Search Documents

By C. A. Rowland

Comminution efficiency can be expressed in three different ways. Theoretical Efficiency: actual energy consumed, in a comminution machine compared to the theoretical energy required to make the size reduction. Operating Efficiency: compares the operating work index, calculated from production comminution machinery operating data, to the Bond Work Index from bench scale comminution tests or calculated from pilot plant operating data. Economic Efficiency: income compared to planned income. Using the Bond Work Index and operating work index, this paper explains how to determine operating efficiency.

Jan 1, 1998

By J. P. A. Hortley

In conventional electrolytic copper production, looped copper starter sheets, on which the copper is deposited, are supported by hard-drawn copper bars. These bars have cross-sectional areas of between 1 and 1.4 in2. The suspension bars serve two purposes: firstly to support the cathode, which can weigh up to 150 kg, and secondly to introduce the electric current. IYI examined these two requirements in detail to see whether a better design could be achieved. Considering firstly the current carrying requirement, it wee noted that under normal refinery conditions, each cathode carries between 400 and soak. If one applies the generally accepted rule that 1 in of copper can carry 1000A4 a suspension bar need theoretically contain only 1/2 in2 of copper. This contention is supported by the fact that the 500A current passed through the cathode also appears to pass quite satisfactorily through the two support loops, which have a cross-sectional area of approximately 0.35 in 2. Turning now to the strength requirements, the cross-section of hard-drawn copper bar required to support a 150 kg cathode is relatively small, and easily met by the present designs. It is not, however, the static load applied by the 150 kg cathode immersed in the electrolyte which causes the damage to the hard-drawn copper, or even the increased static load of a 100 kg man standing on one foot in the centre of the bar; the damage is actually caused by the dynamic loads applied to the bare when they are dropped, thrown into containers, lowered too rapidly into the cell, or otherwise mistreated. The important requirement is therefore that the bar does not permanently bend. Its proof stress of limit of proportionality, rather than the amount that it deflects under static loading, should be the strength criterion. With the hard-drawn copper normally used for the manufacture of suspension bars, it has been observed that the copper becomes annealed during use, particularly at the end of the bar where the current is introduced. Thus, after a relatively short time, the cathodes are in effect being supported by annealed copper bars.

Jan 1, 1978

By Gordon R. Luster

Mineral-processing plants commonly rely on homogenization and proportioning facilities to reduce the variability of incoming raw materials and to blend different materials together to satisfy quality specifications. To determine appropriate designs for these facilities, plant designers need information about the variability of the mined materials, measured as the materials enter the plant. But if the materials to be mined in the future differ greatly from those used in the past, only information extracted from exploratory drilling of the materials in the around may be available. Fortunately, useful information for plant design may still be obtained by combining simulated mineral deposits with simulations of likely mining procedures. The output of a mining simulation is a time series of simulated raw-material characteristics that should mimic the behavior of the real materials to be delivered to the plant in the future. This paper shows how conditional simulations of coregionalized ore grades can furnish information useful in the design of homogenization and proportioning systems.

Jan 1, 1986

By G. J. Lindenburg

The Velvet mine is located in the Big Indian district of the Colorado Plateau. The general area, also known as the Lisbon Valley district, is about 65 kilometers southeast of Moab, Utah and about 120 Kilometers southwest of Grand Junction, Colorado. As shown by the slide, the Velvet area is typical of the high desert of the southwest United States. The elevation at the decline collar is 1,967 meters above sea level. To date, the Velvet has produced 1.5 million kilograms of U308 and 2.1 million kilograms of V205. The current production averages over 4,000 metric tons of ore per month. Access to the Velvet mine is by a 1,160 meter long decline. Fresh air is supplied through the decline and a 152 centimeter cased borehole. Contaminated air is removed by two 152 centimeter cased boreholes. The east side of the mine is mined using a conventional room and pillar method; whereas the west side is mined as combination conventional and random room and pillar,

