Search Documents

By Michael S. Kucker, Robert A. Robinson, Harvey W. Parker

Ground deformations are of major concern during tunneling, especially in downtown environments, since they have a significant impact on the costs and practicality of tunneling. This case history describes soil and groundwater conditions and ground behavior during the construction of twin transit tunnels for the Downtown Seattle Transit Project (DSTP). The tunnels were excavated through complex glacial soils ranging from hard glaciomarine drift to flowing sand. The tunneling process was greatly facilitated by the prediction of soil layer positions to an accuracy of ±0.6 m (2 ft). Tunneling was complicated by the presence of over 500 temporary tiebacks and by disturbed ground overlying an operating railroad tunnel. A variety of ground improvement techniques were used to successfully minimize settlements, which ranged from 1 cm (0.4 in.) in glaciomarine drift to 6 cm (2.4 in.) in flowing sands. Ground improvement techniques included compaction grouting, chemical grouting, jet grouting, and eductor well systems.

Jan 1, 1991

By Phil D. Newman, Robert J. Pine, Kevin Ross

The Stratoni Operations in northeastern Greece rely on a selective backfill method to exploit high-grade lead-zinc deposits. Underhand cut and fill often results in spans approaching 6-9 m (depending on the mining method employed) and a competent backfill is required to avoid dilution problems. Cement consumption represents a significant mining cost and through improving the control of the backfill batch preparation, the cement content could be greatly reduced without jeopardizing the grade control. A new distribution system was installed and a QAIQC system designed in cooperation with the operators to allow a wide range of backfill recipes, providing cost savings to the mine. A review of possible failure modes and the consequent strength required for the chosen mining method was also completed and indicated potentially significant cement content reductions. The calculations are supported by 12 years of experience at the mines which provides a valuable insight into the applicability of the approach developed.

Jan 1, 2001

By Dan G. Wasyluk, Meryl J. Klassen, Tony J. Morris, Clive H. MacKay

The Rogers Pass Project in British Columbia has involved the construction of two railway tunnels totalling 16.6 km and a 345 m deep shaft. Systematic geological mapping was carried out at four headings during construction. The paper discusses the procedures used to record the geology, structure, rock mass characteristics and excavation performance. Coded data from the geological mapping and shift inspector reports was entered into a computer data base. The rock mass quality was evaluated for both the Geomechanics and Q classification systems. Continuous computer generated graphic logs were produced showing the excavated perimeter map, geological parameters, installed support and construction activities. The tunnel logs were updated on daily basis and used during construction by project staff for evaluating support requirements and monitoring excavation progress. The specific requirements, difficulties and advantages in mapping tunnels using a computer based system are compared to those of a conventionally mapped tunnel excavation with hand drafted tunnel logs.

Jan 1, 1987

By V. Saltas

In the present work, dielectric spectroscopy experiments were conducted on bentonite samples collected from Milos Island, in order to study their electrokinetic behavior in correlation with water content and mild heat treatment. Low-frequency dielectric spectroscopy has proved to be a power tool in the study of the electrical behavior of clay-water systems, because polarization and relaxation processes typically affect response at frequencies below 100 kHz. Therefore, dielectric and conductivity measurements in the frequency range of 10mHz to 1MHz were carried out by means of a high-resolution broadband spectrometer on bentonite samples, at various levels of hydration. The evolution of dielectric response was also examined after annealing of the samples. Experimental data were computer fitted with the empirical Havrilliak?Negami dielectric relaxation function on which a conductivity term was superimposed. The evaluated parameters of the fitting function are shown to be strongly affected by the water content of the measured samples.

Jan 1, 2006

By Steve Kral

It is agreed in mining and regulatory circles that a safe and healthy working environment for underground miners is the major challenge for mine operators. Underground mine ventilation is complex. And it is becoming even more difficult as mines become larger, deeper and more complicated. At the Seventh US Mine Ventilaton Symposium, a group of mine ventilation experts from industry, government and academia attempted to solve some of the problems in ventilating underground mines. The meeting, sponsored by the Underground Ventilation Committee of SME and the University of Kentucky, was held in Lexington, KY June 5-7, 1995. Andrzej M. Wala, symposium chairman, commented that previous mine ventilation symposiums have focused mainly on work in North America. The 1995 symposium, however, broadened its borders to include several international papers. Of the 77 papers presented and bound into the Proceedings volume, 25 are from operations and research centers outside of the United States and Canada.

Jan 1, 1995

By C. W. Schultz

The Mineral Resources Institute at The University of Alabama is engaged in a program whose objective is to develop a beneficiation system for Eastern oil shales. Prior experience (1,2) at The University had shown that the grind required for liberation of the oil rich kerogen was substantially below 20~m. Based on this fact and the rapidly emerging consensus that column flotation is the preferred method for ultrafine particle separation, efforts were focused on the column flotation of oil shale. This paper, which must be regarded as a progress report on a continuing MRI project, describes the observations made and the results achieved to date. The investigation is being conducted in two phases. The first phase has been completed and consisted of a factorially designed experiment conducted for the purpose of screening a set of primary flotation variables. The second phase, which is still in progress, is focused on optimization of the operating conditions and development of a flowsheet for specific shales.

