Search Documents

By S. K. Singh

To meet increasing demand of coal, underground mining is largely being replaced by the exploitation at deeper horizons and with greater complexities. The exploitation-proposition may be below not-to-be-disturbed surface properties or below water-bodies, posing a constant threat of inundation. Also, the mounting pressures to limit the adverse impacts on the environment bring the extraction-undertaking to face more challenges. An understanding of subsidence-mechanism and a rational quantification of subsidence parameters is a requisite herein. This paper presents such pragmatic quantification, validated at mine-sites in India. In comparison, better productivity, conservation and safety is ensured in this approach.

Jan 1, 1999

By A. J. Martin, M. J. Peoples, D. J. Adams, A. Opara

"The weathering of coal mine waste rock releases iron, calcium, sulfate and associated trace elements like selenium (Se). Nitrogen species are also found in association with coal-mining drainages mainly due to the leaching of residual blasting compounds. Elevated concentrations of Se are a ubiquitous occurrence in coal-mining environments in British Columbia. A major concern with waterborne Se in British Columbia is the potential for its bioaccumulation in aquatic food chains.Treatment to remove Se from coal-mining waste waters has proven to be challenging for conventional water-treatment technologies. Compounding this challenge, many streams are characterized by high flows and low selenium concentrations. Conventional membrane and ion exchange treatments produce concentrated brine streams that are difficult to treat or require disposal. Conventional biotreatment systems use excess nutrients to provide the required electrons to compensate for inefficient and variable electron availability, as well as to adjust reactor chemistry.This paper's electro-biochemical reactor (EBR) technology provides a controllable and consistent supply of useable electrons to the microbes directly at a low voltage potential (1-3 V) and low current. In this manner, the EBR technology overcomes the shortcomings found in conventional systems, as it reduces the required nutrient addition and provides a more controllable, efficient, economical and robust biotreatment system. Additionally, the EBR process does not produce excess solids or biomass; therefore, solids management post-treatment is not required.Laboratory EBR bench-scale and on-site pilot-scale systems were used to treat five British Columbia coal-mine waste waters; influent Se concentrations ranged from 35 µg/L to 531 µg/L. Se treatment targets for the tested waters ranged from 5 to 10 µg/L. Mean Se concentrations in EBR effluents ranged from 0.5 µg/L to 1.4 µg/L, while reducing sulfate concentrations. The test data demonstrate that the EBR technology is an effective Se removal option for British Columbia’s coal-mining waste waters.IntroductionSelenium in Mining. Selenium (Se) is a naturally occurring trace element, which is an essential nutrient in small amounts (Thompson and Robinson, 1980; Brown and Arthur, 2001). However, it is also toxic to aquatic life, birds, and humans at very low concentrations. A major concern with waterborne Se is the potential for its bioaccumulation in aquatic food chains, resulting in acute and/or chronic toxicity to fish, water birds and amphibians (Besser et al., 1996; Conley et al., 2009)."

Jan 1, 2015

By Donald W. Foss

The Shiloh Church deposit is a very significant molybdenum occurrence in an ususual, perhaps unique, geologic environment. Work done to date indicate that several million tons of "ore" may be present, occurring as a matrix in limestone and dolomite breccias. Mineralized rocks cored to date are at or near the surface and the deeper resource potential has not been tested. The prospect is located in Polk County, north- western Georgia (Fig. 1). The "ore zone" was outlined by North American Exploration, Inc. (NAE) using geochemical prospecting techniques. Extensive geological work, including core drilling, has been conducted on the properties, together with geochemical and geophysical surveys. The geology, geochemistry and geophysics of the prospect are discussed. It is hoped that these data can be used to formulate exploration programs in similar terranes located elsewhere in the eastern U.S.A.

