heavy-metal ions by their incorporation into stable ferrite-type precipitates at 25°C is a promising alternative to clean up large volumes of polluted aqueous effluents. Our research work investigated the conditions to produce magnetite and various M-bearing ferrites (where M: Zn, Cu, Co, Ni, Cd, etc.) directly from aqueous solutions at 25°C by simultaneous control of the oxidizing conditions and pH. The formation of the solids was followed by monit9ring the oxidation-reduction potential (ORP) and rate of proton release during the aerial oxidation of the suspensions at constant pH (contact stage). Only mildly oxidizing conditions, represented by ORP values between -110 mV and -150 mV and a moderate oxidation rate of Fe(II) species were conducive to well-crystallized ferrites at ambient temperature.' It was also found that increasing the Fe/M mole ratio in starting· solutions enhanced the stability ·of the M-bearing ferrites at ambient temperature. When the formation of the ferrite was incomplete, aging of the sludges in their mother liquors at 25°C promoted the crystallinity of the precipitates. The mentioned conditions ·favored the suitable progress of the ferrite-forming reaction involving the oxidation of Fe(II) entities, subsequent hydrolysis of produced Fe(III) species and dehydration of the intermediate:· Furthermore,· the ferrite formation at· low temperature permits the elimination of iron and co-existing heavy metal ions to sufficiently low concentration.In tum, the characterization of the precipitates evidenced their magnetic nature (room-temperature saturation magnetization above 60 emu/g) as well as the effective incorporation of target metal ions into the ferrite structure."

Jan 1, 2000

By Hongxu Li, Pu Liu, Hao Bai, Daqiang Cang, Lihua Zhao

"Coal, as the main energy in ferrous metallurgy, is consumed on a large scale and great amount of CO2 is emitted likewise. In this paper, a model, based on carbon balance, was developed for CO2 emission analysis, with data obtained from a typical integrated steelworks in China. The result shows that, CO2 emissions increase almost constantly with the growth of steel production. However, coals of different classes and product variety in the steelworks exerted an influence on CO2 emissions. Furthermore, three scenarios, including natural gas instead of coal for power generation, EAF process partly replacing integrated steelmaking, and feasible techniques applied to achieve lowest process energy consumption (FLPEC), were assumed to seek possible ways of carbon emission reduction. The result proves that the second scenario is most effective. If 40% of the steel product could be from EAF process, CO2 emissions would be reduced by 45.07%.IntroductionGlobal warming has become a global environmental problem, which is generally caused by excessive emission of greenhouse gases, such as CO2, generated from human activities and industrial processes. It is estimated that about 7% of global CO2 emissions was from iron and steel industry. Further, if the ore and coal’s mining and transportation are included, the CO2 emissions would reach 10%[1]. In general, the relationship between energy saving and CO2 emission reduction is positive correlation. However, in iron and steel enterprises, due to different types of energy resources like coal, heavy oil, natural gas, the consumption of which will generate different amount of CO2, are used, different energy consumption structure in iron and steel enterprises will lead to difference of CO2 emissions.In order to assess the CO2 emission reduction potential of China’s steel industry, Ke Wang etc.[2] developed a model using LEAP software to generate 3 different CO2 emission scenarios for the industry from 2000 to 2030. LEAP is a scenario-based software tool for integrated energy-environment and greenhouse gas mitigation analysis. The amount of CO2 emissions was obtained by the following equation:"