Jan 1, 1989

By Peter V. Avotins

During last year's AIME meeting in New Orleans, Deepak Malhotra and I were discussing some of the topics that would be presented in this Symposium. It seemed appropriate that along with papers on specific reagent and flocculant types, we should address research management aspects of new product development. This development is a long, arduous task that requires a significant technical and fiscal commitment by the chemical company and potential users. A flow chart depicting the research process is shown in Figure 1. The sequence of events are plotted on an undefined time line. Our experience has shown that it takes 3-5 years to complete a typical reagent development project. A new project starts with an idea of how to do something better. The ideas range from relatively simple product modifications to opportunities created by technological change. An example of this is the use of flocculants in tailings operations to close the water recycle loop. The change was brought about by the need to conserve water and comply with environmental statutes. The result was the development and wide-spread use of synthetic polymers to help in solid-liquid separation. More recently the ups and downs of oil prices have led to development of coal water slurries as an alternative to fuel oil. The slurries contain high levels of chemicals (up to 3%) to insure proper stability and burn characteristics. There are technical changes under way right now that may lead to ideas for other new products. One exciting source of new technology is the ability to manipulate genetic material of microbes to select for specific capabilities. This has evolved by leaps and bounds over the past 5 years. Biologically assisted leaching and removal of wastewater impurities are two possible end uses. I'm sure that there are many others. The ideas can originate anywhere and are often half-baked at first, but to lead to new products they must be refined to provide project definition and eventually a research plan. A chemical ,development project cannot be started without approval to commit the company's resources. The internal selling job is often very difficult. The company must see clear financial benefits in order to launch efforts that may not pay off for many years. It is critical to project the total market, profitability, eventual market share, and timing of introduction of the new product. There is much uncertainty in this and the research manager is often skating on thin ice to retain his credibility. Once we obtain support from upper management, the research team is assembled to start the project. The teams generally consist of organic chemists, research metallurgists, and technicians. They have access to analytical scientists and technicians for surface and analytical chemistry. The projects are often augmented by help from university staff and consultants. This is particularly true where there is a need to develop fundamental understanding of the technology in addition to synthesis of chemicals. The project now proceeds along two lines. First, there is an emphasis on understanding the prior art. Extensive literature and patent searches are undertaken to provide research leads and to keep from "reinventing the wheel" and infringing on someone else's patent. The scientists and technologists are qualified to conduct computer-assisted library searches. This process usually uncovers 80-90% of the relevant information. The remainder is very much harder to get and requires the help of professional library search staff with scientific backgrounds. Along with literature searching, the team begins synthesis of new compounds. These are screened by use of techniques such as microflotation or filtration in a Buchner funnel. The scientists are looking for the direction of response as they modify structural features . Inevitably, a large number of candidates reach the next stage, a laboratory bench test. At this point it is possible to set up a research plan and use project management techniques to monitor progress. The bench tests are conducted in larger equipment, usually requiring 100-1000 grams of test substrate. Typical laboratory flotation tests are run in Denver or Wemco cells.

Jan 1, 1986

By P. Walshe

A common belief among Itlnl.ng operators today is that computer based truck m:mitoring and dispatching systems are only applicable to, or affordable by, very large scale open pit mines. Before the advent of microcomputer technology this belief was generally a valid one. Microcomputer technology as it currently exists has reached a high level of sophistication and capability, rapidly approaching that of the minicomputer standard. When coupled with reliable software and data communications packages, it now provides the means to make truck monitoring and dispatching a viable and attractive management aid to mines of all sizes. This paper briefly addresses the evolution and current state of computer truck dispatching and examines a microcomputer based system in this context. To demonstrate the effectiveness of this approach to truck dispatching a recent installation in a medium sized mine is presented. Preliminary field data from the case mine are presented to illustrate the methodology.

