Search Documents

By Matthew Goff, Russell Lutch

The Great Lakes Water Authority (GLWA) operates the largest regional water authority in the State of Michigan. Two of the tunnels supplying raw water to the system from the Detroit River are the Springwells and Northeast Tunnels. The existing 70- to 90-year old concrete lined tunnels have experienced distress and cracking over their life requiring non-structural repairs to sections of the tunnels. For the repair, an interior stainless-steel segmental liner plate system has been designed to restore the watertight capacity of the tunnel liner and resist the exterior hydrostatic groundwater pressure in a dewatered condition. The team is utilizing a “wet repair” approach to perform the necessary repairs while the tunnel remains fully flooded and operational. To test and validate the tunnel repair approach, a full-scale mock-up of the proposed repair has been performed using underwater equipment and divers.

Dec 1, 2022

By Vincente M. Jr. Lim, Brain W. Lawrence

Underground mining operating costs consist pri¬marily of direct costs such as labor, supervision, ma¬terials, and supplies, plus indirect costs. The material and supply costs vary substantially between mines but commonly range from 35 to 60% of the total direct costs. As part of the preparation of accurate operating cost estimates for a project, information must be as¬sembled to select the material and supply items and to determine the quantities of these items that will be required. Cost data then can be incorporated with the estimated material and supply requirements to determine the total material and supply costs for the project. Estimated quantities will vary considerably between mining projects depending upon factors such as the type of material being mined, the mining method, the equip¬ment selected, drilling and blasting techniques, mucking and haulage methods, ground support requirements, number of men employed, etc. Valuable information often can be obtained from suppliers and manufacturers, including data on current operating practices for similar projects, recommenda¬tions for the specific project, and preliminary cost quota¬tions. However, quotations obtained for estimates are generally higher than the prices paid at the time of purchase. Mines operating in the area, or those mining under similar conditions, also can provide essential design information, but it often is difficult to obtain cost information from the operators. Estimated costs for the most common major items of underground materials and supplies are presented in the accompanying tables. They represent current costs or cost ranges and are intended to be used only as a guide when preparing budgetary estimates for materials and supplies. Cost data were obtained mainly from suppliers and manufacturers, with up to three quotations being ob¬tained for each item whenever possible. In most cases, as noted in the table footnotes, prices were based on quantities representing normal requirements for me¬dium-size mine operations. Every attempt was made to assure accuracy. However, the cost for most items, especially those with multiple sources, can deviate sig¬nificantly for various reasons such as geographical loca¬tion, current market conditions, quantities ordered, size of the customer (which could influence the ultimate quantities purchased), and the ability of the purchasing department. It is also for these reasons that the actual amount individual mines are now paying for specific items may vary from the estimated cost in the tables. The cost for specific sizes of items that do not appear in the tables often can be factored from the data pre¬sented. Costs for many items can be converted easily to a unit that sometimes is more basic, but not as com¬monly used, such as from a length to a weight unit. Other items not listed, such as repair parts for equip¬ment, will involve contact with suppliers to determine specific recommended requirements and to obtain costs for these items as related to each individual project. Costs are expressed in terms of US dollars as of 1978 unless otherwise specified. All measurements, sizes, and weights are expressed in conventional units (i.e. feet, inches, pounds) ; applicable metric conversion fac¬tors follow each table. Costs are represented for drill steel and bits; mining explosives; blasting caps; blasting supplies; ground sup¬port items; ventilation equipment; utility pipe, utility hose, and accessories; mine track and accessories; tires for underground equipment; lubricants and fuels; and miscellaneous supplies.

