Search Documents

By Marcos C. Filgueiras, Thomas A. Post, Michael A. Giralico, Daniel M. Adams

The leaching of copper, gold, and nickel in tanks requires mixing. Minerals require oxygen, acid and/or base [NH3] to assist in the leaching process. Two basic types of tanks are used for this operation. They are either vertical tanks or closed horizontal tanks called autoclaves. This paper discusses mineral leaching, it's mixing requirements, and autoclaves.

Jan 1, 1999

By Colin Irwin, Adrian Naranjo-Castillo, Christopher Petta, Eric Zarobila

The Shoreline Consolidation Sewer is a CSO control project in Cleveland, Ohio that requires the installation of 5,000 feet of 72-inch inside diameter pipe using microtunneling methods. After award, the contractor submitted a value engineering proposal to eliminate two deep shafts and install the tunnel in two drives instead of four. In an example of successful collaboration, owner, contractor, and engineer worked together during the initial construction stages to modify the design and update the contract documents. This paper examines the importance of exible requirements in contract documents and a collaborative environment between all parties to successfully deliver a project.

Jun 23, 2024

By G. M. Swinkels

It is generally accepted, that oxygen is a necessary reagent for the flotation of galena with xanthate. Recent measurements have shown (1) that under plant conditions oxygen may be in a short supply to the extent that it limits the rate of flotation. Thus, it becomes important to define the exact role of oxygen and establish a model for the rational design and control of flotation separations, involving oxygen as a reagent. All theories or, the flotation of galena assign oxygen the role of an oxidant. However, they disagree on a number of questions: 1) Is the galena or the xanthate being oxidized? 2) Is a lead dixanthate or dixanthogen the actual collector? 3) Is the oxidation process in which oxygen participates of a chemical or an electrochemical nature? The last question arises from the observation (2) that an anodic bias as well as oxygen will make a galena surface hydrophobic in the presence of xanthate. Theories which are based an the premise that the influence of oxygen is of an electrochemical nature offer elegant models of galena flotation. However, full advantage has not been taken of available electrochemical techniques to discriminate between theories and this is the area towards which this research has been directed (3).

Jan 1, 1970

By Santhanam Sundaram

The potential for the utilization solar energy for the production of industrial process steer in mineral processing industries is discussed briefly. To advance the technical and economic feasibility of solar-thermal systems applications, U.S. Department of Energy has funded several projects. NL industries of Newberry Springs, California is one among them and has been chosen as a case study. The NL Industries solar system consists of 950 square meters of Del, single-axis, tracking, parabolic-trough, concentrating collectors. It was designee to produce a portion of the 420°. 530°k. steam utilized in a trying operation reduce the moisture content of hectorite ore from 10 percent to 4 percent. (Hectorite is an hydrous magnesium silicate which, when refined, is of significant commercial interest because of its applications in various chemical and food processes.) is estimated that implementation or this solar system could result an annual savings of 3.545 billion KJ ,3.360 billion BTUs), or the equivalent of 90 cubic meters (600 barrels) of oil and a net reduction of 1,860 kilograms (4100 pounds) of air pollutants annually. The technical, economic and institutional issues encountered in the course of this project are also discussed. Finally, the impact of the commercialization of solar energy applications in mineral processing industries is evaluated.

Jan 1, 1981

By William R. Taylor

The information I have concerning the early in situ uranium mining activities in Texas is "sketchy." Apparently, the first test was conducted between 1967 and 1971 in Gonzales County, north of Yorktown, at the Dueterstat Site, by, City Service. Other tests were run in Webb County at the Bruni Site, and in Live Oak County at the Burns and Clay-West Sites in the early 1970's. During this period the Texas Water Quality Board maintained a general surveillance of these tests. In mid-1974, Mr. Glen Davis walked into our Austin offices and requested a permit for Atlantic Richfield's first in situ uranium mine. This permit, issued in January, 1975, was for 3 acres of production, and was the first such permit issued in the United States. It formalized the regulation of in-situ uranium mining in Texas. The 4 years since then have been characterized by growth and change. Today there are 20 permits approved for approximately 2,000 production acres. These permits are issued to 8 companies at 13 sites in 6 counties. There are 7 additional permits being processed, or on the verge of being applied for. These will involve possibly another 2,000 production acres, 3 more companies in one more county.

