Search Documents

By Fikret Suner

Two rare evaporite minerals, nahcolite (NaHC03) and trona (Na2C03?NaHC03?2H20), are both widely used in the production of sodium carbonate (Na2CO3) The largest natural carbonate deposits (trona) are in Wyoming, USA, the second largest deposits are in Turkey, in a lacustrine basin (Beypazari) where nahcolite and trona are located within the Miocene Hirka Formation. The Hirka Formation is mainly composed of bituminous shale, claystone, marlstone, tuffltuffite, and dolomitic limestones. Although numerous trona beds are interbedded within the above mentioned sedimentary units, there are only two beds of trona that are of economic interest. The lower part of the lower trona bed is rich in double carbonates such as pirrsonite (NA2C03? CaC03?2H20) and gaylussite (Na2C03?CaC03?5H20), indicating a change in Ca/Na ratio in the solutions which are responsible for the formation of soda occurrences. In contrast, the upper part of the upper trona bed is rich in nahcolite. This minerological pattern has been found in every drill- hole in the basin. While both trona beds average up to 10 m (33 ft) thick, the average thickness of nahcolite is approximately 0.5 m (1.6 ft). Also, thin section studies show that many fibrous and lath-like trona crystals contain small radial nahcolite crystals; all of them are euhedral and equi-dimensional. Geochemical studies of major, minor, and trace element contents also support this coexistence. Macroscopic and microscopic observations reveal that the nahcolites principally were formed as a result of an incongruent dissolution process of trona. In conclusion, the presence of nahcolite in the Beypazari basin is due to the dissolution process of trona, particularly during the last stage of evaporation, as a result of fresh water entering the basin. During that time, an increase in the HC03/ C03 ratio resulted in nahcolite-trona phase transitions.

Jan 1, 2001

By V. O. Tenorio, A. M. Sanzana

"INTRODUCTION This report summarizes a research about mines which are transitioning from surface to underground mines. It is a guide to make strategic decision in these increasing amount of mines. Capital and operating costs are linked with major strategic decisions in the exploitation of an ore body. This is the reason to analyze costs related to this transitioning world trend. There are multiple reasons for transitioning from Open-Pit (OP) to Underground (UG) mining. The primary economic incentive for going UG is that the cost per unit of ore from OP mining eventually exceeds that from UG extraction. This is due to the excessive amount of waste that must be extracted when the depth of the pit increases. In addition, the reduced footprint of UG operations contributes to diminish the environmental impact on the surface. Furthermore, it becomes more difficult to find new, easily accessible ore deposits. Then, a cost model helps to guide strategic decisions in the transition from OP-to-UG mines. Objectives • Propose a methodology to guide strategic decisions in the transition from OP to UG mining. • Create an integrated cost model based on existing OP and UG individual cases. • Identify and characterize a group of mines transitioning from OP to UG. • Analyze operating and capital costs of a particular transitioning from OP to UG mine. MAIN CONCEPTS Open Pit Mining (OP) The main decisions in OP mines are: Cut-off grade, Stripping Ratio (SR), equipment size, stockpiling, pushback sequencing and processing capacity. The stripping ratio is measured as the tonnage of waste required to be removed to reach and extract one tonne of ore. The material extracted from an OP exploitation can be classified as waste and ore. This classification depends on the cut-off grade. The cut-off grade indicates the minimum amount of material with economic value in a block. The waste from the mine is going to the waste dump and the ore is going to stockpiles where will be store and then going to the processing plant (leaching or concentrator). The waste of this process is going to the tailing pond big pools. And the product is sell in the market. Another important issue is the mining capacity which is going to define the investment in mining equipment. Underground Mining (UG) The first decision to be made in order to open an underground mine is selecting the mining method. Caving methods are the more productive and have lower operating costs. There are three caving methods: Block Caving (BC), Panel Caving (BC) and Sublevel Caving (BC). The access development could be an horizontal adit or a straight or downspiral decline. A shaft could be used for inclined or vertical access. Other key issues are: equipment capacity, cut-off grade and production sequencing."

