Search Documents

By Frank E. McCall, John K. Marshal, Fred Garcia

Since the advent of longwall mining systems in the United States, mine operators are increasingly relying on methane drainage techniques to supplement the ventilation system. The most commonly used technique is the vertical gob borehole. The number and spacing of vertical gob boreholes per panel is generally based on experience and underground conditions. To design a more efficient methane drainage systems, mine operators must accurately determine methane gas produced. Thus, mine operators must monitor gas flow and methane gas concentration on every vertical gob borehole on active panels at least once or twice during each 8-hr shift. As the mine grows, it is possible to have more than one operating longwall and many vertical gob boreholes. Thus, daily visits to each vertical gob borehole site can become very time consuming. During weekends when methane gas concentrations typically drop because there is no mining activity, borehole sites may not be visited. To obtain accurate gas flow data, a gob borehole monitoring system was designed and constructed by the U.S. Bureau of Mines (USBM). Gas flow, methane gas concentration, gas temperature, barometric pressure, and vacuum pressure of the exhaust fan are the parameters collected by the system. The system also includes circuitry for automatic shutdown of the exhaust fan and an alarm system before an unsafe condition is created. Telemetry components were also integrated into the system to allow for transmission of borehole data to the mine office. As a test, the system was installed and operated on a vertical gob borehole for six months. Test results indicated that intermittent measurements with hand-held instruments from vertical gob boreholes were always higher than gas flows measurements made by the gob gas analyzer system. This paper describes the system components, operational characteristics, and the results of the test program.

Jan 1, 1995

By J. Slivnik, A. Stergarsek

[The site] [Z]irovski vrh uranium ore deposit is located in the extreme north-western part of Yugoslavia, some fourthy kilometers from the capital of Socialist Republic of Slovenia, Ljubljana, not far from the Italian and Austrian border. The sandstone type deposit of uranium ore with medium grade is located in a foothill of Julian Alps. The site shows some typical conditions for this region, which demand special attention in respect to the incorporation of an uranium treatment facility into environment. Among these specific conditions the following site characteristics should be mentioned: - populated area of agricultural and recreational value, - unconvenient climatic conditions with excessive rainfall and long lasting temperature inversions in the winter time, - very pure surface and underground waters which supply the drinking water reservate for large area including the capital of Slovenia, - sharp relief, - unconvenient geological structure. The choise of technology The intention to produce uranium and at the same time respecting the natural characteristics and existing uses of the site made the design of the ore treatment facility relatively difficult one. In general, there were two basic alternatives available perform the task. First alternative was to adopt the usual technological flowsheet with wet tailings disposal and with discharge of used water i.e. liquid effluents into the river. In order to prevent the negative impact of such technology on the sourrounding area sophisticated water purification installation and costly measures in wet tailings disposal e.g. impermeabilisation of large areas by concrete injections, large dam constructions, uncertain capturing of the water sources should be employed. Second alternative was to modify the usual flowsheet by employing the maximal recycling of liquid effluents to the process and to dispose the solid

Jan 1, 1980

By Eugene E. Hively

The Tower Kill is a vertical "stirred" ball/pebble mill recently introduced in the Western Hemisphere. This device offers a significant power savings on wet fine grinding applications when compared to conventional tumbling mills. This paper describes the laboratory application of this mill wet grinding hydrated alumina to products of 50 percent passing 2 to 6 microns.