Jan 1, 1983

By Ross W. Smith, Xiapeng Zheng, Peggy J. Arps

The adhesion (and de-adhesion) of Bacillus subtilis to dolomite was determined under a number of conditions of initial concentration of the organism, agitation, mineral particle size and temperature. Rate equations curves for both adhesion and de-adhesion were constructed, with the rates of de-adhesion being about half that of adhesion. From the temperature data the energy of adhesion was determined to be about 1.02 kcal/mol. Adhesion of dolomite to B. subtilis follows a Langmuir isotherm. Equilibrium constants, adhesion capacity and Gibbs free energy of adhesion of B. subtilis to dolomite (at pH 6.6) were determined. These values were compared to similar data for adhesion of B. subtilis to apatite and dolomite.

Jan 1, 2002

By R. Larry Grayson

A survey of 1250 surface and underground coal mines across the United States was made according to a stratified sampling technique based on national coal districts. A total of 171 responses (13.7% response rate) have been returned and summarized, giving a picture of computer usage in the coal industry. Overall, 63.5% of the respondents use computers, but the percent varied from 100% for large mines to only 44.1% for small mines. As expected, a proliferation of microcomputers has pervaded the industry. Importantly, in spite of the high usage of computers in the industry, sophisticated engineering applications have not yet burgeoned.

Jan 1, 1989

By Martin L. Smith, John M. Kemeny

In blasting, an optimal muckpile size distribution can be found in terms of mining and milling productivity and cost. Fragmentation control requires a means of modeling and evaluating blast results. A principle problem in the practical application of empirical blast fragmentation modeling is the evaluation of the muckpile's size distribution. Image analysis of video and photographic records of production size blasts at Cyprus's Miami and Thompson Creek mines is being used to provide data for estimating parameters relating fragmentation to blast design, energy factor and rock quality. The application of image analysis to the estimation of particle size distribution is reviewed with regards to the problem of fragmentation modeling.

Jan 1, 1993

By D. Royston

Curved pulp lifters can provide improved discharge performance from SAG mills, especially for the coarser fraction of rocks in the discharge. They also can provide improved wear life of the pulp lifter, especially the base of the pulp lifter and diversion cone, over comparable straight radial pulp lifters. Current experience with curved pulp lifters and associated grates is covered including design issues and discharge performance for both the slurry and rock components of the discharge.

Jan 1, 2003

By A. McCombs

Previous models describing the aggregation of polymer-coated particles fail to take into account the fact that there are a limited number of sites onto which a polymer segment can adsorb, called "active" sites. Thus, the collision efficiency is a factor not only of the fractional surface coverage, but also of the number of active sites. In this study, a physical model of the flocculation system was devised in which the number of these sites could be varied, in order to study the effect on particle aggregation.

Jan 1, 1988

By Richard B. Berg

California was a major talc-producing State until the late 1980s when production from the deposits in the Death Valley area ceased because of a number of factors which included pressure to discontinue mining in and around Death Valley National Monument, and health concerns affecting markets for tremolitic talc. The states of Montana and Texas now account for slightly more than half of U.S. talc production. Deposits in an area encompassing southern Death Valley and extending east into the Kingston Range were formed by contact metamorphism of carbonate beds in the Precambrian Crystal Spring Formation next to Precambrian diabase sills. These deposits contain ore ranging from high-purity, fine-grained talc to platy, tremolitic talc with high brightness. Deposits of tremolitic talc and talc schist in the Silver Lake District in San Bernardino County resulted from metamorphism of Precambrian carbonate beds intruded by granitic plutons. Northeast in Esmeralda County, Nevada hydrothermal alteration related to Late Jurassic plutons caused talc replacement of Precambrian to Early Cambrian dolomite. A hydrothermal origin is also indicated for talc deposits in the lnyo Range just north of the Death Valley District where bodies of unusually pure talc occur in Paleozoic lime- stone near Jurassic granitic plutons. Talc is now mined from a deposit in the foothills of the Sierra Nevada Range southeast of Sacramento where quartz-mica schist of the Permian Calaveras Formation has been hydrothermally altered to talc. Replacement of magnesite of the Precambrian Allamoore Formation produced talc deposits mined in the Allamoore District of west Texas. This dark-gray talc of low iron content with carbon- aceous material and dolomite is ideally suited for use in ceramics where it makes a white product when fired. Small bodies of platy light-pink to white talc suitable for use as an extender in paint are also mined in this district. In the Llano District of central Texas talc has replaced impure carbonate rocks and serpentinite. All Montana talc production is from deposits in the southwestern part of the State that formed by Precambrian hydrothermal alteration of dolomitic marble. This alteration produced material with high purity that ranges from very fine-grained, massive talc to coarser grained, foliated talc. Markets include pitch control in paper, paint, cosmetics, ceramics, rubber and plastics. In southwestern and northeastern Oregon, talc has replaced serpentinite in the vicinity of Mesozoic plutons. Soapstone for carving is mined from a southwestern Oregon deposit. Deposits of similar origin occur in central and northwestern Washington.

