Search Documents

By Peter Cain

In response to the appearance of excessive convergence of bolted gateroads in the front abutment zone of retreating coal faces at Phalen Colliery, staff from the CANMET Cape Breton Coal Research Laboratory in Sydney, N.S. initiated a programme of roof profile measurements in the front abutment zone of longwall headgates. The results of these measurements allowed a characteristic deformation curve to be determined for each headgate, and the early identification of areas showing an unstable deformation trend. These areas were then reinforced with supplementary support. The monitoring programme was adopted and enlarged by the rock mechanics staff of the Cape Breton Development Corporation, and has been continuing for a period of approximately two years. A sufficient quantity of data now exists to be able to make an assessment of the effects of a number of mining parameters on the performance of the gateroad in the front abutment zone. The following paper describes the method of measurement, illustrated by typical results, and goes on to relate variations in rate and patterns of movement to geology, interaction, method of support and pre-mining stresses.

Jan 1, 1996

By Kot F. Unrug

Strength of coal is one of the governing factors in size determination of mine pillars, and therefore affects the percentage of extraction and thus, utilization of reserves. Coal strength is also important from the subsidence control standpoint, where mine pillars with appropriate safety factors should be designed for long term stability. Determination of coal seam strength has been addressed through the extrapolation of the coal strength obtained from a small number of samples on the whole section of the seam. This procedure often gives unreliable results. Presented in this paper is a method of in-situ strength testing of coal, allowing for a realistic determination of seam strength. Results of a field case study dealing with the coal seam, where samples for the laboratory strength tests could not be obtained due to the dense cleat, are presented. However, in these conditions, the in-situ testing was successful. A comparison of both conventional and the in-situ penetrometer method was carried out. It was found that the penetrometer data not only improve the accuracy of strength determination of the entire seam, but also prove to be much more cost effective than the conventional method on a per test basis.

Jan 1, 1995

By J. Nielen van der Merwe

This investigation was done to develop a method to predict the lie of coal pillars. It has long since been known that coal pillars deteriorate over time, but there was no method to quantify the deterioration. It was found that the rate of pillar deterioration was essentially a function of two parameters, namely mining height and time. The higher the mining height, the more rapidly the pillars deteriorated. The rate of deterioration is not constant, but decreases exponentially with time. The pillar life should be viewed in conjunction with the safety factor. While the relationship between safety factor and pillar life is ambiguous, the trend is nonetheless for higher safety factor pillars to have longer lives. The safety factor can be used to quantify a failure probability. The pillar life prediction indicates when the pillars which are predicted to fail, can be expected to do so.

Jan 1, 1998

By X. S. Tan

This paper deals with the analysis of stress condition on the interface between two types of floor rock materials when the vertical stress is larger, or when the horizontal stress is larger in a rectangular opening. It indicates that the floor Failure and the failure stress of floor rocks are closely related. It also demonstrates that a larger horizontal stress is one of the most important factors in increasing the potential for floor rock failure and floor heave.

Jan 1, 1990

By G. K. Rogers

The portal, which is the near-horizontal, surface point of entry to an underground excavation, can often be an exceedingly difficult area in terms of ground control. Surface and subsurface failures at portals, as discerned during a study involving over 300 case histories, are unfortunately, common. To aid in the engineering evaluation of portals, the Geomechanics Classification System was appended with discontinuity orientation assessment values and support/excavation guidelines. Also, a design model utilizing RMR predicted rock loads in conjunction with half-dome theory is proposed for the most common type of portal failure. Other pertinent comments and recommendations relating to portal stability are included.

