Search Documents

By B. Beatty

Discussion by B. Beatty This is a response to M.J. Hrebar's paper, which tracks in detail the highly productive stripping capabilities of modern large bulldozers at two separate installations. It proves the old adage "economies of scale" and quantifies the advantage of being able to move large loads of dirt over comparatively short haul distances by sliding rather than carrying the load. This discussion examines whether a bulldozer is the most efficient way of using this geotechnical principle. Case 1 - Study eastern US: Contour coal stripping application The energy consumption for the Case 1 mining method (eastern US contour stripping operation) shows the D11 averaged 117 L (31 gal) of diesel fuel per scheduled hour, and produced 333.3 bank m3 (436 bank cu yd) per scheduled hour (0.351 L/m3). Assuming 1 L (0.26 gal) of diesel fuel contains 10.4 kW-hr of energy, the unit expenditure of fuel energy for Case 1 Study was 3.66 kWh/m3. Another way of shifting this material is by using an overburden slusher (OS), as shown in Fig. 1. The OS as shown in Fig. I. The OS is electrically powered and consists of a manned low wall winch (LW ), a remote controlled (radio telemetry) highwall winch (HW) and a hoe. The winches operate to pull the hoe back and forth across the pit. The hoe carries load in the forward direction ahead of a rear mounted blade and returns empty. A spreadsheet (Lotus 123) simulation package, BOSSIM, models the OS operation on a load by load basis over a wide range of pit configurations. The geometry shown in Fig. 2 of the paper was modeled using BOSSI M and the results are summarized in Table1. Table 1 shows a LW with 150 kW (200 hp) and a HW of 120 kW (160 hp) installed power, towing a 15-m3 (19-cu yd) hoe, would accomplish the Case 1 stripping task at about the same scheduled stripping rate (D11=333 m3/hr or 433 cu yd/ hour, OS=342 m3/hr or 447 cu yd/ hour). It was assumed the winches in this equipment have an electromechanical efficiency of 90%. This gives an average electrical energy expenditure rate of 151 kW-hr, and a unit energy expenditure level of 0.44 kWhr/m-3(0.57 cu yd/kWh)-an improvement of 8291%- over the D11 alternative. The energy comparison illustrates the importance of using more efficient electric power if possible, ahead of the internal combustion engine, and delivering power from a fixed ground position rather than through a moving track system. Another important energy observation is the comparative action of the dozer blade and the OS hoe. The former implement continuously digs and spills as it works the load forward. The OS hoe digs the load until full, the blade then lifts due to the contained load pressure and a shear plane forms under the mass, enabling it to slide forward in a force reduced - transporting mode. Economic comparison Table 2 operating cost per scheduled hour and unit cost comparison follows a format used in Tables 2 and 3 of Hrebar's paper and compares Case 1 Study with the OS alternative. Drill and blast costs are kept constant in both cases, although when larger OS units are considered, it is expected these costs will reduce because bigger hoe sizes will permit larger rocks to be transported efficiently.

Jan 1, 1995

By A. A. El-Midany

Traditionally, the choice amongst different upgrading techniques or in finding the optimum operating conditions for a given upgrading technology depends on whether one is looking at the grade or the recovery of the valuable mineral in the concentrate. In fact, the conclusions are not usually the same. This is because the best technique or optimum operating conditions for the highest grade are not the same as the conditions to achieve the maxi-mum recovery. Therefore, a unique measure that takes into consideration both grade and recovery is urgently needed. Finding such a measure is the objective of this paper. A proposed measure provides a selectivity index in the range of 0 to 1, where 0 is no selectivity and 1 is ideal selectivity. The index can be obtained by plotting the so-called Fuerstenau upgrading curve, which relates the recoveries of the components in products of separation and a running regression applying a one-parameter equation. The measure was applied to assess the selectivity of selective flocculation under different operating conditions when used as a sensitive upgrading technique for ultrafine ground ores. After applying the proposed selectivity measure in the case of the selective flocculation of ultrafine Egyptian iron ore without the addition of cations, it was found that the optimum conditions are pH 11, 1 kg/t sodium silicate and 0.4 kg/t potato starch with a selectivity index of 0.55. With the addition of cations, the optimum conditions were found to be pH 11, 1 kg/t sodium silicate and 2 kg/t potato starch with a selectivity index of 0.65. It should be noted that determining these optimum conditions using the traditional grade or recovery measures was highly ambiguous.

