Search Documents

By J. Y. Hwang

Processing of fine mineral particles in a slurry is a difficult problem. Methods to make fine particles magnetic have been developed recently and may offer a solution to this problem. Particles of nonmagnetic materials can be selectively rendered magnetic through surface interactions with magnetic reagents. When adsorption occurs, the magnetic susceptibility of the material is increased. Magnetic enhancement at several orders of magnitude can be achieved. Selectivity of the adsorption can be controlled by the functional groups of magnetic reagents and various surface interaction mechanisms. This approach allows a new degree of freedom for the processing of fine mineral particles, even with conventional magnetic means. Separation of valuable minerals and filtration of slimes from tailing ponds and recirculated water are examples of the applications. Basic principles of this technology are discussed in this study.

Jan 1, 1992

By D. Kang

The adsorption behavior of silver in ammoniacal solutions on to activated carbon has been studied. The parameters affecting the adsorption of silver on to activated carbon included temperature, agitation speed, concentration of cations and anions as well as that of ammonia. It was found that the adsorption of silver from ammoniacal solutions was dependent upon the initial silver concentration in the solution and other factors. The recovery of silver from ammoniacal solutions was found to be not so effective as the case with gold reported earlier. The adsorption rate was relatively slow overall, despite a rather fast initial adsorption. The apparent activation energy for the adsorption was measured to be 30.2 kJ/mol. It was believed that the kinetics of the silver adsorption on activated carbon was limited by a mixed control mechanism.

Jan 1, 1998

By J. G. Groppo

Hyperbaric filtration was evaluated at the laboratory scale for dewatering fine coal cleaned by froth flotation. A laboratory pressure filtration procedure is described to obtain uniform cake structure from dilute slurries containing a significant amount of coarse material. Baseline tests were conducted varying filter operating parameters such as driving force, time, cake thickness, percent solids, viscosity and pH to determine optimum operating conditions for eventual application on a continuous pilot scale hyperbaric filter.

Jan 1, 1994

By K. Adam

Uncontrolled disposal of pyrite wastes and concentrates comprise a major source of acid drainage in active and abandoned sulphide mines. In this paper, the state?of-the-art mitigation measures implemented for the final reclamation and closure of a pyrite concentrate stockpile at Platia Karra, Stratoni mines, Greece, are presented.

Jan 1, 2002

By William Lodding

Unlike most ore minerals, the raw materials for lightweight-aggregate, such as clays and shales are abundant everywhere. In view of this ample choice, what are the reasons for many plant failures attributed to the raw material? How can we arrive at a proper choice of the raw material, the proper processing method for the chosen material, predict its behaviour in a plant and the properties of the final product? Determine the uniformity of the raw material and possible harmful impurities? One basic choice is sintered versus kiln-fired aggregate. It will be based on market preferences and availability of the raw material. Almost in every case a good raw material for one process is poison for the other.

Jan 1, 1964

By Y. Kurokawa, R. Kurosawa, I. Iwata, I. Fukuoka, N. Sugita

INTRODUCTION The Ningyo-toge Mine is located in the western part of Honshu, about 800 km from Tokyo. Since the discovery of uranium ore deposit at Ningyo-toge in 1955, different kinds of mining and milling tests have been carried out. A new pilot plant of milling and UF6 conversion is also being under construction. Operations are scheduled to start by the end of this year. In 1979, the uranium enrichment pilot plant was constructed at Ningyo-toge and test operations have started. Thus, the Ningyo-toge area is assigned to undertake the Research and Development of the upstream of the nuclear fuel cycle in Japan. PNC has been strengthening its security measures more than ever. This paper will focus on the disposal of wasted material, especially on the disposal of heap leaching residue, in Japan. URANIUM ORE DEPOSITS The uranium of the Ningyo-toge Mine is characterized genetically by epigenetic sedimentary type deposits. They occur in the host rock of Neogene tertiary fluviatile conglomerates and sandstones which unconformably overlies the Mesozoic-Palaeogene granitic basement covered with lucustrine deposits and volcanic ejecta. More than 12 deposits have been found over the area of approximately 160 km2, and distribution of the deposits are strongly controlled by the so-called channel structure, probably remnants of paleo-streams on the denudation surface of the underlying grantic basement. Each ore body has different shape and dimension respectively, but about 2-3 meters thickness with the average grade of 0.05-0.2% U308 is common feature of the ore bodies. The ore is soft and loose, and it is composed of common rock forming minerals of allogenic origin and their altered products. The chemical composition of the ore depends on the constituents of the country rocks or the pebbles. A primary mineral, ningyoite and secondary mineral, autunite are major ore minerals, although three primary tetravalent minerals and thirteen secondary hexavalent minerals have also been detected. MINING EXPERIMENT Since 1959, various types of underground mining tests have been carried out at Ningyo-toge Mine. The room and pillar method was safe and simple, although the uranium ore recovery was below 70%. After experiment of the retreating long-wall method and slicing mining method, it was found that the modified long wall method was the most appropriate for the underground mining of the Ningyo-toge uranium deposits. This method was completed successfully to increase efficiency up to 2 or 3 times, as compared to conventional methods. MILLING EXPERIMENT In 1964, a small test mill was constructed at Ningyo-toge, and a milling experiment using the Ningyo-toge uranium ore was started. Re-modelling of equipments and improvement of the process lead to the establishment of the technique of the so-called wet process, and produce UF4 directly from the ore. The flow diagram is shown in Fig. 1.