Jan 1, 2016

By R. E. Turner

Hamersley Iron Pty. Limited, one of the world's largest iron ore producers, operates a 3.0 million tonne per year pelletizing facility at Dampier in Western Australia. The plant produces pellets for the export market using a blend of natural hematite fines from the Company's two mines at Tom Price and Paraburdoo. Processing includes fluidised-bed drying of the ore feed, open circuit dry grinding, disc balling and pellet induration in a travelling grate furnace of Dravo-Lurgi design.

Jan 1, 1980

By Peter B. Dowden, David T. Cass

A shield on a tunneling machine has two basic purposes. Firstly to provide temporary support in unstable ground, maintaining the integrity of the bore and protecting the operators, and secondly, in conjunction with other sealing devices, to prevent the ingress of water. In any specific tunnel, unstable ground and water may or may not occur together. Further, there are a number of different ground behaviors that may be termed unstable and these must be defined in order to determine the most suitable type of machine. Beyond the shield itself, the cutterhead and the mucking system design are critical in successfully traversing difficult geology. In any but the shortest tunnels, variations in the geological conditions and the requirement of an acceptable advance rate can impose increasing degrees of sophistication in the machine design. In this paper we will review current designs of shielded type machines and their application, and discuss new developments which blend hard and soft ground tunneling technology. We will also indicate that in some conditions, although first impressions seem to favor a shielded machine, in fact an open gripper TBM may be the wisest choice.

Jan 1, 1991

By Slavoljub D. Maksimovic, Steve J. Page

The Bureau of Mines measured respirable dust emission rates from overburden drilling at a surface coal mine and the transport of this dust to downwind locations. The emission rates were estimated by using multiple gravimetric dust samplers mounted on a cross-shaped tripod located immediately downwind of the drill. The transport of this dust was measured at more distant downwind locations by a combination of respirable gravimetric sampling and integrated bag sampling of sulfur hexafluoride (SF6), which was used as a tracer gas. Two modes of sampling were used: (1) At five sampling locations arranged in a semicircle around the drill. The radius of this arc ranged from 15.85 m (52 ft) to 71.32 m (234 ft). (2) In-line sampling at downwind locations with samplers located at intervals of either 10.67 m (35 ft) or 15.24 m (50 ft) for a total distance of 76.20 m (250 ft). Samples were taken 1 .22 m to 1.52 m (4 to 5 ft) above ground level. Test results for the semicircular test arrangements showed that at any downwind location, the maximum contribution of respirable dust due specifically to the drilling operation was 42%; the average for eight tests was 13.6%. In general, there was no correlation between the downwind distance of this maximum contribution and the maximum contribution itself because of changing wind direction. Test results for the in-line arrangements indicated that the transport of the dust from the drilling operation usually decreases rapidly with distance and that, even though the drill dust may produce significant health hazards for the drill operator and drill helper (or other personnel in the immediate vicinity), the exposure of downwind personnel to drill-generated dust may not be a significant problem.

Jan 1, 1987

By N. Merriam

This report describes Koppelman's work to develop the K-Fuel® Series C Process used to dry and stabilize Powder River Basin coal. It also contains summaries of the results of bench-scale and pilot plant tests conducted to prove the Series C Process. The process is being used by the KFx-Thermo Ecotek partnership for a 500,000 ton per year commercial plant that has been constructed near Gillette, Wyoming. The plant is presently undergoing shakedown.

