Search Documents

By E. A. Martell, K. S. Sweder

INTRODUCTION Lung cancer in uranium miners has been attributed to alpha irradiation of basal cells of the bronchial epithelium by radon daughters, primarily by 7.7 MeV alphas from polonium-214 (Altshuler et al., 1964). It also has been was observed that for a given cumulative radon progeny exposure, uranium miners who smoke cigarettes have an incidence of lung cancer about 10 times higher than nonsmoking miners (Lundin et al., 1969). It has been pointed out that the large excess of lung cancer deaths among smoking uranium miners is a multiplicative effect (Doll, 1971), which suggested possible synergistic interactions between airborne radon progeny and cigarette smoking. Experimental studies of the complex pattern of interactions between radon progeny, cigarette smoke particles, and the cigarette smoking process are in progress in our laboratory. Preliminary results, reported elsewhere (Martell, 1981), implicate alpha radiation from indoor radon progeny in the etiology of lung cancer in all cigarette smokers. Cigarette smoking produces high concentrations of smoke particles of low mobility and respirable size--particles between 0.5 and 4.0 µm in aerodynamic diameter (see below). The attached fraction of indoor radon progeny is highly dependent on the air concentration of small particles from cigarette smoking and from other combustion sources (Martell, 1981). The size distribution and other properties of radon progeny associated with cigarette smoke particles enhances their effectiveness in the induction of bronchial cancer in man. In this paper we discuss the properties of radon progeny associated with cigarette smoke, the fractionation of radon progeny and modification of their aerosol properties in burning cigarettes, the role of 218Po in these processes, the production of insoluble 214Pb and 212 Pb enriched particles in burning cigarettes, and the consequent differences in the patterns of polonium isotope alpha irradiation in the bronchial epithelium of smokers. EXPERIMENTAL PROCEDURES Experimental methods used in these studies involve the use of small experimental chambers of known radon and radon progeny concentrations in combination with aerosol collection and sizing techniques and sensitive radioactivity detection methods. The use of low-level [ß-] counting for radon progeny determination, providing a measure of 214 Pb plus 214Bi activity, makes it possible to carry out chamber experiments with small radon emanation sources and relatively low air concentrations of radon and radon progeny concentrations in the range from 100 to 1,000 pCi per liter. Thus, for example, in a typical experiment we use a 10 nanocurie 226Ra solution standard in a 10 liter chamber, providing an equilibrium concentration of 1,000 pCi of radon per liter. In small sealed chambers, radon progeny plate out rapidly on the chamber walls, with steady-state concentrations of airborne progeny less than 2 percent of equilibrium levels. This is experimentally convenient because, upon introduction of high concentrations of cigarette smoke particles or small particles from other sources, there is a systematic ingrowth of attached radon progeny, providing a tagged aerosol source of known age and radon progeny composition. In some chamber experiments a 226Ra solution standard of small volume, acidified to O.1N HNO3, was used as the radon emanation source. When used with a bubbler the holdup of radon in an 8 ml volume of 226Ra solution standard at 0.1N HN03 was only 2% of the total radon in the chamber at equilibrium. For experiments with 212Pb-tagged aerosols, we used a dry Ba(228Th) stearate emanation source prepared by the method of Hursh and Lovaas (1967). 226Ra and 222Rn determinations were made by radon gas counting. The 222Rn in a sealed air or water sample is transferred, using helium gas as a carrier, successively through a dry ice cooled trap at -80°C to remove water, through ascarite to remove C02, and through a small activated charcoal trap at -80°C to collect the 222Rn. Subsequently, by heating the charcoal to 400°C, the 222Rn is transferred next to an LN2-cooled capillary trap, and finally into an alphascintillation counting cell of the type described by Lucas (1957). As already stated, radon progeny activities were determined by low-level [ß-] counting, which provides a measure of 214Pb plus 214Bi. The radon progeny samples, collected on efficient Delbag polystyrene micro-fiber filters or on impactor foils, are placed in close, sandwich geometry between two thin-walled flow counters inside shielding anticoincidence counters and a 15 cm thickness of steel shielding. This configuration provides nearly 4II geometry and a low background of only 0.25 to 0.30 cpm. Aluminum absorber was added to provide a combined thickness of absorber and counter wall exceeding 7.0 mg/cm2 to eliminate the variable contribution of 7.7 MeV alphas from 214Po. 212 Pb determinations also were carried out by low-level [ß-] counting, in this case using a combined absorber and counter wall thickness of 9.0 mg/cm2 to eliminate contribution of 8.8 MeV alphas of 21 Po. In each experiment the [ß- ]activity data were corrected for decay to an appropriate common reference time for assessment of activity distributions.