Jan 1, 1983

By Jean-Michel Rendu

That you are giving the Daniel C. Jackling award to me is a great personal honor. But more significantly, it is a recognition that geostatistics has come of age. And since I am considered by many as belonging to an older generation of geostatisticians, I thought that it would be fitting that I reflect on where geostatistics came from and where it might be going. First, though, let me propose a definition of geostatistics. Etymologically, paraphrasing Webster's definitions of "geo" and "statistics," it is "a branch of mathematics dealing with the collection, analysis, interpretation and presentation of masses of numerical data taken from the earth." This definition is most appropriate in the context of mining geostatistics. It includes both classical and spatial statistics. It emphasizes the earth aspect, or the analysis of geologic features. And it should remind the practitioner that geologic input is a critical part of all geostatistical applications. In the 1910s, statistical methods were already used to analyze geological data. However, the origin of geostatistics, as we know it today, is best set in the late 1940s, when H.S. Sichel recognized the lognormal distribution of sample values in the South African gold mines. In 1951, Daniel Krige observed that "it can be expected that the gold values in a whole mine will be subject to a larger relative variation than those in a portion of the mine." In other words, samples taken close to each other are more likely to have similar values than if taken farther apart. This observation is the foundation on which spatial statistics, which characterizes values defined in a multidimensional space, is built. However, the 1950s were marked by studies based on classical, as opposed to spatial, statistics. It was only in the 1960s that the need was recognized to model the similarity between sample values as a function of the distance between samples and that the semivariogram was defined. A theoretical framework was developed by Matheron that supplied an elegant mathematical explanation to the empirical observations made by Krige. Matheron coined the term "kriging" in recognition of Krige's pioneering work on the geostatistical evaluation of mineral deposits. As soon as this theoretical framework was developed, it was possible to bring geostatistics to the academic world. The "Centre de Geostatistiques" was founded in Fontainebleau. Numerous students were trained there, disciples eager not only to improve the theory and develop more sophisticated mathematical tools, but also to spread the new faith throughout the world. Expansion of geostatistics exploded in the 1970s, arguably the most fertile decade if it is judged by the frequency of theoretical breakthroughs, the number of original publica-

Jan 1, 1995

By Ting Ren, Lihai Tan, Alex Remennikov, Xiaohan Yang, Xueqiu He

"Due to recent coal bursts in Australian coalmines, research of coal bursts has attracted intensive interest from mining researchers and engineers worldwide. Previous research has shown that the sudden drop of fractal dimension may be a precursor of catastrophic failure of rock. This paper examines the fractal characteristics of temporal-spatial distribution of acoustic emission signals released during the compression loading process of coal. This research suggests the possibility of coal burst forecasting based on acoustic emission data. The concept and calculation equation of fractal dimension is introduced in this paper. Additionally, uniaxial compression experiments of Australian coal samples are conducted, and the acoustic emission waveform and 3D location are recorded simultaneously by eight sensors Express-8 AE monitoring equipment in the loading process. The experimental results indicate that the continued slowdown of fractal dimension in time sequence can be used as a precursory signal of coal sample brittle failure. The fractal dimension of the spatial distribution of acoustic emission events decreases with the evolution of coal fracturing.INTRODUCTIONCoal bursts refer to the catastrophic failure of overstressed coal subject to the dynamic and static loads. In recent years, coal bursts have occurred in major coal mining countries and this phenomenon has attracted the research interests of international mining and geotechnical scholars. A total of five coal burst accidents happened in Australian coalmines since 2014. On October 20, 2018, a coal burst occurred at Longyun Coalmine in China’s Shandong province, which led to 21 fatalities. Unfortunately, even after decades of research, it seems neither more accurate forecasting methods nor comprehensive controlling measures put forward by researchers have solved the problems posed by coal bursts.As an instantons energy releasing process, coal bursts are always associated with energy dissipation in the forms of acoustic emission, micro seismicity, and electromagnetic radiation (Yamada, Masuda, and Mizutani, 1989). It is believed by many researchers that the frequency–magnitude relationship of micro seismicity induced by rock failure satisfies Gutenberg-Richer relationship as well (Feng et al., 2017). Hence, based on the principal and theory of earthquake source locating, micro-seismicity monitoring equipment has been adopted in many coalmines to locate seismic event origins associated with coal and rock failure in an attempt to better forecast coal and rock bursts. Although many parameters such as b value (parameter of Gutenberg and Richter’s law) (Lu et al., 2015) have been adopted as indicators of risk, the forecasting of coal bursts is still of low accuracy. The same is true with earthquake prediction, as it remains as a worldwide problem even after decades of research and practice. Acoustic emission (AE) methods are now widely adopted to detect rock failure processes under an applied stress for application predicting the abrupt failure of rock in the laboratory (Li et al., 2017). Previous studies have found that significant overlap exists between research regarding AE and micro seismicity with respect to generation process (both are concerned with the generation and propagation of elastic wave) and event origin location, as geophysical signals of both are same (Lockner, 1993). That is, the frequency–magnitude relationship and early-warning indicators found by AE research in the laboratory have a potential applicability to in-field micro seismic monitoring of coal bursts. Through experimental study, Feng and Seto found that the temporal distribution of acoustic emission counts of rock have distinct fractal structures during load-increase processes (Feng and Seto, 1999). Landis and Lucie found good correlation between fracture energy and AE energy during testing of mortar specimens as well (Landis and Lucie, 2002). Based on preliminary experimental study, many schol"