Jan 1, 1983

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

1.1 INTRODUCTION When underground mining involves total extraction, it induces overburden strata movements. If not properly planned it causes surface subsidence and affects surface environmental conditions. Total extraction usually refers to longwall mining and room and pillar mining with pillar extraction. Surface subsidence has long been a subject of intensive research for scientists all over the world and considerable achievements have been obtained. However due to its difficulties and complicated nature, research into overburden movement has been thus far incomplete as compared to that into surface subsidence. Since surface subsidence is a manifestation of the results of overburden movement, the processes and mechanisms of overburden movement must be fully understood in order to establish the mathematical prediction models of surface subsidence. In this chapter the processes of overburden movement and its zones of movement in the overburden will be discussed. 1.2 PROCESSES OF OVERBURDEN MOVEMENT When total extraction is used, it produces a large void in the coal seam and disturbs the equilibrium conditions of the surrounding rock strata. The roof strata bend downward while the floor heaves. When the excavated area (or gob) expands to a sufficient size, the roof strata will cave. As a result, the overlying strata continue to bend and break until the piles of the fallen rock fragments are sufficiently high to support the overhanging strata. At this tie the overhanging strata no longer cave, but bend and rest on the underlying strata. Strata bending and subsidence develop upward until reaching the surface and forming a subsidence basin. The whole overburden strata and the surface subsidence basin will further go through a period of compaction and gradually become stabilized. Current knowledge regarding the process of overburden movement has been derived from several sources. One is the direct observation of the mined sections and their surfaces, another from field monitoring of strata movements in the overburden, and others from computer modeling and scale modeling in the laboratory. For example, Figs. 1.1 and 1.2 show the results of a borehole monitoring experiment (Borehole B-2) using the full profile borehole inclinometer and full profile borehole extensometer for lateral displacements and vertical subsidence, respectively (Conroy and Gyarmaty, 1983). The panel, 400 ft wide by 5000 ft long and 630 ft deep, was extracted from the Pittsburgh No. 8 seam which had an average thickness of 54 in. The face advanced from east to west. Curve A in Fig. 1.1 shows the inclination of the borehole when it was 45 ft ahead of the face at Position A (i.e., on the solid coal side). The total deviation of the borehole was 1/7000. The first shear movement occurred at 130 ft above the coal seam and appeared to have occurred along the bedding plane with large contrast of rock strata on both sides, i.e., sandstone vs. shale. When the face had passed the borehole 79 ft at Position B, the borehole deformed to assume a bow shape with a maximum deviation of 2.8 in. from the center line. Numerous shearing planes occurred and extended further upward. When the face had passed the borehole by 75 ft at position C, strata subsidence was measured. Fig. 1.2 shows that a strata separation as large as 4 ft occurred at 40 to 100 ft above the coal seam. Above this level, the strata subsided more uniformly with bedding separations within 1 to 2 in. Another example is the longwall mining with complete caving in the Soviet Union's Karaganda Coalfield (Kolebaeva, 1968). The coal seam was 6 ft thick and 154 ft deep. The immediate roof was the fine-grained sandstone interbedded with coarse-grained sandstone. Above this, there was sandy shale and shale. In order to monitor the process of overburden movement, 15 stations were established in a borehole (Fig. 1.3). The elevations of those stations were measured when the face was at various distances from the borehole. Fig. 1.3 shows the movement history of each station. For convenience of comparison, the movement history of each station was plotted on a common reference point as shown in Fig. 1.4. Clearly, the movements of strata from Station # 1 to #6 were nearly simultaneous, i.e., they behaved as a single unit. The strata from Station #7 to # 15 had differential separations, the maximum of which was 40 in. As the face passed by and moved away, strata separations in general reduced gradually. But strata separation between Stations #12 and #13 remained the same until the end of the monitoring period. The total bed separation between Station #7 and # 15 reached 11 in., approximately 18% of seam thickness, when the face was 132 ft beyond. Based on the above observations, the author developed a conceptual model of overburden movement due to underground longwall mining (Fig. 1.5). The above-mentioned two case studies illustrated that subsidence in the overburden strata propagates upward and subsidence velocity decreases from the bottom to the top. When the subsidence velocity at the surface reaches the maximum value, the subsidence velocity at the bottom portion of the overburden strata has decreased considerably and the strata have begun to compact. Bed separation occurs within a certain distance above the coal seam and reduces from the bottom to the top. When the face has moved away, bed separation reduces gradually, so that eventually some beds completely close and others partially close. Bed separation reaches the highest level when the subsidence velocity at the surface is at its maximum value. For instance in Fig. 1.4 surface subsidence velocity was maximum when the face was 38 to 44 ft past the point. At this time the total bed separation was maximum. Overall the strata directly above the opening are subjected to tension in the vertical direction. But above a certain level, all strata move nearly simultaneously. There is also significant shear movement along some bedding planes. 1.3 ZONES OF MOVEMENT INTHEOVERBURDEN After the extraction of a longwall panel or room and pillar section of sufficient width the strata in the overburden are subjected to various degrees of movement from the bottom to the top. According to the movement characteristics, the damaged overburden can be divided into four zones (Fig. 1.6). Caved Zone. After the extraction of coal, the immediate roof caves irregularly and fills up the void. The strata in this zone not only lose their continuity completely, they also lose their stratified