Jan 1, 1982

By D. Lauriski

The recent spate of catastrophic events at U.S. mines raises the question as to whether or not the mine safety and health system in the U.S. is broken. The prescriptive regulatory regime in the U.S. is not a cure-all for a broken system. Without totally dismissing the contribution of a prescriptive regulatory approach, this paper argues that safety in the U.S. mining industry would be enhanced if the nation adopted a scheme that provides a balance between specification standards and two alternatives: performance and systems-based standards. This would allow effective and flexible means to continuous health and safety performance improvement. Mine operators, regulators and politicians could then go beyond thinking that compliance alone equals strong safety by creating a proactive system that emphasizes continuous improvement. By adopting performance and systems-based standards, exemplary safety and health performers can be recognized, allowing regulators to focus their efforts on those without sound occupational safety systems and who have substandard safety performance. Mining Engineering, 2011, Vol. 63, No. 7, pp. 77-82. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

"The mining industry suffers from a number of incorrect perceptions, one of which is that it is an outdated industry that has not changed for hundreds of years. But the truth of the matter is that mining is a vibrant, highly complex industry that not only employs highly skilled and educated professionals but is also often on the cutting edge of technology. It is an industry with projects that are ever-evolving and among the most challenging engineering feats in the world.Take for instance the U.S. 53 Highway Relocation project in Virginia, MN. While more of a civil engineering job than a traditional mining project, it is still a complex engineering challenge taking place in a mining environment that has called on the skills of eight state agencies, three federal agencies, a host of contractors and many consultants, including many from the local mining industry in the Iron Range of Minnesota.In 1960, the Minnesota Department of Transportation (MnDOT) constructed U.S, Highway 53 on a private easement owned by US Steel that cut across a massive taconite deposit. MnDOT constructed the highway with the agreement that if the highway needed to be moved to access the taconite deposit before 1987, US Steel would foot the bill. And if the move was required after 1987, the responsibility would fall to MnDOT. In 2010, MnDOT received the notice that the highway would have to move as property owner United Taconite planned to access the ore, setting in motion one of the greatest engineering challenges, and the highest risk project, in the history of the states’ transportation department.Pat Huston, U.S. Highway 53 Relocation project manager, opened the 90th SME Minnesota Section Conference in Duluth, MN on April 19 with a presentation about the project that includes 5 km (3.2 miles) of fourlane highway and a new 345-m (1,132-ft) bridge that will be the tallest in Minnesota when it is completed later this year.“This project was not business as usual,” Huston told the packed crowd. “Highway 53 connects Canada and the Iron Range to Duluth and Lake Superior. It is an important highway.”During his presentation he spoke about many topics that were familiar to the more than 1,100 mining professionals who attended the conference. In his keynote speech,"

Jan 6, 2017

By M. Ramokhothoane, S. Rupprecht

"NTRODUCTION Women employment in the mining industry dates back to the 19th century. Various parts of the world, for example, India, Japan, the United Kingdom and the United States of America had women employed in large numbers. The women’s jobs were primarily manual in nature. Women were used to carry coal in buckets from the coal face and out the mine, and those who worked on the surface plants were used to sort waste rock from the coal product. Other heavy industries, which were traditionally male dominated, for example the military, also had a considerable number of women supporting the war effort. The outbreak of war also caused a shortage of labour, which in turn, necessitated that women were used in various roles during the war. After World War II, women returned to their traditional roles, but had acquired new skills, and had a different outlook to life. The wearing of pants and short hair became fashionable, as a result of being in the army.Various laws were passed which prevented the employment of women underground. Different countries had rules that they believed were in the best interest of women and were of the opinion that the rules somehow were protecting women against the harsh working conditions. In South Africa, post 1994, there has been a shift in thinking in regard to the employment of women in the mines. WOMEN IN SOUTH AFRICA MINING In the words of the Minister of Women in the Presidency, Minister Susan Shabangu, “women must take centre [sic] stage as the country gears itself for the implementation of radical socio-economic transformation policies and programmes in the next five years” (SA Government News Agency, 2014). In as much as some progress has been made in advancing women, more needs to be done in order to realize sustainable benefits in the economy. The emancipation of women is a reality and remains top of the South African government agenda. From the Authors’ experience there are two types of men in the mines. The first group support change and see the value in it. To them, women in mining bring in the diversity and play the complementary role in achieving greatness. There is no fear of job security and humiliation but a great sense of “camaraderie”. The other group continues to enforce stereotypes, which works against the spirit of redressing the imbalances of the past."