Jan 1, 1981

By M. T. Long

The Crestmore Limestone Mine of Riverside Cement Company in Riverside, California is situated within 1.6 km of the Santa Ana River. It is an alluvium covered deposit with a massive quartz manzonite intrustion separating the upper and lower limestone beds which dip from 30° to 50°. The highly fractured upper bed contacting the Santa Ana alluvium contains many unique water inflow problems which vary, from multiple high pressure 19 liters per minute inflows up to 3,000 liters per minute to 11,000 liters per minute inflows-contacted by development mining in April 1983. A case history of the successful grouting of these inflows and the continual grouting procedures in advance of present mining with empirical' results are discussed.

Jan 1, 1984

By L. R. Chirinos

The Tintaya mine of BHP Copper, located in Southern Peru, includes a copper oxide deposit hosted in a mineralized skarn zone. The ore contains large amounts of clays and high acid consuming species resulting in low heap leaching performance. A treatment scheme was proposed that included a wet screening separation. The coarse fraction would be treated by heap and the fines by agitation leaching. The dissolved copper would then be recovered through solvent extraction and electrowinning (SXEW). Testwork determined the optimum heap leaching conditions to treat the oxide in on/off pads of 3 meter height with an initial acid cure followed by variable acid strength during irrigation. The method resulted in a reduced acid consumption and good copper recoveries.

Jan 1, 1997

By N. L. Parduhn

Populations of Bacillus cereus spores are elevated in soils over four subsurface gold deposits in the western United States. Large deposit-to-background ratios of B. cereus populations were obtained in soil traverses over the Minnesota vein deposit, Empire District, Colorado (maximum 50:1); the Shasta (maximum 3,500:1), and Evening Star maximum 18,000:1) vein deposits, Shasta County, California; and the Hog Ranch disseminated gold deposit (maximum 40,000:1) in Washoe County, Nevada. Small increases in the concentration of toxic metals in the soil may be responsible for the elevated spore populations. The observed elevation of B. cereus spore populations near these gold deposits indicates that the method should be further investigated as a potential exploration tool.

Jan 1, 2013

By Lawrence P. Bonicatto

The steel industry's increased demand for higher grade pellets has caused the pellet producers to investigate methods of upgrading their product. The Hanna Mining Company's Groveland plant is no exception. The Groveland Mine is located in Dickinson County on the Upper Peninsula of Michigan. The low grade iron deposit is a complex mixture of magnetite and hematite with chert, quartz, jasper, and various iron silicates. (1) Beneficiation is by Humphrey spirals and anionic flotation of the iron minerals. (2) A general flowsheet is shown in Figure 1. Flotation of the spiral tailings makes up about 75% of the concentrate. A minor amount of concentrate, less than 3%, is produced in magnetic circuits. The concentrate is pelletized at the rate of 1.6 million tons per year.

Jan 1, 1968

By Jorgen Elbrond

Shovels, trucks and repair bays for the trucks each play their role in the capacity of an open pit operation. It is therefore convenient to have a procedure for the capacity calculation which takes all 3 factors into consideration in a comprehensive manner. This can be done by means of a cycle model, earlier developed for the shovel-dumper circuits, when the repair facility with its number of repair bays is added as a superimposed service system, which the trucks visit at certain specified intervals. The calculation model transforms the mechanical availability of the trucks into their operational availability. The system's capacity in truckloads per shift and the trucks' operational availability of certain combinations of shovels, trucks and repair bays are shown.

Jan 1, 1981

By Matthew E. Fowler, Jean Habimana, Roy F. Cook

The West Side CSO Tunnel, Pump Station & Pipeline Project is currently beginning construction along the downtown waterfront of Portland, Oregon. This4.3 meter diameter, 5,500 meter-long soft ground tunnel will be driven along the westbank of the Willamette River adjacent to buildings and utilities and several major pile-supported bridges. High groundwater pressure, extended lengths of gravel to cobble-size alluvium, and the need to control ground loss and surface settlements were key considerations in the selection of slurry tunnel boring machines for the project This paper presents an overview of the numerical modeling that was performed during design to estimate the strains and additional loads in the pile-supported structures and to assess the efficiency of proposed mitigation measures.