Jan 1, 2011

By Motohiro Horiguchi, Kazuo Ichii, Toshio Oishi

"As a fundamental study to prepare copper-based alloys with rare earths (RE: La, Gd, Nd, Ce and Y) without any inclusions, the solubility of rare earth in liquid copper was experimentally determined. Liquid copper alloys were equilibrated with carbon and rare earth carbide in a graphite crucible in an argon atmosphere at 1523-1873 K.Solubilities of rare earth in liquid copper were determined by approaching the equilibrium values from both the lower and the ·higher concentrations than those expected· in the preliminary experiments. They were expressed as a function of temperature. Carbon in Cu-RE alloy was also analyzed and thermodynamically discussed.IntroductionOver the past several years, the demand for highly conductive and high strength copper-based alloys, such as Cu-Cr, Cu-Zr and Cu-Cr-Zr for use in electronic materials has increased.1 -7 These alloying elements are very reactive and easily oxidized to form oxide inclusions during melting. To avoid the oxide inclusions, it may be effective to utilize the strong reducing power of carbon in conditions under which no carbides form.In this study, to provide fundamental data for producing Cu-RE( rare earth) alloys without any inclusions, the solubility of rare earth in liquid copper in equilibrium with .carbon .was determined and discussed on the basis of the experimental results and the thermodynamic data.ExperimentalSample preparation for equilibrium experimentsOxygen-free copper (99.99%), lanthanum (99.9%), gadolinium (99.9%), neodymium (99.9%), cerium (99.9%) and yttrium (99.9%), and their oxides were used as starting materials.Each rare earth carbide was prepared by mixing rare earth oxide with carbon, which is a little more than the stoichiometric composition, pressing it into a tablet form and sintering at about 2000.K for 20 ks in a vacuum furnace using a graphite crucible. Powder X-ray analysis showed that only the carbon and rare earth carbide (REC2) was present in each sample.Cu-RE mother alloys (5-20 mass % RE) were prepared beforehand by mixing metallic rare earth with oxygen-free copper, and melting in an electric arc furnace."

Jan 1, 2000

By Anna Franzkowiak, Dean Gregurek, Alfred Spanring, Angelika Ressler

In order to determine the most suitable refractory products and improve the lining lifetime for the diverse furnaces used in the nonferrous metal industry, corrosion tests are performed at RHI’s Technology Center. The practical facilities include the cup test, induction furnace, rotary kiln, and drip slag test described in this paper, which enable a comprehensive understanding of the chemo-thermal brick wear on a pilot scale. The corrosion trials are performed with actual slags generated during operations at a customer’s plant. To determine the highest influencing wear parameter, every single test is combined with a detailed mineralogical investigation and thermochemical calculations performed using FactSage. Based on the results, tailored refractory solutions for the nonferrous metal industry can be provided in combination with trials conducted at the customer’s site.

Jan 1, 2014

By Ramiro Escudero G.

Since the introduction of column flotation almost forty years ago the column technology has grown into several non-mineral applications such as among others the effluent treatment, soils recovery and de-inking of recycled paper. Recent studies have demonstrated that particular characteristics of the dispersion (bubble size, gas holdup, bubble surface area flux) are needed for a given flotation column duty. In this work, two kind of spargers were tested (i.e., internal and external) using a 4 inch column lab in a two phase system. Results show that the external sparger provides a dispersion with characteristics that include those produced by the two internal spargers.

Jan 1, 2003

By Mikiya Tanaka, Mikio Kobayashi, Mansour A. S. A1Ghamdi, Kenji Tatsumi, Yukinori Saiki, Hirotaka Senba