Jan 1, 2019

By J. M. Elder, W. S. Kow

Challenges to new heavy mineral deposit developments are presented. These include land use issues, particle fineness, declining grades, and particle coating, amongst others. Industry responses to these are presented as possible solutions.

Jan 1, 2005

When it comes to safety in the mining and extractive industries, success is literally a matter of life and death. Anything short of perfection is not acceptable. In recent years, the mining industry in the United States has made tremendous strides in terms of health and safety for its workers. Part of that success has come with an increased focus on the issues of safety, an intense examination of procedures, liberal sharing of best practices and a focus on the synergy between safety, reliability and environment. During his closing keynote address of the Safety Management & System Reliability Conference in Minneapolis, MN on Nov. 15, Joe Driscoll, vice president of Great Basin Gold, showed a calendar from the coal fields in Pennsylvania from the early 1900s. The calendar marked the number of mine-related deaths each month. Some months, the number was as high as 50. It was an illustration of how far things have come, but there is still much more work to be done.

Jan 1, 2013

By R. E. Murray

"It is a gloomy moment in the history of our country. Not in the lifetime of most men has there been so much grave and deep apprehension; never has the future seemed so incalculable as at this time. The domestic economic situation is in chaos. Our dollar is weak throughout the world. Prices are so high as to be utterly impossible. The political cauldron seethes and bubbles with uncertainty. Russia hangs, as usual, like a cloud, dark and silent, upon the horizon. It is a solemn moment. Of our troubles, no man can see the end." By now you, no doubt, are asking, 'Where did Murray get this bit of philosophy?' Well, I obtained it from an editorial entitled. "The Worst of Times", which was published in the Harper's Magazine in 1847. That's right, 1847! The parallelism between the situation in our country at this time and in 1847 is un- canny. But wait, there is one major exception the size of government. To my knowledge, the citizens of 1847 were not stifled by the extreme governmental excesses that we are experiencing today.

Jan 1, 1980

By Craig Hartley

? A helper stands beside a continuous miner as the operator is at the controls. The operator means to push the stop button but hits the drum rotation start button by mistake. The drum begins to turn and the bits catch the helper's clothing. He is thrown violently to the ground and suffers multiple contusions. ? A farmer's wife helplessly watches her husband drawn into the claws of farm machinery while she frantically and unsucessfully searches for the control to stop the machine. ? A mechanic on the night shift replaces plugs in the lubrication systems of all three engines of an airliner following routine maintenance. In doing so', he fails to notice that "0" ring seals have not been mounted on the plugs. A few hours later, as the fully loaded airliner is cruising high over the ocean, oil pressure on one engine drops precipitously. The pilots quickly shut down the engine and turn for home. Almost immediately, the two remaining engines lose their oil and fail.

Jan 1, 1983

By W. R. Dengler

Dynatec Mining Limited contracted to sink a lS00 metre (4960 ft.) concrete lined shaft for Falconbridge Nickel Mines in Sudbury, Ontario, Canada. The shaft is 6.3 metres (20.S ft.) in diameter inside the concrete lining and is equipped with steel furnishings. Dynatec used the owner supplied 4.6 metre (l5 ft.) diameter double-drum hoist to sink the shaft with 12.S tonne buckets for muck removal and 4 cubic metre concrete buckets for concrete placement. One of the unique features of the shaft sinking operation is the use of a four-boom electric hydraulic drill jumbo permanently mounted in the shaft sinking stage. This paper will describe the performance obtained with the electric hydraulic drilling equipment and the high capacity muck removal and concreting equipment.