Jan 1, 1981

By Sheldon P. Wimpfen

Forecasting, an ancient art, is con-ducted by everyone in varying degrees. It is a vital aspect of mineral production and conditions must be predicted over a long time frame in all aspects of the industry from exploration to plant construction. Although many government agencies as well as private industry make forecasts, there are insufficent "make good" analyses performed. The performance of more such studies could sharpen forecasting ability.

Jan 1, 1983

By Felicia F. Peng

The naturally occurring aged manganese oxide coated on the granular media was found to have a catalytic effect on the removal of low concentration of Mn(II) (-1 ppm) from drinking water. Applying this principle, a manganese removal technique was developed for removal of higher concentration of Mn(II) (-100 ppm) from mine drainage by using various aged filter media and synthesized granular media with manganese oxide coatings. Laboratory-scale continuous granular media column experiments were conducted to assess the feasibility of manganese oxide-coated granular media for Mn(II) removal from synthesized mine drainage. The removals of Mn(II) were evaluated as a function of operation parameters including solution pH, manganese oxide concentration coated on the media, interstitial velocity, and oxidant concentration of influent. Higher solution pH and/or higher manganese oxide concentration promoted the removal of Mn(II) on the oxide-coated granular media under low interstitial velocity. Addition of sodium hypochlorite as an oxidant in the influent resulted in continuously regenerated oxidized surface to serve as the catalyst for Mn(II) oxidation reaction on the surface of oxide-coated media.

Jan 1, 1994

By Keith S. Olsen

Any discussion of barite mining is virtually impossible without considering, almost in the same breath, the many other variables, such as beneficiation, transportation, infrastructure and location that impact the economics of a particular barite orebody. My comments will be limited to just the mining aspects of barite orebodies and these observations must be considered in proper context with all other parameters affecting exploitation of a barite property prior to final decision on economic feasibility. In many instances low-cost mining situations are more than offset by high-cost beneficiation requirements. Likewise, there are cases of relatively high-cost mining associated with no or low-cost beneficiation requirements thus permitting economic exploitation. Barite orebodies and occurrences are almost as varied as the number of occurrences. As in most mining situations, the design of a mine plan and implementation of a proper exploitation program must be approached on a case by case basis. Proper and sufficient geologic control of a barite orebody must precede the development of a mine plan. Generally speaking, barite orebodies can and, at many times, do "strange" things; pinch with depth; almost never increase in size with depth, overturn, fault-off, change grade, etc. Due to the extreme variable nature of most barite orebodies, a mine plan and its implementation must be as flexible as possible. The ability to quickly adapt to variable conditions will greatly enhance the economics within a particular barite mining environment.

Jan 1, 1980

By D. E. Ranta, G. H. Giroux, A. W. Randall, D. A. Barr

Zinc-lead ores of the Pine Point District, Northwest Territories, Canada, are hosted in paleokarst cavities within a Middle Devonian carbonate barrier complex. Of the nearly 100 deposits found, most are irregularly distributed along two main regional stratigraphically controlled trends. The ores, which occur predominantly as open space filling, form deposits most of which average one million tonnes in size with an average grade of 10% combined zinc plus lead. Geological features related to karsting control not only distribution of deposits but also their shape, size and grade. The higher grade ore in these deposits generally occurs in a relatively small core area. Consequently, accuracy of reserve estimation is dependent on drill-hole density and understanding of karst geometry. Several case examples will be reviewed to demonstrate the relationship between shape, size and grade of deposit, geological reserves and drill-hole density, along with a discussion of geological ore reserve estimation methods.

