Search Documents

By Frame Ritzert, Dennis Keller, Vijay Vasudevan, David Arenas

"An investigation was conducted to describe topologically close packed (TCP) phase instability as' a function of composition in the advanced ·Ni-base superalloy Rene N6. TCP phases are detrimental to overfill high-temperature performance of Ni-base superalloys because of their brittle nature and because they deplete the Ni-rich matrix of potent solid solution strengthening elements. Thirty-four variations of polycrystalline .Rene N6 determined from a design-of-experiments approach were cast and homogenized at 13 l5°C for 80 hours followed by exposure at 1093°C for 400 hours to promote TCP formation. The alloys had the following composition ranges in atomic percent: cobalt 10.61 to 16.73, Mo 0.32 to 1.34%, W 1.85 to 2.52%, Re 1.80 to 2.11%, Ta 2.36 to 3.02%, Al 11.90 to 14.75%, and Cr 3.57 to 6.23%. Physical and chemical characteristics of all microstructures obtained were described using various analytical techniques. From these observations, a mathematical description of TCP occurrence (s and P phase) was generated for polycrystalline Rene N6.IntroductionNi-base superalloy single crystals represent the state-of-the-art for turbine engine airfoil application as they offer the best balance of properties to allow for the high operating temperatures required: for efficient engine operation.1 Current trends in alloy design take advantage of improved creep rupture strength with the addition .of higher levels of refractory elements. 2 In .particular, the addition of significantly higher levels of Re in third generation superalloys is key for both microstructural stability and creep rupture strength. 3 While the presence of the refractories is thought to provide strength benefits from solid solution hardening, a tendency for alloy instability in the form of topologically-close-packed (TCP) phases or secondary reaction· zone (SRZ) ·phenomena accompanies the high refractory content. 3 The formation of these phases in sufficient amount is detrimental to the overall high temperature performance of Ni-base superalloys because of their brittle nature and because they deplete the Ni-rich matrix of potent solid solution strengthening elements.4 The tendency for a particular composition to form TCP may not be immediately known since the precipitation of TCP phases in Ni-base superalloys is nucleation controlled, thereby requiring long times at elevated temperatures to precipitate. 5 They preferentially nucleate along the octahedral planes of the Ni-base superalloys, usually in areas of refractory metal enrichment at grain boundaries or inside dendrites.5-6 In Rene N6, two closely related TCP phases, a and P, have been observed.2"

Jan 1, 1998

By J. M. Demarthe

MINEMET RECHERCHE (IMETAL Group, formerly Le Nickel-Penarroya-Mokta) has studied on a laboratory scale and patented a new process to recover metal values -copper- from sulphide ores and concentrates. It combines a cupric leaching, solvent extraction and copper sulphate electrowinning according to the main following steps - A direct and selective leaching of copper sulphide ores or concentrates at atmospheric pressure with cupric chloride to form cuprous and ferrous chlorides and elemental sulphur. Pyrite remains in the sulphur residue. - The leach solution is separated into two parts -In the first one, air is injected to precipitate iron as goethite. The oxidation step can be easily realized at atmospheric pressure by maintaining an excess of cuprous and-ferrous chlorides in the liquor. Copper is extracted from the second part as cupric ion by an LIX reagent. Direct injection or air in the mixing chamber maintains good extraction conditions, so that only one mixer settler is required. - Iron, in the form of ferrous ion, is not coextracted. - Copper is stripped from the organic phase, transferred into a sulfuric phase and sent to sulphate electrowinning cells, which are now conventional in copper metallurgy. - Only electricity and air are required. After a feasibility study, the next step will be to develop it on a pilot and commercial scale.