Jan 1, 1979

By C. Y. Chen

In order to put an end to the uneven environmental standards and enforcement established by various coal mining States in the United States, the Congress passed and the President signed the Surface Mining Control and Reclamation Act (Public Law 95-87 or the Act) on August 3, 1977. Within one year after passage, the Secretary of the Interior was directed to promulgate permanent program regulations implementing Title V provisions of the Act. These regulations were to form the basis for State regulatory programs under the Act and to allow States to assume primary regulatory responsibility. In order to implement the underground mining provision of the Act, the Secretary is directed in section 516(a) of the Act to promulgate rules, but ones which take into consideration the distinct differences between surface coal mining and underground coal mining. The regulations developed by the Secretary and promulgated on March 13, 1979, with respect to subsidence control, included (1) a subsidence control plan as part of the permitting process, (2) substantive provisions establishing performance standards for subsidence control, and (3) provisions providing for the prohibition of mining under perennial streams, impoundments larger than 20 acre feet, and certain public facilities and urban areas.

Jan 1, 1985

Those who have had an occasion to apply geostatistics to the estimation of ore reserves are familiar with the conventional approaches of estimating average grade of quality values for arrays of regular grid squares or blocks. Further, the technology to perform geostatistical analysis and prediction for irregular two-dimensional areas has been available in a practical, readily useable form for some time. However, the generalization of this technology into three dimensions has been hampered by lack of a suitable geometrical characterization for realistic, three dimensional shapes and volumes. The extension of these estimation techniques into three dimensions has now been made possible by a successful integration of the volume modelling capabilities of 3D Component Modelling with proven 3D Geostatistical Techniques. The result is a powerful new technique for mineral ore reserves estimation in a practical, useable form. The technique allows direct geostatistical estimation of grade and quality values for precisely defined, irregular, realistic, geological, and mining shapes or volumes. This paper describes the two technologies, their integration and their application in practice to the estimation of mineral ore reserves. The paper closes with a discussion of the benefits provided by the new approach, in terms of accuracy, efficiency and practicality.

Jan 1, 1991

By J. H. Gasper

The overall success of steep slope (>20°) contour mining is dependent upon many factors. The major factor is the selection of the mining method that best suits the premining site conditions both environmentally and economically. These conditions can be divided into three major categories: 1) Geometric Conditions --machine limitations, slope stability restrictions, erosion capacity, among others; 2) Physical Conditions--material properties, rock strengths, diggability, driving surfaces, among others; 3) Chemical Conditions --acid/base relationships, blending or selective placement of overburden, among others. This paper incorporates these conditions through conceptually modeling compliance oriented contour mining methods; in particular Haulback methods, utilizing: 1) the Front-End Loader (FEL)/Truck; 2) Tractor Scrapers; and 3) Combined FEL-Truck/Scraper. Engineering analyses including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces), drainage requirements and many others can be performed after the geometric constraints dictated by in-situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views, but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By A. Casuge, D. Lee, J. A. Finch, C. C. Sui

The adsorption of copper and lead und their subsequent xanthate uptake were compared at pH 3.0, 6.0 and 9.2 on both fresh and oxidized sphalerite. The extent of adsorption and the rate of adsorption were strongly dependent on pH, with the highest adsorption of Cu and Pb being at pH 9.2. In the presence of both Cu and Pb, Cu adsorption was enhanced and Pb adsorption was suppressed. The adsorption kinetics of Cu and Pb were characterized by two- and three-stage adsorption processes, respectively. The exchange ratio of Cu to Zn was about one and that of Ph to Zn was greater than one and varied with pH. The uptake of xarlthate on "activated" sphalerite was dependent on pH. The rnaximum uptake was found to be at pH 6.0 for Cu-activated sphalerite artd at pH 9.2 for Pb-activated sphalerite. A measure of "activation strength" based on inetal ion adsorption and xanthate uptake was introduced. The activation strength of Cu to Pb was about one at acidic pH, but it was higher at neutral (pH -6) and alkaline (pH -3) conditions. The oxidation of sphalerite decreased Pb and, especially, Cu adsorption and decreased xanthate uptake.