Jan 1, 1992

By Wallace W. Wilson

It scarcely 1s possible to read a new issue of any of the principal mining trade journals without noting some mention of a major new overseas mining venture with which one or more domestic companies are involved. These projects seem to follow a fairly consistant pattern; most are large open pit mines, with relatively low grade ore bodies but huge reserves; the total price tag will be in nine significant figures and around half or more of the total cost will be for infrastructure. West1 noted that nearly $7 billion is being invested annually for new mining projects and the expansion of existing mining ventures, in the free world. He anticipates that by the year 1975 such investments would reach the $10-11 billion annual figure, and that in the five year period 1972-76 total capital requirements can be expected to aggregate around $45 billion. The proportion of this total investment which will be financed in some manner is difficult to estimate because of the variety of available financing arrangements. West estimated that around 75% of the total capital would come from internally generated funds, with the balance from external sources. Conceivably a substantially higher percentage could be attributable to external financing, especially it the trend of recent mineral development in Canada and Australia is any criterion, and of course, including local sales of equity as a part of the package.

Jan 1, 1973

By G. A. Swanquist

INTRODUCTION This article describes the yellow cake drying, packaging and dust collection circuit of the United Nuclear Church Rock Mill. It also describes the layout and floor plan of this section as well as the operation and performance of the various equipment. In order to place the yellow cake section in perspective of the mill as a whole, the mill circuit is described briefly. CHURCH ROCK MILL GENERAL DESCRIPTION The Church Rock Mill contains six operating sections shown in Figure 1 in block diagram form. The grinding section consists of a semi-autogenous mill in closed circuit with a hydrocyclone. The slurry is then routed to the leaching tanks. Sulfuric acid and sodium chlorate is added to dissolve the uranium. The pulp is transferred from the leach tanks to the thickeners where the uranium bearing liquid is separated from the barren solids. The uranium bearing solution is then filtered and pumped to the solvent extraction section. [ ] In the solvent extraction section, the uranium bearing aqueous solution is brought into contact with an organic solution composed of kerosene, amine and isodecanol. The amine extracts the uranium from the aqueous solution. This organic solution is then routed to the stripping section, where the uranium is removed from the organic solution with an ammonium sulfate aqueous solution. The pregnant stripping solution now concentrated to 30 gpl U308 is routed to the precipitation tanks where ammonia is added to precipitate the uranium. The yellow cake is then washed in a counter current circuit of two thickeners and one centrifuge to remove impurities, mainly sulfates in order to meet specifications. The centrifuge centrate is routed to the second wash thickener for forward wash. The centrifuge cake at approximately 50% solids consistency is transferred to the yellow cake dryer via a screw conveyor. YELLOW CAKE DRYING, PACKAGING AND DUST COLLECTION Figure 2 shows the flowsheet of the integrated circuit of drying, packaging and dust collection. This section of course centers around the yellow cake dryer as the main equipment. The other main units are the dust collectors for the dryer and packaging respectively, a yellow cake storage bin and the yellow cake packaging facilities. Physically, all of this equipment occupies four floors, beginning at the top floor: 1. Both dust collector fans, the centrifuge and the screw conveyor to transport the yellow cake to the dryer. 2. The dryer, fire box and both dust collectors occupy the third floor. Figure 3 shows the floor plan of the third and fourth floors. 3. The yellow cake storage bin and dryer dust collector sump are located on the second floor. 4. The ground floor houses the loading facilities consisting of two load out ports from the bin to barrels, a roller conveyor loop, drum weighing scale, and change room facilities. Figure 4 shows the ground floor plan. Figure 5 is an elevation view of this section showing the overall equipment arrangement.

Jan 1, 1981

By Donald P. Schlick

Gentlemen, today I would like to talk to you about metal and nonmetal mine health and safety--past, present and future. Briefly, I will comment on the past because it is important to an understanding of our present activity and our plans for the future. Federal inspection of noncoal mines was not authorized until 1966, when congress passed the federal metal and nonmetal mine health and safety act; public law 89-577, with the passage of this act, the federal inspector, for the first time, had the delegated authority and responsibility to enforce health and safety regulations designed to prevent personal injuries and occupational diseases, the new law also provided for the education and training of our miners; assistance to the operator through the transmission of technical and scientific information and assistance and equally important, the law made provision for state participation in the congressional mandate to prevent injuries and save lives in the mineral industry, Before I tell you about our program and our future plans, I want you to know that I am here to listen as well as to talk! In my view, the only kind of communication that is meaningful is two-way communication. Our nationwide progress in metal and nonmetal mine health and safety during 1972 cannot be measured in reduced fatalities or injuries. The unforeseen tragedy that took pace in Kellogg, Idaho, in may of last year mode that almost a certainty.