Jan 1, 1992

By Jerry R. Johanson

Introduction Many solids processes that look feasible on paper or even in pilot studies become disasters in full scale. Changes in solids flow characteristics from pilot scale to full scale be- cause of larger solids contact pressures, thermal shocks, or unforeseen temperature excursions often cause full-scale solids flow problems not encountered in the laboratory or pilot studies. Fortunately, proper applications of solids flow principals and solids flow properties measurement at full scale conditions can anticipate the problems and thus provide an accurate basis for full-scale design or existing plant modifications. Solids flow properties The basic solids flow property definitions are given in Table 1 (Johanson, 1966, 1976, 1978, 1985). In this section, the author will discuss each property and its potential for creating full-scale pilot plants. Unconfined yield strength The unconfined yield strength of a bulk solid determines the tendency for cohesive hangups of the solids in the process and is effected by the time at rest, chemical reactions, temperature, liquid content, solids size consist, and phase changes of solids or fluids involved in the process. One of the common mistakes is to consider the solids condition only at the beginning and the end of the process. For example, consider the direct reduction of iron ore. The feed solids are free-flowing, hard lump ore or pellets. The end result is a hard, free-flowing reduced sponge iron lump or pellet. One might conclude that the process involves free-flowing lumps. This conclusion may seem reasonable based on laboratory studies oreven pilot plant studies where solids contact pressures are very low. Unfortunately, during the reduction reactions at high temperatures, the rock or pellets soften and, with solids contact pressures associated with the full-scale plant, may fuse together, thus providing a possible solids hangup in the moving bed reactor not evident in the low pressure pilot scale. Fig. 1 shows some typical unconfined yield strength measurements for pellets as a function of solids contact pressure at various times at rest. Note at low consolidation pressures, generally associated with laboratory or pilot plant studies, the pellets show no strength unless held at rest for an extended time. This will produce a very free-flowing condition in pilot plants that will not exist in the full size reactor.

Jan 1, 1990

By J. Engesser

A research project supported by the Minnesota Department of Natural Resources and the Iron Ore Cooperative Research Committee was undertaken to reduce the dissolution of fluoride into process water during taconite processing. Leach tests were conducted using rod mill feed samples and water containing varying concentrations of calcium and sodium. Laboratory liberation grinds were performed to evaluate fluoride rejection during grinding and magnetic separation. Tube furnace tests were conducted to evaluate fluoride volatilization during pellet induration. The results indicate that fluoride concentration of process water is a function of both calcium and sodium concentration in process water. It appears that less than 1 percent of the fluoride present in rod mill feed will dissolve in process water during grinding. More than 90 percent of the fluoride present in rod mill feed is rejected with tailings during size reduction and magnetic separation. The furnace tests demonstrate that bentonite and fluxstone (calcite and dolomite) addition to taconite concentrate during pellet production increases the amount of fluoride that volatilizes during induration. Lime hydrate addition to pellets decreases the amount of fluoride that volatilizes during pellet induration. During acid pellet production approximately three times more fluoride enters the water during induration-off-gas scrubbing than during grinding. When fluxed pellets are produced three to eight times more fluoride enters the water during off-gas scrubbing than during taconite grinding.