Jan 1, 2000

By Eugene F. Casey, John G. Ruggiero

INTRODUCTION Construction of tunnels in urban areas, especially reclaimed areas, pose many problems. The Red Hook Intercepting Sewer Tunnel, Contract 1A is a portion of the Red Hook Water Pollution Control Project located along the Brooklyn waterfront in New York City. This contract required the construction of a 2620 meter long (8600 L.F.), 3 meter (10-foot) diameter soft ground tunnel, eight Tunnel Manholes, nine Regulator structures, four Diversion and Tidegate structures and 765 meters (2500 L.F.) of branch intercepting sewers of diameters between .30 meters (12 inches) and 1.8 meters (72 inches). The construction contract bid price was $62 million with a duration of three years. The tunnel route crosses over five sets of operational twin cast iron subway tubes with clearances ranging from 4.3 meters (14 feet) to as small as 0.35 meters (14 inches). The route of the tunnel traverses historically interesting areas which have been reclaimed over the last 200 years. This paper is a case history describing the contractor's methods utilized to successfully advance the work through the above problem areas. LOCATION The Red Hook Intercepting Sewer Tunnel is located in the Borough of Brooklyn of New York City. The route is

Jan 1, 1981

Traditional fine-grinding mills in mineral processing rely on the use of steel medium for particle size reduction. The IsaMill (a horizontal stirred mill with a 3, 000-L net chamber volume and a rated motor power of 1,120 kW) has successfully adopted a novel product-separator design, which has led to a major revision of medium use in fine grinding. The IsaMill separator has successfully operated with a wide variety of medium types, such as silica sands, river gravel, smelter slag, run-of-mine ore fractions and steel shots, with sizes ranging from 0.5 to 10 mm. Great flexibility in the IsaMill operations has been achieved for processing feed as coarse as 120 µm to a product as fine as 5 µm. This paper discusses the performance of two inert grinding media in the IsaMills that are used at Mount Isa Mines Ltd. for the processing of galena- and sphaleritebearing ores to below 10 µm. They are the copper reverberatory furnace slag (CRFS) and the heavy-medium plant rejects (HMPR). A methodology was also demonstrated for comparing the medium performance and for scaling up the IsaMills from a 1.5-L laboratory batch mill to a full-scale 3,000-L mill.

Jan 1, 2002

By Scott F. Andersen

Discussion to include location and description of the project from upper lake through powerhouse to lower lake, noting locations and size of shafts. Discuss evolution of shaft development concepts in conjunction with owner, contractor and CAL OSHA. Discuss elevator shaft equipment, T1 gate shaft, T2 surge shaft equipment, T3 surge shaft and the incline shaft equipment. Question and answer period.

Jan 1, 1981

By Joel K. Waterland

The Homes take Mining Company at Lead, South Dakota has a yearly production of 1,868,741 tons of ore produced from horizontal cut-and-fill stopes and timber cut-and-fill stopes. This production, in addition to the necessary development (drifts and raises), requires 5,168,271 feet of drilling annually. The rock for the most part consists of quartz; mica schist; and cummingtonite schist; and must be considered as relatively hard. Penetration rates average about 15 inches per minute using an operating air pressure of 100 psi. The rock is tough, rather than brittle, and dulling occurs quite rapidly. The average regrind period is approximately 19 feet per regrind using a 1-7/16 inch carbide bit. At the present time, all drilling is accomplished with 2-5/8 inch bore airleg mounted drills, and 2-3/4 inch and 3-inch diameter bore -stopers (raising only). These machines are all direct striking, with 4-1/4 inch chucks. 7/8-inch hexagonal carbon drill steel with forged collars are used in conjunction with 1-7/16 inch multi-use, threaded, carbide bits. 62,793 rods, and 16,234 bits are used to maintain the yearly production. The number of rods noted are the rods that were sent: underground, both new and reconditioned.