Jan 1, 2008

By A. Jennings

[ ] In November 2005, Essroc Cement, part of the Italcementi Group, commissioned a long overland conveyor at their Nazareth plant in Pennsylvania. This conveyor, tagged CV-105, was designed to transport 1000 tph of limestone from the quarry to the kiln, and 400 tph of hot clinker (at 300°F) at back from the kiln to a handling facility about halfway back. Conveyor CV-105 is 8969 ft (2733 m) long. It gains 152 ft (46 m) of elevation in the first 1570 ft (480 m), then is mostly flat for the remaining 7400 ft (2250 m) (Figure 1). After the limestone is discharged at the head pulley, hot clinker is loaded onto the return side of the belt. This clinker can be discharged at one of two locations.

Jan 1, 2012

By Tom B. Corry

INTRODUCTION Located approximately 48 km (30 miles) south of Dallas, Texas, use to be the site of the Superconducting Super Collider. For those of you unfamiliar with the project, this was a multi-billion dollar project taken on by the U.S. Government for the further advancement of technology, medicine, and science. Major components of the project consisted of a Linear Accelerator known as the LINAC; three accelerating rings known as the Low Energy Boosters (LEB), Medium Energy Booster (MEB) and the High Energy Booster (HEB); the East and West Campuses where the Inner Reactor Halls would have been located; and the 87 km (54 mile) main collider tunnel. Unfortunately, this all came to an end on December 6, 1993, with the termination of the project due to the Government's cancellation of funds. This paper will deal with the two of the underground contracts before the termination. These two contracts were the 1122 contract which ran from N25 to N40 and the 1130 contract which ran from N40 to N55. (See figure 1) The 1122 contract was awarded to us in July of 1992 and consisted of the excavation and support of six (6) shaft varying in diameter from 5.5 m (18 feet) to 8 m (26 feet) and ranging from 39.6 m (130 feet) to 61 m (200 feet) deep and the driving of approximately 13,100 m (.43,000 If.) of main collider tunnel. Our second contract, the 1130, was almost identical to our first

Jan 1, 1995

Syncrude Canada produces a large part of Canada’s crude oil supply. The company processes about 225,000 bbl/day. The oil produced is used for jet and automobile fuel, home heating oil, plastics and other consumer synthetics. Crude oil is produced through a process of mining, extracting and upgrading bitumen. A rich supply of bitumen is contained in the Athabasca oil sands deposit in northern Alberta. Tailings from the bitumen processing are sent to a settling basin.

Jan 1, 2000

By Faruk Oksuz, Dave Schiemann, Matt Trotter, Mike Padilla, Carmen Scalise, Miquel Sanchez

"The McCook Main Tunnel system consists of a 10-m (33-ft) finished diameter, 490-m (1,600-ft) long, hard rock tunnel constructed from a 27.5-m (90- ft) diameter and 92-m (300-ft) deep main gate and tunnel construction access shaft. The gate shaft houses six, high-head 4.4 m by 9 m (14.5 ft by 29.5 ft) wheel gates to be installed in the bifurcated and steellined section of the tunnel. The tunnel also includes portal and energy dissipation structures as it daylights into the reservoir.The construction of the tunnel system has been divided into two contracts. The gate and construction access shaft was completed in August 2011. The tunnel excavation and concrete and steel lining was completed in September 2014. The remaining and undergoing construction include the tunnel connections to the reservoir and the Mainstream Tunnel and installation of gates and hydraulic cylinders. This article focuses on the live connection of the McCook Main Tunnel to the Mainstream Tunnel that was initiated in November 2014 and will continue through the seasonal drier weather conditions in Chicago approximately from October through April. Chicago TARP systemThe MWRD has been addressing combined sewer overflows (CSO) and flooding in Chicagoland since the late 1960s and formally adopted the tunnel and reservoir plan in 1972 to protect the region’s most precious drinking water supply, Lake Michigan. Phase I of TARP, which included construction of 175 km (109 miles) of deep storage and conveyance tunnels with diameters up to 10 m (33 ft), was completed in 2006. In addition to protection of Lake Michigan from CSO discharges, Phase I resulted in substantial improvements in surface water quality as well as the quality of life for lake and riverfront communities in Chicago. Water quality improvements and flooding mitigation will be further enhanced as Phase II reservoirs are placed in service, including the three large reservoir systems, McCook, Thornton and Majewski (Fig. 1).The McCook Reservoir is the largest reservoir in the TARP system. Once completed, this $700-million reservoir facility will receive 38 billion L (10 billion gal) of CSO and flood water via the McCook Main Tunnel, which connects the TARP Mainstream Tunnel to the McCook Reservoir, and from distribution and Des Plaines inflow tunnels which will bring flow from the Des Plaines Tunnel of TARP."

