Search Documents

By N. Menad

Thermal treatments of five different types of non-ferrous metallurgical wastes, under controlled atmosphere, were carried out at temperatures lower than 800 °C. The aim of these treatments was to reduce the toxic elements content and to increase that of valuable metals in the residue. <Best results were obtained by their treatments in air or hydrogen or successively both of them. Simple treatments using air or hydrogen of three samples allowed the elimination of more than? 95 % of their toxic elements and&apos; almost doubled their valuable metals&apos; concentration. For the rest two samples, combined treatment was necessary for their efficient decontamination and the concentration of valuable metals, in the treatments residue, to a reasonable value. Most of the solids issued from these treatments can be recycled in .the current non-ferrous metallurgical processes.

Jan 1, 1995

By D. Neuschiltz, M. Witthaut, R. Cremer

"Metastable (Ti,Al)N coatings with fee structure have been shown to exhibit superior performance as compared to TiN under conditions of wear at elevated temperatures due to their better oxidation resistance and hardness. The oxidation resistance of these coatings increases significantly with increasing Al-content. However, the deposition of (Ti,Al)N films with Ti/ Al ratios below about 30/70 leads to a hexagonal structure which is not suitable for tribological coatings. Only little is known about the location of the cubic to hexagonal phase transition and hence about the optimum composition of (Ti,Al)N hard coatings.To determine the position of this transition, Tii-xAlxN films with different Ti/Al ratios were deposited on high speed steel at substrate temperatures between 100 and 700 °C by means of reactive MSIP. The composition of the films was determined by electron probe microanalysis (EPMA) and X-ray photoelectron spectroscopy (XPS), the crystallographic structure by thin film X-ray diffraction (XRD).It could be shown that in case of deposition temperatures of 300-700 °C a two-phase region exists in the metastable TiN-AlN phase diagram, which expands with increasing temperature, wheras at 100 °C substrate temperature no two-phase region was observed. But in opposition to the phase diagram known from literature, which is based on thermodynamic estimations, the detected two-phase region is narrow for typical PVD temperatures, thus allowing the deposition of cubic single-phase Al-rich (Ti,Al)N hardcoatings for tribological applications. Based on these results, a new Ti1-xAlxN film with x = 0.62 has been developed, which showed an increase of oxidation resistance by a factor of 4."

Jan 1, 1998

By Jun Li, Lin Chen, Tian-zu Yang, Wei-feng Liu, Wan-da Bin

"The Chinese bismuth production accounts for more than 80% all over the world in 2011. The main raw materials of bismuth smelting are bismuth concentrate and by-products of Cu or Pb smelting process. Many traditional methods of bismuth smelting in china was reviewed in this paper, such as reverberating furnace smelting, blast furnace smelting, fire-refining, ferric chloride leaching-hydrolysis, slurry electrolysis, and so on. But all the traditional pyrometallurgy or hydrometallurgy process have such shortages of low recovery, poor environment, and high cost. Therefore new technologies are introduced into the smelting process of bismuth concentrate, such as low-temperature alkaline smelting and side-blown bath smelting with oxygen-enrichment. These technologies have got great progress on energy saving, emission reduction, and friendly environment. Finally the development direction of new technology on bismuth smelting was prospected.IntroductionAs a green metal, bismuth has a wider applications, just extending from the traditional medicine, metallurgical-chemical engineering, low-melting alloys, solders, catalyst, and electronics to cosmetics, flame retardant, storage battery, semiconductor, supper conductor and nuclear energy etc[1,2,3,4,5,6,7]. This will increase the production of bismuth and promote the development and progress of bismuth smelting technology. At present, The major bismuth-product countries are China, Mexico, Peru, KZ, Bolivia and Canada etc, and China are dominating. A survey from the USGS[8] showed that Chinese bismuth production were 12,500 tonnes and got 80% of the world's in 2011. Thus the technology of Chinese bismuth smelting have a great representativeness."

Jan 1, 2013

By Akira Yazawa

The similarities and differences in copper, nickel and lead smelting processes are discussed based on the sulfur-oxygen chemical potential diagrams and the free energy minimization assessments using a thermodynamic software. The prominent features of copper smelting are ascribable to the fact that copper has a strong affinity for sulfur but weak for oxygen and the liquid phase immiscibility between Cu and Cu2S. During the oxidation of sulfides, nickel metal is not stable except at temperatures higher than 1500°C, well miscible with its sulfide, and is oxidized more easily than copper. Metallic lead looks as stable as copper during the oxidation of the concentrate but Pb and PbS. are much more miscible with each other and the vaporization loss is considerable. In the reductive smelting of oxides, the effects of oxygen potential and temperature on the copper contents in slag are not significant due to the monovalent character of copper and the reduction of copper content in slag is not easy in practice. The effect of the slag compositions on the oxidic metal contents of slag is much more significant for lead than either copper or nickel. Due to the immiscible nature between Pb and Fe, high grade lead bullion is easily obtained and lead is more tolerant to impurities.