Jan 1, 1989

By David Forrester

Subsidence beneath the land surface has traditionally been monitored using the most accurate surveying methods of the day. Over the several hundred years of subsidence investigation, these techniques have improved, and thus the accuracy of subsidence measurements has improved. In circumstances where the subsiding surface is masked by water or rock, novel methods must be developed. This method describes the recent successes of subsidence monitoring using advanced bathymeric techniques in the Sydney Coalfield. In order to obtain subsidence profiles above submarine coal extractions, seafloor bathymetry surveys, run before and after mining, have shown that subsidence profiles can be detected, despite the primitive nature of some of the trials. Very recently, there have been considerable advances in this field, associated with the availablity of high-powered personal computers to control data collection and analyse the results. The recent surveys described in this paper have demonstrated the considerable potential for such methods. This paper describes bathymetric subsidence monitoring developed in the Sydney Coalfield, illustrated with some typical results, and summarizes the findings of the research leading to the development of subsidence design criteria specific to the Sydney Coalfield.

Jan 1, 1996

By David F. Gearhart

The Burrell Can1 is a thin, steel, tubular shell filled with aerated concrete that is used as a roof support in coal mines. The Can height is always shorter than the mining entry, so it is capped with wooden timbers and wedges when it is installed. This combination of the Can and the wooden header is a standing support system that is designed to yield in a controlled manner and exhibit a constant yield, or elastic-plastic behavior. The Burrell Can is capable of withstanding 20 in or more of vertical convergence and 15 in or more of horizontal displacement. Because of this exceptional ability to sustain load through extended convergence and displacement, it is one of the most robust standing supports in use today. The National Institute for Occupational Safety and Health (NIOSH) conducted testing on seventeen Burrell Cans in 1995, during development of the support where the ratio of the height to the diameter, or the aspect ratio, was between 2:1 and 4:1. Based on the results of that testing, it was suggested that the standard aspect ratio of the Can be less than 5:1. This suggestion is intended to preserve the overall stability of the Can, which will help to maintain the initial stiffness and prevent load shedding. Recently, the necessity of the aspect ratio has been questioned, and this issue will be addressed in this paper. Since the initial development and introduction, more than 130 tests of the Can have been conducted at the NIOSH Mine Roof Simulator (MRS), and 25 of those specimens had aspect ratios greater than 5:1. The 18-in-diameter by 10-ft-tall specimens had the largest aspect ratio, 6.67:1.However, the aspect ratio is not the only parameter that affects the performance characteristics of the Can. Multiple factors, such as the use of different wood species, the use of different header or footer configurations, and the use of pedestals, as well as biaxial loading conditions can also decrease the stiffness and capacity of the Can. Data from full-scale tests that include these other factors are analyzed to show that the initial stiffness is primarily affected by the roof and floor contact configurations. Furthermore, load shedding is more likely to occur or begin earlier when the aspect ratio is greater than 5:1 and one or more of the other factors are present.

Jan 1, 2012

By Richard D. Begley

This paper summarizes the development of a mechanistic model to predict longwall mining induced surface subsidence. The model was originally developed from data acquired from a recent field study conducted in Northern West Virginia. Additional data has been collected from published sources and used to refine the model. The original model utilizes a negative exponential equation to predict the subsidence profile after the maximum possible subsidence is predicted based on the following input parameters: mine geometry, angle of draw and expansion factors for the deformation zones that have been identified above a longwall excavation. The model refinement involved the development of relationships between physical properties of the overburden strata and angle of draw in addition to the expansion or bulking factors. Therefore the refined model now requires only mine geometry and a typical geologic column from the site to predict the subsidence profile. This paper provides the methodology that enables the model to determine the angle of draw and expansion factors breed on physical properties of the site geology i. e. percent of strong rock and Rock Quality Designation of the overburden strata. In addition :comparisons of predicted results with measured data for over H) different sites with various geological and geometrical parameters located throughout the United States will be presented.

