Search Documents

By B. Stewart, R. Li

Coal waste materials inhibit the direct establishment of vegetation due to adverse physical and chemical properties, particularly low water retention and high potential acidity. The Moss #1 coal refuse pile is located in Dickenson County, Virginia, and was idled in the late 1980s with little topsoil resources available for final closure. The refuse was acidic (Total S = 0.38%; pH = 3.6), black in color and high (70%) in coarse fragments. The refuse also had a low water-holding capacity (4.5% in < 2.0-mm fraction). A small plot experiment was established on the refuse pile to evaluate the effects of liming rates (50% and 100% of lime requirements) and topsoil thickness (15, 30 and 60 cm) on vegetative growth and leachate quality. Liming and topsoil amendment increased the surface soil pH from <4.0 to >6.0 over a two-year period, which resulted in greater vegetative cover and biomass than the control plots. All topsoil treatments resulted in greater vegetative cover and biomass than plots treated with lime only. This was due to improved surface soil physical and chemical properties. A topsoil treatment of 60 cm gave the thickest vegetative cover and biomass yield. Such a treatment, however, would be cost-prohibitive at this location. Applica¬tion of 27Mg ha`1 of lime to the refuse surface along with 15 cm of topsoil produced acceptable two-year vegetative cover and biomass, and this appeared to be the optimal treatment for this particular situation. Both liming and topsoil had no affect on leachate pH and the electrical conductivity of leachates collected below the plots. This suggests that surface revegetation will have little effect on the quality of water draining through the pile. Therefore, long-term water-treatment requirements may not be reduced by successfully revegetating the pile surface.

Jan 1, 2000

By K. Kavouridis

Coal is broadly recognized as sure, competitive, diversified, not vulnerable and predictable in price energy resource. In power generation coal is playing a dominant role in the EU-27 with 25% of installed capacity and almost one third of the power generation. The role played by the domestic resources and especially by coal are increasingly becoming the focus of the EU energy strategy. There is a strong pressure for the decarbonization of the energy mix. The Emission Trading system (ETs) can have an impact on the shift to lower carbon-intensity fuels. The impact of ETs on coal can be important, because it is very short sighted and only defines the period up to 2008-2012. The ETs CO2 regime must ensure that investment in coal-fired plants in the long term are supported. EU Research Institutes and Coal Industry identified an important CO2 reduction potential by improving the efficiency of the conversion of solid fuels into electricity. Highly efficient clean coal technologies can contribute to reasonable costs and challenge the issue of climate change. It must be pointed out that the EU Energy policy should now concentrate on the necessity to effectively support demonstration projects and to create the legal framework for the integrated approach of efficiency enhancement and CCS. It is not a right approach to implement CCS before the technology is demonstrated and before it is clear that it will be commercially viable.

Jan 1, 2007

By L. W. Laage

MFIRE is a mine ventilation and fire interaction computer simulation program. It allows transient state ventilation simulation and features mass based flow rates, natural ventilation, air recirculation, fan curve fitting, airflow reversal and product of combustion tracking. MFIRE was designed to accommodate the needs of the mining industry for routine ventilation calculations and mine emergency planning. This paper describes recent work by the Bureau and MTU to improve MFIRE by incorporating humidity in the mass flow and heat exchange calculations, a data file preparation program and variable reference density in the network calculations. Recent bug fixes are also discussed.

Jan 1, 1993

By T. Negeri, A. O. Orumwense

Microwave pretreatment is one of the emerging technologies which have been reported as having potential economic benefits for the processing of amenable ores. The application of microwave pretreatment to the processing of refractory and finely disseminated ores is of great interest as the technology can potentially reduce high comminution costs and improve mineral liberation. Sized ore samples were subjected to microwave irradiation at power levels varying from 1 to 5 kW over exposure times of between 1 and 6minutes in order to determine the influence of heating rate on mineral transformation, ground product size distribution and mineral liberation. The microwave irradiated samples were ground and subsequently floated. A comparison is made with non-microwave treated samples. Flotation grade and recovery show a strong dependence on the microwave absorption characteristics of the mineral components of the ore, in the following decreasing order -sphalerite, galena, and lastly chalcopyrite.