Jan 1, 1992

By S. Chatterjee, A. K. Gorai, Sahendra Ram, Kapil Kumar, J. Anil

Extraction of underground coal or mineral by the caving methods leads to surface deformations and the accurate measurement of this deformation is becoming a demanding task. Thus, the study demonstrates a Persistent Scatterer Interferometric Synthetic Aperture Radar (PS-InSAR) technique for surface subsidence measurement. The method was applied to measure the subsidence level over three mechanized depillaring panels with caving at GDK-11 Incline mine, India. The study was conducted using C-band data of Sentinel 1A/B sensors, which captured the data in the descending path from October 25, 2017 to March 07, 2020. The deformation level was measured based on the identified PS points in the specified region. In this case, 12 zones were identified (4 for each panel), based on the observation of permanent scatterer (PS) points. The maximum subsidence level and deformation rate range in 12 zones are −43.12 to −65 mm and −73.8 to 100 mm/year, respectively. The deformation level obtained through the PS-InSAR technique showed a good agreement with those of the field measurement. Thus, the PS-InSAR technique can detect and monitor the subsidence level over the goaved-out panel(s) of an underground mine using C-band SAR data of the Sentinal-1A/B sensor.

Mar 14, 2023

The use of coal as a fuel causes air, pollution in; a number of different forms, and in nearly all stages of its, handling, preparation, storage, use and-disposal of its residue. First let us consider the handling of coal. As shipped, particularly to large utilities, it is run-of-mine bituminous made up of large chunks as well as pulverized particles. Because it 'is in an open car or barge, it is subject to the action o winds and the small particles may be blown around adding to the-particulate load in the atmosphere. Mien un¬loaded from the barge or car, there is again an opportunity for the wind to blow the fine particles around. All of us I am sure have seen a barge at the dock of a utility plant being unloaded by a clamshell bucket. This, after grabbing its load from the barge, lifts it some 60 or 70 feet and, then drops it on a conveyor, which carries the coal to a storage area.