Jan 1, 2003

By J. S. Gardner, K. E. Houston, A. Campoli

INTRODUCTION Disposal of coal refuse is a costly and challenging problem facing the coal industry today. After the Martin County Coal Company slurry spill and the subsequent regulatory changes state and federal agencies are now beginning to require companies to justify new slurry impoundments. The authors have performed an analysis of different means of disposing of coal refuse for a major coal producing company located in the eastern Kentucky coalfields (the name of which will be withheld for the purpose of this paper). The company’s existing slurry impoundment is nearing its maximum permitted elevation and also an elevation where it may come in contact with abandoned underground workings. Due to the increased concern with underground mine works near slurry impoundments, additional consideration was given to raising the existing impoundment. Several other alternatives were evaluated, including but not limited to raising the existing impoundment, constructing a new slurry impoundment, constructing slurry cells, belt presses and others. This alternatives analysis was performed as part of a Section 404 permit for a valley fill and is currently being reviewed by the U. S. Army Corp of Engineers. All of the known possible alternatives were discussed in detail in the analysis. Due to the findings of the alternatives analysis, the company considers the engineered construction of the proposed impoundment to be the most favorable option of all the other alternatives evaluated, from both an economic and environmental standpoint. ALTERNATIVES EVALUATION FOR COALREFUSE/SLURRY DISPOSAL Background The company currently operates several deep mines and employ over 300 people and produces over 3.9 clean Mt/a (4 million stpy) of high quality, low sulfur coal. Currently, coarse refuse is belted to a valley fill, while, fine refuse is pumped to the existing impoundment. Coarse refuse is trucked to the existing impoundment as needed for construction purposes. The average recovery is approximately 50%; therefore, over 3.9 Mt/a (4 million stpy) of coal refuse must also be separated and placed.

Jan 1, 2003

By John B. Jones

New concepts in shaft kiln processing are included in the design of two large diameter shaft kiln plants now under construction. One kiln will be used to produce cement clinker at the Boettcher plant of the Ideal Cement Company at Fort Collins, Colorado. The other kiln is for the semi-commercial oil shale plant for Petrobras, the Brazil National Oil Company at Sao Mateus do Sul, Parana, Brazil. Investigations on application of the new concepts are proceeding in a portable pilot kiln. The shaft kiln has long been recognized as a method of gas-solids contacting having the following principle advantages: l. High thermal efficiency 2. Ability to handle a variety of feed materials with a wide range of particle sizes 3. Minimum investment and operating cost

Jan 1, 1963

By William K. Burriss

Computer technology was applied to solve three problems in the selling of certain industrial minerals to the glass and foundry industries. The computer solutions provide for better service to customers and have helped increase sales. II. Summary Electronic data processing techniques were applied: 1. To automatically and continuously "trace" rail car shipments of bentonite. 2. To aid our sales people in recommending to glass plant purchasing agents which of several possible feldspathic materials is the best value at any of about 100 glass plants and to give guidance on the amount of value difference. 3. To help in locating plant sites for three blending or pre-mixing stations to serve the foundry industry at minimum cost and with maximum tonnage and maximum profitability.

Jan 1, 1968

By Rob Robertson

The problem of fine coal slimes has been addressed in a unique way at A. T. Massey Coal?Company. Several plants have employed two-stage classifying cyclones to separate the minus 1 mm raw coal into 3 sizes. Larger cyclones make the initial cut at approximately 150 µ (100?mesh) sending the underflow to a cleaning circuit (usually spirals) while the overflow is pumped to a secondary cyclone circuit using smaller cyclones. The small cyclones make a cut at near 70 µ (200 mesh) and produce an underflow that is a des limed flotation feed. The overflow is discarded to refuse due to its high ash and superfine size which would produce a high moisture product even if suitably recovered.

Jan 1, 1998

By Charles N. Alpers, D. Kirk Nordstorm

A variety of approaches have been used in the recent literature for the estimation of pre-mining (or natural background) metal concentrations in areas affected by mining. The following is a list of some of these approaches: (1) historical and anecdotal data, (2) remote analogues (other similarly mineralized areas), (3) proximal analogues (nearby mineralized areas), (4) sediment sampling (streambeds, lakes, estuaries, floodplain deposits, and soil profiles), (5) stable isotopes (hydrogen, oxygen, sulfur, and carbon), (6) geochemical modeling (forward, equilibrium-based), (7) geochemical modeling (forward, kinetic- and transport-based, and inverse), (8) statistical analyses, (9) mass balance on oxygen flux, (10) mass balance with age determination of weathered material. Examples of each approach are described, and the strengths and limitations of each approach are discussed.

Jan 1, 2000

By Gennaro G. Ph. D Marino

In order to improve handling of subsidence damages the Illinois Mine Subsidence Insurance Fund supported the development of novel cost-effective methods of repair. The research in developing the repairs was directed towards the most common and costly damages that had been observed. As a result repair techniques were designed for structurally cracked foundations in the tension zone; structurally cracked foundations in the compression zone; and damaged or undamaged tilted foundations. When appropriate, the postulated methods would result in: 1. significant cost savings (over conventional procedures); 2. a structural capacity greater than when the foundation was untracked; and 3. an aesthetic appeal. All the postulated repair methodologies were laboratory and/or field tested. The paper will summarize the essentials of each technique developed and the test results.