Jan 1, 1963

By A. Bruynesteyn

Many papers 'have been publihed on the role of the bacterium.Thiobacillus ferrooxidans in the oxidation of reduced sulfur compounds, and years of research have established the following environmental factors, which influence biological oxidation. 1. Oxygen is required for the oxidation of reduced sulfur compounds to the sulfate form. Sufficient oxygen. is available from the air, consequently, it is of importance to get the air to the bacteria. 2. The bacteria are active in the pH range 1.4 3.5. Maximum activity occurs at pH 2..0 - 2.8. 3. -In order to allow the bacterial populations to expand, certain essential nutrients must be available. Nitrogen has to be supplied for the production of body protein, and ammonia is the source most readily accepted by the bacteria. Carbon dioxide is the only utilizable source of carbon and the small amounts available in air are the primary source of this element. Small amounts of phosphate, manganese,, potassium,. calcium. and magnesium are also required. These trace minerals are available from the water and host rock in sufficient quantities. 4. Water is required as a carrier for the oxygen carbon dioxide and other nutrients, as-well as a solvent for the metallic sulfates produced. The bacteria are motile and the water allows the bacterial populations to spread:: bacterial activity ceases if the equilibrium relative humidity drops below 100%. 5.-optimum bacterial activity occurs at temperatures of 34 - 35°.C (93 -.95° F). All activity ceases above 45° C. At lower temperatures, activity its dramatically decreased, but there is still a significant amount at 10 - 11° C.- Thiobacillus ferruoxidans has been isolated from a mine with a year round temperature of 3° C. 6. Unpublished results from our laboratory show that biological leach ore oxidation takes place during the rest periods at the same rate as during the wet leaching periods providing there is a film of moisture remaining around the particles. Optimum conditions can be readily achieved in the laboratory, but application of our laboratory knowledge to commercial leaching dumps is riot as simple. Attempts to achieve improved environmental conditions for the bacteria in leaching dumps would require substantial capital investment and careful planning of leaching operations. This paper

Jan 1, 1972

By David Caiden, Petros Fortsakis, Alan Hodgkinson

"1. INTRODUCTIONDo contractual practices affect project outcome? Can better contractual practices improve the likelihood of project success? The consensus amongst experts is that better contractual practices really do improve project outcomes. With this in mind the members of the International Tunnelling Association (ITA) Working Group 3 on Contractual Practices (WG3) pooled their collective knowledge to publish in 2011 the document entitled The ITA Contractual Framework Checklist for Subsurface Construction Contracts (ITA Working Group 3, 2011). Written for projects involving significant subsurface works, e.g. tunnels and caverns, the ITA Framework Checklist explains the major contractual issues that must be considered to ensure a successful project. Its goal is not to specify how each issue should be resolved, but rather to highlight the issues and give recommendations on how they should be addressed. The Checklist is compatible with, and provides guidance for reviewing, standard contracts such as FIDIC and NEC. One of the authors is a co-author of the Checklist and has contributed to previous papers describing the Checklist and its applicability to hydropower projects (Hodgkinson & Wilson 2014, Hodgkinson & Wilson 2015). The Checklist identifies a series of issues that should be contractually defined, which can be summarized as follows: •,Methods for dealing with geotechnical uncertainties should be defined in the contract •,There should be an appropriate level of geotechnical/geological investigation •,Sufficient mobilization periods should be allowed •,Sufficient time should be allowed for testing and commissioning •,Procedures for timely dispute resolution should clearly defined •,Quality and performance requirements should be clearly defined and measurable •,Provision should exist for cost consequences of unforeseen circumstances •,Dispute resolution processes should be clearly defined •,Payment processes should be fair and clearly defined •,Risk should be clearly allocated and parties should be able to bear the risks they carry •,There should be a mechanism for adjusting payments according to conditions •,The risk management approach should be clearly defined •,Admeasurement or unit price approaches are recommended •,The responsibilities of each party must be clearly defined •,The consequences of non-performance should be clearly defined •,The construction programme (schedule) should be realistic."