Jan 1, 1964

By Warder A. Shaver

INTRODUCTION Mine No. 95 of the Consolidation Coal Co., a divi¬sion of Continental Oil Co., is located in Shinnston, WV. Mine No. 95 was opened in January 1967 and has been operating continuously since that time. The mine has 544 hourly and salaried employees. In 1974 this mine was the largest coal producer in West Virginia. Opera¬tions include two longwall sections and eight Marietta Borer continuous miners. Originally there were also two Jeffrey Heliminer continuous miners, but use of these was discontinued in June 1978. Production averages 12 727 t/d (14,000 stpd). Two portals now service the mine with a third portal proposed for 1978. GEOLOGY Mining takes place in the Pittsburgh coal seam which dips 0.04 rad (21h°) northwest. The working seam is steam coal with an average height of 2.2 m (86 in.). Immediately above the seam, the overburden is com¬posed of 6.1 m (20 ft) of shales followed by 6.1 m (20 ft) of weak sandstone and 51.8 (170 ft) of shaley limestone. The shale weathers when exposed to mois¬ture. Surface water has been a problem due to a fire¬clay floor which turns to paste when mixed with water. GENERAL DESCRIPTION The present mining plan for Consol's No. 95 mine has a proposed life of 35 to 40 years. One set of main headings has been driven in the north direction and one set in a western direction. These are the areas in which the majority of the virgin coal lies. The panels are driven off of the mains at 2134 to 3048-m (7,000 to 10,000-ft) intervals. The continuous mining sections are set up 133 x 610 m (600 x 2000 ft). Longwall sections are 259 x 1220 m (850 x 7000 ft). All of these mining sections are retreating uphill. Development is with continuous miners. A Marietta Borer miner is used for the main development work. These miners cut 4.1 m (13 ft 6 in.) wide and 2.1 m (7 ft) high, leaving an arch cut. Along with the arch, a 152.4-mm (6-in.) thick layer of roof coal is left in place to protect the roof from weathering. The combi¬nation of the self-supporting arch and the roof coal al¬lows the entries to be driven 30.5 m (100 ft) without bolting. Full bolting, however, is carried outby the last open crosscut. This bolting is done on 1.5 x 1.5-m (5 x 5-ft) centers using 1.5-m (5-ft) long roof bolts with tandem anchors and 152.4-mm (6-in.) steel washer plates. When needed, crib blocks with a 50.4-mm (2-in.) drill hole are used as supplemental supports. Three-hole steel channel with the ends curved down¬ward to conform to the borer arch may also be used. In the mining sections, a 14 BU loader is used be¬hind the Marietta miner to load two Torkar shuttle cars. These haul to Long-Airdox feeder breakers which load onto a 1.07-m (42-in.) wide conveyor belt. With the exception of the shuttle cars, which use 275-V d-c power, the face equipment operates on 550-V a-c power. The main power line is 7200 V ac. The same loading and hauling equipment is used with the Marietta Borer miner for driving both panel and development entries. In the retreat sections, the same equipment with the exception of the miner is utilized. Because of the advantage of a variable cutting hight, Jeffrey Heliminer ripper-type continuous miners were employed in these retreat sections. For longwall mining the first unit uses an Eickoff EDW 300-L double-drum ranging shearer. Drum di¬ameter is 1.69 m (66 in.) with a drum rotation speed of 45 rpm. The drum is equipped with 48 Carmet 34-L-1 bits. The 300-kW (400-hp) motor operates on 1000 V. Tramming of the shearer head is done through a hydraulically driven 26-mm wide chain. Maximum cutting speed is 7.93 m/min (26 fpm), and maximum tram speed is 12.8 m/min (42 fpm) with an average cutting speed of 3.66 m/min (12 fpm). Web cutting depth is 762 mm (30 in.) and the cutting height is 2.13 m (7 ft). The conveyor width is 686 mm (27 in.). It uses a single chain, 26 mm thick, with flights on 0.91-m (3-ft) spacing. The face conveyor speed is 64.3 m/min (211 fpm) when driven by two 112-kW (150-hp) 1000-V Louis Allis motors through torque convertors. The roof support used is Gullick Dobson chocks [6-legged 77.3 t (85 st) per leg, 463.6 t (510 st) total capacity] with double-acting leg jacks. The hydraulic pressure for the legs is 13.8 MPa (2000 psi), and the hydraulic pressure for rams is 6.8 MPa (1000 psi). The yield valves are set at 57.8 MPa (8500 psi). Each chock weighs 4.09 t (4.5 st). The stage loader is an Eickoff drive, with a 68-kW (90-hp), (00-V Reliance motor. A 26-mm thick single strand chain with flights on 0.6-m (2-ft) centers runs at 75.89 m/min (249 fpm). The stage loader is self-advancing and is connected to the belt tail piece with a special fifth wheel attachment so that the stage loader can advance and guide the tail piece. The hydraulic pressure for the roof support is supplied by two 45-kW (60-hp) Reliance motors op¬erating on 699 V, with 1.26 L/s (20 gpm) constant volume Gullick hydraulic pumps. Each pump services alternate chocks, with the two pressure lines connected at the tailgate by 25.4-mm (1-in.) hydraulic hoses, rated at 27.21 MPa (4000 psi). The 6.8 MPa (1000 psi) pressure rams advance is supplied by a 45-kW (60-hp), 600-V Reliance motor and a 1.26-L/s (20-gpm) con¬stant volume Gullick pump. Return lines are 35.5-mm (1.4-in.) diam hydraulic hoses with rated capacity of 27.21 MPa (4000 psi). The fluid used in the hydraulic system consists of 95% water and 5% Hy-chock fire resistant water soluble oil. Water is stored and mixed in a 6096-L (2000-gal) track-mounted tank and goes to a 655-L (180-gal) reservoir at the pump. The belt conveyor structure is 1.07 m (42 in.) wide with 0.47 rad (27°) idlers, bottom stands located on 3.05-m (10-ft) centers, top stands on 1.5-m (5-ft) centers, and is supported on a 19-mm (3/4-in.) diam

