Search Documents

By Harry M. Edenborn, Richard W. Hammack

Experiments were done to determine if a mushroom compost-based sulfate reduction system could be used to treat nickel-contaminated mine waters. Sulfate reduction systems were established in columns containing acid-washed mushroom compost. Simulated mine waters containing 2000 mg/L sulfate and 50 to 1000 mg/L nickel were adjusted to pH 4.5 and pumped through the columns at flow rates between 15 and 25 mL/hr. During the first nine days of operation, virtually all influent nickel was removed in the columns by sorption and ion exchange mechanisms. The nickel removal rate then dropped to 18 to 30 mg Ni/day (7.8 to 12.8 nmol/ g-substrate/day), probably due to low sulfate reduction rates. When sodium lactate was added to the inflow, a sustained and seven-fold increase in the nickel removal rate was observed. Bacterial sulfate reduction rates measured in mushroom compost-based wetlands exposed to coal mine drainage are 2 to 20 times faster than the rates observed in this study. Low sulfate reduction rates in the columns may have been due to the inhibition of microbial activity by high nickel concentrations and the removal of labile organic compounds from the mushroom compost substrate during acid-washing. Results of this study indicate that bacterial sulfate reduction can effectively treat nickel concentrations up to 500 mg/L if labile carbon is nonlimiting.

Jan 1, 1992

By M. A. Marticorena, R. Stratton-Crawley, C. I. Basilio

Diethylenetriamine (DETA) is a selective depressant for nickeliferous pyrrhotite during pentlandite flotation. Laboratory flotation tests conducted on ore and process samples showed that pyrrhotite rejection is greatly improved by small additions of DETA; however, the effectiveness of this depressant is most noticeable when the mineral sample is oxidized. LIMS and XPS analyses conducted on flotation products and pyrrhotite specimens showed that the difficulty in pyrrhotite rejection arises from inadvertent activation of the mineral by heavy metal ions, such as Ni2+, cu2+ and Ag+, that are present in the process water. In the presence of DETA, however, the mineral is deactivated under oxidizing conditions. The deactivation mechanism may involve oxidation of the activation products, which are likely in the form of heavy metal sulfides, followed by solubilization by DETA. FTIR spectra of pyrrhotite electrodes contacted with DETA showed no trace of the reagent on the surface, substantiating the view that its role is one of complexing agent that enhances the dissolution of activation products under oxidizing conditions. FTIR spectra of pyrrhotite contacted with amyl xanthate solutions showed that both dixanthogen and iron xanthate are formed on the surface, the latter becoming more predominant at higher potentials. In the presence of DETA, however, only a small amount of xanthate is adsorbed on the mineral at potentials (Eh) approximately 200 mV higher than the case without DETA.

Jan 1, 1995

By B. K. Mishra, R. K. Rajamani, P. Songfack

Primary grinding in SAG mills is gaining more importance with respect to the conventional crushing, rod and ball milling operations. This is due to the reduced operating costs generated by lower steel consumption. However. SAG milling is inherently susceptible to more severe risks and problems since it attempts to combine several stages of the conventional crushing and grinding into a single stage. This paper analyzes the SAG milling operation by predicting the motion of rocks and steel balls. The well-known discrete element method (DEM) is used to calculate the trajectories of individual entities, and their collision with one another. A computer code previously used for studying the motion of grinding media in ball mills is enhanced to handle the interaction between heavy spherical steel balls and light chunks of rocks, usually ellipsoidal in shape. The DEM based software called MILLSOFT can animate the charge motion for different design of liners. A case study of a 9.75-m diameter SAG mill is presented and the effects of lifter bar height and configuration on the overall dynamics of the charge are discussed. Also the effect of spacing between liners on lifting the charge is presented. This new approach has a large potential because it shows in detail the effect of each design or operating parameter on the performance of SAG mills.