Jan 1, 2016

By James Matlock

The announcement of a minable reserve of 13.6 Mt (16 million tons) averaging 0.9 g/t (0.027 oz per ton) Au and 2.4 g/t (0.71 oz per ton) Ag for the open pit-heap leach reserve at Red Mountain No. 3 in Ouray County, Colorado, by Cornucopia Resources in November 1985 brings another open pit-heap leach precious metal ore body to the production stage. With about 8.2 Mt (9 million tons) of waste and metallurgical studies showing acceptable recovery rates, low reagent consumption, and good final percentage recovery, Red Mountain is a discovery that will add to the precious metal inventory of the US. Frank Baumgaruler of Denver, CO, recognized the precious metal potential in Red Mountain No. 3 and acquired all of the old claims. James Matlock conducted a field reconnaissance over Red Mountain No. 3 independently of the Baumgartner activities and recognized epithermal alteration and mineralization in the Tertiary volcanics. He recommended acquisition of the ground and was able to obtain rights and drill six core holes for Amoco in 1982. Amoco drilled a further nine core holes in 1983, but then dropped the property. Cyrano Resources examined the data and through its consulting geologist, V.F. Hollister, acquired the rights dropped by Amoco. In 1984 Cyrano began further drilling of the ore zone demonstrated by Amoco but they were then acquired by Cornucopia Resources. Cornucopia completed development of the property and commenced the permitting process in 1986. The property was recognized as a disseminated gold deposit by both Baumgartner and Matlock, and both deserve credit for properly evaluating mineralized outcrop in the Tertiary volcanics. However, Cornucopia recognized the profit potential in the heap leach exploitation of the ores and de- serves credit for completion of premine feasibility studies. The discovery is clearly a geological one, but the premine engineering studies were essential to the conversion of the prospect to a commercial mining enterprise. The deposit lies on the circular bounding fault of the Silverton caldera. Two reprints follow that help understand the geologic setting of the ore controls.

Jan 1, 1990

By Jurij Karlovšek, Marko Žibert, Scott Keniston

"SUMMARY The importance of information management was recognised in surface construction industry decades ago, and has increasingly being recognised through formal process and laws. Around the world, these laws and codes of practice are currently being drafted and enacted, to reflect the development of software tools and corresponding increasing adoption by industry. This paper deals with specifics of implementing information modelling in tunnelling business utilising BIM (Building Information Modelling) technology developed for buildings as well as similar technology developed for mining industry. Although BIM is recognized initially as a 3D digital representation of physical and functional characteristics of a facility, the real benefits come when complex capability through construction sequencing and even detailed programming (4D) and cost capabilities (5D) are included. INFORMATION MODELLING The Architecture, Engineering and Construction (AEC) industry requires the production of design and construction information, which involves the input from several teams. The tasks allocated to each team need to be carried out in a particular order and coordinated in order to benefit all those involved and the project itself; this is known as “collaborative working”. To ensure the quality, and guarantee that information can be used without change or interpretation, working processes and standards needs to be agreed upon or else it will hinder collaboration and have a negative impact on project delivery. Case studies show that the additional capital delivery costs due to uncoordinated, inaccurate and ambiguous information amounts to 20-25%. The solution to overcome these problems and improve collaborative working in a project is the adoption of BIM. It is a modern approach to the design, documentation, delivery, and life cycle management through the use of project information databases coupled with object-based parametric modelling. BIM requires traditional practices shifting from simple drafting to using 3D native models for building design environment. Additionally, it requires that models are equipped with information that has been traditionally decoupled in a text or other kinds of documents. The goal is not in creating a 3D graphic representation of design intent; rather, it is a comprehensive information management tool based on the simulation of design and construction build around a central repository."