Jan 1, 1995

By S. A. Voltura

The Phelps Dodge Miami smelter has smelted copper concentrate using the ISASMELT technology since 1992. The design throughput rate was 591,000 tonnes/year and after a slow start-up, the production rate has exceeded the design after the seventh year of operation. In 2002, the smelter consumed 719,000 tonnes of copper concentrate and has the potential to hit the permitted rate of 772,000 tonnes/year. Improvements to the smelting vessel and the surrounding support processes have allowed for continuous improvement from start up until now. This presentation will outline the chronological events and the improvements completed to accomplish these improvements

Jan 1, 2004

By Ralph Bernstein

The processing of earth observation sensor data by digital technology is almost two decades old. Only recently, however, has this technology become practical and economical. The reasons for this are interesting to analyze, and they provide some insight into what the future may bring. Some of the earlier activities and their limitations, current systems and their applications, and future technology direction are summarized.

Jan 1, 1979

By J. M. Barker

Formation of commodity agreements depends mainly on the economic instability and associated mitigation measures inherent in the economic conflict between more developed and less developed nations. Five types of possible agreements exist: futures market, buffer stock, restrictive agreement, multilateral contract, and compensatory finance. Lack of market separation between sulfur consumers and producers coupled with large world production and highly concentrated export production in theory suggest a restrictive agreement as most likely. In practice, stockpiling of sulfur, an informal buffer stock, as done in Canada and perhaps the Middle East, has been the main sulfur price-supporting mechanism in the past two decades. No commodity agreements involving sulfur now exist except for multilateral contracts. Sulfur agreements apparently have existed rarely, if at all, in the past. Law (1975) refers to sulfur as one of a group of commodities where "there have been additional control efforts of various types." Clearly, sulfur was a candidate, at least conceptually in the past, for some form of commodity agreement. The following discussion centers on the world sulfur market from 1976 to 1985 in this context.

Jan 1, 1987

By Christoph Wels, Michael Royle, Shannon Shaw

Intrinsic remediation is the effect of natural attenuation mechanisms - dilution, dispersion, sorption/precipitation and biodegradation - reducing contaminant concentrations in ground water to specified levels at predetermined compliance points in the aquifer. Current monitoring and modeling for post closure was used to assess the current and long-term potential of intrinsic remediation of contaminated seepage originating from a large reactive (sulfidic) tailings impoundment near Questa, New Mexico. It is concluded that the natural attenuation mechanisms of precipitation within the tailings (as a result of buffering) and dilution/dispersion within the aquifer are currently active and likely sufficient to reduce contaminant concentrations to below state standards in the long-term. Other natural attenuation mechanisms such as sorption and biodegradation within the receiving aquife4s) were not assessed here, but are likely further reducing contaminant concentrations. Active interception and recovery of the seepage water is being maintained until monitoring demonstrates that intrinsic remediation has successfully achieved the level of water quality control required.