Jan 1, 1998

By F. Ajersch, P: Tsantrizos, K: Shanker

"TiN films have been deposited on various substrates by a novel reactive plasma technology. In this process, a nitrogen source (NH3 or N2) and TiCl4 are reacted in the jet of a plasma torch, and are deposited onto a substrate forming TiN films at a high growth rate ( > 2µm/min). It was found that the process parameters strongly affect the microstructure, thickness, density, and growth rate of the TiN films. These parameters include source of nitrogen (NH3 or N2, N/Ti ratio, temperature of substrate, and spray distance. In general, it was found that thick and dense coatings were deposited when the N:Ti ratio was kept low, and the substrate temperature was high. Also, for the series of conditions investigated, NH3 was found to give much better results than N2•. The limitations and advantages of this technique are also discussed in this paper.IntroductionTiN is an extremely hard material and is used in many wear applications, particularly as a protective coating on cutting tools to extend their Iife(1.2). Owing to its excellent chemical stability, TiN is also frequently used as a diffusion barrier in the electronics industry for sub-micron Al/TiN/Si ohmic contact systems (3) or as a coating on high-temperature resistant alloys in gas turbine applications (4), based on its good resistance to oxidation. Other applications include decorative coatings in the jewelry industry, and specialized applications such as solar energy absorbers and transparent heat mirrors(5).TiN films can be deposited/formed using various techniques. The main techniques of deposition are CVD (Chemical Vapour Deposition) and PVD (Physical Vapour Deposition). Each of these techniques can have many variations in equipment characteristics, reactants as well as a range of process parameters (pressure and temperature). In the CVD process, TiN is generally deposited onto a heated substrate where a chemical reaction takes place. The reaction can be one of reduction(6) (e.g.: TiCI4 + 0.5N2 + 2H2 --> TiN + 4HCI), of thermal decomposition(7) (e.g. decomposition of titanium dialkylamide), or of displacement (e.g. TiCI4 + NH3 --> TiN + 3HCI + 0.5CI2)' The displacement and reduction reactions are the most common."

Jan 1, 1994

By Nobuo Takahashi

Effective solvent extraction media have been investigated for purification of rare earths. At first, a quaternary ammonium compound was studied. The counter anions of rare earths and organic dielectric substances were tested to improve separation factors,. And second, crown ethers were selected for extractant. Several diluents of crown-adducts were tested to improve solubility and distribution coefficient as well as the counter anions of rare earths. Especially, in the presence of strong reducing agents, highly selective extraction of europium from other rare earths was observed. The third extactnts were ß -diketones. Presence of organic dielectric substances was very effective to improve separation factors. Though those. three groups of extractants were suitable for mutual separation of light rare earths, alkyl esters of alkyl-phosphonic acids were suitable for mutual separation of heavy rare earths because of their high separation factors. To keep proper pH value was necessary for acidic extractants, so control method of the solution pH was studied with high molecule insoluble amines or salts of those.

Jan 1, 1995

By J. A. Brierley

A biooxidation-heap pretreatment process was field tested to evaluate enhancing gold recovery from a preg-robbing sulfidic carbonaceous ore. Newmont Gold Company&apos;s Gold Quarry sulfidic carbonaceous ore was inoculated with an iron-grown culture of Thiobacillus ferrooxidans to form a 495 ton test heap. Biooxidation was conducted for a period of 100 days. The most active period of biooxidation occurred during the first 40 days of pretreatment? About 35 to 40% of the sulfide was oxidized. The extent of biooxidation was considered good as the ore particle size was relatively large 58% >1?9 cm (&apos;/< inch). The larger particle size ore limited the extent of bacterial activity. The field test demonstrated the ability to conduct biooxidation in a small pilot test heap. Thiourea was evaluated for extraction of gold from the biooxidized preg-robbing ore.