Jan 1, 1973

By Michael A. Linkous, Mark J. Zdunczyk

Silica in the form of sand and sandstone is one of the most common, and at the same time, unique industrial minerals. Found in every rock type of every geologic age and virtually everywhere in the world, silica is used in products that touch just about every aspect of daily life. Imagine a world in the 1990s without computer chips, fiber optics, or glass, and you have just begun to understand how important silica is to the quality of life we enjoy. The elements silicon (Si) and oxygen (0) comprise roughly 60% of the earth's lithosphere to a depth of about 16 km. The crystal structure of silicon dioxide consists of one atom of silicon bonded to four surrounding atoms of oxygen to form a three-dimensional network of SiO, tetrahedra. This network makes up the mineral quartz (Murphy and Henderson, 1983), the most common detrital mineral in most sandstones. Quartz is also a major constituent of many igneous and metamorphic rocks and is widespread as a siliceous cementing agent in various rock types. Although quartz is common, sandstones, quartzites, and pegmatites and the unconsolidated sediments derived from them that have a silica content high enough and pure enough to meet today's market demands for quality and consistency are not common. USES AND SPECIFICATIONS Silica sand that is mined and processed for industrial uses must conform to the chemical and physical specifications set by customers. In the United States almost half of the silica sand produced is used in the manufacture of glass. Other important products include foundry sand, ground silica, blasting sand, and fracturing sand. Glass Sand Silica is the principal glass-forming oxide in a glass batch. Glass manufacturers develop model specifications for each source of silica sand used. These specifications broadly define the limits and ranges for chemical and physical properties of the sand and are used by the manufacturer in calculating the desired batch mix or formula. Some specifications may be critical to a glassmaker and require very stringent limits on the quantity of impurities in the sand. For example, the total iron oxide content of a batch is extremely crucial when making white or flint glasses (Mills, 1983). Iron is present in almost every raw material used in a glass batch and must be carefully controlled in order to obtain a consistent color in the finished product. It is difficult, however, for a raw material supplier to tightly control the chemistry of a naturally occurring material such as silica sand. To a great extent the commercial quality of a sand is determined by its geologic history. Realizing this, glass producers tailor their model specifications to each source of approved material. In general, a glass company is concerned most about the consistency of raw materials on a day-to-day basis. Soda-lime-silica glass was the earliest type of manmade glass (Baker-Can, 1967) and still accounts for most of the glass manufactured for commercial use today (Mills, 1983). It is relatively easy to melt and shape and is less expensive per ton to produce than most other types of glass (Baker-Can, 1967). Soda-lime-silica glass is used in fabricating containers, flat glass products, incandescent and fluorescent lamps, glass fiber, and many other products. Heavy minerals such as ilmenite, leucoxene, kyanite, and zircon are impurities on which strict limits are placed for a glass batch. Because of their refractory nature they either do not melt or only partially melt, which results in stones or feathers in finished glass. Aluminosilicates such as kyanite also contribute unwanted alumina to the batch as they partially melt. Limits are especially rigid for refractory mineral grains coarser than 0.60 to 0.425 mm (30 to 40 mesh). [Tables 1 and 2] present typical specifications for silica sand used in flat glass and container glass products. The percentages shown represent an average of many companies7 specifications.

Jan 1, 1994

By D. Gove

All mining operations using trucks have a common need to properly match the number and size of hauling units (trucks. wagons. scrapers. etc.) to a loading unit (wheel loader. hydraulic shovel/excavator, cable shovel. push tractor. etc.) to provide the best possible fleet match. Optimizing fleet match minimizes the cost per unit of material moved by that fleet. As haul conditions change (haul length. grade. or rolling resistance), there may be need to adjust the number of trucks to maintain the optimum fleet match. Fleet Production and Cost is a tool which, among other things, can be used to optimize the truck-loader match.