Jan 1, 2018

By MOHAMMED AMINE BELMI, ANAS DRIOUCH, ABDELAZIZ LAHMILI, LATIFA OUADIF

The mineral industry uses significant amounts of water in processing. Thus, sustainable practices with the processing of ores are of critical importance. An impact tester was used to measure the adhesion force between particles and a glass disk [1,2]. A removal force was caused by the impact of the disk/particle containing a puck with a stopper. Johnson-Kendall-Roberts (JKR) theory [3] was used to determine the interfacial energy between the particles and the substrate. Capillary condensation of water can occur between the particle and surfaces in humid environments. The adhesion of particles on rough surfaces has been studied previously [4-10]. The research presented herein combines both variables to separate particle types with minimal water usage.

By S. Thibeault, P. Filiatreault, B. Straight, D. Castendyk, L. Cameron

"Unmanned aerial vehicles (UAV), or drones, capable of collecting and retrieving water samples from pit lakes, tailings ponds and other mine water basins will revolutionize environmental programs by lowering sampling costs and reducing safety related risks. Costs typically include a boat and associated equipment, boat transportation, road maintenance, water safety devices, water safety training, and additional staff. Typically, the total cost can exceed $20,000 USD per sampling event (excluding lab analyses). Hazards include potential for drowning, unstable pit walls, and unconsolidated sediment surrounding tailings ponds. Hatch has developed a novel device for aerial drones which currently enables the collection of water samples from depths up to 390 ft (119 m). This system only requires a pilot, a sample technician, and a safe operations point overlooking the water body. Hatch anticipates this will reduce monitoring cost by at least 50% while improving safety, reducing staffing requirements and accelerating data acquisition. This manuscript demonstrates profiling and sample collection from a 95 ft (29 m) deep reservoir and a 377 ft (115 m) deep pit lake, and highlights the potential of this emerging technology. INTRODUCTION Working on or near water at active, closed, or abandoned mine sites is inherently dangerous. Between 1996 and 1999, the United States Mine Safety and Health Administration (MSHA) reported 17 fatalities involving drowning at US metal, non-metal, and coal mines (MSHA, 2000). Open pit mines which fill with water following mine closure, called pit lakes, present numerous risks to environmental monitoring teams including drowning, hypothermia, falls to the ground from the top of high walls, and rock avalanches resulting from steep, unstable pit walls. Some pit lakes are simply not easily accessible for ongoing monitoring. However, the routine collection of water samples from the entire water column on at least an annual basis is required to monitor the evolution of water quality over time, to verify the accuracy of numerical predictions, and to manage lake water chemistry in order to produce “treatable” influent to water treatment plants, and ultimately, produce acceptable site discharge water quality. As a product of these risks and the need for water sample, mining companies spend considerable expense on pit lake safety as part of monitoring. This includes training personnel for “on water” duties and hazards, purchasing or hiring specialized equipment and personnel (such as boats, boat operators, personal floatation devices, and mustang suits), stabilizing pit walls and maintaining safe access roads to the lake surface, employing spotters with direct communication to emergency medical services to watch sampling activities (because cell phones and radio signals can be blocked by pit walls), and utilizing redundancy to prepare for unexpected incidents and accidents. For example, one Canadian mining company requires pit lake water samplers to hold Marine Emergency Duties (MED) training to ensure the entire boat crew is sufficient and competent for the safe operation of the vessel, and uses three boats for water sampling: two on the water at all times, and one on the shoreline, ready to deploy. The costs of these safety mechanisms greatly adds to the overall expense associated with pit lake sampling. Consequently, environmental programs may need to reduce the frequency of pit lake sampling in order to keep monitoring programs within an acceptable budget"

Jan 1, 2017

By Rambabu Pothina, Rajive Ganguli

The economics of a mineral-processing circuit is dependent on the numerous sensors that are critical to optimization and control systems. When a sensor goes off calibration, it results in errors that can have a severe impact on plant economics. Classical statistical approaches fail to detect when errors are “subtle,” unless they grow and become large enough to be “gross,” whereas methods based on signal processing and artificial intelligence fail in dealing with the complexity of process fluctuations. Due to the sheer volume of sensors, undetected errors are not remedied until the next calibration, which on average are a year apart across all industries [1]. This research aims to detect such subtle errors (2 percent bias) in shorter time spans of about a month — rather than wait for errors to grow — using innovative data-mining techniques and algorithms.