Jan 1, 2004

By Patrick R. Taylor

This paper presents a fundamental study of the thermodynamic and kinetic effects of copper and iron on gold-cyanide leaching. It quantifies the solubilities of the impurities, complex formation, and kinetic effects. The necessity of solution recycle, to meet environmental standards, requires that fundamental information be generated to characterize behavior and allow the identification of treatment methods. Mathematical descriptions of both solubilities and kinetics will be presented

Jan 1, 1983

Simulation models were developed at the Julius kruttschnitt Mineral Research Centre to provide accurate estimates of power consumption for a wide range of equipment. With the models, a range of circuits and operating conditions can be compared by simulation for a particular ore type. Accurate models of classification allow for the interaction between classifier efficiency and target product size (e.g., P80 or percent passing 150 /an) to be considered. This paper considers a range of circuit types and overall energy efficiency in the context of case studies where different circuit types were treating similar ore types.

Jan 1, 1999

By Tom Plouf, Deepak Malhotra

INTRODUCTION The U. S. mining industry experienced a severe recession in the early 1980's. This resulted in the realization that the domestic mining industry had to compete on a global basis and only the strong or the low-cost producers would survive. The economic viability of a mining company not only depended on maximizing mineral recovery but also on its ability to do so at minimum cost. Companies had to become more productive not only by cutting costs, but also by developing and/or evaluating new technologies in existing or new plants. Several innovative concepts, including in-pit crushing and conveying, fine crushing, improved classification equipment, flotation, column flotation, pressure filtration, etc., have been developed in recent years. This paper addresses the impact of new flotation concepts and equipment on mill design. MILL DESIGN PHILOSOPHY Modern mill design, especially for large capacity plants, has its foundation in minimizing capital and operating costs. Capital costs can be minimized by minimizing the various components of the capital cost: infrastructure, equipment, instrumentation, structural, initial spare parts costs, etc. All these costs are minimized by simplifying the mill design and/or process flowsheet. The simplified process flowsheet, where applicable, consists of a single stage primary crusher followed by a semiautogeneous - ball mill grinding circuit to produce feed for a flotation circuit. Multiple flotation circuits have been eliminated in most cases. These concepts minimize the cost and encourage the use of large capacity equipment while maintaining optimum metallurgical recovery. The philosophy of mill modernization/modification is generally driven by the desire to increase the mill capacity within the limits of the existing mill building. This need is facilitated by using large size flotation equipment and eliminating multiple parallel flotation circuits in order to minimize capital and operating costs. Conventional flotation machine development has paralleled this mill design philosophy. FLOTATION CELL DESIGN Since froth flotation has been the most widely used separation process for over half a century, one would expect that it would be possible to design and select flotation machines for specific applications based on scientific principles. But this has not been the case. Best judgment, experience and personal prejudice have played a key role in equipment selection. These factors, along with the difficulty of evaluating new concepts in commercial plants, has slowed progress in implementation and commercialization of innovative ideas and/or equipment. Conventional Flotation There have been no major technological advances in conventional flotation cell design in recent years. A recent flotation cell survey indicates that 'larger flotation cells are still the order of the day.”(1) A comprehensive review of design of flotation machines indicate that they have been mechanically redesigned and are generally simpler and easier to maintain and less expensive to manufacture. (2,3) The approximate chronological development of conventional cells from the 25 cubic foot cells to the 3000 cubic foot cells, which were recently installed at the Copperton concentrator of Utah Copper, is given in Table 1. Larger flotation cells are the obvious choice for new plants or plants looking for expansion because of the following reasons: • They have lower capital cost per unit volume • Installation costs are generally lower because fewer units require less space • Maintenance costs are lower because of fewer mechanisms • Power requirements (HP/ton dry feed) are generally lower • with increased flotation cell size as illustrated in Table 2 [Table 1. Conventional Flotation Cell Size Development Year Individual Cubic Cell Size, Feet 1925 25 1935 50 1960 100 1965 300 1970 500 1975 1,000 1980 1,500 1985 3,000]

Jan 1, 1989

By W. F. McDermott

The Iron Ore Industry has perhaps seen more varied and drastic changes in its approach to crushing and grinding in the last 5 years than any of the other mineral industries, Multimillion ton per year plants have become common place. Centralized control and computers have become an established benefit. Autogenous grinding along with a variety of rod and ball grinding flowsheets are in use. This morning I will discuss a few of the more important and new concepts in the control of these crushing and grinding circuits.