Jan 1, 1997

By Christopher Newman, Robert Dupuy, David Newman

"The development of a multiple level underground mine is a complex task in which geology, engineering, ground control, and unit operations are integrated into a single mine design. The components are inter-dependent and must function cohesively to ensure a profitable underground mining operation. To optimize reserve recovery, mine planning should begin from the lowest level and progress up. This limits any misjudgments or oversights of a given level affecting the underlying levels and ensures the ability to maximize recovery from each level.Mine planning should start with the exploration and characterization of the geologic setting. Once the reserve geology and quality is well understood, then mine planning can begin with respect to the following:,Orientation of mine works with respect to horizontal stress,,Access to the reserve,,Determination of opening widths,,Selection of back, floor horizons and pillar centers,,Selection of development and secondary mining heights,,Appropriate interburden thicknesses, and,Examine the stability of the multiple level mine through numer¬ical modeling.The multiple level mine design process and decisions are presented through a case history example. The theme is that there is one opportunity to “get it right” as well as many chances to overlook a small aspect within the design that will plague the mine throughout all levels and through the entirety of its operating life.INTRODUCTIONAs surface quarries reach their economic stripping limit and encroach on mineral and/or reserve boundaries, they approach the end of surface mineable reserves. Furthermore, modern urban sprawl has placed previously remote surface quarries within suburban development and neighborhoods, leading to significant increases in noise, dust, and vibration grievances by the community and regulators (Newman, 2017). Many mining operations have begun year-round production of underground reserves to meet growing market demands. This does not permit the typical sequence of stripping overburden in the winter to provide limestone to mine during the construction season. Underground stone mining operations in the United States commonly utilize a room-and-pillar mine layout with drill-and-blast production methodology for the development of the reserve. Within the Midwest and Eastern regions, thick and flat-lying limestone formations lend themselves to the utilization of multiple level mining layouts. While a multiple level mine plan will increase the overall recovery of the reserve, greater overburden depths, multiple level geometry, and the presence of discontinuities all require an emphasis on ground control for the planning and development of a safe and productive multiple level underground stone operation."

Jan 1, 2019

By M. C. Manderson

Phosphate rock is a naturally occurring mineral which, in upgraded form, is important to both agriculture and industry. Phosphate rock normally must be upgraded before it can be assimilated and used. Most of this upgrading is now carried out by chemical means, largely through the reaction of a strong inorganic acid (primarily sulfuric acid) with the phosphate rock to remove major impurities and to produce soluble phosphate. A less important but yet still commercially significant conversion method involves the thermal reduction of phosphate rock at high temperature in an electric furnace to produce elemental phosphorus. The elemental phosphorus is then converted to usable end products. This conversion route is a more costly method than the chemical route, but it has the advantage of being able to produce chemically pure phosphorus derivatives. On the other hand, the use of phosphate rock for agricultural application-primarily for use as a plant nutrient ingredient for fertilizer -does not require the same level of purity. As a consequence, the chemical method of phosphate rock upgrading is the predominant technique for producing phosphatic fertilizers.

Jan 1, 1977

By D. C. Rotherham

The Kidston gold discoveries were originally made about 1907, and by 1934, 1.76 Mg (62,000 oz) of gold had been produced from placer and lode mining of higher grade, most¬ly oxidized gold ore. As mining in the lode ore penetrated deeper, costs increased and the world gold price stagnated. The lode or underground production averaged close to 6.9 g/t (0.2 oz per ton) Au for the 201 kt mined. No mining or development took place from 1934 until 1965. Kidston's high grade ores were exhausted by 1934. From 1965 to 1976, exploration had developed 3 Mt of about 3 g/t (0.88 oz per ton) Au. Placer Pacific acquired rights to the property in 1976 and began a geologic and engineering study of the district. It was clear that the deposit had the potential for becom¬ing a large-tonnage, low-grade producer. However, explora¬tion had to discover the tonnage and grade and engineering needed to solve the obstacles of production costs. Bulk material handling problems were addressed by Placer's wide experience in open pit mining, and the increase in work index accompanying deeper ores was handled by Placer's metallurgists. The matter of power for the operation was solved by engineering studies. These showed that power could be generated and brought in economically. The price of gold also increased after 1976, and this helped in the economic analysis. The Kidston discovery since 1976 is really a combination of good exploration geology and careful engineering plan¬ning that overcame the obstacles presented by ore characteris¬tics and the location of the deposit. The attached paper by Harry Mustard is an extract of his honors thesis and explains the deposit geology.