Jan 1, 1995

By Niko Hellstén

To capture efficiently the valuable trace metals from nickel slag using electric furnace, it is important to study their distributions between the slag and metallic phases in the furnace. It is impossible to calculate accurately these distributions without experimental measurements. Therefore, in this work, selected trace metal distributions and phase equilibria between K2O containing iron-silicate slags and a metallic Ni-Fe-Cu alloy in nickel slag cleaning furnace conditions were studied. The experimental method developed and applied during the work, involved a modified quenching technique that included equilibration of the samples in semi-sealed quartz ampoules in an inert atmosphere and metallic Fe saturation. The use of the semi-sealed quartz ampoule prevents the escape of volatile elements from the sample during equilibration. Chemical compositions of the phases and the trace elements were analysed by EPMA. From the measured compositions, the trace metal distribution coefficients between the molten Ni-Fe-Cu alloy and slag were calculated.

By Michael G. Mayer

Since its invention in 1859 various designs of lead batteries have evolved to meet commercial needs for traction applications and standby power. In recent years major developments have taken place in lead alloys and the chemistry and mechanical design of industrial lead batteries. These are reviewed in relation to their commercial application together with the new type of maintenance free gas re-combination lead-acid batteries which are opening so many new markets for lead.

Jan 1, 1990

By N. Kanari

One of the criteria to define the market value of chromite concentrate is its chromium to iron ratio. Changing this ratio for a definite chromite mineral is impossible by physical processing. This study investigated the possibility of increasing this ratio through the carbochlorination and the oxychlorination of chromite concentrates. Experiments are carried out up to 1000 °C. The characteristics of samples and reaction products are determined by SEM, XRD and chemical analysis. The carbochlorination of a chromite concentrate at about 600 °C leads to the . selective partial elimination of iron allowing a higher Cr/Fe ratio of the treated concentrate. Selective extraction of iron could also be achieved at about 950 °C by oxychlorination. In this case, a part of chromium contained in the concentrate is recovered as chromium oxychloride. The obtained residue had high content of Cr, Mg and A1 oxides. Such material has probably better chemical and thermal properties that may. be useful for foundary and refractory applications. Two flow-sheets for the beneficiation of the chromite concentrates using carho- and oxychlorination are suggested.

Jan 1, 1997

By George P. Demopoulos

n this study we have sought to highlight the critical linkage between individual reaction kinetic parameters (usually determined in small bench scale experiments) and large continuous reactor performance by focusing on the industrially significant zinc pressure leach process. To this end a comprehensive mathematical model previously developed for the description of this process was employed. In this paper we have examined in particular how small variations in key kinetic parameters impact on the autoclave&apos;s performance, i.e. attainment of autogenous steady-state temperature, zinc conversion and solution chemistry. The reaction parameters studied were: (i) stoichiometry of the marmatite leaching reaction; (ii) the activation energy of the same reaction, E,; (iii) the rate constant of the ferrous to ferric oxidation reaction, k,; and (iv) the apparent equilibrium constant for ferric precipitation, K,. This parameter sensitivity analysis was done under no oxygen mass transfer control limitations. Model predictions were found to be more sensitive to the kinetic parameters under certain conditions than others. The most dramatic finding was the one related to the small amount of sulfate produced during marmatite leaching. In connection to this it was found that the small percentage (< 5 %) of sulfate produced enhances the autothermal operational stability of the autoclave. The need for accurate kinetic parameter determination under conditions similar to those encountered in industrial zinc pressure leaching was demonstrated.

Jan 1, 1999

By Jorge Alberto Soares Tenório, Romano Espinosa, Felipe Fardin Grillo, José Roberto de Oliveira, Denise Crocce

"The aim of this work was evaluation of the recovery of Zn and Fe of the EAFD added to the hot metal in the form of briquette at temperature of 1500°C. The EAFD was agglomerated by cold briquetting and introduced in the hot metal. This study utilized a bench-scale equipment to melt, during this process to kept a flow rate of inert gas above the bath. Were collected periodically metal samples and the samples were analyzed for determination of the content of total silicon and carbon by chemical analysis. Zinc oxide, zinc ferrite and other oxides were reduced and were volatized and collected by a cleaning system of dust (baghouse) located on top of the oven. More than 98% of iron were recovered from EAFD during the test. It was possible to produce a dust containing about 68% zinc by means of adding of EAFD.IntroductionIn the first semester of 2010, steel production was about 706 million tons, 27.9 % more than in the first half of 2009. Not a significantly increase if 2010 data is compared with the first semester of 2007 (only 7.2 % higher), before the world’s economic crises. Steel production is divided into two main routes. The first one, and most used, is the Basic Oxygen Furnace Process (BOF process), which in 2008 accounted for approximately 67.1 % of steel production. The second route is carried out in the Electric Arc Furnace (EAF) that in 2008 represented 30.6 % [1 ].Electric arc furnace dust (EAFD) is a solid waste generated during the steel making process. It is classi?ed according to NBR 10004 as dangerous solid waste-class I, because the elements Pb e Cd leach in water exceeding the maximum limits permitted by the NBR 10004 [2 ]."