Sep 1, 2016

By Qinbo Cao, Qianshan Peng, Heng Zou, Xingcai Yu

In this work, a new flotation strategy was proposed for the flotation of rutile. In this strategy, rutile was activated by Pb(NO3)2 and then floated with amyl xanthate (AX) as a collector at pH 8. Pb(OH)+ was the dominant lead species in the solution at pH 8 and is believed to be the major species reacting with the rutile surface. Time-of-flight secondary ion mass spectrometry (TOF-SIMS) study revealed that the lead activation products were well distributed on the rutile surface, and AX− could further bind with the Pb atom on the Pb-activated rutile surface. In this regard, the Pb-activated rutile could be floated by AX. Furthermore, X-ray photoelectron spectroscopy (XPS) analysis indicated that Pb(OH)2 was generated on the Pb-activated rutile surface. The electron transfer during the adsorption of the AX− on the Pb-activated rutile surface was also investigated by XPS analysis.

By Qinbo Cao, Qianshan Peng, Heng Zou, Xingcai Yu

In this work, a new flotation strategy was proposed for the flotation of rutile. In this strategy, rutile was activated by Pb(NO3)2 and then floated with amyl xanthate (AX) as a collector at pH 8. Pb(OH)+ was the dominant lead species in the solution at pH 8 and is believed to be the major species reacting with the rutile surface. Time-of-flight secondary ion mass spectrometry (TOF-SIMS) study revealed that the lead activation products were well distributed on the rutile surface, and AX− could further bind with the Pb atom on the Pb-activated rutile surface. In this regard, the Pb-activated rutile could be floated by AX. Furthermore, X-ray photoelectron spectroscopy (XPS) analysis indicated that Pb(OH)2 was generated on the Pb-activated rutile surface. The electron transfer during the adsorption of the AX− on the Pb-activated rutile surface was also investigated by XPS analysis.

By Syd S. Peng

Introduction The most commonly used ground control design in coal mining is the determination of pillar size by various pillar strength formulae for mine layout (Bieniawski, 1983; Holland, 1973; Hustrulid, 1976; Obert and Duvall 1967; Wilson and Ashwin, 1972). However, there have been few documented case histories concerning the validity of those strength formulae. Recently there are indications that those strength formulae tend to overdesign considerably. From a safety point of view, there is nothing wrong with overdesign. But an overdesign with large chain pillars reduces the flexibility of machine movement and decreases production. It also reduces coal recovery and, thus, shortens the reserve's life. This is especially true for small operators who own a limited reserve. Those small mines, through past practices or out of necessity, experiment with smaller pillars than those predicted by the strength formulae. Conclusive ev¬idence has been collected that points to the need of a new concept of coal pillar design. Two case studies will be cited to illustrate this point. 3-D US pillar strength formulae Figure 1 shows a sectional layout of a one-unit mine. The seam was about 1.3 m (50 in.) thick with a uniform cover of 64 m (210 ft). A house was located near the center of the section. The homeowner demanded that no surface subsidence and domestic well dewatering should ever be allowed as a result of underground room-and-pillar mining. Physical properties - strength and Young's modulus - of the rock strata including coal were obtained by testing small samples in the laboratory. The uniaxial compressive strength of the coal was 3660 kPa (823 psi). Using various pillar strength formulae, the homeowner recommended that square chain pillars be at least 11 m (35 ft) wide. The coal company, however, desired to pursue optimum coal recovery in the safest and most economical manner. They engaged in three-dimensional finite element analysis of the section taking into account the complete stratigraphic sequence of the overburden. Results indicated that the section can be developed by 5.5 m (18 ft) wide entries at 21 m (70 ft) center-to-center. In retreat, the pillars can be splitted along both centerlines leaving a stump pillar of 5.5 m (18 ft) square at each of the four corners. The 5.5 m (18 ft) square stump pillars still maintained a safety factor of 1.5, although the safety factors calculated by various pillar strength

Jan 11, 1986

By A. B. Cecala

A few years ago, the National Institute for Occupational Safety and Health and Unimin Corporation developed a clothes cleaning system that is able to quickly, effectively, and safely remove dust from a worker?s clothing without dust exposure to the worker, the work environment, or co-workers during the cleaning process. To perform the process, a worker enters a cleaning booth and activates an air spray manifold which blows the dust from the worker?s clothing. Since the cleaning booth is under negative pressure, all the dust and product removed are contained. In the original design, this dust-laden air was exhausted to a dust collector system. However, since most operations do not have excess dust collector capacity, it was decided to determine an alternative method to provide for a stand-alone cleaning system. This was achieved by ducting the exhaust outside the plant and into the atmosphere. This technique was recently tested and shown to be a viable method to provide for a stand-alone clothes cleaning system.