"In order to recover nickel ion in a spent electroless nickel - phosphorus alloy plating bath and, at the same time, to remove impurities such as iron and zinc, the applicability of solvent extraction with LlX84I as the extractant has been investigated using actual spent solution. Although the extraction efficiency of nickel from the spent solution is considerably lower than that from the nickel sulfate-nitrate solution, nickel in the spent solution is selectively extracted with high efficiency at the pH of 6 - 7. The extracted nickel is effectively stripped by sulfuric acid at a pH of less .than· 3. On the basis of these results, a· flowsheet for recovering nickel from the spent solution is proposed Chemical equilibrium calculations of the spent solution has shown that the complex formations of nickel with anions such as lactate and phosphonate ions become predominant in the pH range between 2 and 6. This results in the depression of nickel extraction efficiency from the spent solution as compared with that from the .nickel sulfate-nitrate solution. By combining these aqueous equilibrium calculations with the· extraction model considering the extraction stoichiometry and the aggregation of the extractant in the organic phase, the extraction behavior of nickel is quantitatively predicted.IntroductionElectroless plating is indispensable for the recent advanced industries such as the electronic and mechanical industries. Electroless plating baths are repeatedly used by supplying the metal salts; however, the accumulation of the counter anions of the metal ions, the components formed by the oxidation of the reducing reagents in the plating baths, and the metal ions as impurities dissolved from the surface of the objective materials degrades the· quality of the plating. Thus, the baths are finally treated by a precipitation method to form a large amount of metal sludge, which is disposed in dumping sites. Therefore, from the standpoints of environmental protection and resource preservation, it is highly desired to establish a recycling process of the plating baths with minimum emission. Solvent extraction seems to be one of the 'suitable methods to recover metals from the spent electroless plating baths, because the concentration of the metal ion in the baths is relatively high, which is advantageous to solvent extraction as compared with the ion-exchange and adsorption methods. Some studies about the application of solvent extraction have already been carried out using simulated spe11t electroless plating baths [1-3]."

Jan 1, 2000

By Ross R. Bhappu

A theoretical and experimental investigation into pyrometallurgical refining of chloride leach/electrowin copper is described. The two techniques investigated were (i) vaporization and (ii) gaseous halogenation. Experiments were carried out with a packed bed of electrowon copper crystals and a boat of melted copper crystals. Nitrogen gas and Freon 12/nitrogen mixtures were used as the carrier and reac.tive gases. Vaporization was found to be effective in removing Bi, Pb and S while halogenation was effective. in removing As, Bi, Pb, S and Sb. Silver resisted all attempts at removal. Iron was removed but less effectively than the other impurities.

Jan 1, 1985

By Rui-Qing Li, John G. Peacey, Peter J. Hancock

"Noranda has been investigating a pyrometallurgical process for the direct recovery of zinc from zinc concentrate and zinc and iron containing residues. The process consists of injecting dry zinc concentrate and secondary zinc materials into a molten iron oxysulphide bath, volatilizing metallic zinc into furnace off gas essentially free of sulphur or S02, fixing sulphur contained in the feed materials as iron oxysulphide matte which is disposed, and recovering metallic zinc in an ISP type lead splash condenser. Combustion of petroleum coke with air or oxygen enriched air inside the oxygen containing matte supplies part of the heat, and the products of combustion dilute the zinc-laden gas to a desired level.This paper describes the process concept, thermodynamic background, experimental tests, mass and heat balance calculation for a conceptual flowsheet, environmental stability of the residue and advantages and disadvantages of the process. Experimental tests have successfully proved the process concept and thermodynamic predictions. Direct smelting of zinc concentrate and residues inside an iron oxysulfide bath has a great potential to become a cost effective and flexible zinc smelting process.1. INTRODUCTIONZinc is mainly produced by a roast-leach-electrowinning process route, which accounts for about 80% of the world primary zinc production. This process produces high quality zinc with very high zinc recovery (>95%) but suffers from several major drawbacks such as using high cost electricity as reductant, producing environmentally problematic iron containing leach residue (jarosite or goethite) and the difficulty in treating secondary zinc feed materials containing high impurity levels, such as electric arc furnace dusts from the steel industry, and other complex sources. Also in some areas, markets for sulphuric acid are distant resulting in negative realizations on acid sales.The Imperial Smelting Furnace (ISF) process is the major pyrometallurgical process to treat zinc-lead concentrate. The advantage of this process over the electrolytic zinc process is its flexibility in treating high-lead, bulk concentrates with high recoveries of lead, copper and precious metals. However, this is a two-stage process involving sintering of Zn-Pb concentrates followed by blast furnace reduction. The process requires large amounts of high-quality coke which is a major operation cost, and the sintering process which results in serious environmental problems."