Jan 1, 1998

By Terry L. Logan, Arfon H. Jones, James C. Seccombe

Deeply buried coal seams [greater than 3000 ft (914 m)] are difficult and sometimes hazardous to test and complete due to coal sloughing, formation pressure anomalies and coal fine generation. Data collected while stimulating two deep coalbed methane wells located at the Gas Research Institute/Resource Enter¬prises, Inc. "Deep Coal Sean Project" test site in the Piceance Basin, Colorado, is presented in this paper. A single thick coal seam was completed openhole in each well. Core data, reservoir data, in-situ stress measurements, and pre-stimulation calibration test data were collected at the site to use in the design of the fracture stimulation treatments for both wells. A nitrogen foam fracture fluid treatment was selected for the first well and a linear gelled water for the second well. Treatment pressures were monitored with a downhole quartz pressure transducer. Atypically high treating pressures were observed, possibly indicating coal fines plugging at the fracture tip or increase in fluid viscosity caused by interaction of the generated coal fines with the fracturefl uid. In addition, a comprehensive fracture diagnostic effort was employed during the fracturing of the second well; namely, triaxial borehole seismic, seismic televiewer, hydraulic impedance monitoring, gamma ray log (in conjunction with radioactive additives in the sand), and temperature log. The results indicate a vertical fracture was created parallel to the face cleat as expected.

Jan 1, 1986

By C. P. Lazzara, F. J. Perzak, C. C. Hwang, C. D. Litton

Fire development and spread along conveyor belts in ventilated ducts were investigated experimentally and theoretically. Various types of conveyor belts used in mining applications were ignited and burned in a full-scale gallery under various flow conditions. The flame spread rates depended strongly on the ventilation air speed. The time-temperature traces of gas and belt obtained at 12 feet from the entrance show that a rapid belt surface temperature change takes place prior to a change in the gas temperature, indicating that radiative heat transfer from the flame to the belt surface plays an important role. Further, anomalies in the flame spread rate in the vicinity of 1.5 m/s air speed (i.e., much greater rate than that observed at either higher or lower speeds) can be explained through the mechanism of flame tilt and the resultant view factor between the flame surface and the belt surface. In order to correlate the fire spread with material properties of the conveyor belts (such as the specific heat, the thermal conductivity, and the pyrolysis temperature) and the fire environment (such as the gas temperature and the ventilation air speed), a theoretical model has been developed. This model is based on the experimental observation that the radiative heat transfer is the dominant mode of energy transfer ahead of the flame front. Agreement between the theory and the experimental results is good.

Jan 1, 1991

By V. N. Kolesnikov

The Sikhote-Alin part of the Circum-Pacific Ore Belt is characterized by wide distribution of Sn, Pb, Zn, W; Au, Ag, and other mineralization. This mineralization is regionally associated with the Late Cretaceous-Tertiary East Sikhote-Alin volcanic belt where it overlaps the Taukha accretiollary-wedge terrane of the Early Cretaceous age. The Pb-Zn deposits of the Dalnegorsk ore district may be grouped into the skarn (about 80%) and vein types. The skarn deposits are of major commercial value. Their geological position is controlled by the carbonate units located within tectonic melange of the Taukha terrane. Some other lithological and tectonic factors also play a significant role ill distribution of the mineralization. The ore bodies are traced to the depth of 1000-1500 m below the surface, having a pipe-lens shape and vertical zonation. Major minerals of the ores are galena, sphalerite, pyrrhotine, chalkopyrite, hedenbergite, quartz, and calcite. The minor elements of the Pb-Zn mineralization are cadmium, silver, bismuth, and copper. The paper describes relationships between mineral suites and minor element contents in the ores, as well as their significance for processing the ores. The metallurgy applied allows high recovering of the major components (Pb -93.9%; Zn -91.4%). However the tails contain some minor components that may be of commercial interest.