Jan 1, 1982

By Dimitrios Litsas, Michael Kavvadas, Panagiotis Sitarenios

"The paper discusses the results of 3D finite element analyses to investigate the effect of face support pressure and soil permeability on face stability conditions in EPB tunnelling. Two main types of face behavior are identified: Undrained conditions ahead of the tunnel face, typically occurring in soils with permeability less than about k=5·10-7m/s, are shown to be favourable for face stability; analyses show that an applied face pressure comparable with the initial hydrostatic pore pressure is sufficient for adequate face stability, even for soils of relatively low strength. Drained or partially conditions, typically occurring in soils with permeability higher than about k=5·10-6m/s, show that face stability is strongly dependent on the horizontal effective stress of the muck in the excavation chamber; the presence of even a small effective stress in the muck is very beneficial for face stability conditions and can be a possible explanation of successful EPB tunnelling through relatively permeable soils. INTRODUCTION Face stability is probably the most important aspect in urban tunnelling. Usually, Earth Pressure Balance (EPB) machines are utilized, to ensure that a reasonable amount of face pressure is exerted on the advancing excavation face, reducing ground loss and preventing potential instability of the face core, thus controlling the amount of disturbance caused by tunnel excavation to surface structures. However, the ideal amount of face pressure depends on several factors (ground and groundwater conditions, tunnel size and depth, muck conditioning, etc.) which are difficult to include in analytical calculations. For many years, conventional empirical or analytical methods (e.g. Anagnostou & Kovari 1996) were the only available tools for quantifying face stability and selecting the required face pressure. In the last few years, however, numerical analyses have gained power over conventional methods, allowing more accurate designs and providing useful information about the anticipated ground deformations due to tunnelling. Numerical analyses have also been used in assessing safety against face instability using face extrusion (horizontal face displacement) calculations (e.g. Prountzopoulos 2012)."

Jan 1, 2016

By William Crowe Kellogg

By now the term AFMAG has been fairly well introduced to the mining industry. Several papers have been presented and published concerning AFMAG (references 1 and 2). However, the term AFMAG remains rather new to the industry, and the exact place which AFMAG occupies in the minerals exploration field is still somewhat uncertain in the minds of many who may have use for this new and interesting method of electromagnetic exploration for conductive minerals. It is the purpose of this paper to again review the basic theory of the AFMAG system, to describe and - illustrate the equipment and data presentation as used in aerial surveying, and to provide some idea of the cost and nature of airborne AFMAG surveys. This paper is primarily of a general descriptive nature and presents AFMAG theory in a schematic rather than mathematical form; emphasis is placed on the equipment, the present method of data presentation and survey operations, since it is believed that such, information will now generally best serve to inform the mining industry of the characteristics of the AFMAG system.

Jan 1, 1960

By Malcolm D. Flavel

Much has been said and written about the world's, and particularly the united states of America's, energy crisis. The relative changes between cost components of production have altered because the days of cheap energy have now gone. Decisions that made capital investment reduction attractive to treat large tonnage lower grade ore bodies appear to be no longer valid because average energy costs for comminution that were less than 1 cent per kilowatt hour in 1972, are now more than 3 cents and will shortly become 6 cents according to some projections. Increased capital investment to improve processing energy efficiencies are certainly going to be pursued. Energy today is the largest cost component in the average mineral production facility. It takes more than 12000 kilowatt hours to produce one ton of finished steel and more than 60000 kilowatt hours for each ton of copper and aluminum.

Jan 1, 1980

By Hugh R. Rhys

The question of the desirability of recovering cullet from MSW in order to recycle it into the manufacturing of glass containers remains a controversial one. The main factors appear to be: 1. The position of the Glass Container Manufacturers Institute (GCMI), as the trade association for most container manufacturers, is that post-consumer cullet is a vital source of raw material. Present requirements are for: a) Flint cullet b) Non-flint cullet of known mix proportions c) Mixed unsorted cullet of known mix propertions c) Mixed or non-flint cullet of unknown mix proportions. A market balance for these products exists, and this might somewhat limit the outlets for (b), (c) and (d), or severely limit the outlet for (d) alone. 2. The color specifications are rather strict. With cullet admixtures of 20% of the melt or more, and the use of decolorisers in a flint furnace discouraged because their action is reducing in a process which requires an oxidising environment, color contamination in a flint furnace is serious.. For amber and green furnaces (reducing) it is less serious, but in order that the quantity of decolorisers may be controlled, the color balance (as a measure of the Fe and Cr content) of the admixtured cullet should be known. 3. Why not simply color analyze, either by a continuous on-stream or off-stream: photo-electronic analysis, or by systematic batch sampling (with some kind off electronic surveillance of the mainstream) and just send mixed, color measured cullet to only amber and green furnaces? The flint would-be simply included in the mix. This is probably technically feasible, but is subject to the market limitations noted in point1.