Jan 1, 1996

By Hiroshi Hashimoto

For the application of sodium carbonate slag treatment to product high purity copper on an industrial scale, the counter-flow batch process that reduces the amount of utilized slag is proposed from the viewpoint of the post-treatment of slag. Based on the distribution ratios of several impurities between the slag and molten copper determined previously, the effectiveness of this process is discussed using a mathematical model and confirmed experimentally. According to the model, the slag consumption to remove Sb to a required level in case of the counter-flow batch process with 3 reactors is calculated to be around 30 % of that in the case of an ordinary batch process, where pure sodium carbonate is used as a slag at every stage.

Jan 1, 2003

By Jiangwei Shen, Cong Wang, Haibin Zuo

The research on the formation of Silico-Ferrite of Calcium and Aluminium (SFCA) in the process of cooling and solidification is rarely reported. The crystallization process was observed by using scanning electron microscopy (SEM) and optical microscope in this paper. The effect of different cooling system on the microstructure and phase composition of the sinters was investigated to obtain the appropriate cooling rate to improve the metallurgical properties of sinters. The experimental results show that the crystallization of calcium ferrite is getting better when the cooling rate is decreased from water quenching to cooling in the air. There are a large number of hematite phases with interconnected crystal structure in the sample cooled in the air. In the case of the compressive strength, it was determined by the mineral composition and pore structure, higher SFCA and hematite contents in sinter cooling in the air lead to a higher strength. Glass phase in the water quenching sinter was the major reason for the lowest strength. High porosity contributes to a decrease in compressive strength for the sinter cooling in the furnace. Therefore the air cooling was the appropriate cooling rate to achieve high quality sinter under this experimental condition.

Jan 1, 2016

By Shunsuke Yagi

A surface alloying technique was investigated using alternating pulsed electrolysis in an aqueous solution containing a single metal component for the formation of an Fe-Cr layer on an iron substrate. In the process, the iron substrate was dissolved during each anodic polarization of the pulsed electrolysis, providing iron ions in the vicinity of the substrate, while the Fe-Cr alloy was electrodeposited during subsequent cathodic polarizations. A bright, flat, and crack-free Fe-Cr layer with a composition gradient was obtained using a solution containing a trivalent chromium component and a complex forming agent together with some supporting or buffering salts.

Jan 1, 2006

By J. A. Gonzalez-Dominguez

During the electrorefining of lead by the Betts process, ionic concentration gradients become established within the slimes layer. These gradients contribute to precipitation of secondary products and to gradients in electrode potential applied to slimes filaments, and thereby affect the dissolution of noble impurities. This paper describes the experimental results obtained when a typical lead anode was dissolved under galvanostatic conditions with concurrent interruption of current at preset slimes thicknesses. Reference electrodes were incorporated within the lead anode to follow the potential gradients across the slimes electrolyte. Samples of the slimes electrolyte were withdrawn in-situ and their compositional changes were related to transport processes across the slimes layer. Upon current interruption the anodic overpotential decays, first abruptly (as the uncompensated ohmic drop disappears), and then slowly (due to the presence of a back E.M.F. created by ionic concentration gradients that decay slowly). Current interruption measurements showed that: (A) concentration gradients exist across the slimes layer, (B) inner solution potentials within the slimes layer can be larger than those measured from reference electrodes located in the bulk electrolyte, (C) secondary products can shift the inner solution potential to negative values that reverse upon re-dissolution and (D) ionic diffusion is seen upon current interruption but it is complex and difficult to model due to the presence of processes that can support the passage of internal currents. SEM and X-ray diffraction analysis of the slimes filaments indicated that secondary reactions leading to the formation of Si02 and PbF2 take place (mainly at the anodelslimes interface). The onset of these reactions and their relationship to the Pb-F-Si-H20 Eh-pH diagram are linked to the industrial operation of the Betts process.