Jan 1, 1976

By Masao Miyake, Eiichiro Matsubara, Tetsuji Hirato, Yasuhiro Awakura

"Zn-Cr alloy coating with around 15 wt% Cr has been found to have much higher chemical corrosion-resistance to steel than conventional zinc plating, while· its structure has not been clarified. The Zn-Cr alloy plating is performed at high current densities around 1 A cm-2 and for 10 to 20 sec using acidic aqueous sulfate solutions with some additives in the iron-steel industry. Due to the high current densities, it seems reasonable to consider that the Zn-Cr alloy plating proceeds under an unsteady-state condition and that the resulting coatings have a non-equilibrium phase and have a structure change in the .direction of thickness. In this research, the crystal structure of the Zn-Cr alloy coating electrodeposited at high current densities and change of the structure in the direction of thickness were examined by X-ray diffraction. The coatings containing under 20 and 35-40 wt% Cr had hcp and bee structure, respectively, while the coatings containing 20-35 wt% Cr comprised two phases with the hcp and the bee structure. The structure of the coating varied in the direction of thickness; both the hcp and bcc phases coexisted in the vicinity of the substrate, while the hcp phase became predominant with increasing distance from the substrate.IntroductionRecently it has been reported that Zn-Cr alloy coating containing around 15 wt% Cr has much higher corrosion-resistance to steel than conventional zinc plating.1-3) The corrosion-resistanc·e of Zn-Cr alloy plated steel sheet with a plating amount of 20 g m·2 is, for example, superior to that of Zn plated steel with a plating amount in the range 60 to 90 g m·2 , which is widely used for automotive bodies today.4l The Zn-Cr alloy plating is obtained by electrodeposition at current densities over 0.5 A cm·2 from a sulfate solution containing zinc and trivalent chromium ions and some additives.5•6) The deposition current densities mentioned above are much higher than those for usual electroplating processes, e.g., Zn, Cu and Ni plating, carried out about 0.05 A cm·2 • Therefore, the time required for plating is very short; around 10-20 sec. Due to the high current densities, it seems reasonable to consider that the· Zn-Cr alloy plating proceeds under an unsteady-state condition and that the resulting coatings do not have a phase expected from equilibrium diagrams; no phase diagram of the Zn-Cr system with a full composition range has been available. 7). In other words, the alloy phase plated would be a non-equilibrium phase with unknown structures."

Jan 1, 2000

By Shinya Hodoshima

A catalysis pair of tetralin dehydrogenation / naphthalene hydrogenation has been proposed in the present paper as a liquid organic hydride for operating stationary fuel cells. Catalytic naphthalene hydrogenation, having been commercialized since the 1940s, proceeds to generate decalin via tetralin as an intermediate. The storage capacities of tetralin (3.0 wt%, 28.2 kg-H2 / m3) are lower than decalin (7.3 wt%, 64.8 kg-H2 / m3) but both tetralin dehydrogenation and naphthalene hydrogenation are much faster than the decalin / naphthalene pair. Moreover, existing infrastructures such as gas stations, chemical tankers and tank lorries are available for storage, transportation and supply of hydrogen. With respect to the stationary fuel cells with large space for hydrogen storage, tetralin as a hydrogen carrier is superior to decalin in terms of fast hydrogen supply or power density. Rapid hydrogen supply from tetralin under mild conditions was only accomplished with the carbon-supported metal catalysts in the ?superheated liquid-film states? under reactive distillation conditions. In contrast to the ordinary suspended states, the catalyst layers superheated in the liquid-film state gave high catalytic performances at around 250OC. As a consequence, both serious coke formation over the catalyst surface and excessive consumption of exergy were prevented simultaneously.

Jan 1, 2006

By J. Grogan

Leaching of galvanized steel coatings allows the steel substrate to be used as a zinc-free scrap source to steel and iron furnaces. In this study the behaviors of sulfuric acid leaching solutions are investigated. The ranked significance of the variables are shown to be acid concentration > temperature > zinc concentration. Examination of the leaching mechanism finds the rate-limiting step to be the cathodic hydrogen reduction reaction. This rate is not only influenced by acid concentration, but also by the hydrogen reduction exchange current density. Dezincing leaching rates are improved by taking advantage of the higher exchange current density of the iron substrate versus the zinc coating. This is accomplished in practice by increasing the exposed interfacial zinc:iron surface area through shredding. Also, a leach control mechanism is proposed through online monitoring of the zinc-iron couple mixed potential.