Jan 1, 2003

By R. S. Austin

One-third of the world&apos;s and most US kaolin is produced from Late Cretaceous and Early Tertiary sedimentary strata in Georgia and South Carolina. The kaolin is part of a belt extending to Arkansas of aluminous lateritic deposits, including bauxite. Original sediments were profoundly altered by chemical weathering during Early Tertiary time. Mining exploits those uncommon deposits where extreme leaching and chemical recombination have produced a clay of nearly pure mineral kaolinite. Properly selected and refined, kaolin is an important pigment, filler, extender and chemical compound in the paper, paint, plastics, ceramics and catalyst industries.

Jan 1, 1998

By C. S. Compton, D. R. Dolinar, D. C. Oyler

More than 80% of U.S. roof bolts are fully-grouted, but about 1500 roof falls are reported each year. Anchorage failure of a fully grouted bolt can occur when the roof is active near the top of the hole. This paper reports on an extensive series of short-encapsulation pull tests (in which the bolts are installed with only 1 ft of resin) that were conducted in the National Institute for Occupational Safety and Health(NIOSH) Mine Safety Research Laboratory and operating mines in WV and PA. The tests confirmed that poor anchorage can been countered under some weak rock conditions. Suggestions for improving anchorage are included.

Jan 1, 2003

By V. R. Degner

Given: the process tonnage, performance objectives, and plant floor area, the paper will outline the metallurgical and machine hydrodynamic scale-up procedures for translating the lab flotation test results to the design of a full size flotation machine installation, including the machine number, size, and arrangement. Machine selection considerations for rougher, scavenger and cleaner duty, and special considerations relative to specific applications, will be summarized where appropriate. The value of kinetic modeling in quantitative metallurgical (lab to full size machine) scale-up will be reviewed considering a coal installation, and design information for additional applications such as copper, molybdenum, iron, phosphate, and potash will be discussed.

Jan 1, 1986

By H. Reginald Hardy, Xiaoqing Sun

Rheological models are widely accepted as a means of describing the mechanical behavior of geologic materials. It has been found, however, that rheological models developed for a specific stress level on the basis of linear visco-elasticity generally are not satisfactory at other stress levels. It has been suggested that the parameters of such models should be functions of stress level (Hardy, 1965; Kim, 1971). In this paper, continuous functions of stress have been utilized to obtain the required variation of Burgers model parameters with stress level. The model developed using these functions provides a constitutive relation which reflects the real time-dependent behavior of rock materials. The new model is capable of predicting the creep behavior over a wide range of stress levels and also predicts mechanical behavior under different loading condition (e.g. constant stress rate). It is also interesting to note that the mechanical behavior of individual elements in the model appear to reflect the different stages of brittle fracture in rocks (Bieniawski, 1967), namely; crack closure, elastic deformation, stable fracture propagation and unstable fracture propagation.

Jan 1, 1986

By Donald G. Oss

The need for instrumentation and automatic control of the various parameters in the heavy media process of iron ore beneficiation has been apparent for some time. Continued demands for higher grade, competitive products from the Mesabi Range have made it necessary to increase the efficiency of the process in every possible way. A brief review of a typical heavy media flow scheme, as illustrated in. Figure l, might be in order for those not intimately associated with this process of iron ore beneficiation.