Jan 1, 1989

By Raymond A. Mazzoni

Over the last twenty years, roof support technology has made numerous advances since the original wedge and slotted bolts of the 1950's. By comparison, the roof supports used today are more complex and specialized than the supports used in the past, providing mines with a varied selection of supports from which to choose. As a result, when problems with supports are encountered, it is more difficult to determine whether it is the result of geological changes, poor installation practices, or malfunctioning supports. Recognizing this problem, MSHA's Roof Control Division of the Pittsburgh Safety and Health Technology Center, has undertaken the task of publishing a guide for trouble¬shooting problems encountered with roof support systems. The purpose of this guide is to provide a logical sequence to resolving the most common problems encountered with roof supports. The objective of this paper is to introduce this guide to the mining industry as well as provide insight into the evolution of the guide from its beginnings as rudimentary charts to its more comprehensive present format as a practical guide for use by the mining commu¬nity.

Jan 1, 1997

By Rajagopala Reddy Kallu

After the Sago and Darby No. 1 mine incidents, the new regulatory standards for the design of mine seals in underground coal mines of the United States require the mine seals to withstand higher explosion standards. This necessitated for the development of new design approaches and standards. For development of any new design standards or approaches a detailed understanding of effect of key influencing parameters on the stability of mine seal is a must. This paper attempts to address one of the factors, i.e. roof convergence, that play an important role in the stability of mine seal under explosion loading. Initially a couple of three dimensional numerical models were built and tested for different levels of roof convergence. These models confirmed that roof convergence has great influence on seal stability. A detailed study is undertaken, with some simple assumptions, to establish typical influence of roof convergence on the stability of mine seal under different levels of static explosion pressures. Three dimensional distinct element code 3DEC is used for this purpose.

Jan 1, 2007

By L. J. Lorig

Much of the present knowledge about caving behavior of rock masses has been obtained from empirical observations. Additional notions about caving have been developed through inferences derived from two-dimensional finite element analyses. These analyses have indicated that a combination of one low-angle set of fractures and one nearly vertical set of fractures is the optimum fracturing configuration for ease of cavability of an orebody. This paper presents the results of two- and three-dimensional distinct element analyses which draw different conclusions than those reported from finite element studies. The distinct element method is selected far analysis of cavability because this method treats the rock mass as an assemblage of rock blocks which may interact individually, The results of the analyses are compared to a documented case history which involved a groundfall of 80,000 tons of ore in a 160-foot high pillar. The mechanics associated with these results are-explained in terms of simple static stability analysis of wedges. The propensity for orebody caving is primarily a function of the number of joint sets or potential "release" surfaces in the orebody. This mechanism is influenced by the bounding weak discontinuities, and intact strength of rock material.

Jan 1, 1989

By Dennis R. Dolinar

Screen material in the form of welded wire mesh and geogrids are used in underground coal mines to prevent the fall of small pieces of rock from the roof between roof bolts. Further, if the screen is installed during the production cycle, roof fall injuries can be reduced significantly. Therefore, the National Institute for Occupational Safety and Health (NIOSH), because of the safety implications, conducted an evaluation of screen materials commonly used in U.S. coal mines to determine their support characteristics and identify the parameters that could affect their performance with respect to controlling the fall of rock from the roof surface. To evaluate the load and stiffness characteristics of the screen, a test frame was designed and installed in the Mine Roof Simulator (MRS) at the NIOSH Pittsburgh Research Laboratory (PRL). With this test set up, the screen is bolted at four corners of the frame and a center load is applied. The test set up allows for up to 20 in of screen deflection while the load and screen defection are continuously recorded. A series of tests were conducted to evaluate the effects of various parameters such as bolt tension, the type of load bearing surface and the size of bearing plates on welded screen performance. The most common screen material used in U. S. coal mines is an 8-gauge wire welded in a 4-by-4-in spacing or aperture. The peak screen load was normally limited by wire breakage. The conditions at the bearing plate influence the nature of the wire breakage. However, the screen stiffness was controlled by slippage at the bearing plates, and by weld and wire failure. The size of the bearing plate had a significant effect on the performance of the welded screen. Therefore, the design capacity of the 8-gauge screen is evaluated based on plate size. For a 6-by-6-in bearing plate the average peak load is 2,900 lb with a stiffness of 250 lb/in. For an 8-by-8-in bearing plate, the average peak load is 4,500 lb with a stiffness of 430 lb/in. These test results are based on a 4-by-4-ft bolt spacing. A geogrid mesh was also tested.