By T. T. Chen

The manganese oxide scales, consisting mainly of MnO2, characteristically occur in banded colloform structures which adhere to porous layers of PbSO4 and PbO2 that oxidized from the rolled Pb-0.7% Ag anodes. Hydrous Mn oxides, Mn3O4 and amorphous Mn oxides are believed to be also present. Tiny particles of gypsum, PbSO4, SrSO4 and AgCl are entrapped in the colloform masses. The gypsum originated from the Zn electrolyte; strontium carbonate was added to the ZnSO4 solution to control Pb, and silver originated from the anodes. Some of the colloform bands contain minor amounts of Pb, implying a limited degree of dissolution of the Pb during electrolysis. Other colloform bands incorporate trace amounts of Zn. Colloform structures permeated with silica gel are presumably caused by the high silica content of the electrolyte.

Jan 1, 2009

By Yousef Mohassab, Manoranjan Misra, Monalisa Panda, Eman Wahbah

This work studies the removal of arsenic (V), arsenate, and arsenic (III), arsenite, from aqueous solution using calcined Quintinite-3T. The two adsorbents Quintinite-3T was prepared, calcined at different temperatures, and characterized by XRD, BET, and SEM. The surface area of the calcined Quintinite-3T was 193.4 m2/g. The particles size ranged from 12 to 56 nm for the uncalcined Quintinite-3T and from 24 to 42 nm for the calcined Quintinite-3T. Kinetic analysis, adsorption isotherm, and factors affecting the adsorption were investigated. Calcined Quintinite- 3T retained As(v) and did not release it back to water even after an entire month.

Jan 1, 2016

By Mitsuru Tanahashi

In order to develop an effective process for the production of from metallurgical-grade one (MG-Si), the oxidation removal of boron from molten MG-Si was investigated at a solar-grade silicon (SOG-Si) 1773K by the following two CaO-saturated CaO-CaF2 flux treatment processes. I) Boron removal by flux addition onto the molten M6-8 followed by oxygen gas injection into the melt (Two-stage connecting process). II) Boron removal by simultaneous injection of flux powders and oxygen gas into the molten MG-Si (Simultaneous injection process). These processes can establish the special condition of both high basicity of the flux and the high oxygen partial pressure at the boron removal reaction sites. Through these processes, especially by the simultaneous injection Process using a flux powder injection equipment, the boron content in MG-Si can be efficiently reduced. The obtained results clarified that both processes should be conducted for a time period as short as possible by using as much flux as possible. By repeating the simultaneous injection process for 60 s three times under the optimum operating conditions determined in the present study, the boron content in MG-Si can be reduced from 14 to 4.7 mass ppm.

Jan 1, 2003

By Jan Yaozhong

The composition and the possible utilization of Ti bearing blast furnace from a titanomagnetite blast furnace smelter were studied. The slag contained about 20% Ti02 and trace Sc. The mineralogical analysis indicated that Ti in the slag is mainly as perovskite. By means of magnetite separation, the Ti containing phase could not be enriched. An effective hydrometallurgical approach was proposed with sulphuric acid leaching. The method proposed for processing the studied slag renders product Ti02 and SC203. Besides the recovery ofTiO2 and SC2O3' the leaching process yields fine grained residues which can used as additives for making cement.

Jan 1, 1996

By J. M. Skeaff

As much as 100% of the gold and 67% of the silver in a sulphur-bearing hydrometallurgical leach residue have been transferred to copper metal at copper smelting temperatures by dissolving the partially calcined residue in an iron-bearing slag maintained in equilibrium with the liquid copper metal and matte phases. The precious metals can then be recovered by conventional refining techniques. Copper can be recycled at least four times without any detrimental effects on gold and silver transfers and recoveries. Apparent copper recovery in the .process can be over 100% because of the copper content of the residue. Based on slag analys.es, the overal1 recovery of gold in the copper metal and matte phases varies from 94% to 100% under all conditions investigated. On the? same basis, silver recovery varies .from 9S% ?to 99% under optimum conditions, but is only 4S% to 73% under other, less attractive conditions. Unaccounted for silver losses of' about 30% make it difficult to determine the major factors affecting ?silver transfer and recovery. A method for implementing the technology on a commercial scale at a Canadian copper/zinc smelter has been proposed. A preliminary economic assessment and comparison of the proposed pyrometallurgical process with conventional cyanidation indicates that either process is economically attractive for recovering gold and silver from leach residues. Although the capital costs are higher, the pyrometallurgical process is simpler, has higher recoveries, lower operating costs and no .potential environmental problems related to cyanide disposal.