Jan 1, 1989

By S. D. Rosenthal

"This article will share my ‘shift in career direction’ journey from corporate mine engineer, with 31 years of mining various commodities with a wide range of responsibilities in a variety of countries, to the world of academia. There are times in one’s career that a change is required, albeit perhaps not as drastic of a change as moving to teaching. This paper will share how the transition arose, the decision to make the change, the challenges of the first year in academia and the journey within academia going into the second year.As a graduate of the Montana College of Mineral Science and Technology (Montana Tech) with a B.S. mining engineering degree in May of 1982, my first job with Utah International in the Farmington, NM area took me back to my home state of New Mexico. Some of you will remember that the early 1980s was not a period of prolific opportunities for mining engineers, given low commodity prices, especially for copper (for example, Anaconda Co. had been taken over by Arco and was in the midst of closing down its Butte operations). Coal was good and the learning opportunities abounded with Utah (which became BHP and then BHP Billiton).Gold was taking off in the mid to late 1980s thanks to use of cyanide and heap leaching technology improvements, coupled with deregulation of the gold price, so I ventured off to work in the gold industry with a (then) junior Canadian company called Barrick at a new acquisition of theirs known as Goldstrike. That same gold surge was causing a shortage of iron ore mining engineers in Australia. So after a few years in Nevada, I uprooted the family and left for a little town in the Pilbara of West Australia, known as Newman, to work in the iron ore industry with BHP Iron Ore. An initial short overseas posting turned into six plus years before transferring to BHP’s Indonesian steam coal mines in Kalimantan on the island of Borneo. BHP was going through a rough period following some ill-fated projects (Magma Copper purchase, Beanup and HBI) and was reviewing assets and staffing, so internal opportunities became scarce. Employees were encouraged to “leave the company and find work elsewhere.” So, off I went to Argentina to try copper mining in the Andes with Minera Alumbrera. This short stint in South America was followed by a move to another mining town, Morenci, AZ, and a posting with Phelps Dodge (now Freeport- McMoRan). After 12-plus years without living close to snow, we moved to the Denver, CO area in a new position with Newmont Mining Corp. Along the way I became a professional engineer (Nevada) and completed a masters in project engineering and management. After 11 years with Newmont, I moved to Butte, MT where I accepted a position as assistant professor of mining engineering."

Jan 1, 2015

By R. Schuerch, C. Cimiotti, M. Piemontese, N. Karlin, P. Perazzelli, P. Halton

The new Los Angeles, California JWPCP effluent outfall tunnel will transport secondary-treated effluent from the Joint Water Pollution Control Plant in Carson to White Point Manifold. The tunnel will be approximately 7 miles (11 km) long with a finished internal diameter of 18 ft (5.5 m). The TBM is designed to cope with high water pressure up to 10 bar. The geotechnical challenges are due to the heterogeneous subsurface conditions: in the first half of the alignment, the tunnel runs through soils with a low overburden under urban areas, and, in the second half, the tunnel runs through extremely weak, intensely faulted rock masses with high overburden. Following an overview of the project, this paper focuses on the northern portion of the alignment and presents a decision-making procedure developed during pre-excavation phase in order to cope with the expected heterogeneous conditions during mining. The risk assessment and the TBM operational design of the southern portion will be dealt with in a future paper.

Jun 13, 2023

By J. Patrick Powers, Joel Miller, Arthur B. Corwin

A combination of a slurry trench with dewatering successfully controlled groundwater for a large sloped excavation immediately adjacent to the Arkansas River. The Murray Hydro Electric Project required excavation through sand and gravel to bedrock, 85 feet below high water in the River. The perimeter system of deep wells pumping up to 25,000 GPM (1,600 1/sec) lowered the water level to 15 feet (4.6 m) above bedrock. A short soil/bentonite slurry trench near the toe of the slope cut off the residual head. The method cut six weeks from the critical path. Design of the slopes and the dewatering system demanded high safety factors because of risk to existing Lock and Dam No. 7. A localized pocket of soft organic clay was supported by a rock filled bolster. A major flood event was successfully withstood. The method can be applied to large civil excavations and open pit mines.

Jan 1, 1989

By Charles S. Phillips

Kaiser Aluminum and Chemical Corp. (KACC) had been discharging spent bauxite-generally referred to as red mud-into the Mississippi River for almost 20 years when, in 1972, it agreed to store the waste solids on land. KACC decided to utilize a DREW system (decantation, drainage, and evaporation of water) where the spent bauxite is deposited in a large drying bed, surrounded by a 9-m-high levee. At the bottom of the bed, corrugated, perforated plastic pipe is encased in filter sand. The company built one DREW bed at Gramercy, LA, in 1973 and a second at Baton Rouge in 1974 using draglines, tractors, and rubber-tired scrapers. When a third bed was needed in 1977, the estimated construction cost using draglines was judged too high and KACC personnel began searching for a better, less expensive method for constructing the levee. A bucket-wheel excavator and conveyor system was selected and has proved to be less costly than more traditional earth-moving systems.

Jan 7, 1980

By Claude Boisjoly, Pierre de Courval, Don Nguyen

The Sainte-Marguerite-3 (SM3) hydro project, presently under construction, requires the excavation of an underground powerhouse and large water conveyance tunnels. This paper describes the planning of the project, main features of underground structures, excavation techniques and ground support.