Jan 1, 1998

By Victor E. Archer

INTRODUCTION Man is exposed to many agents which induce mutations in germ cells and/or cancer at work, at play, and at home. In this total mix of mutagenic and carcinogenic agents, how important are radon and its daughters? Before man moved into caves and other permanent dwellings, the principal mutagenic and carcinogenic agent to which he was exposed was natural background radiation--cosmic rays, radium and potassium-40 in his food, plus gamma rays and radon from the soil and rocks. When man moved into caves, captured fire, and began to preserve and store foods, his exposure to carcinogens and mutagens took a quantum leap. Carcinogens and mutagens appear to act in the same way, that is, by altering the DNA or nuclear proteins of cells. Most mutagens are carcinogens, and vice versa, so when I say mutagens from here on, I will be referring to both. The relationship of the two is emphasized by the fact that administration of a carcinogen to a group of animals not only increases cancer rates among the exposed animals, but also among their progeny (Tomatis 1979). Environmental Mutagens Smoke from man's fires, overheated foods, and foods preserved by smoking, resulted in ingestion and inhalation of many polycyclic aromatic hydrocarbons--many of which are mutagens. Caves and houses with tight windows and doors tend to collect the radon which is constantly emanating out of soil, rocks and concrete, so man's exposure to the radon daughter component of background radiation increased several fold. Preserving food by salting or pickling with material that contained nitrites and nitrates led to increased ingestion of nitrosamines, which are potent mutagens. When his grains and other foods were stored in slightly damp rooms, fungi or mold would grow on them. Several of these fungi are now known to produce very potent mutagens. The best known of these is aflatoxin B (Ramachandra 1979). It may seem strange that a living organism would produce a mutagen. One might think that it would scramble its own genetic heritage. The reason it does not is that it produces the mutagen in an inactive form. It can be activated only by an animal's enzyme systems after being eaten. When man moved into cities, the collective smoke from wood and coal fires further increased his exposure. That particular smoke has now mostly disappeared, but has been replaced by smoke from automobiles and industry. When man moved into the age of technology, his exposure to mutagens again increased dramatically. Many mutagenic chemicals, from benzene and beta naphthylamine to a long array of pesticides and tobacco products have been added to our environment. Excess deaths from cancer are now being observed among chemists in most industrialized nations. Mutagens are even found in much of our wine, beer, and whiskey (Keller 1980). Some of the chemical mutagens were widely used in food or in other commercial products before their potential was discovered. Striking examples of this is the original butter coloring agent and the polychlorinated biphenyls that have been widely used in brake fluids and electrical transformers. Large quantities of them have been discarded or disposed of in a careless manner--in such a way that many of them have contaminated our food, our ground water and air (Landrigan 1981). In this nation, with the help of several recent laws, we were just beginning to get control of the industrial chemical mutagens. With the relaxing of these laws that is currently going on, it appears that it will be many more years before we really bring chemical mutagens under control. Many nations have yet to come to grips with this problem. On top of this massive array of chemical mutagens we have now added radiation from many artificial sources. For most of us this means medical X-ray and fallout from nuclear weapons testing. Ionizing radiation is one of the most potent mutagens, so it has caught the public eye, and its contribution cannot be ignored. Fortunately, by the time we started using radioactive materials in quantity with the Manhattan Project, we had experience with radium and X-ray (some of it bad); we knew enough radiobiology and enough about methods of radiation protection so that most nuclear laboratories have had a phenomenal record of radiation safety. Radiation is one new technology with great potential for harm that has not exhibited that potential except for a few isolated situations like that of radium dial painters, uranium miners and atomic bomb victims. Uranium miners slipped into this list almost by accident. We could have protected our uranium miners just as well as we did the workers in nuclear laboratories; but we failed to do so. Why didn't we? The reason is simple. The Atomic Energy Commission was charged with protecting the health of their workers. They did not wait for a pile of bodies before they introduced controls. Congress appropriated the money, and taxpayers were willing to pay for the protection against radiation. Miners unfortunately did not work for the Atomic Energy Commission. Although mine operators were ignorant about radiation, the key item was that in the 1950s nobody was willing to pay the extra costs of adequate ventilation to control the high levels of radon and radon daughters in uranium mines. Control was not achieved until new laws and regulations were passed which made it compulsory. BIRTH DEFECTS AND CANCER