Jan 1, 1989

By S. Ozbilen

"Al-Li binary alloys with nominal Li contents of0.15, 1.1and2.8 (in wt%) were aged naturally at room temperature for two months, aged at low temperatures ( 65 and 1 OOEC) for up to 2 months and aged artificially at 190EC for 4 days after water quenching to 25EC following solutionizing at 530EC for 20 minutes. Ageing behavior of these binary alloys were studied by Vicker's Hardness measurements and DSC thermal analysis. Thermal analysis results indicate the formation of GP zones of Al-Li system in Al-2.8wt%Li binary alloy. In the same alloy, rapid quenching from one phase region (a) gives rise to precipitation of small o' particles in a matrix (a) with still high supersaturation. During ageing of this alloy below lOOEC an additional transformation, i.e., GP zone formation occurs proceeding at a very high rate which is described on the basis of the theoretical analysis for the quenched Al-Li system proposed by Khachaturyan et al [6]. Ageing at temperatures below 11 OEC takes place slowly by the formation of small d' particles of lower thermal stability than the quenched-in d precipitates in addition to GP zones resulting in an increase in hardness compared to water quenched samples. During artificial ageing, GP zones transform by dissolution to d' precipitates while d' particles already in the microstructure coarsen during under aged condition at which hardness increases with time till peak aged condition.IntroductionIn binary Al-Li alloys the d' (Al3Li) fully coherent internally ordered inetastable phase of Li2 structure with a=0.4038d [1-5] forms homogeneously between 120 and 190EC before the formation of stable d' (A!Li) phase and cause the superior mechanical properties. This is due to an appreciable age hardening effect resulting because of the d' precipitation during ageing [1]. The response of d' to decomposition and its formation kinetics have been studied previously and it is believed that the decomposition of the a-supersaturated solid solution occurs in a two stage process; i.e., a 6 d' (Al3Li) 6 d(A!Li). Khachturyan et al [6] theoretically investigated precipitation of the d' phase and gave an interpretation of the transformation paths of the quenched Al-Li alloys. They predict that the disordered supersaturated solid solution congruently orders, and then the uniformly ordered solution decomposes into ordered regions that differ in Li-content. Finally, ordered d' phase forms in the disordered matrix."

Jan 1, 1998

By Ramana G. Reddy

Thermodynamic modeling and experimental study on impurity capacities and their distribution between mattes or metal and slags in smelting, converting and refining of non-ferrous metals was discussed. A brief review on the recent developments in copper smelting and converting is presented. The analysis showed that, copper smelting capacity increased by a factor of 10 since 60's, smelting rate increased by a factor of more than 5 and process fuel equivalent decreased by a factor of 2. A thermodynamic model for prediction of impurities capacities in slags and their distribution in mattes and slags was developed. The impurities capacities (i.e. sulfur and arsenic) of slags were calculated a priori with no adjustable parameters using the Reddy-Blander model. The capacities predictions were made in a wide range of matte and slag compositions, PSo, and temperatures in conditions pertaining to copper and lead industrial slags. The calculated results for sulfide and arsenate capacities are in good agreement with the available experimental and industrial copper and lead industrial slags data. The sulfide and arsenate capacities in copper slags (fayalite, ferrite and olivine) and lead slags are reviewed. The application of RB model predicted ratios of O2 and S2 partial pressures in industrial copper smelting processes are discussed. Application of this model for the prediction of Sb, Bi and other impurity capacities and their distribution ratios in mattes or metal and slags, in industrial smelting and refining processes is discussed.