By J. Stowe

"While there has been continual improvement in the models for predicting deposition velocity and pipeline friction losses, the fundamental design philosophy for tailings pipelines has remained the same over the previous three or four decades: design the tailings pipeline to operate in turbulent flow without a deposit on the pipe invert for all expected process conditions. Recent improvements in the understanding of slurry pipeline flows allows for the design of pipelines operating with a deposit on the pipe invert, allowing the system to operate at moderate velocities for high flow rates, optimizing system energy requirements and maximizing pipeline wear life.Tailings pipelines are increasingly operated at higher solids concentrations when there is a greater likelihood the pipeline will operate in laminar flow due to the higher tailings slurry rheology. Historically, slurry pipelines have been operated in turbulent flow. We now know that laminar-flow pipeline operation is possible as there are several operational laminar-flow tailings pipelines. While our understanding of laminar-flow slurry pipelines is not complete, recent research provides guidance on how to approach the design of these pipelines.New sensor technology has led to the development of an instrument that provides reliable indication of bed-deposit height within a pipeline. This technology is particularly helpful in operating pipelines with a deposit and has application in better understanding the operation of laminar-flow pipelines. Failure of tailings pipelines can result in consequent damage to surrounding structures and unacceptable spillage into the environment. Modern pipeline leak detection technology allows operators to better manage this risk by ensuring safe and reliable operation of tailings pipelines.This article provides an overview of the each of the above advances in the design and operation of tailings pipelines.Operating tailings pipelines with a depositTailings pipelines, and slurry pipelines in general, are typically designed to operate without a deposit on the pipeline invert. Meaning, the minimum operating velocity exceeds the turbulent deposition velocity. This approach has been adopted due to concerns regarding potential blockage of a pipeline operating with a deposit."

Jun 1, 2019

By J. M. Wempen, R. D. WEYHER, M. K. McCarter

Beam theory is a proxy for the behavior of intact, deforming roof strata above underground openings. Strong, stiff, intact strata have the ability to store significant strain energy when underground openings have large spans, as is typical of longwall operations. When strata fail, they may release some or all of this strain energy. Released energy is partitioned between fracture, thermal and seismic energy. The tensile failure surface in simply supported beams is predicted to be free of shear stress. This prediction and the kinematic inability of crack slip during fracture make significant dissipation of energy by friction unlikely.  In this study, the failure energy partitioning of specimens from the Nugget Sandstone formation is examined. Tensile fractures in specimens were induced using three-point loading tests. Elastic waves emanating from fracture events were recorded using an array of accelerometers. Accelerometers were placed within two crack lengths of the fracture surface, and the acceleration records are similar to strong motion seismic records. Spectral analysis was performed and used to develop synthetic, well-behaved, acceleration signals. Synthetic velocity signals were used to estimate radiated seismic energy generated by fracture. These estimates of radiated seismic energy demonstrate a potential means to constrain the minimum seismic partition. Fracture testing was performed on additional samples to estimate the fracture toughness of the sandstone. Synthesis of this data demonstrates a potential means to constrain a maximum seismic partition. Bounding the seismic partition for this type of fracture event could aid the detection and evaluation of seismicity emanating from longwall operations. Having better information about the location and magnitude of mining induced seismicity within longwall overburdens could lead to better understanding of extraction sequencing and rock behavior in general. These energy estimates also support the hypothesis that dissipation of thermal energy by friction is small in bending tensile failure.