Jan 1, 1981

By L. Tondo, W. Lim

The high pressure grinding rolls (HPGR) is a relatively new technology which offers the potential benefits in energy savings, circuit simplicity and improved product characteristics in minerals processing applications. Over 300 machines are now operating world-wide, but most of these are used for grinding cement clinker, and relatively few are used in conventional mineral processing. One of the rea- sons for its current limited use in the minerals processing industry is that design, scale-up and flowsheet assessment procedures are seen to be relatively immature and untested. This has reduced confidence in the potential application of the technology. To help rectify this situation an industry funded research project was undertaken, one of whose aims was to develop and prove a mathematical model of the HPGR and a scale-up procedure. Data were collected from tests using laboratory, pilot and in one case a full scale unit (2.2m diameter). A range of feed types were tested including quartz, limestone, kimberlite, bauxite, iron ore and gold ore. These data were then used to develop models of the size reduction performance, power draw, throughput and operating gap for a wide range of pressures, feed sizes, and roll speeds. This paper describes the models that have been initially developed and illustrates their accuracy using some of these data.

Jan 1, 1998

By Levent Ozdemir, Gerald Dollinger

An extensive series of linear and rotary cutting tests were run in soft and medium strength rocks at the Earth Mechanics Institute of the Colorado School of Mines to investigate the possibility of very high speed mechanical excavation for tunnel, raise, and shaft boring. The results of these tests demonstrate that cutter penetrations of 38.1 mm (1.5 inch) and cut spacings up to 228.6 mm (9 inch) are possible in such rock without exceeding the bearing capabilities of the cutters. It was also demonstrated in vertical boring tests that continuous excavation rates up to 38.1 m/hr (125 ft/hr) can be achieved with state-of-the-art technology provided sufficient thrust and torque is available. A predictor model for soft rocks was also developed using the test data. Analysis of this model shows that the errors between the predicted and observed cutter normal loads appear to be independent of cutter diameter, tip width, cut spacing, and depth of penetration. This suggests that the structure of the model is correct with respect to these variables. An analysis of the coefficients in the model was also made and a correlation found between the principal coefficient and Unconfined Compressive Strength. The second coefficient in the model was found to be similar in magnitude to rock properties such as Brazilian Tensile Strength, Shear Strength and Point Load Index.

Jan 1, 1989

By Pierre M. Matheron

TRANSMANCHE-LINK is responsible for designing, developing and implementing the project for a fixed link under the English Channel, comprising two running tunnels of diameter 7.6 metres and a service tunnel of diameter 4.8 metres. The three tunnels will all be 50 km long, with 37 km bored through chalk marl at a depth of 40 metres under the sea bed. The tunnels will be driven from both sides of the channel from intermediate addits above the coastline on either side with a 55 m access shaft at Sangatte in France and two "descenderies" or inclined tunnels addits and a shaft at Shakespeare Cliff on the English side. A total of eleven tunnel boring machines will drive the 150 km of tunnels. The major part of the tunnel linings will be built of precast reinforced concrete segments, and two plants have been specially built to produce the necessary 725,000 segments. Seven million cubic metres will be evacuated on wagons along the tunnels and then lifted by belt conveyor on the English side, and by hydraulic mucking from the bottom on the French side. Preliminary work started early in 1987 with manufacture of the first boring machines, construction of five precasting plants, boring of the Sangatte shaft in preparation of the Shakespeare Cliff entrances. The principal project dates are :

Jan 1, 1987

By Vinton A. Garbesi

The construction involved in the Washington Metropolitan Area Transit Authority (WMATA), Contract No. lK0011 (K-1), encompassed some 2,621 meters of single track parallel tube rapid transit tunnels, 335 meters of cut-cover subway station and appurtenant ventilation structures at each end, and a fan shaft at approximately the mid point of the tunnels. The construction contract was awarded June 7, 1974 to a Joint Venture consisting of Intercounty Construction Corporation, Hyattsville, Maryland, and S $ M Constructors, Inc., Solon, Ohio. The former being responsible for performing the cut and cover construction, and the latter being charged with constructing the running tunnels and fan shaft at their mid point. (See Fig. 1) The problems of mining and supporting, the 183 meters of twin tunnels just east of Court House Square Station, by unique mixed face and soft ground mining methods is the main subject of this report, although a general review of the tunnels in their entirety, as well as the geology encountered in the excavations, is presented to give a better overall setting for the problems encountered. GEOLOGIC SETTING The tunnels for the K-1 contract are located in three general types of material; the first being fractured and metamorphosed ignious rock (quartz-hornblende-biotite gneiss), the transition zone between weathered and competent rock, and in ground consisting of the weathered