Jan 1, 1994

By R. K. Mehta

Conventional triboelectrification based dry coal beneficiation methods require ground coal as a prerequisite feed material, energy intensive static-in-line mixer or cyclonic tribocharger configuration, and transport and/or improvement in the design of free-fall separators to improve the separation efficiency of [me pyrite/mineral matter from coal. The proposed paper illustrates the two concepts. First, the use of ceramic media in a polyurethane lined attitor in achieving simultaneous grinding and differential charging. Second, the use of an electrocentrifuge to selectively separate coal from mineral matter present in the triboelectrified mixture. It is of interest to note that some ceramic media can satisfy the requirements of both desired density and work function to achieve grinding and differential charging.

Jan 1, 1996

By V. M. Torres

Arapiraca ore deposit has a mixed chalcopyritelbornite mineralogy, with a copper head grade of 0.7%. The reserve size does no allow profitable exploration by grinding/flotation. The technical feasibility of exploring the reserve by heap leaching was studied. Preliminary agitation tests indicated 85% copper recovery. To simulate heap leaching, column tests were performed. The tests included different ore types and acid addition levels. Operating at pH range 1.6-1.8, 67% copper extraction was achieved. Also, it was found an empirical correlation between the operation pH range, copper extraction and acid consumption.

Jan 1, 1996

By R. D. Beard

Puerto Rico lies within the remnants of a deformed Cretaceous island arc system in the northeastern Caribbean. The Island can be divided into three broad geologic provinces: the Central Volcanic-Plutonic Province (Lower Cretaceous to middle Eocene), and the Northern and Southern Limestone Provinces (early Oligocene to middle Miocene). Known precious metal deposits are generally small and occur in veins and shear zones within Lower and Upper Cretaceous volcanic and plutonic rocks. Some Tertiary igneous rocks are also mineralized. Selected indications of disseminated lithology-controlled mineralization could represent larger deposits. Associated metals in some deposits include copper, zinc, and lead. At present, tax policies, population density, political outlook, and lack of proven significant precious metal deposits discourage the establishment of a metal mining industry.

Jan 1, 1993

By Fred T. Towne

Recent developments in fine grinding by the means of mechanical impaction are the result of continuing improvements in modern machine construction. This is especially true when related to the bearings and mechanically operated parts of impact mills. These improvements allow manufacturers to increase the speeds of the impacting members Most of the more common forms of size reductions, such as percussion, pressure, friction and sectioning, or cutting were at one time accomplished by human hands. These actions were transferred to machinery. Originally of limited application, their use widened as industrial materials and construction became more sophisticated.

Jan 1, 1965

By Donovan F. Symonds

INTRODUCTION The selection of the optimum coal preparation plant flowsheet is a vital part of the development of a new plant or the expansion of an existing facility. Selection of an inappropriate flowsheet or individual equipment items can result in costly production losses, or needless expenditures or redundant or oversized equipment. The accuracy of the flowsheet selection process is, like most decisions, heavily dependent upon the amount, reliability, and quality of the database. A flowsheet which is based on simple borehole information from an area that has experienced little or no previous mining activity must necessarily include significant allowances for uncertainties. However, a plant which is to be built at an existing mine with good information on run-of-mine (ROM) coal quality, as well as bulk washability data and accurate projections of future quality, can be optimized. The following chapter will describe the processes which should be followed to select the most appropriate flowsheet for each unique operation. They include: 1. Examining and adjusting the washability database to reflect the ROM feed. 2. An evaluation of clean coal specifications. 3. Selection of the level of washing required. This includes no washing, if the coal is already at the desired specification, all the way through to complex total washing circuits for metallurgical grade coals. 4. Selection of the appropriate circuit such as dense medium bath vs. Baum jig. The most appropriate circuit is generally determined on the basis of economics. An approach for performing the evaluation will be desired. 5. The steps that need to be followed to develop a balanced plant flowsheet. ADJUSTING WASHABILITY DATA It is not unusual to have as many as 10 to 20 sets of washability information available for a particular mining property. These may be a combination of core and bulk samples or all bulk samples. In the latter case, they may also be face and/or ROM samples. It is necessary to reduce all of this information to a single set of washability data that is representative of the mean feed to the proposed preparation plant. This set is used to compare the clean coal yield and quality characteristics of the various flowsheet options. The term "representative" has some serious negative connotations. It is recognized that ROM coal quality will vary throughout a mine. However, over a period of 250 to 350 days per year, certain trends can be established. If possible, this "representative" sample should be close to the coal quality of the mean daily sample in terms of raw ash and sulfur contents, clean coal yield, and clean coal ash and sulfur content. If possible, this sample should be within the

Jan 1, 1991