Jan 1, 1994

By K. Morsi, P. Mehra

"Spark plasma sintering has gained a considerable amount of attention over the past decade, due to its rapid sintering rates, and low temperature requirements, but has so far been usually limited to the production of simple geometries. The present paper examines the current-activated production of extended geometries through the process of spark plasma ""extrusion"". Of interest in the present study is exploratory research into the effect of electrical current activation on the reactive consolidation of powder systems to form intermetallic materials.IntroductionSpark Plasma Sintering (SPS) has been the subject of intense research over the past decade [ 1,2, 3,4,5,6]. The process boasts unique advantages which include ultra fast heating rates, shorter sintering times and lower sintering temperatures than needed in conventional sintering. The process is however limited to the generation of predominantly simple geometries. Recently one of the authors investigated the spark plasma extrusion of aluminum, where an aluminum powder compact is directly (Joule) heated through an applied DC electric current. Here extended geometries can be generated under the influence of electric current. A number of heating sources were identified including the heat source from current, i.e. Joule heating, frictional heating and heat from the deformation energy. However in the case of reactive powder systems, an extra ""one-time"" transient heating source can be supplied. By considering combustion synthesis of powders, this heating source is derived from the reaction between elemental powders to exothermically form a product at some ignition temperature [7]. This exothermic energy heats the compact to the maximum ""combustion temperature'', which could be hundreds of degrees higher than the ignition temperature. Hence a high temperature processing window (of short duration due to heat losses to the surroundings) becomes available in which the material is most suitable for stress-induced deformation and consolidation. For reactive spark plasma extrusion, two scenarios can be envisioned. The first is where the reactive powder compact is ignited through the application of current, and extruded within the high temperature processing window (also under the influence of current). The second scenario is to allow the heat of deformation/friction to heat the material during extrusion, to simultaneously force a reaction and consolidation. Here it is expected that the processing window will be very small if feasible."

Jan 1, 2011

By S. Shrivastava

A structure based model has been developed for the prediction of viscosities of K20-B20, melts. These melts exhibit an anomalous behavior of viscosity with continuous variation in B203 content. A maximum and a minimum are observed at low temperatures, which disappear on raising the temperature above the softening range. The addition of K20 to the borate melts causes two opposing phenomena: (1) depolymerization effects and the related breakdown of network structure resulting in the formation of singly bonded oxygens, which weakens the structure and hence causes a decreases in viscosity, and (2) the formation of four coordinated borons (BO4 tetrahedra) which strengthen the structure leading to an increase in the viscosity. The structural changes taking place in these melts on varying the temperature and the alkali content have been reviewed and are incorporated in developing this model. The predicted values are in excellent agreement with the experimental values over the whole temperature and composition range.

Jan 1, 1992

By C. J. Newman

The new Kennecott Utah Copper smelter, started in 1995, was designed to be the cleanest smelter environmentally in the world. The plant is operating at production rates above the original design capacity. Copper concentrate is smelted in an Outokumpu flash smelting furnace. Matte is granulated and processed using Kennecott-Outokumpu flash converting. Copper anodes are processed in a modernized copper refinery using the Kidd Process while anode slimes are processed for precious metals recovery using a unique hydro-metallurgical process. To allow the production of high quality cathode, using modem smelting and converting technology to minimize emissions, impurity control had to be carefully addressed. All process bleed streams from the smelter and refinery are treated in a hydro-metallurgical plant to fix impurities in a stable form, allow for the rejection of impurities as required and recover valuable metals. Special technology was developed for the copper refinery to ensure production of high quality cathode from anodes containing high levels of impurities. The smelter routinely achieves a sulfur capture in excess of 99.9% which is equal to less than 2 kg of SO2 per tonne of copper produced. This paper describes the design of the smelter and refinery and includes recent production and emission data and modifications carried out to allow operation at above the original design rates. It emphasizes the unique features required to achieve environmental and quality goals and compares environmental performance data to that published on other smelting operations. The processing of intermediate streams, the management of recycled materials and the impurity control strategy will be covered in detail.