Jan 1, 2006

By Wouter Hartman

Xuandong Coal Mine is mining coal in one of the most challenging underground environments in the world. This work has found that it is not only challenging but it also has the composition for some interesting rock mechanics and ground control conditions. The paper highlights the extreme mining and rock mass behavior conditions encountered when mining coal at 900 m below surface. It was found that the ground control environment associated with geological weakness, low coal material strength and stiffness, was reasonably well controlled; however, the chain pillar geometry and design did not take these geological weaknesses into consideration. Some of the chain pillars employed were quite large, which resulted in floor punching and secondary floor heave, which causes extreme difficulty for production. No barrier pillar has been employed except for the center 164-m-wide main headings pillar with a w/h ratio in excess of 40. After assessing the location and geometry of a 200-m-thick dolerite sill overlaying the coal measures, we found the probability of it breaking up into to smaller fragments and producing a larger goaf to be low. Therefore, the influence of the dolerite sill on chain pillar loading is considered small compared to the low coal, immediate floor and roof rockmass strength. It is further recognized that horizontal stresses could be locked up within the dolerite sill, which would likely result in regional bending that would be distributed through the chain pillars. This has, to some extent, already occurred, and the effects have been seen and felt through excessive floor heave, pillar punching, and coal bumps (seismicity). We?ve also found that there was a need to employ basic rock mechanics principals in assessing the stability of future multiple seam mining layouts.

Jan 1, 2012

By Yi Luo

A longwall mining operation went under a tall, self-supporting and free-standing wireless communication transmission tower. In anticipation of that the ground subsidence process might affect the transmission tower, the mining company took a proactive approach to mitigate the expected subsidence influences. The efforts include prediction of surface subsidence process at the location of the tower, assessment of stability, structural integrity and functionality of the tower structures, and design and implementation of mitigation measures. The intension of this paper is to demonstrate the techniques that can be used to assess and mitigate the subsidence effects on tall self-supporting and free standing tower structures.

Jan 1, 2008

By H. Guo

There are a number of methods available for the determination of the fracture toughness of rock. Some of the most recognised methods include the hollow pressured cylinder, the short-rod, the chevron - edge-notched round bar in bending and the disc-shaped compact specimen. Most of these tests are difficult and expensive to conduct. In this paper the simple Brazilian testing of discs for tensile strength has been used to determine their fracture toughness. Tests were conducted on six different rock types and the values of the fracture toughness obtained for each type are in close agreement with the results of the well recognised the chevron edged types. Details of the tests, and analytical validation of the technique, are presented

Jan 1, 1992

By Ming Ju Liu

China has been suffering from the most serious coal and gas outburst accidents. The situation has become worse than ever with the mining of deeper coal seams at higher production rates in a more complex underground mining environment, in order to meet the huge national demand for coal-fuelled power plants. In the year 2007 alone, more than 30 outburst accidents occurred in underground coal mines with a death toll of 258, and in the year 2008, as of May 22, nine outbursts have already occurred in Henan, Hubei and Chongqing, killing 68 workers. At the same time, China also experienced new trends of coal and gas outburst accidents since its coal production boom in the year 2001. These trends are of great importance for government agencies, coal mine owners and operators to take initiative and effective measures to prevent and control the occurrence of coal and gas outbursts in China?s widely spread outburst prone mining areas. This paper presents outburst data of China coal mines since 2001 and describes new trends of outburst occurrence in recent years, which include outbursts coupled with shocks or rock bursts of competent roof, outbursts in mines under development, outbursts in new mines and mines that have never suffered outbursts before, outbursts in mines that are believed to be of low gas content as well as outbursts in more long-wall faces. Based on the observation of outburst occurrence in China in the period from 2001 to 2008 as well as mining and geological conditions, detailed analysis of the possible causes that led to those new trends of outburst accidents is conducted. The analysis helps shed light on possible future remedies and the necessary measures to alleviate or eliminate outburst accidents in underground coal mines. Suggestions are put forward on future studies that could be of interest to national and provincial government agencies regarding strategic policies, proper technical management practice, identification of outburst prone coal seams, online monitoring of impending outbursts as well as prevention and control measures.