Jan 1, 1997

By W. O. Henderson, H. W. Seaney

The sinking and grouting methods employed at the 3C and 3D ore hoisting shafts and the No. 5 service shaft are discussed. The reasons for selecting a circular section over a rectangular one and other technical aspects are reviewed.

Jan 1, 1974

By D. Spindler

Pursuant to the Federal Surface Mining Act of 1977 and the Illinois Surface Mining Act of 1980, Illinois has adopted revegetation success standard regulations that include the Agricultural Land Productivity Formula. The Formula establishes yield goals and standards to measure the success of meeting yield goals for reclaimed prime farmlands. The formula compares the quality of the pre-mining soils in the permit area and the county, to the crop production achieved on the reclaimed permit area and the county crop yield in a given crop year. The regulations also specify acceptable crops, erosion control requirements and time frames for demonstrating success.

Jan 1, 1986

By Gary A. Perry

Cyprus Sierrita produces copper and molybdenum from its Sierrita and Twin Buttes open pit mines south of Tucson, AZ. Both pits were started in the late 1960s and are more than 460 m (1500 ft) deep. Sierrita has used a Caterpillar 992C Remote Controlled Loader since January 1993. The loader was justified to increase safety and profits at Sierrita. It has exceeded all expectations. As of June 1993, the 992C had produced additional profits of more than $1.5 million. Safety and Geotechnical The safety of Cyprus personnel and equipment is always of prime concern. The remote controlled loader removes personnel from the active raveling area. But it requires prudent operation. The remote controlled loader discussed here is always intended to be used in a safe manner under a managed slope. Any increase in slope angle or use of any equipment under a critical slope is taken only after careful analysis of the specific

Jan 1, 1994

By Harry Holle, Gary Johnson

A plant trial was conducted at the Paddy's Flat plant of Dominion Mining Limited with the aim of comparing the ef evenness of oxygen and hydrogen peroxide as leaching oxidants. The Paddy's Flat plant is designed such that the leach train can be divided into two parallel streams, allowing the same or lurry to be eated in two identical trains. By effectively ehminatmg the influence of the ore variations on the results subtle differences in the performance of the two reagents hav been identified. . . The results of the plant trial indicate that the two reagents act m different ways, and that each may be more suitable than the other _for _the treatment of certain types of ore. In some cases a co bmation of the two reagents may be the most cost effective option. . or t e same chemical conditions in the leach pulp, including dissolved oxygen levels , the reagents achieve different gold leaching rates, and in some cases different ultimate leach extraction.

Jan 1, 1992

By P Simpson, P Bundo

The Eureka Mine is situated in the Guruve district of Zimbabwe, some 150 km north of Harare. The mine was first worked in 1895 and until recently was operated as a typical Zimbabwean "smallworking" with a single owner­operator and small labour force mining at up to 50m depth and processing 50 tonnes per day of ore via grind, gravity recovery and CIP. The gravity circuit comprised a Knelson 12" Centre discharge Concentrator from which a significant but variable portion of production was recovered. In 1996 exploration was commenced by Delta Gold Zimbabwe (Pvt) Ltd (DGZ), a wholly owned subsidiary of Delta Gold NL of Australia, with the aim of testing mineralisation and establishing a large-scale open pit operation. A feasibility study was completed in April 1998. Construction began in August 1998 and first gold was poured in June 1999. The mine is designed to produce 65 000 oz/annum of gold from 1.5 million tonnes of opencast ore grading 2 git Au.

Jan 1, 2000

By SAMUEL A. LOLON, ADITYA JUGANDA, JURGEN F. BRUNE, JR. GREGORY E. BOGIN

Historically, there have been many events of mine fires and explosions recorded in the United States and other countries that have demonstrated the existence of explosive methane-air mixtures, herein referred to as explosive gas zones (EGZs) [1]. The risk of mine explosions can increase if these EGZs migrate out from the gob into the surrounding mine entries — a phenomenon known as gob breathing. A number of 3D computational fluid dynamics (CFD) simulations using various magnitudes and periods of barometric pressure variation have indicated that the EGZ outgassing potentially occurs due to lags in pressure, which are strongly influenced by mine conditions and ventilation systems. Early-warning systems with real-time pressure monitoring and the application of gob ventilation boreholes are recommended to detect and mitigate explosion hazards from gob outgassing.

By Jennifer King, Julius Strid, Steve Brandon

The Upper Hidden Basin Diversion (UHBD) tunnel was driven approximately 1.2 miles by the drill-and-blast method primarily through massive granite bedrock geology for the Kodiak Electric Association, Inc. (KEA) in Kodiak, Alaska. The tunnel was driven from both portals with a constant 11-ft straight-leg horseshoe cross-section. The design and construction of the tunnel was driven by logistics and weather conditions due to its remote location and the rugged terrain of the project setting. This paper will discuss the successful completion of a challenging project over a ve-year period from preliminary planning through the design and construction phases.

Jun 23, 2024