Jan 1, 2009

By John Addison

Experimental animal studies comparing asbestos and non-asbestos varieties of tremolite indicate tremolite asbestos is markedly more carcinogenic. By direct analogy, the differences in carcinogenicity between tremolite asbestos and non-asbestos prismatic tremolite should be the same for the other types of amphibole that also crystallize in the asbestos and non-asbestos habits. The earliest of the experiment animal studies, done more than 25 years ago, have design limitations by modern standards including the use of injection or surgical implantation as the route of administration rather than the more relevant route of inhalation. However, the differences in the carcinogenicity of amphibole asbestos and non-asbestos amphiboles are sufficiently large to be clearly discernable even with the study limitations. Together with later studies on these and related minerals, there is strong evidence of a much lower hazard associated with the shorter, thicker fibers of the non-asbestos amphiboles, than is found for the asbestos analogues of the same mineral. It is possible that the non-asbestos amphiboles are no more hazardous than other silicate minerals widely considered nuisance dusts. © 2007 Elsevier Inc. All rights reserved. Keywords: Amphibole; Asbestos; Tremolite; Carcinogenic

Jan 1, 2007

By N. Paas

Diesel powered equipment has been operated in underground coal fir mare than 50 years. According to the Mine Safety and Health Administration (MSHA), there are approximately 3,000 diesel units operating in underground coal mines in the United States. This number is expected to reach 5,000 diesel units in 250 coal mines by the year 2000. Also, there are approximately 5,000 diesel units operating in metal/nonmetal mines such as trine, potash and salt mines: and more than 3,000 diesel units operating in Canada. This increased popularity of diesel powered equipment over trolley wire, electric trailing cable or battery powered equipment is because of improved safety, greater mobility, higher productivity and increased power of diesel equipment. The operation if diesel powered equipment is not without challenges. Diesel engines generate exhaust emissions, in particular carbon monoxide, oxides of nitrogen, sulfur dioxide, unburned hydrocarbons, and diesel particulate matter that must be maintained at safe levels. The chief method to control ambient exposure has been dilution by ventilation. A new concept to ensure continued safe ambient emissions levels from diesel equipment in underground mines is the EMISSIONS MANAGEMENT PROGRAM™. The program encompasses all factors that will influence diesel emissions. By ESTABLISHING low tailpipe emissions through technology, such as clean engines, clean fuel selection, exhaust aftertreatment devices and filtration of the exhaust gases via the Dry System ™, this program ensures that the baseline emissions are at their lowest technically feasible concentrations. The DST Dry System™ exhaust conditioner reduces DPM by over 98%, as demonstrated through laboratory research at the West Virginia University. Carbon monoxide and hydrocarbon emissions and odor are similarly reduced. MAINTAINING these low emissions requires an expanded training program for operators and mechanics, onboard feed-back devices and a maintenance program with special focus on events and faults that can alter emissions. Finally, an on-board emissions sampling system allows the mechanic to VERIFY emissions levels and help diagnose engine faults. If the tailpipe emissions fall outside an established limit for a particular equipment, corrective actions will be initiated.

Feb 24, 1997

By Jan Van Greunen, Mark Vanderzee, David Haug, Geoffrey Hughes, Yiming Sun, Roozbeh Geraili Mikola