Jan 1, 2008

By P. Gaskell

The paper examines the development of rock movement between a longwall extraction horizon and the surface for a fully caved mining situation. Physical modelling has been used to examine the mechanics of ground movement and the propagation of fractures around the longwall working. The paper discusses dimensional analysis, model construction and measurement technique and data processing of the results into effective graphical forms for further study.

Jan 1, 1988

By Daniel W. H. Su

The importance of incorporating fundamental principles of rock material response and failure mechanics into a pillar strength design model has been demonstrated. To accurately assess pillar strength, a model should account not only for the characteristics of the coal, but also for those of the surrounding strata. The interactions between the pillar and the surrounding roof and floor dictate ultimate pillar strength. Confinement, or the lack thereof, provided by roof and floor frictional end-constraint is one of the most significant factors in the strength of very wide pillars. The best conditions for end-constraint occur with ideally strong roof and floor. In this paper, it will be shown that weak roof and floor may decrease the ultimate pillar strength by as much as 30% compared to ideal conditions. Field observations confirm this pillar strength reduction in the presence of weak roof and floor. Furthermore, rock partings within the coal have a variable effect on pillar strength, depending on the parting strength. A competent shale parting within the coal reduces the effective pillar height, thus increasing the ultimate pillar strength; a weak claystone parting slightly decreases the strength. Imposed load distribution also has a significant effect on pillar strength, such that asymmetric pillar loading, similar to that observed in pillars adjacent to high extraction mining, reduces the ultimate pillar strength below that of equivalent pillars subject to uniform load distributions.

Jan 1, 1997

By John H. Perry

Strata III is a full-spectrum roof control system which provides the mine operator the ability to upgrade his roof control in place. The procedure is easily adaptable with current roof bolting techniques. To use the system, the operator starts by installing a special hollow core mechanically anchored roof belt during the roof bolting cycle. This bolt can be upgraded to a fully grouted tensioned rebar bolt by injecting StrataGee G-300, a special polyurethane grout, around the bolt through an injection port in the roof plate. This same bolt can then be used to inject RokLok binders for roof consolidation by pumping the binders through the core of the bolt. This concept in roof control was developed to provide the mine operator a flexible way to maintain roof control in areas which deteriorate over time, or must be kept open for long periods of time. Possible locations of use would be: longwall set-up rooms, recovery rooms, headgates, intersections, and belt entries.

Jan 1, 1987

By Jon Bowler

Daw Mill Colliery, UK Coal, near Coventry in England, mines the Warwickshire Thick Seam at 800 m/2500 ft depth using longwall retreat with gateroads supported by rockbolts. Over the last eight years the mine has worked longer and wider panels with extraction heights of over 5 m. Recently the mine has experienced high deformation conditions principally from the rib sides resulting in operational issues and production delays. Investigation of rib deformation was undertaken using new inspection and measurement techniques, including systematic laser surveying, and improved rib support consumables were developed and introduced. A new rib trussing system using textile webbing has proved very successful.. A rib support management system was also developed and introduced for face retreat. This allowed rib support to be more effectively managed both for production and safety. For the current developments, new 28-mm-diameter roof and rib bolt systems have been introduced and rib bolt length has been increased to 3 m, with the aim of achieving gateroad stability over the life of the panel. Significant reductions in roof and rib deformation have been confirmed by the latest monitoring results. These ground control innovations are allowing Daw Mill?s potential to be realised. Production from 302?s face in 2008 set new UK and European records. However the support enhancement process continues and further innovations are planned.

Jan 1, 2009