Jan 1, 1962

By C. F. Kaiser

The Broken Hill proprietary company Limited grate kiln pellet plant (1) located at Whyalla in South Australia commenced production on May 13, 1968. During commissioning, about 25,000 long tons of fluxed pellets were produced. Plant performance was satisfactory and acceptable under the plant guarantee. For production reasons, it was necessary to curtail the fluxed pellet run and revert to the production of acid pellets. In 1970, some 250,000 long tons of fluxed pellets were produced under varying operating conditions to determine the requirements for optimum quality pellets at acceptable production rates. In excess of 180,000 long tons of these fluxed pellets were exported to Japan. Problems experienced in production of the fluxed pellets are detailed, and the quality of the fluxed pellets compared to that of normal acid pellets produced at Whyalla. Brief Plant Details Run of mine ore treated was predominantly soft and friable and contained an average of 66 per cent Fe, 1.7 per cent Si02 and 1.8 per cent Al203. The main iron mineral in the ore was hematite with some martite also present. Plant feed was ground dry in ball mills 11 ft in diameter by 29 ft long to a Blaine surface area of 1600 sq.cm/g and the ground ore was wetted in a pug mill. Balling was carried out in balling drums 10 ft in diameter by 32 ft long. Induration equipment included an eighteen windbox grate 12 ft 2 in. wide by 164 ft 1 in. long, a rotary kiln 18 ft 6 in. diameter by 118 ft 8 in. long and an annular cooler 50 ft mean diameter by 7 it wide.

Jan 1, 1972

A number of factors have resulted in the widespread use of computer simulation as a day to day tool in the mineral processing industry, as is the case in most engineering disciplines. A number of simulation packages, both steady-state and dynamic are now available commercially. The developers of such software face an enormous challenge in maintaining and improving the packages due to the complexity inherent in such systems. This problem known as the software crisis faces all developers of complex software. Object-oriented (OOP) and design is a methodology which has been developed to try and minimise this problem. The use of the OOP paradigm in the devlopment of simulation software for mineral processing systems is explored in this paper and it is found that OOP techniques have major benefits for the design and development of such software.

Jan 1, 1992

By Paul Soros

A major share of the increase in the energy demands of Ontario province in the next decade will be supplied by bituminous coal mined in the U,S, To be competitive with alternative sources of energy, it is essential that the delivered cost of coal, inclusive of all transportation charges, be kept at a minimum. The Bessemer aid Lake Erie Railroad Company and the Pittsburgh and Conneaut Dock Company are currently building a shiploading terminal at Conneaut, Ohio, to service this tonnage, together with expected increases in coal consumption in the Eastern Lake Erie - Lake Ontario area, (see Fig, 1).

Jan 1, 1965

By David A. Summers

Historically, the presence of methane has been a problem, mainly in and around the working areas of active coal mines, and only in these area has drainage been considered. Drainage, where practical, has been achieved through the drilling of holes forward into the coal and the surrounding strata from the working area. These holes generally have been short in length, although where methane drain- age operations around a longwall face have been undertaken, the holes have had to be longer in order to adequately drain from the center of the face into the access gate roads. In recent years, attempts have been made to degasify the coal seams in advance of mining, without disruption of the mining cycle. This is done by drilling much longer horizontal holes through the coal in advance of the working area. Under the aegis of the Federal Government, methods have also been developed for draining seams of coal of their methane content in advance of mining, but from shafts sunk from the surface, without using the active area of the mine as the location for the drill holes.

Jan 1, 1979

By Tegner C. Johnson

Just a few years ago my company was referred to as the Marion Steam Shovel Company. We still make shovels, both two and eight crawler types. The eight crawler stripping shovel appears to have been replaced by the walking dragline for overburden removal and in some cases for the mineral as well. The walking dragline appeared in the coal fields in the early 1930&apos;s. It owes its popularity today to the fact that it can cope with overburden depths in excess of 100 feet and with blasted sedimentary rock, all at an 0 & 0 cost of ± 10¢/BCY.