Jan 1, 1979

By Gary W. LaChapelle

Cyprus Miami Mining Corp. has a history of overcoming adversity through innovation and adaptation to changing conditions. Requirements to remain profitable in the 1990s include a combination of advanced technology, employee involvement and training, attention to customer satisfaction, environmental awareness and quality management. The Miami property is located in the Globe-Miami area of Arizona, 130 km (80 miles) east of Phoenix and 160 km (100 miles) north of Tucson. The complex is located in a high desert environ¬ment at an elevation of 1065 m (3500 ft). The region receives about 480 mm (19 in.) of precipitation annually. History Mineralization at the Miami property was first discovered in the 1880s, which led to underground mining of copper by the 1890s. In 1911, the Inspiration Consolidated Copper Co. was formed by combining the Inspiration and Live Oak Mines. Full-scale production began in 1915. Block caving methods were used at both mines. Open-pit mining commenced in 1948. Underground mining had ceased by 1954, and all production was obtained from surface operations. Innovation has been the key to Miami's success. Development of sulfide flotation and the ferric cure process for vat leaching were advanced at Miami. In situ leaching of oxide material, remaining after block caving had removed the sulfide ore, was also used.

Jan 1, 1993

By Mark E. Smith

To allow recovery of gold values from ore which cannot be economically processed by the mill, Pinson Mining Company has developed a run-of-mine heap leaching facility. In order to estimate production scale recovery rates, reagent consumption and percolation problems, a series of pilot scale tests were performed. These tests typically consisted of 3,630 metric tons (mt) (4,000 tons) leach ore at a grade of .94 to 1.56 grams per metric ton (g/mt) (.03 to .05 oz.) Au/Ton. Test heaps were loader stacked to approximately 4.3 meters (14 feet) high. Information from these pilot scale tests was employed in the design and construction of the production scale facility. Parameters such as spray rate, leach cycle, sprinkler placement, and barren solution chemistry were determined by the pilot tests.

Jan 1, 1983

By H. C. Juvkam-Weld

R. Michael Craig Mr. Juvkam-Wold's article is a timely and much needed presentation of the method of depressurization to reduce ground-water inflow into mine shafts. The article is very informative and discusses the effects of depressurization upon shaft inflows adequately. However, the article omits a discussion of another important benefit of depressurization: the reduction of potential for artesian burst or, as it is also called, floor heave. Confined aquifer systems (artesian aquifers) can contain water under several hunder pounds per square inch (psi) of pressure. For example, water levels at elevations of 455 m (1500 ft) or more above the top of the Westwater Canyon member of Reply by H.C. Juvkam-Wold In general, Mr. Craig's comments are useful and accurate regarding the potential benefits of aquifer depressurization. However, two of his points require further explanation since they may lead to a misunderstanding of my paper and its predictions. These refer to his comments regarding failure to account for storativity and to non-artesian conditions. Equation 5 is indeed Darcy's steady state equation. However, as a careful review of the appendix in this paper will reveal, I have used this equation to represent semi-steady state conditions. In other words, steady state conditions are assumed at any instant of time, but conditions may change gradually from

Jan 2, 1983

By J. A. Herbst, C Lo. Y, Z. Rogovin

The identification and quantification of incipient overload conditions in mills have recently been found to be very significant in the design of tumbling grinding mills. To investigate these phenomena, a series of experiments was conducted in a Plexiglas mill operated in both dry and wet modes. For on-stream measurement of the mill charge weight, volumetric filling, dynamic angle of repose, and mill power, an electronic system was developed. The mill was filled to various levels with 19.1-mm (3/4-in.) ceramic balls as grinding media. As feed material, grindable limestone or 3.2-mm (1/8-in.) nongrinding ceramic balls were fed at various steady-state rates to determine the incipient overload conditions. The prediction of overload has apparently been reduced to predicting the feed rate that results in 50% mill filling.