By David M. Abbott

"The picture of the baby surrounded by the number of (usually) pounds of a variety of mineral products a newborn will use in a lifetime has been widely distributed over the years, both on the web and as business cards that could be distributed to anyone. Figure 1 shows a typical example. I have included a slide of the mineral baby in various lectures over the years, particularly in my lecture “Industrial minerals: much used, little recognized.” The mineral baby with associated estimated lifetime mineral quantities is updated every year. I collected a set of past mineral baby pictures to examine the changes in the quantities of the various mineral products over the years.The mineral baby was introduced by the Minerals Information Institute (MII) in 1999 and became known as the “MII Baby.” SME took over MII in 2008 and continued publication as the “MII Baby” until the merger of MII with SME’s GEM program in 2011 to form SME’s Minerals Education Coalition (MEC). MEC is now the publisher. Figure 2 is the 2016 version of the mineral baby. The repositioning of the picture of the baby from lying on its back to crawling reflects a major design change to help emphasize that SME’s MEC is now the mineral baby’s publisher.Data sourcesThe data used to prepare each year’s mineral baby comes from the National Mining Association, which collects the preliminary annual mineral commodity data from the U.S. Geological Survey (USGS) and other sources. This preliminary data becomes available late in the first half of each year. The life expectancy data for each year comes from the Center for Disease Control’s “Data and Statistics by Topic” and the population data comes from the U.S. Census Bureau’s “Quick Facts” tab.The source mineral data is compiled using metric tonnes as the basic unit. The quantity of of each mineral is the apparent U.S. consumption each year."

Jan 6, 2017

By R. Zins

During the past few years, a completely new concept has been applied to the design of drives for operating at very low speeds. In this, the motor is supplied by a variable-frequency thyristor cyclo-converter. Today, frequency converters with practically unlimited power ratings can be constructed. The system frequency of 50 or 60 Hz is reduced to about 10 % of these values. This makes it possible to operate the synchronous motor, which has a correspondingly high number of poles, at the extremely low speed of the driven mill, i.e, without interposed gearing. The first motors of this type were built to drive ball mills in the cement industry, which are very similar to those employed for ore processing. Here, too, the tendency is to build units of ever increasing capacity. In the case of conventional drives with mechanical gearing, this involves correspondingly increasing difficulties. These difficulties have prompted various studies of the possibility of applying the new type of drive to ore mills as well, but a gearless drive has not yet been built for this application. However, gearless drives for ore mills will certainly materialize soon and it was therefore considered a logical step to report at the A.I.M.E. Conference on the experience gained with these drives in the cement industry, and on the present state of development.

Jan 1, 1973

By Hooman Askari-Nasab, AHLAM MAREMI, EUGENE BEN-AWUAH

In oil sands mining, tailings are voluminous unwanted byproducts generated from extracting the desired mineral from the mined ore. Dyke construction and backfilling activities require well-managed techniques to facilitate progressive reclamation at the earliest opportunity. This directly affects the sustainability and profitability of the mining operation. This research introduces a goal programming framework that simultaneously optimizes the (1) production schedule with limited duration stockpiling and directional mining, (2) dyke construction schedule, (3) size, shape and location of tailing cells and (4) mining and processing production targets. The results show that in creating in-pit tailing-cell designs, decreasing the mining-cell volume and increasing the number of mining cells improves the net present value (NPV) of the operation due to increased operational flexibility.

By Alten F. Grandt

Surface mining consists of the removal of the geologic strata overlying the coal seam usually with large electric shovels, draglines or bucket wheels. The method produces more or less parallel ridges or peaks of cast overburden, usually called "spoil banks". The mined lands vary widely in their inherent characteristics to produce a vegetative cover and thus can be put to a wide variety of uses. Use is the key to economic and social benefits. Physical and Chemical Characteristics of Soil Material of Surface Mined Lands after surface mining operations, the soil material is a heterogeneous mass whose physical and chemical properties are dominated by the character of the geologic strata overlying the coal. These strata are highly variable in thickness and character. They may include the surface soil, loess, glacial till, sands, shales, slates, limestone and sandstone rock. The method of mining with the several types of mining equipment will also affect the resultant mined area.