"The Sanitation Districts of Los Angeles County is planning to construct a new, approximately 7-mile-long (11.3 km) effluent outfall tunnel to be excavated by TBM and lined with precast concrete segments. Anticipated net operating pressures within the tunnel are expected to approach 3 bar. To counteract joint opening and exfiltration leakage, an approach has been investigated to post-tension the precast concrete tunnel lining with steel tendons. The tunnel alignment crosses several seismically active fault zones, at which installation of steel pipe is proposed as a secondary inner lining to mitigate potential offset displacements. This paper discusses the tunnel lining design approach and methods used to address these unique challenges.INTRODUCTION The Sanitation Districts of Los Angeles County (Sanitation Districts) is planning to construct a new 18-foot-diameter (5.5 m), approximately 7-mile-long (11.3 km) tunnel from the Joint Water Pollution Control Plant (JWPCP), located in the City of Carson, to the existing White Point outfall manifold structure at Royal Palms State Beach (RPSB) (Figure 1). The project is part of the Sanitation Districts’ Clearwater Program, which will improve overall system reliability through the repair and replacement of the existing aging infrastructure. The existing system includes two 6-mile-long (9.7 km) tunnels, 8- and 12-feet in diameter (2.4 and 3.7 m), and four ocean outfall pipes with a maximum capacity of approximately 675 million gal/day (MGD) (2.6 billion L/day). Addition of the new parallel tunnel will increase overall capacity to accommodate peak wet weather wastewater flows of up to 1,262 MGD (4.8 billion L/day) and will allow inspection and repair of the existing tunnels. The new outfall tunnel will be excavated using a pressurized face tunnel boring machine (TBM). Shafts at the north (JWPCP Shaft) and south (RPSB Shaft) ends of the proposed alignment will connect the tunnel to the existing wastewater treatment plant and existing ocean outfalls manifold and during construction act as launch and receiving shafts for the TBM. The tunnel will be excavated from north to south as a single heading."

Jan 1, 2016

By P. Zhang, S. Al-Thyabat

"Phosphate rock contains traces of rare earth elements (REEs) and can be a secondary source of these critical materials as large tonnages of phosphate rock are mined annually. Attention has mostly focused on the extraction of REEs from phosphogypsum, which contains more than 70 percent of the REEs reporting to phosphate concentrate, with only limited work conducted on REE extraction from sand tailings and slime even though they account for 16 percent and 15 percent, respectively, of REEs mined with phosphate matrix.In this work, phosphate flotation tailings were upgraded by gravity separation and froth flotation. Gravity separation was conducted using a laboratory shaking table, while flotation was conducted in a Denver D-12 flotation cell. The concentrated tailings were then leached by nitric acid followed by REE extraction with solvent and ion-exchange resin.The sand tailings were assayed as having 2.6 percent phosphate (P2O5 ) and 198.1 µg/g REEs. It was found that the shaking table could produce tailing concentrate assayed as having 8.6 percent P2O5 and 616 µg/g REEs but with only 20 percent REE recovery, while the froth flotation produced froth concentrate assayed as having 8.1 percent P2O5 and 368.2 µg/g REEs with 63.5 percent REE recovery. Leaching the flotation concentrate with 5.2 M (25 percent) nitric acid followed by extraction with solvent and ion-exchange resin yielded precipitates with REE contents of 0.926 and 0.314 percent, respectively, compared with 0.716 and 0.213 percent when table concentrate was used.IntroductionRare earth elements (REEs) consist of a group of 17 elements: the 15 lanthanides along with yttrium (Y) and scandium (Sc). They are rare not because of their scarcity in the Earth’s crust but because they are rarely found in economic and mineable deposits. REEs are called “seeds of technology” because of their importance to some critical technological industries such as renewable energy, hybrid cars, electronics and batteries. On average, an electric car or a hybrid car contains about 10 kg of REEs (Grasso, 2012; Radhika et al., 2011).REEs are usually categorized into light (LREE) and heavy (HREE). LREEs consist of lanthanum (La), cerium (Ce), praseodymium (Pr), neodymium (Nd), promethium (Pr), samarium (Sm), europium (Eu), gadolinium (Gd) and scandium (Sc), while HREEs consist of terbium (Tb), dysprosium (Dy), holmium (Ho), erbium (Er), thulium (Tm), ytterbium (Yb), lutetium (Lu) and yttrium (Y). About 200 minerals contain traces of REEs, but only three are considered economically significant: bastnasite, with the formula La,Ce(CO3)F; monazite, with the formula(Ce,La,Nd,Th)PO4; and xenotime, with the formulaYPO4 (Jordens, Cheng and Waters, 2013)."

Jan 1, 2016

Two miners were fatally injured when a pillar bump occurred during retreat mining in a southern West Virginia coal mine. The mine was operating in the Eagle seam with overmining in the No. 2 Gas and Powellton seams. A coal bump is defined as a sudden and violent failure of coal caused by the release of stored strain energy in the pillar. While significant strides have been made by academia, industry, and regulatory agencies to better understand bump conditions and mitigation techniques, coal bumps represent a long standing, highly site-specific engineering problem in which the exact failure mechanism(s) is not clearly understood.