Jan 1, 1975

By A. Halim, A. Martikainen, S. GYAMFI

This paper outlines a unique case of the development of strategies to reduce ventilation and heating costs in Konsuln iron ore mine in northern Sweden. The mine, located just south of Luossavaara-Kiirunavaara Aktiebolag’s Kiruna iron ore mine, was developed as a test mine from 2018-2020 for the Sustainable Underground Mining (SUM) project. Besides functioning as a test mine, Konsuln also contributes to ore production. The existing mine ventilation system was designed for the current production rate of 0.8 million tons per annum (Mtpa). There is a plan to increase this rate to between 1.8 and 2.0 Mtpa.

Sep 30, 2021

By John Marsden

Despite the recent pullback in metal and mineral prices, and the associated market adjustments, the mining industry is still facing a serious issue with the declining availability of graduate expertise. This is due to a combination of an aging workforce, retirements and retrenchments, coupled with a lack of suitably qualified graduates entering the workforce. The issue has certainly improved since 2004 when the industry picked up the rates of hiring graduate engineers and mining/mineral school enrollments picked up in response. This hiring effort has helped to cover the ?gap? years from about 1985-2000, when industry demand for graduates was particularly poor. However, the recent market pullback is likely to set back this progress, as recruitment and hiring wavers as a result of cost cutting measures and economic uncertainty. A key issue for the mining industry is how to ensure the survival and growth of relevant ?core? degree programs. Such programs include mining, metallurgical, mineral processing and geological engineering. The mining industry needs a healthy, high-level education program to ensure an adequate supply of appropriately qualified graduates for the mining industry. Two-thirds of the professionals entering the minerals industry who graduated within the past 40 years graduated prior to 1985. Since 1985, we have been living off the legacy of graduation classes from the mid-1970s and early 1980s. It is estimated that we have been producing graduates at approximately 40 to 50 percent of the sustaining rate since about 1985. Further growth in the domestic industry would increase graduate requirements significantly, and the export of U.S.-graduates to other parts of the world (as is currently occurring) also impacts the total graduate requirements.

By R. H. Mullennex

Application of depositional analysis concepts is becoming an ever-increasingly more important and more useable tool in exploration and development of coals in the Appalachian basin. Over the past decade, a rather large number of studies, papers, and publications have addressed various aspects of depositional environments of coals and, to some extent, applications to development. As would be expected as regards a subject so complex as Pennsylvanian sedimentation in the Appalachian basin, certain academic studies have produced conclusions at variance in some aspects to those of other studies. Overall, however, there has been a building- block progression and general refinement with time of understanding of the depositional settings and other factors controlling Appalachian coal distribution, quality, and other minability parameters. Most attempts to explain coal seam characteristics have revolved around a basic deltaic model. Some have attributed certain seam attributes to upper delta plain deposition, other attributes to transitional-lower delta plain settings, and yet others to lower delta plain environments, and so on. While these approaches have provided valuable insight into some general coal characteristics, they are somewhat incomplete and are, in a sense, too broad for specific mine-scale applications. Further, it is apparent that in order for widespread peat accumulation to occur, there must be a drastic decrease in the energy of the depositional system and amount of sediment being brought in, compared to the active deltaic and coastal processes responsible for deposition of the large volume of clastic sediments that dominate the Pennsylvanian system of the Appalachians. Consideration of this fact implies that peats (coals) may not necessarily reflect depositional settings that are directly coincident with those associated with adjacent rocks. Cecil and Englund (1985) address this point, and quite correctly state that "the primary controls on major stages of peat formation are allocyclic processes involving paleoclimate, eustatic changes in sea level, and tectonics." While this statement is inarguable, it does not negate the importance and usefulness of depositional analysis in predicting reserve characteristics that may impact mining and marketability.

Jan 1, 1986