Jan 1, 2012

Primary sulphidic gold ores in the Archean provinces of Western Australia can be broadly sub-divided into pyritic, pyrite-telluride, arsenical and antimonial types. Pyritic ores contain only native gold, and are essentially not refractory. Arsenical ores almost always carry some invisible gold, and may vary from mildly to highly refractory. Pyrite-telluride ores contain gold-bearing tellurides, and are refractory to varying degrees. Antimonial ores usually contain aurostibite, and may be very difficult to process. A classification scheme for metallurgical processing, based on mineralogy, is proposed for the ores, and implications for processing are discussed.

Jan 1, 1995

By Nobuo Kikumoto

Recently, the treatment of industrial waste materials has been a serious social problem here in Japan. Filling them in ponds is now strictly prohibited due to a limited land area and incineration method is also regulated as not to generate DXN. In these conditions, Onahama Smelter has begun to treat shredder dusts (SD) of car at reverberatory furnaces to recover various metals such as copper, gold, silver and palladium without generation of DXN. The total volume of these dusts is expected more than 1 million metric tonnes a year in Japan. Onahama Smelter is now planning to treat about 20% of them in the near future by using tonnage oxygen. In this paper, the heat balance, control method of DXN and treatment of these dusts in reverberatory furnaces are described. DXN : Dioxin (The generic term of PCDD and PCDF)

Jan 1, 2000

By D. McConchie

Management of caustic red mud wastes at the QAL bauxite refinery uses an innovative approach . involving neutralising the red mud with seawater; solids settle in a Red Mud Dam and residual water (pH = 8.6) is discharged to a tidal inlet. A survey of 18 trace elements in sediment, water, mangroves and molluscs, and an ecological survey of benthic fauna in the inlet, and at near-pristine control sites, revealed no significant trends that were linked to the discharge, except for the concentration of Al which was slightly elevated within 100m of the outfall. Trace element concentrations in water samples were close to, or below, world average seawater values and oysters collected near the outfall were acceptable for human consumption. The impact of discharges is minimised by a high tidal range, >60% flushing of the inlet in each tidal cycle, and the very high trace element binding capacity of sediment in the dam (> 100meq/ 100g dry mud).

Jan 1, 1996

By K. Morsi, S. K. Kassegne, A. El-Desouky, K. S. Moon

"Current Activated Tip-based Sintering (CATS) is a new process for the powder-based fabrication of macro, micro and possibly nano-scale features and shapes. This new and unique process enables selective sintering of powders by localizing electrically activated sintering conditions through a stationary or moving electrically conducting tip. We present preliminary experimental results on the effect of tip size in the CA TS process as well as the effect of initial powder particle size on the sintering behavior of nickel powder.IntroductionSpark Plasma Sintering (SPS) has been the center of attention of numerous researchers due its noticeable advantages over conventional sintering techniques such as rapid heating rates, lower sintering temperature and shorter holding times. Research on SPS has been applied on a wide variety of materials such as pure metals [ 1], ceramics [2], composites [3], nano-materials [ 4], biomaterials [ 5], shape memory alloys [ 6] and many other material systems. However, it has been mostly limited to bulk materials with simple shapes with a few exceptions ofresearch efforts where the effect of electric current was combined with metal forming processes such as spark plasma extrusion [7,8] and electric rolling of powders[9]. In this paper a novel process (Current-Activated Tip-Based Sintering (CATS)) is discussed where electric current and pressure are applied simultaneously through a small conducting tip (stationary or moving) over a conducting powder compact. This process has the potential advantages of sintering complex geometries with minimum energy requirements as unconventionally high current densities can be achieved due to the small contact area between the tip and the powder compact. Furthermore, by controlling the tip size, it can be possible to sinter features on the macro-, micro- and even nanoscales."