Jan 1, 1990

By Tony Dunn

FMC Corp. achieved a significant cost reduction at its Green River, WY soda ash operations using a new proprietary solution-mining and processing technology. In phase one of the program, trona ore is dissolved, recovered and processed with the new technology. It is then fed into an existing refining plant, replacing dry mined and calcined trona ore. Phase two produces a final high-purity product. It also increases capacity by 635 kt/a (700,000 stpy). Both phases were completed under budget and ahead of schedule. This $120-million expansion project uses a new process and a new team to derive soda ash in a more cost-effective and environmentally friendly manner. The team successfully introduced solution-mining technology - with a liquid solution injected into previously mined sections of the mine. This shift in techniques signified a new era for soda ash production. The project is an example of teamwork at its best. For it to be successful, FMC had to work within several different areas inside and outside of the company. Engineers, contractors, mechanical operators and technical people were needed who could blend in with FMC's existing in-house team.

Jan 1, 1999

By Ruiren Jin

In alkaline pulp, galena is depressed by sodium carboxymethyl cellulose (NaCMC), while Cu(II)-activated sphalerite exhibits a high flotability so that satisfied separation can be achieved. In addition to hydrogen bonding, chemical bonding of NaCMC with galena is confirmed by IR; only hydrogen bonding is involved between NaCMC and Cu(II)-activated sphalerite. It is also found that the greater the degree of substitute and polymerization of NaCMC, the stronger the depressive effect of NaCMC and that lower stirring speed favors the depression.

Jan 1, 1987

By Deepak Malhotra, William F. Riggs, Edward C. Dowling

INTRODUCTION Mining companies are In the business of making an acceptable profit on their Investments, It became obvious in the recent recession that economic profitability/viability depends on being the lowest cost producer In order to compete on a global basis. The burden of achieving this objective falls on the mineral manager. He must strive to produce a salable product in an environmentally acceptable process while continuously Improving the profit margln.(1,2) Metal prices fluctuate on a regular basis. They directly Impact revenue and hence operating philosophy. The mineral engineer needs to develop an optimum operating strategy to meet his overall objectives, One would expect that, In the modem era of complex computer models, it would be easy to develop an economic model to maximize profits and/or cash flow. Discussions with mill managers Indicate that one mine/corporation's optimum operating strategy is not necessarily optimum for another. This paper approaches the problems from basics "Economics 101" and Illustrates the complexity of developing a universal model which can be applicable to all mines. Case examples are used to illustrate the need for better communication to avoid the basic economic fallacy “that optimization of segments leads to optimization of the whole system.” TECHNICAL MODELS Technical models are a prerequisite to the development of economic models because they provide the necessary Input data to these models, The flow of material from a mine through the sale of the finished product is shown In Figure 1. The ore Is mined and milled, and the concentrate can be stored for sale or smelted and refined In-house or at a toll facility. The finished product(s) are held In Inventory until sold either through existing contracts or in the spot market. [ ] Fairly reliable technical models have been developed for mining, milling and smelter operations. Mine plans are developed to provide a good Indication of the relationship between production and cut-off grade. It is easier to change surface mine plans than plans for underground mines. However, there are limits to maximum production that can be achieved with existing equipment. It Is possible that mine benches may not be developed to handle additional equipment, even If It was purchased to enhance production. More often than not, the cut-off grade Is lowered to Increase throughput goals.

Jan 1, 1993

By S. G. Ozkan

Boron minerals of economic importance are primarily colemanite, tincal, and ulexite. Turkey and the United States are the leading producers of boron minerals and compounds. Other production includes datolite in Russia and synthetic colemanite in Chile. This paper will discuss various types of chemical and physical treatments of boron ores to produce the marketable minerals and compounds that are consumed in commercial products.