Jan 1, 1999

By Hiroshi Hashimoto

For the application of sodium carbonate slag treatment to product high purity copper on an industrial scale, the counter-flow batch process that reduces the amount of utilized slag is proposed from the viewpoint of the post-treatment of slag. Based on the distribution ratios of several impurities between the slag and molten copper determined previously, the effectiveness of this process is discussed using a mathematical model and confirmed experimentally. According to the model, the slag consumption to remove Sb to a required level in case of the counter-flow batch process with 3 reactors is calculated to be around 30 % of that in the case of an ordinary batch process, where pure sodium carbonate is used as a slag at every stage.

Jan 1, 2003

By F. Shahbazian

attempt to systematize the knowledge on slag viscosities, the present work was carried out. The Among the physical properties of slags, viscosity is very important in understanding the mass out in the temperature range 1438-1762 Q The rotating cylinder method was used in the viscosity measurements. Crucibles and spindles made out of pure iron were employed. The transfer phenomena in metallurgical processes. The viscosities of fayalitic slags are of great interest in the non-ferrous metal industry, with special reference to copper production. In an slags were prefused before the measurements. In order to take into account the vaporization reactions involving CaF2, pre- and post measurement samples of the slags were chemically analysed and the compositions were ascertained. The results show that in the case of the CaO-SiO2 system, CaF2 additions tend to decrease the viscosity, in accordance with the expectations. In the case of the "FeO"-SiO2 system, at higher "FeO" / SiO2 ratios in the slags, a reverse trend was observed. The results are discussed on the basis of a viscosity model for silicate melts developed in the present laboratory as well as the structural considerations of silicates.

Jan 1, 2000

By N. E. Ablesimov

Electron probe X-ray microanalyser of a coating deposited with "Elitron¬22A" electrospark alloying (ESA) set (anode - Cr, base-catode - chrome vanadium steel) has shown that the zone of phase forming can be divided into three parts: the coating itself, diffusion zone and a thermal affection zone in the base material. Waves of iron and chrome concentrations have been found in the diffusion zone. The authors interprete them as a phenomenon of substance self-organizing in the 30 pill deep diffusion zone, characterized by a change of compositions during the transfer of material from the coating to the base: coating - 20 µm (FeCr2), diffusion zone - 30 µm (Fe3Cr, FeCr, Fe4Cr, Fe2Cr), base - steel (Fe - 87 %, Cr - 12 %, V - I %). This ESA phenomen has been noted for the first time. It may be relative to the phenomenon of periodic formation of secondary products during the mutual diffusion of reacting substances in the case of a one-way reaction. Similar regular structures may appear in the diffusion zone during ESA of vanadium steels with vanadium, manganese steels with manganese and so on.

Jan 1, 1999

By A. V. Tarasov, V. M. Paretsky

"The knowledge of the true phase composition of the liquid slag is a very important problem, mastering of which grants the possibilities for the scientifically founded choosing of the decoppering method of the autogenous smelting slags. The investigation using different methods of the phase composition of the flash quenched autogenous copper melt's slags has shown, that the most effective method of the slags' decoppering during smelting with the white matte production is the flotation of the recrystallized slags. In this work the authors posed the problem to realize the slags quenching with the rates similar to those, which are used in the modem investigations devoted to the flash quenching of the ironcontaining alloys, with the subsequent study of the quenched samples using the Mossbauer spectroscopy methods in order to establish the connection between the liquid slag's structure and the metals losses with the slag."

Jan 1, 2000

By M. K. Mohan

Lead recovery from process solutions contributes not only to the conservation of resources but also clean environment. Zeolites are natural aluminosilicates, which finds applications as catalysts and in wastewater treatment. In the present investigation, studies were taken up on the processing of Pb from process solutions by zeolites. Effects of pH of the solution, time and type of zeolite viz. chabazite, mordenite, erionite and clinoptilolite on the removal of Pb from solutions was investigated. Rate of sorption was found to depend on the pH of the solution and about 99 pct. recovery was observed at pH 6. Optimal conditions were established for the maximum recovery of lead from process solutions. Possible sorption mechanisms were proposed. The calculated adsorption constants calculated from Langmuir and Freundlich equations showed that the adsorption of lead on chabazite was strong.

Jan 1, 1999