Jan 1, 2011

By Bhagyadhar Bhoi, Chitta Ranjan Mishra, Hara Prasanna Mishra

"In the Sukinda Valley of Orissa, India, the total quantity of nickel ore reserves comprising of both lateritic and chromite over burden(COB) have been estimated at around 231 million tonnes containing 0.3 to 0.9% Ni. While mining of one tonne of Chromite ore, around 6-7 tonnes of chromite over burden are removed. These overburden materials are disposed as waste materials, which causes lot of environmental hazards and ecological imbalance. India imports a large amount of nickel and ferro-nickel to meet its growing demands in various sectors. For import substitutions, efforts have been made to produced ferro-nickel from the lean deposits of nickel bearing lateritic ores/ chromite over burden materials by reduction roasting followed by magnetic separation and then the nickel rich magnetic fraction is smelted to produce ferro-nickel. It has been possible to produce ferro-nickel of grade varying from 4-25% nickel.IntroductionDuring mining of chromite ore, large quantities of overburden materials are being generated. The materials amount to approximately 10 million tones per year contain around 0.3-0.9% Ni, 0.02-0.06% Co, 20-50% Fe and 4-9% Cr2O3 depending upon the location and the depth of the mine. These materials presently do not find any application for the extraction of nickel due to lack of a suitable technology. The materials are also unsuitable for ferro-nickel making because of their very high iron to nickel ratio. The country is seriously looking for a suitable technology to utilize these resources as its entire domestic requirements of nickel is met though imports. In this connection, a systematic approach has been made at the Institute of Minerals and Materials Technology, Bhubaneswar to develop a process for ferro-nickel making from this indigenous resource."

Jan 1, 2011

By Robert Mensah-Biney

The loading characteristics of gold-tetrabromide species onto a weak-base resin, PAZ-4, were evaluated using a completely mixed batch reaction system. The time. to attain equilibrium loading was substantial, on the order of several days. However, abnormally high loading capacity values of 15 to 20 meq Au/g dry resin (1000 to 1300 kgAu/tonne) were attainable in 24 hours. The loading of gold-bromo species by P AZ-4 was visualized as consisting of two processes: (i) the rapid adsorption of [AuBr4r species by simple ion exchange mechanisms and (ii) reduction of [AuBr4r to metallic gold by an electron exchange mechanism. Elution of gold from loaded resin was feasible provided the resin had not been loaded to high capacity values. If loading is carried to high levels, complete elution becomes impractical and the gold may be recovered by ashing the loaded resin. For the high loading capacities observed this option would appear to be cost effective.

Jan 1, 1991

By P. R. Taylor

Diamond films have been successfully formed in an inductively coupled plasma (ICP) chemical vapor deposition (CVD) system from several gas mixtures: CH,-H,, C2112-112, and C2112-112-02&apos; Our previous thermodynamic study indicated that the substrate temperature could be lowered by the presence of oxygen species at moderate system pressures (0.3-0.5 atm) and that higher volumetric growth rates required a high temperature source and a moderate pressure system in CVD processing. The principal experimental results were consistent with the thermodynamic predictions. The deposited films were characterized by laser Raman spectroscopy, scanning electron microscopy, and X-ray diffraction. The films were well faceted and uniform, with the growth rates over 10 pm/hr on molybdenum substrates. The crystal size ranged between 1 and 2 microns for a two hour experiment. It was possible to decrease the substrate temperature to below 800 °C in this system.

Jan 1, 1995

By F. F. Aplan, G. Simkovich

"A review is given of the effects of solid state point imperfections upon a number of mineral benefication processes and a metal extraction process. It has been found in numerous flotation studies that small amounts of aliovalent impurities (dopants) in binary compounds may show major effects upon flotation behavior. Both semiconducting and ionic conducting compounds are affected. These effects are also seen in hydrometallurgical studies as well as in electrostatic operations. Additionally, de-copperization of lead melts appears to be strongly influenced by similar defects. It is hypothesized that the effects observed in these studies are present in actual operations and should be considered in designing processes. A few speculations concerning future efforts are advanced. IntroductionImperfections [point (e.g., vacancies, interstials, quasi-free electrons, electron holes, impurity ions), line (e.g., dislocations), two dimensional (e.g., grain boundaries) and three dimensional (e.g., 2nd phases) defects] are generally present in solid materials and these imperfections may, and often do, have important effects upon a variety of properties and processes. In general, one may, in most cases, attain elimination of three dimensional defects by a separation process of one type or another (e.g., gravity, electrostatic, magnetic, flotation, hydrometallurgical etc.,). Thus, this type of defect has rarely been investigated in a systematic fashion. Two dimensional defects are always present in non-single crystal materials but have also escaped systematic studies in processes primarily because the control of such defects is not easily attained. Line defects are non-equilibrium entities which are present in ill-defined quantities so that they present a variable that cannot be easily controlled although through careful systematic experiments one can attain some reproducible relations pertaining to this type of defect.Contrary to the lack of studies concerned with the effects of 1, 2 and 3 dimensional types of defects there has been some activity concerned with point defects and their effects upon a number of mineral/metallurgical processes, especially flotation processes. Thus, this article will present a review primarily of point defects in relation to their effects upon flotation although other processes and defects will also be mentioned."

Jan 1, 1988