Jan 1, 1988

By Robert Roggenthen

In 1994, ASARCO's Mission Complex Mine Planning Department designed a new stripping schedule to take advantage of reserve opportunities. Based upon the new stripping design, overburden removal exceeded available hauling capacity. This increased hauling capacity requirement required that ASARCO consider alternative technologies for material transport. In 1997, ASARCO Mission Complex completed the purchase and installation of a 3.5 km, 8,600-tph conveyor system to transport waste material. The conveyor system is composed of two apron feeder/sizer units manufactured by Mining Machine Development LTD. and a conveyor system manufactured by Krupp-Robbins. This paper will review the option of truck haulage versus conveyor transport for overburden removal by (1) describing engineering studies contributing to the solution, (2) researching proactive options to create alternative management decisions, and (3) revealing final results of the project.

Jan 1, 1998

By B. Huang, H. Sevim, R. Honaker

The use of medium-to-high sulfur coals has been negatively impacted by the 1990 Clean Air Act Amendment (CAAA). In this article, a method is demonstrated that can render these coals competitive and yet compliant with Phase II of CAAA. The method uses strategic mining and optimized preparation plant operation to minimize production costs, and it utilizes advanced coal-cleaning technology and an SO2 allowance to produce a compliant coal. The method is illustrated through an example from southern Illinois. For an annual production of 3.2 Mt (3.5 million st) and with a $150/st SO2 allowance cost, it was possible to produce a competitive coal for $0.84/million Btu. The production and allowance costs were $0.608/million Btu and $0.232/million Btu, respectively.

Jan 1, 2002

By Herbert M. Mandel

INTRODUCTION Designers of major public works projects in the past have displayed varying degrees of environmental consciousness, and tunnel designers in particular have always had to deal with certain environmental considerations - ventilation, lighting, aesthetics - as matters of primary design. Today, however, with a widening sector of the public becoming environmentally aware, tunnels are treated as elements of whole transportation systems, and are subject to increasing environmental scrutiny. The Route H-3 tunnels in Hawaii are examples of the time, care, and detail involved in a major rock tunnel project. Project Description The Route. Interstate Route H-3 is a proposed 10-mile highway crossing the Koolau Mountain Range on the island of Oahu, Hawaii, providing a direct connection between the Pearl Harbor area and the windward part of the island in the vicinity of Kaneohe. It is designed as a dual highway with provision to accommodate mass transit. As shown on Figure 1, the project includes two sets of twin bore tunnels (through the Main Koolau Range and through Red Hill), three highway sections of which two are through largely undeveloped mountain valleys (South Halawa and Moanalua), a viaduct, and three interchanges. From the Halawa Interchange to the Kaneohe Interchange, the proposed highway consists of two 3-lane roadways separated by a median where the highway is at grade. One lane of each roadway will not be constructed initially but will be landscaped and reserved for mass

Jan 1, 1974

By P. Zhang, D. W. H. Su, M. Van Dyke, H. Dougherty

This paper describes the scientific data acquisition, data interpretation, and sophisticated 3-dimensional modeling processes of an ongoing gas well stability research program by the National Institute for Occupational Safety and Health (NIOSH). Results from the NIOSH field instrumentation programs and the parallel 3-dimensional numerical modeling programs indicate that overburden depth, overburden geology, surface topographic relief, strata dip of the coal measure rocks, and casing cementing alternatives are the dominant factors affecting longwall-induced subsurface deformations and gas well casing stresses. Topographic relief could produce localized longwall-induced deformations if weak-to-strong rock interfaces are present near the bottom of stream valleys. Strata dip has significant impact on longwall-induced subsurface deformations. Cementing alternatives are found to have significant impacts on longwall-induced deformations and gas well casing stresses.

A linear programming model with integer sequencing variables is developed to schedule limestone production for a quarry in Central Japan. The model is used to optimize raw material production from the quarry supplying limestone to cement, quick lime and aggregate plants. Typically, the mining in the quarry takes place in four to six different areas each area having 3 or 4 mining increments. Each mining increment contains different quality of limestone. The limestone production from the quarry is transported to the plants byway of 3 ore passes. Each plant requires a given quantity of limestone per period meeting certain quality constraints. This paper will describe development of the scheduling optimization model and how it is used to schedule production by period within the quarry to meet the capacity and blending requirements of the plants.

Jan 1, 2003