Jan 1, 1970

By Ross W. Smith, D. L. Taylor, K. A. Altman

Traditional sensitivity analysis of metallurgical data has the potential to overestimate the value of mining projects. Such analyses provide no information about the probability of the results. Simulations that rely on the input of statistical information provide more realistic predictions of the value of future projects and offer additional information regarding the probability of the outcome.

Jan 1, 2003

By Y. Wang, G. Xu, N. A. Amoah, A. Kumar

Mining-induced coal dust causes various respiratory diseases to mine workers, such as coal workers’ pneumoconiosis (CWP). Current available underground monitors are expensive, heavy and only measure mass concentration. These disadvantages limit them for regulatory sample monitoring purposes only while personal exposure levels for most miners remain unknown, risking miners to potential overexposures. Low-cost light scattering PM sensors offer a potential solution to this problem with capability of high spatio-temporal resolution PM characterization. However, these sensors require careful calibration before they can be applied in mining environments. There is basically no comprehensive study in the literature using a standard protocol assessing these sensors for coal dust monitoring. With the aim of calibrating the PMS5003 sensors for coal dust monitoring, we design the calibration method and system to calibrate these low-cost PM sensors coal dust monitoring. Working principles of present coal dust monitor and low-cost sensors are presented in detail. The linear regression calibration model which is used for the sensor calibration is further described. Sensor calibration and evaluation protocols are comprehensively compared and discussed. This investigation reveals the feasibility of low-cost sensors for real-time personal coal dust monitoring in underground coal mines.

Mar 2, 2022

By Jerome P. Downey

Treatment of tungsten ore at Anschutz Mining Company's Chicote Grande (Bolivia) operation results in a relatively high grade arsenopyrite byproduct stream. Laboratory and miniplant testwork have been performed at Colorado School of Mines Research Institute to examine the technical feasibility of recovering a marketable arsenic product fr an this source. Process selection was constrained by the remote location of the millsite, which demands an uncomplicated, low maintenance operation. As a result of the research effort, a two-stage roasting/condensing process was developed, featuring the use of an indirect heating method. Arsenic was efficiently extracted and the arsenic trioxide (As203) product consistently exceeded the industrial purity specification of 99.5%. Key process parameters have been secured for extrapolation of the process to pilot or small commercial scale.

Jan 1, 1985

By Samir Kumar Das

Presently Geographic Information System (GIs) is gaining wider acceptance id appreciation in various resource management surveys, generation of various thematic maps, various scientific investigations, environment assessment, disaster management, etc in India but they are general in nature. A huge number of Global Positioning System (GPS) based "Total Station" are playing good roles in India for accurate and quick surveying . The GPS based real time Mine Management and Truck Dispatching System for optimization of productivity is being installed in the Panchpatmali opencast bauxite mines of India. This paper dealt in depth on GIs and GPS and their present roles in the Indian mining scenario.

Jan 1, 2002

By R. T. Swinderman

This paper discusses a series of tests designed to help answer the age old question: ?How much does the belt cleaner wear my belt?? The experimental set up and test method are described. The main variables are: belt cleaner blade materials, cleaning pressures, cleaning angles, belt speeds, and belt top cover grade. The bulk material used is a standard test-grade silica sand. The measured results include: blade mass loss, belt mass loss, and cleaning efficiency.