Jan 1, 1968

By J. J. Antony

The Cactus Gold Mine is a joint venture comprised of Middle Buttes Partners Ltd. (CoCa Mines, Inc.--operator, T. Congdon and W. Carey) and Compass Mining, Inc. The project includes 2.4 sq. miles of contiguous mining claims and leases in the Mojave Mining District, Kern County, California, approximately B5 miles northeast of Los Angeles. The property is readily accessible year round by all-weather roads and is within 6 miles of the main line of the Southern Pacific Railway.

Jan 1, 1988

By Anthony Iannacchione, Tim Miller, Nicole Evanek

The Subtropolis Mine is a room-and-pillar mine extracting the Vanport Limestone near Petersburg, OH. In February 2018, mine management began implementing a new mine layout to better control the negative effects of excessive levels of horizontal stress. Almost immediately, the conditions in the headings improved. Conversely, and as expected, stress-related damage was concentrated within crosscuts. Over the last 18 months, the mine operator has diligently experimented with different techniques/methods to lessen the impact of the instabilities in the outby crosscuts. The range of controls used by the mine operator include angled crosscuts, crosscut offsets, increased distance between crosscuts, arched crosscuts, cable-bolted crosscuts, altered blasting pattern, and windows. A window is used to resist roof deformation by leaving a strong brow of roof rock within the crosscuts.

By Ulrich Benatzky

Rheinbraun AG, Germany, is the management company of the mining and raw materials division of RWE AG. Rheinbraun's core business and major functional area is opencast lignite mining in the Rhineland. The characteristic feature of opencast mining is continuous operation using bucket-wheel excavators, belt conveyors, and spreaders. The report gives a survey of the conveyor systems used. In addition to the general performance data of these belt conveyors, this report will deal in particular with major components, such as drive stations and individual mechanical components (e.g., conveyor belts, pulleys, gears, couplings, brakes, scrapers), as well as monitoring systems. Finally, an assessment of the conveyor systems, together with future developments, will be given.

Jan 1, 2000

Newmont Mining Corp. has been producing gold from the Carlin Trend for more than 45 years. Naturally, the focus, scale and complexity of the operations have changed considerably during this time. Newmont discovered and developed the Carlin Main orebody that is located about 32 km (20 miles) north of Carlin, NV. The property was developed as a one-mine, one-gold mill treatment plant operation, which produced about 6.2 t/a (200,000 oz/year) of doré gold bars. The initial mine, mill and gold refining facilities were relatively small in comparison to today?s standards. The milling circuit used the Merrill-Crowe zinc precipitation process to recover dissolved gold and prepare a concentrated precious metal ?precipitate? to be melted into a doré bar for sale.

Jan 1, 2012

By Jenna Wundrack, Evan Thibaud

The advanced cryogenic treatment is a post-manufacturing metallurgical process that involves subjecting off-theshelf materials to extremely low temperatures, significantly improving wear resistance and reliability. These case studies explore whether the claims of Enrich Bits & Tools benefit metals and their specific in-field application to drill bits in the blasting industry. This paper reviews the application of the treatment to button drill bits for enhanced wear resistance in two operations. The first is a civil construction project with highly abrasive rock. To confirm the remarkable benefits of the treatment, a second case study was performed. This case study utilized measure-while-drilling technology in consistent rock characteristics to reduce variables in the field study.

Feb 1, 2024

By Ebelia Manda, Peter RK Chileshe, Sydney Chinyanta, Abdul Samson, Victor Mwango Bowa

Buttressing is a widely employed control measure for mitigating slope failure in various settings such as openpit mines, road sections, dams, and hilly or rocky terrains. This paper presents a study on the effects of buttressing, specifically concerning slide-head toppling failure. Drawing insights from a case study of slide-head toppling in Zambia, our investigation employs both analytical (limit equilibrium) and numerical (3DEC software) modeling techniques. The analytical and numerical models exhibit notable similarities in their schematics and overall results, revealing a subtle effect of buttressing in controlling slide-head toppling failure. This study contributes valuable insights into the nuanced role of buttressing in slope stability, with implications for optimizing buttress design parameters. While the overall findings suggest a modest influence of buttressing on slide-head toppling failure, further discussions delve into the specific implications and potential refinements for practical applications.

Jan 1, 2025