Jan 7, 2020

By Jimmy Thompson

The Santa Clara Valley Transportation Authority is designing the Silicon Valley Rapid Transit Project in San Jose, California. The project includes 6.9 km (4.3 miles) of twin-bored tunnels to be constructed through downtown San Jose using two earth pressure balance machines (EPBMs). This paper begins with a project description and update of the project status followed by a description of the relationship between anticipated ground conditions and EPBM requirements. Topics addressed include soil conditioning, abrasion resistance, annulus grouting, face pressure estimation, additional pressure control devices and control measures to limit over-excavation and settlement.

Jan 1, 2008

By W. J. Guay

Carbonaceous gold ores containing gold dispersed in sulfides are refractory to cyanidation because: (1 ) the carbonaceous materials adsorb gold during cyanidation; (2) a portion of the gold s so finely dispersed in the sulfide mineral lattice as to preclude contact with cyanide solution; and (3) a portion of the gold is chemically combined with carbonaceous material. Techniques which have been used to treat these ores are: (1) roasting or chemical oxidation to decompose sulfide and carbonaceous materials; (2) flotation to reject carbon; (3) the use of kerosene or other reagents to passivate the adsorptive carbon compounds; (4) carbon or resin in pulp; (5) flotation of a bulk concentrate which is treated by one of the above methods; and (6) the use of chelating agents which have a stronger affinity for gold than the activated carbon in the ore.

Jan 1, 1981

By Umay Cinarli, Ahmet Turan

High-energy consumption in primary aluminum production (from bauxite ores) makes secondary aluminum production (from metallic raw materials such as scrap and dross) very critical. Aluminum dross, as a waste, arises in pyrometallurgical processes, and it is the mixture of metallic Al, Al2O3, other metal oxides, metal halides, and some other compounds like AlN. Aluminum dross has two subgroups (white and black) with respect to its metallic aluminum content. White dross is a secondary aluminum resource because of its high metallic aluminum content, whereas black dross, having low metallic aluminum content, is generally disposed in dumping areas. In the present study, it was aimed to develop a simple technique to valorize aluminum black dross in the form of alumina-based ceramic materials through pyrometallurgical (calcination) and hydrometallurgical (leaching) operations. Moreover, thermochemical simulations were conducted by using HSC Chemistry 6.12 software to simulate calcination conditions. After leaching experiments, an alumina-based ceramic containing approximately 36.8% Al2O3, 61.4% MgAl2O4 with 1.8% Na2FeO4, which might be available to use as a spinel refractory in steel smelting furnaces, was obtained in the experiment carried out in a solution containing 10 mLH2SO4 and 40 mL distilled water (3.5 M). Moreover, the sinterability of the alumina-based ceramic was investigated at the temperatures from 1350 to 1550 °C. In the sample which was sintered at 1550 °C, a density value of 3.15 g cm−3 and a hardness value of 69.58 HV were measured.

Oct 26, 2020

By Dean Workman

Located in downtown New York City, this project necessitated an innovative conveyor design for successful muck removal. This paper will discuss the technical challenges and engineering solutions of the muck transport system which consists of every commonly recognized version of a belt conveyor. The elaborate system includes a TBM conveyor integral to the back-up system, a wall-mounted extensible conveyor, a crown-mounted transfer conveyor, a floor-mounted fixed-length conveyor, a pocket-belt vertical conveyor, three cascading overland conveyors, and one radial stacker. The most challenging design element was an over-land conveyor featuring a box truss for muck transportation over Northern Boulevard while simultaneously going under the Queens Plaza railroad viaduct. An overview of the project is provided along with the following topics: developing final plans from the proposal concept, interfacing with existing works, communication with the joint venture, and complying with local regulations.

Jan 1, 2008

By Steve Kral

Globalization was the key word for the mining industry during the 1990s, just as productivity was the key word of the 1980s. And globalization will remain the key word as the industry enters the 21st century, according to speakers at the Colorado MPD Meeting held in Colorado Springs, CO in May. The meeting, put on by the Colorado Section SME Minerals Processing Division, drew about 120 people to the Broadmoor Hotel. “Operating Globally” was the theme of the 49th annual conference. Speakers addressed the reasons why mining companies have limited their spending in the United States and have moved into Third World and developing nations.

Jan 1, 1999