Jan 1, 2010

By A. Raviprasad, B. Das

Copper ore from the Rakha Copper Concentrator (India) was successfully floated using LIX-65 NS as the collector. The beneficial role of this reagent was clearly demonstrated in hatch-flotation tests. From a feed containing around 1% Cu, it was possible in a single-stage flotation to obtain a 23.7% Cu concentrate with a recovery of more than 90%. The plant now uses rougher, scavenger and a two-stage cleaning process. The tests demonstrated that LIX-65 NS is superior to conventional xanthate for the recovery of copper from the Rakha ore.

Jan 1, 1997

By Martial P. Corriveau

The preparation of coal is essentially the same for export as it is for the domestic market. The big difference, I would say, is that, while coal for certain domestic uses (utilities, for instance) need not always be of the highest quality, as long as it is uniform, the buyer of coal for export invariably demands a well-prepared, top-quality product. And he is willing to pay for it, as long as he knows what he is buying. This is where quality control enters the picture. The day is long past since the export market was the dumping ground for coals which could not be sold on the domestic market. Today, the export buyer wants American coals not so much for a price but for the necessity of blending the American coals with foreign coals to achieve the desired chemical and/or physical characteristics, To blend intelligently, he must know in detail what are the qualities of the coals to be blended. Sampling and chemical analysis facilities at the piers provide the information on the coals exported, These facilities are maintained for the export buyer by independent laboratories; however, in one instance, the buyer operates his own laboratory. With very few exceptions, and Clinchfield?s Moss No. 3 mid-volatile coal is one, cargoes shipped overseas are loaded as blends of two or more coals. Up to now, foreign requirements have not been too clearly defined; therefore, shippers must be prepared to blend mixtures of the desired combination. Successful blending requires an accurate knowledge of the coals shipped. And this makes it necessary for the coal producer to maintain his own control laboratory.

Jan 1, 1959

By Ralph P. Hackl

The Congress gold property, located near Goldbridge, B.C., is extremely refractory with most of the gold disseminated in fine- grained arsenopyrite. Metallurgical testwork conducted by Giant Bay Biotech Inc. indicated that biooxidation pretreatment was capable of increasing cyanide gold recovery from the ore to greater than 90%. To determine if the bioleach process could be successfully scaled up, a 225 cubic meter commercial size bioleach reactor was built and tested at the mine site in 1989. At that time the tank was the largest bioleach reactor ever operated. This paper discusses our experiences in operating the tank, summarizes some of the data obtained and describes the problems encountered.

Jan 1, 1990

By K. G. Sutterer, P. T. Wang, R. Sweigard

One possible alternative for the disposal of flue gas desulfurization (FGD) by-products is to use it as backfilling support material in highwall mine adits. The finite element method was used to analyze the variation in stresses and displacements within and around a highwall adit backfilled with FGD materials. The engineering properties of the rock material and the optimum mix of the FGD materials were obtained from laboratory tests. Finite element analyses show that, for the case in question, the roof displacement would decrease about 48% and the peak stress could be decreased by about 58%. The study indicates that fairly weak FGD materials can eventually lead to the stability of backfilled highwall adits.

Jan 1, 1998

By Adolf U. Honkala

Dundee Cement Company was incorporated in 1958. The equity capital for the venture was supplied by a Swiss firm called Holderbank Financier and a group of its principals. Holderbank Financier, a holding company, is a direct outgrowth of Holderbank Cement Company, a company founded in 1912 by the father of Dr Hans Gygi who is the president of Dundee Cement Company and a member of the Board of Holderbank Financier. From one plant in 1912 located in Zurich, Switzerland, Holderbank grew to its present size of 32 plants in 17 countries, having a capacity of 90 million barrels of cement per year. Dundee Cement Company constructed its first cement plant near the little town of Dundee, Michigan. This site was selected because there is an abundance of limestone and clay of the correct chemical composition for cement manufacture and the deposit was advantageously located near the large population centers of Detroit, Toledo, Cleveland, and Chicago. Construction of the 5. 5 million barrel, two kiln, plant was completed and the plant started up in the fall of 1959. After a year or two of the usual problems in a new plant and the expected difficulty of breaking into a nearly saturated market, Dundee began to prosper.

Jan 1, 1970