Jan 1, 1986

By J. L. Gent

Compressed air distribution networks are essential for powering equipment in many mines even though some mines are replacing them with electrical power for hydraulic drills. Compressed air can be costly especially if the system is poorly designed and maintained. This paper outlines a technique for proper compressed air system design that will help mine managers reduce compressed air power costs; an important topic in today's highly competitive international minerals market. Compressed air system design is complex. It requires specifying: 1) air quantity and pressure in all branches of a large network, 2) proper location and types of valves and fittings, 3) the network solution that determines compressor requirements, 4) optimal hose and pipe, diameters, 5) receiver and compressor accessories, and 6) required capital and operating costs.

Jan 1, 1989

By A. E. Isaacson, T. H. Jeffers

The U.S. Bureau of Mines (USBM) is investigating arsenic removal from dilute waters using a biological precipitation/chemical adsorption system. The method includes (1) inoculating water with ferrous salts to increase hydrogen sulfide generation by indigenous sulfate-reducing bacteria, (2) utilizing the hydrogen sulfide to precipitate the bulk of the arsenic as arsenic sulfide, and (3) using beads containing ferric oxyhydroxide to remove the remaining arsenic. This approach was applied to a contaminated water containing 13 mg/L As. Arsenic extractions up to 99% were achieved. The use of sulfate-reducing bacteria is particularly warranted in this situation since most of the required nutrients are present in the water. Based on successful initial efforts, planning is underway to conduct a pilot-scale test at the site.

Jan 1, 1995

By Mandira Madhuchhanda, N. B. Devi, P. C. Rath, R. K. Paramguru, K. Srinivasa Rao

An experimental investigation of the dissolution of three base-metal sulfide minerals, namely, CuFeS2, ZnS and PbS, in hydrochloric acid medium in the presence of manganese dioxide is reported. Polarization measurements and leaching studies were employed in the study. Dissolution occurred in the following three ways: by the cyclic action of the Fe3+/Fe2+ redox couple, by galvanic interaction between Mn02 and the sulfide minerals, and because of chlorine evolution from the system. The later two routes were found more effective at higher HCI levels. PbS appeared to be oxidized easily, whereas CuFeS2 was the most difficult to dissolve. ZnS dissolution fell in between PbS and CuFeS2.

Jan 1, 2002

By J. Kemeny, B. Norton, T. W. BoBo

Digital image analysis systems to quantify particle size of crushed materials have successfully been applied in large-scale mining operations throughout the world. Particle size measurement at various crushing and sieving stages, especially in aggregate production, will facilitate the industry’s desire and need to achieve higher levels of process control and automation. This paper will 1) summarize applications of digital image analysis in the industrial minerals industries and introduce the Split-Online technology; 2) detail an actual recent test application of digital image analysis that ultimately lead to the installation of an automatic, non-invasive particle size distribution monitoring system; 3) document how this information is being applied: and 4) summarize the new Split-Online Aggregates Module now available.

Jan 1, 2004

By Michael G. Nelson, Brandon J. Peterson

Currently, decisions made by mine management are usually based on economic analysis and predetermined rating systems and tables. As financial and other constraints on mining operations become more severe, more accurate methods are required. Discrete-event simulation programs have been used successfully in many mining applications, including the simulation of open-pit, truck-and-shovel operations. However, these simulations could not model complex systems well enough to provide the detailed modeling of the haulage roads and other mining operations that is needed today. The recent advances in computing technology combined with the recent abilities of simulation to realistically simulate complex systems and visually present results in 3D have made simulation a more detailed and valuable aid in the evaluation of mining projects.

Jan 1, 2002

By M. C. Roberts

In assessing the future markets for a mineral from a producing district, three key aspects must be considered: 1) the future growth in markets, 2) the competitiveness of the district in terms of production costs and reserve adequacy, and 3) the competition from alternative sources of supply. This paper will focus on the first issue by developing a method of predicting the demand for phosphate from the trends in the major markets for phosphate products, primarily the fertilizer and agricultural markets. The paper will show how broad changes in the final end use markets for phosphate products have evolved over time and how this has affected the needs for phosphate rock. These trends are then projected into the future to make an assessment of future phosphate requirements.

Jan 1, 1998

By K. R. Gardner, P. B. Altringer, R. H. Lien

The Bureau of Mines, U. S. Department of the Interior, is investigating biological and chemical reduction of selenate and selenite from waste waters. A mixed bacterial culture, isolated from agricultural waters, removed selenium from four oxidized cyanide solutions from precious metals operations containing 0.6 to 30 ppm Se and 13 ppm CN. Up to 85% selenium removal was attained using bacteria under controlled batch conditions in a 3-L stirred tank reactor and in small-scale continuous tests conducted in a rotating biological contactor (RBC). Fe(OH), reduction of the selenium reduced the effluent concentration to 0.02 ppm Se; however, the reagent costs were prohibitive. A final processing scheme may involve a combination of biological and chemical treatments.

Jan 1, 1991