Jan 1, 2016

By E. B. Kroeger

One of the problems encountered when constructing a roadway is the planned route often needs to cross soils that are soft and highly compressible. An approach to dealing with soft and compressible soils is to construct the fill from lightweight materials, thereby reducing the stresses on underlying soils. Most lightweight fills have approximately the same cost, so the most important consideration when choosing a lightweight fill is that the material properties of the lightweight fill match the conditions existing at the site. Expanded polystyrene (EPS) has been used as a lightweight fill material for more than 30 years. The EPS used for road fills is typically in the range of 0.5 to 2 lb/ft3, and has a compressive strength of in the range of 10 to 30 lb/in2. If a higher strength material is needed, then the material density is increased, which also adds to the cost of the material. Another type of lightweight fill material that is commonly being used is lightweight aggregate (LWA). LWA can be created by passing slate or shale through a rotary kiln or reheating coal fly ash with other materials to form pellets or aggregate. Several companies throughout the U.S market these materials under a variety of names. LWA can have a unit weight from 45-80 lb/ft3. For sites where trucking granular fill does not pose a problem, this material may be an alternative to EPS. One of the drawbacks to using LWA is the availability of the material. Only a few companies are manufacturing LWA, so it may not be available or may be cost prohibitive in certain areas of the country. Lightweight flyash blocks have been produced which may fill the gap in unit weight between the EPS and LWA. Blocks have been produced with a unit weight as low as 30 lb/ft3. They are relatively inexpensive, easy to handle, and have a moderate compressive strength. Although the unit weight is dramatically higher than EPS, the strength is also higher. If lateral stabilization of the fill is a problem, then geofabrics or grids can be incorporated into the design to add lateral strength.

Jan 1, 2003

By Steven J. Kirk

In the past decade, many hardrock surface miners have revegetated dumps and tailings ponds to allow those waste disposal areas to blend more easily with the surrounding landscapes. Efforts have also been made to more creatively use the flat land resulting from the disposal of overburden and tailings. However, the mines which serve the best post-mining land uses are those that have been preplanned to incorporate such end uses. To more fully explore such a philosophy, interdisciplinary team from The University of Arizona conducted a study during 1974 and 1975 of six open pit copper mines in the Santa Cruz River Basin south of Tucson, Arizona for the purpose of investigating both interim and end-use possibilities for mine waste disposal areas. Among other reasons for the study, it was felt that alternatives for such waste areas would be more socially acceptable than barren dumps or tailings ponds. The team, known as the Mines Project Group, consisted of architects, engineers, and hydrologists. As it would have been economically infeasible to move the existing waste rock dumps or tailings ponds, preplanning was limited to the disposal of waste generated after the inception of the project. To better present their concepts, architecture professors Kenneth Clark and Fred Matter constructed a large-scale cardboard relief model of the mines and the surrounding Santa Cruz River Valley (1). The model was built at a scale of 1:12 000 (1 in = 1000 ft) with 30.48 m (100 ft) contour intervals and covered an area of 40.23 km by 32.18 km (25 miles by 20 miles) in scaled area. The mines being studied were cut into the model, but the proposed waste dumps and tailings ponds were built separately so different disposal configurations could be evaluated.

Jan 1, 1980

By M. A. Kaufman

In this paper I will attempt to present an up to date review of the type of exploration' that has previously been carried out in Alaska, discuss some of the more significant past producers and recent discoveries, and suggest some approaches to future exploration. Hopefully this information may be of some use to those parties tempting to evaluate Alaska's non ferrous, non placer, metal potential or contemplating initiation of exploration in the state. II. SUMMARY AND CONCLUSIONS Past production of non ferrous metals from lode deposits in Alaska has been meager considering the size of the state. Since there have been no major lode mines operative in Alaska since World War II, and since logistical conditions vary throughout the state, it is not possible to generalize with respect to mining costs in Alaska as compared to those in other areas. There seems to be little question, however, that a major deposit situated in a reasonably favorable location' could be profitably operating at present. Host of the known metal prospects in Alaska were discovered by early gold prospectors prior to World War I. From World War I through World War II exploration consisted chiefly of surface prospecting by prospectors on a diminished scale, as compared to the early gold rush days, drilling of some prospects by the U.S.B.M,, and occasional mine or prospect evaluations by mining companies. From the end of World War II to the present time, there has been a generally steady increase in exploration by mining companies consisting chiefly of prospect and district evaluations, large scale aerial reconnaissance programs in search of color anomalies, and regional drainage geochemical surveys. The post World War II increase in mining company exploration has not been matched by an increase in conventional surface prospecting.

Jan 1, 1972