Jan 1, 2000

By D. B. Jenkins, D. R. Taylor

Treatment of bentonite clay with mineral acids yields a modified clay product of high surface area and acidity that exhibits enhanced adsorptive and catalytic properties. A highly specialized segment of the clay industry based on this process has evolved into a worldwide business with a capacity of about 500 kt/a. This paper will present data on the chemistry, mining, manufacturing, and applications for acid-activated clays.

Jan 1, 1988

By S. Chander, A. Briceno

The effect of sample storage in argon and in air on the kinetics of oxidation of pyrite from a coal source was studied using accelerated-weathering tests that were performed in laboratory columns. Prior to the weathering tests, the samples were crushed, ground and stored for various periods of time in either argon or air. The test results showed a dramatic difference in the rate of oxidation of the aged samples. The interpretation of the differences was based on the hypothesis that the aging of pyrite led to the formation of surface coatings that changed with time. "Dry" oxidation produced surface coatings that had properties different from those produced by "wet" oxidation. The significance of these results to pyrite/reagent interactions during flotation and in evaluating the acid-mine-drainage potential of pyritic waste materials is discussed.

Jan 1, 1995

By K. A. Natarajan, M. K. Yelloji Rao

The electrochemistry of sphalerite and chalcopyrite was investigated under both open-circuit and applied potential conditions. Emphasis was placed on the selective dissolution of sphalerite from a mixture of sphalerite-chalcopyrite flotation concentrates as a function of applied potential, acid concentration, pulp density, and time. Morphological studies using a scanning electron microscope (SEM) were also carried out with chemically leached, galvanically leached, and unleached surfaces of sphalerite and chalcopyrite. Selective dissoulution of sphalerite could be achieved if the mixed chalcopyrite-sphalerite concentrate slurry was maintained at a negative applied potential of -0.4V (SCE). Probable mechanisms involved in the selective dissolution of zinc are disscussed.

Jan 1, 1990

By Y. H. Chia, P. Somasundaran

Carrier flotation of anatase from clay using coarse calcite is investigated, together with relevant basic properties of the system including aggregation and zeta potential, under different chemical and hydrodynamic conditions The roles of carrier sue and amount also are considered Mechanisms responsible for selective aggregation and flotation are reviewed

Jan 1, 1983

By William C. Larson

The number of uranium in situ leach operations has increased significantly since 1975. As of May, 1980, there were a total of 27 active projects, including 16 commercial scale operations (or under construction) and 11 pilot scale operations. The south Texas uranium district and Wyoming have been the most prominent areas in early field experiments as well as in commercial application of this new recovery technique, although in situ leach tests are now being conducted in Colorado and New Mexico. The growing number of commercial-scale operations is accepted as prima facie evidence that in situ mining now offers a third option along with open pit and underground mining for winning uranium from sandstone host rocks. It is estimated that in 1979 about 9 percent of the nation's total uranium production was from in situ mining. However in situ mining of uranium is not without its environmental controls. The primary emphasis of environmental controls falls into two catagories; namely, control of the leach solutions during mining and demonstration of ground water restoration. Finally this paper briefly reviews the Bureau of Mines research program in uranium in situ mining.

Jan 1, 1980

By J. D. Miller, J. Hupka

Environmental applications of the air-sparged hydrocyclone (ASH) technology are presented. The original ASH design used porous sintered steel or porous polyethylene tubes as spargers. To diminish/prevent plugging and to reduce pressure head loss in the gas path a wire screen sparger and new hydrocyclone design have been developed, which allows for wide application of the technology to solve environmental problems and to be used as a chemical reactor. Field and laboratory trials have shown that the ASH technology might be preferred for the stripping of volatile organic compounds WOC) from contaminated water. The ASH has also been developed for absorption of SO2, toluene vapors, and for the recovery of cyanide.

Jan 1, 2005