Jan 1, 1974

By C. A. Garcia

The solvent extraction of gold cyanide from alkaline cyanide solutions with monosubstituted guanidines, bis disubstituted guanidines and a tetrasubstituted guanidine was investigated. The guanidine functional group is protonated in alkaline solution and the guanidinium cation is stabilized so that the aurocyanide anion can be extracted even at -pH 12 if an appropriate carrier is used. Typical aprotic carriers including both aliphatic and aromatic solvents limit gold extraction by guanidines to pH 10; whereas the presence of an alcohol extends gold extraction to pH 12. UV spectroscopy suggests that the alcohol facilitates protonation of the guanidines, stabilizes the guanidinium cation, and facilitates gold extraction at high pH.

Jan 1, 1993

Iron ores may be upgraded by flotation of iron oxides or siliceous gangue using either cationic or anionic collectors. The electrostatic mechanism of adsorption can account for the complex chemistry involved. In industrial practice, only cationic silica flotation is used at present in North America. Some of the seemingly paradoxical phenomena of cationic silica flotation behaviors in meeting the demand for low silica concentrates are reviewed.

Jan 1, 1989

By Richard W. Patton

With the advent of the Clean Air Act and the installation of flue gas desulfurization (FGD) equipment (scrubbers) on coal fired power plants, the management of solid wastes has taken on added importance. Aside from the large amounts of fly ash and bottom ash usually generated, large quantities of liquids in the form of scrubber sludge are also produced. These wastes must be disposed of within the constraints of land and water quality regulations. This paper describes the practices adopted by the electric utility industry in denting with this problem, including methods of generation and treatment, quantities and characteristics of the materials, and transportation and disposal practices. The paper also briefly describes final product characteristics and several applications for commercial utilization and land reclamation.

Jan 1, 1983

By Kot F. v. Unrug

In spite of extensive research and accumulated experience from mining operations, appropriate coal strength values for pillar design remain debatable. Coal strengths determined in the laboratory on standardized samples vary widely among various coal seams with poor repeatability. Penetrometric in situ strength testing obtains multiple measurements at multiple horizons within the coal seam to provide a strength profile. Alliance Coal has used that method in many of its mines for pillar design. Pillars in these mines perform well. This paper presents a series of case studies and discussion of issues related to coal pillar design. The analysis demonstrates that the proposed default in situ strength of 900 psi is appropriate when no other data exist. However, in the case of appropriate strength measurements combined with analysis of pillar structural composition, differing values can be used successfully. In areas where the penetrometric derived in situ strength is greater than the standard 900 psi in situ strength, reserve recovery has been optimized as required by law without compromising safety.

Jan 1, 2009

By J. P. Golightly

The nickeliferous laterites of Soroako are described in their setting in the huge Cretaceous ultramafic complexes of central Sulawesi, Indonesia. The ore bodies occur on spurs, ridges and hill flanks beneath remnants of extensive erosional surfaces. Weathering pro- files that have developed on unserpentinized harzburgite and on strongly serpentinized lherzolites show distinctive laterite structures, mineralogy and chemistry. The former are unique to the Soroako area and permit an unusual degree of upgrading by rejection of unserpentinized peridotite boulders. A mass balance calculated for a selection of profiles indicates that in situ leaching of a column of peridotite 20-50 meters thick has taken place with only minor lateral migration of nickel in solution.

Jan 1, 1979

By Ke Yang

In Chinese coal mines, extraction of deep, highly gassy soft coal seams sandwiched between soft floor and soft roof in complicated geology is commonly encountered. How to safely and efficiently excavate such seams is a very significant and important problem. It has been a focused research area in recent years. By combining the characteristics of fully mechanized longwall mining methods such as large cutting height and mining along the dip, an integrated method and technologies for the Zhangji Coal Mine were developed. This technology includes the design of a complicated geological exploration system, optimization of mining method and working face parameters, control of rock pressure and high levels of gas, reliability model of the production system, and selection and compatibility of equipment. Engineering practice shows that the integrated technology was successful in mining these complicated seams. This study not only enriches the mining method, but also improves the coal mining practice, especially ensuring both safety and productivity under complicated geological conditions.

Jan 1, 2009