Jan 1, 2003

By Hirokazu Narita

The extractability for Pd(II) using MOTDA and DHS and their durability against a mixed solution of HNO3 and HCl was investigated by solvent extraction and FT-IR measurements. Both MOTDA and DHS selectively extracted Pd(II) over Pt(IV) from 0.75 M HNO32.25 M HCl solutions. The extraction rate of Pd(II) with MOTDA was much greater than that with DHS. In the durability test, the extraction percentage of Pd(II) and the FT-IR spectra were measured using MOTDA and DHS after stirring with 0.75 M HNO32.25 M HCl solutions. The extraction percentage of Pd(II) with MOTDA hardly changed during the two-month stirring; however, that with DHS decreased with an increase in the stirring time. The FT-IR spectra showed the sulfoxide formation by the oxidation of the sulfide in DHS, but not in MOTDA. Consequently, it was found that MOTDA is more durable than DHS.

Jan 1, 2006

By Djona M. Gaballah I.

Selective chlorination of unroasted and roasted spent hydrorefming catalysts was studied between 300 and 600°C using the following gas mixtures : C12+CO, C12+N2 and CI2+air. Such materials contain Co, Ni and Mo compounds supported by alumina and/ or silica. They also contain variable amounts of V compounds, C, S, etc., accumulated during the life time of the catalyst. Direct oxychlorination of the C+S rich sample allows higher extraction rates than those obtained by the carbochlorination of the same roasted one. It seems that the roasting step doesn't favor the economic metals' recovery. Results of the chlorination of C+S poor spent catalysts, in the presence of CO, in the chlorinating gas mixture, or of carbon added to the sample, were comparable. Cobalt and nickel chlorides were .extracted from the chlorination residues by their dissolution with acidified water, whereas molybdenum and vanadium chlorinated compounds were recovered by selective condensation from the vapor phase. The recovery rates of valuable metals as well as the selectivity were higher for the chlorination of spent catalysts than results obtained by the hydrometallurgical processing of the same sample. Results of the scale-up of the oxychlorination of the unroasted sample confirmed those of the laboratory scale. The global recovery rates were about 88 pct of cobalt, 93 pct of molybdenum and 76 pct of vanadium. The carbochlorination was applied to the recovery of W and Ti from Denox catalyst that is a carbon and sulfur free one. Recovery rates higher than 99 pct at temperatures lower than 500 °C could be obtained. This may indicate that the chlorination process can be applied to the treatment of various industrial wastes or by-product containing transition and/or refractory metal compounds A flow - sheet for the pretreatment of these materials is proposed.

Jan 1, 1995

By George Kazonich

The high costs and environmental problems associated with making iron and steel in the United States is driving the development of new technologies to replace the blast furnace. A prototype reactor incorporating rocket technology was designed and built. This rapid rate reactor was operated successfully and consistently made iron metal. Minus 325-mesh magnetite particles could be reduced to iron metal in less than 50 ms in a high temperature flow through reactor. Iron product was recovered inside the reactor and in a downstream cyclonic separator. The results of typical operation and how parametric changes affected the reduction of iron ore concentrates are discussed.

Jan 1, 1993

By David Cocke

Study of surface and subsurface interfacial chemistry of metallic and similar systems has its enormous technological importance. Copper, for example, is a common component of many alloys and bulk amorphous systems. It is being increasingly studied today because of its use for electronic interconnect systems where processing is done below 200 ºC. Since several types of copper oxides exist, and the degree of their formation is dependent on temperature, perhaps characterization by EDS-SEM depth profiling and EIS might delineate one type of oxide from another. In this paper, we described our work on transformation of copper oxides with temperature ranging from 70 to 350 °C and their characterization by SEM, EDS, and XRD. We also showed the use of the phase angle portion of the impedance as a means to identify the predominant structure and the transition through Cu3O2 between the predominant stable CuO and Cu2O.

Jan 1, 2009

By Shengli Wu, Laixin Wang, Minyin Kou, Xinliang Liu, Weidong Zhuang, Yujue Wang

COREX process has obvious advantages in environment protection but still has some disadvantages, for example, it has a higher sulfur content of hot metal than blast furnace. In this paper, the thermodynamics and dynamics of desulfurization have been investigated to obtain the main operation parameters related to the mass fraction of sulfur in the hot metal. In addition, statistical analyses have been carried out to study the relationship between operating parameters and sulfur content of COREX hot metal based on actual plant data. It has been found that the mass fraction of sulfur in hot metal is significantly influenced by the C content in hot metal, MgO/Al2O3 in slag, the concentration of MgO in slag, the temperature of hot metal and binary basicity (R2).A linear model has been developed and subsequently used for reducing the mass fraction of sulfur in hot metal, improve the quality of hot metal and contribute to low carbon ironmaking.

Jan 1, 2016

By M. F. El-Demerdash

The activity distribution diagrams for different species in aqueous systems are developed. Computational method may be considered as an extension of the Activity-Term method introduced by the authors to construct EH-pH diagrams. In the Activity-Term method, all activities of different species are evaluated before deciding the most stable one. In the present study, a factor is assumed to allow for the conservation of the element. At any point, the total concentration of all species should contain only the input m moles of the element (elements) considered. This approach is applied to Zn-, 5-, and Zn-S-H2O and activity distribution diagrams are plotted as a function of pH, at different potential levels and at different temperatures.

Jan 1, 1990

By B. K. Chakrabarti

Modeling and a screening design of experiment (DOE) was performed with the process variables to identify the greatest effect of variables on the response quality in the dead burning of magnesite refractory in a rotary kiln. Among various interdependent variable factors, the design variables chosen were raw magnesite (RM) feed rate, kiln rotation time i,e, seconds per rotation(SPM) and burning zone temperature (BZT). The response variables chosen were exit gas temperature and density of dead burnt magnesite(DBM). ANOVA and normal plots were used to evaluate the effects.This work had enabled to correlate the BZT, RPM, RM feed with the exit gas temp and density of magnesite produced. The result opens up an avenue to look into the optimum region of operations within the ranges of variables considered in order to conserve energy and to minimize the exhaust gas temperature and to maximize the density of the DBM produced

Jan 1, 2015

By T. Wang, R. G. Reddy, D. Mantha

"A new eutectic LiN03-NaN03-KN03-KN02 quaternary molten salt system was calculated using thermodynamic modeling. The eutectic temperature was predicted to be 100°C. The melting point and heat capacity of the salt eutectic composition were determined using DSC. The experimentally determined melting point is in excellent agreement with the predicted value. The melting point is more than 124°C lower than that of the KN03-NaN03 solar salt. The density of the molten salt was experimentally determined as function of temperature. Using the density, heat capacity and the melting point, thermal energy storage density and gravimetric storage density of the quaternary molten salt were calculated and compared with that of solar salt. The larger storage density value of this molten salt indicates that this salt has a better energy storage capacity for solar power generation systems.IntroductionMolten salts have been used as thermal energy storage media for solar energy applications. Nitrates are being used in the solar energy applications for their low melting point, low unit cost, high heat capacity, high thermal stability, negligible vapor pressure and high energy storage density [l]. Solar salt (NaN03/KN03: 60/40) is the most popular thermal energy storage medium which is currently being used with the freezing point of 221 ·c [2]; another ternary system HITEC® which contains NaN03, KN03 and NaN02 has freezing point of 141°C [3]. Newer nitrate salt mixtures are being studied and projected as potential candidates for thermal energy storage (TES) and heat transfer (HT) applications. Based on these favorable features, molten salt can work directly as the energy storage medium below 500°C [l]. Development and synthesis of newer molten salt mixtures with freezing point lower than those currently used for thermal energy storage applications is necessary for sustained utilization of solar energy. The approach to develop lower freezing point molten salt mixtures is by the prediction of new eutectic mixtures and also by the development of new nitrate compounds."

Jan 1, 2012