Jan 1, 1995

By J. A. Marts, R. C. Gilmore, S. Saki, J. F. Brune

El modelamiento de la dinámica de fluidos computacional (CFD por sus siglas en inglés) implica la creación de un dominio de cálculo llamado malla o rejilla para resolver las ecuaciones que definen la física del flujo de fluidos. Este proceso comprende a menudo emplear la mayor parte del tiempo en esfuerzos de modelamiento. En un proyecto patrocinado por el Instituto Nacional de Seguridad y Salud Ocupacional (NIOSH), los investigadores de la Escuela de Minas de Colorado utilizaron un enfoque innovador de mallas, el cual permite una fácil adaptación del modelo CFD para adaptarse a una variedad de geometrías de minado de tajos largos ventilados por canales (bleeders) y progresivamente sellados (referidos a menudo como bleederless en los Estados Unidos), con la porosidad y la permeabilidad de la cámara escalables en un amplio intervalo. En este trabajo se presenta la metodología del enfoque de enmallado y escalado junto con las recomendaciones para el uso de modelos CFD en aplicaciones de ventilación para las cámaras en tajos largos. La nueva técnica de enmallado se utilizó para evaluar la función de un retorno hacia atrás en una cámara progresivamente sellada y otra cámara ventilada por canales.

Jan 1, 2014

By T. P. Weldum, W. Conger

"The objective of the study conducted by the authors is to determine what media size(s) addition will maximize any given plant ball mill’s grinding efficiency (Fig. 1). The functional performance parameters “mill grinding rate through the size of interest,” and “cumulative mill grinding rates” from both plant and smallscale tests are applied to this task. A plant media sizing methodology, and industrial case studies, are provided.BackgroundA previous article (“Ball mill classification system optimization through functional performance modeling,” Nov. 17, McIvor et al., 2017, Mining Engineering) described circuit classification system efficiency (CSE), equal to the percentage of coarse (plus circuit P80 target size) material in the ball mill. It can be measured and then increased through pump and cyclone adjustments. By so transferring the application of ball mill power from fine (minus P80 product size) to coarse material, circuit efficiency is increased and overgrinding is decreased.The other factor that determines overall circuit efficiency is how well the power that is applied to the coarse material grinds it. This is affected by design and operating variables like the media sizing and mill percent solids. From circuit functional performance (McIvor et al., 1990):Circuit production rate of new fine material (t/h) = Power applied to coarse material (kW) x Mill grinding rate of coarse material (t/kWh) (1)The power applied to coarse material is the total mill power multiplied by the CSE. Therefore:Circuit production rate of new fine material (t/h) = Total mill power (kW) x CSE (%) x Mill grinding rate of coarse material (t/kWh) (2) Production rate, mill power and CSE can be measured during a plant circuit survey. The mill grinding rate of coarse material is then calculated. At the circuit target P80 size, this is the mill grinding rate (of coarse material) through the size of interest. The objective is to maximize this rate. The mill grinding efficiency can also be calculated by taking the ratio of the mill grinding rate over the material’s grindability as measured in the lab. Mill percent solids optimization has thusly been achieved (McIvor et al., 2000). For media sizing, maximizing the mill grinding rate on a given ore is equivalent to maximizing the mill grinding efficiency. Ores of different grindability will be part of the discussion."

Jan 11, 2018

By F. M. Doyle, Robert G. Robins, E. Peters

Stability diagrams for the Cu-S-H2O system have been widely applied over many years. Stability diagrams for aqueous systems generally, have been generated by computer, but with the programs for Potential-pH diagrams in particular, a common routine leads to error in multi-element systems. In this paper these errors, and some misinterpretation of diagrams are considered. In most of the published diagrams for the Cu-S-H2O system there has been no account of the sulfide complexes of copper. Here, the free energies of formation for the various species in the system have been re-evaluated for consistency, and some diagrams for the Cu-S-H2O system ( generated with the program DIASTAB Vers.5 ) are presented.

Jan 1, 1993

By D. S. Choi

The paper presents the result of analysis of subsidence data collected from coal mines operating in Northern West Virginia and Southwestern Pennsylvania. A particular emphasis la placed on the measurement of the angle of draw for the protection of surface structures.

Jan 1, 1986

By Ataç Başçetin, Hasan Çelt, Hüseyin Onur Dönmez, Kürşat Hasözdemir

Phenolic foams, known for fire resistance, show broader industrial potential, particularly in mining, through property enhancements. Adjustments to the formaldehyde-to-phenol (F/P) ratio, bio-based additives like lignin, and nano-silica improve foam strength and thermal stability. Density modifications allow foams to range from flexible, low-density forms to rigid, high-density supports. In mining, enhanced phenolic foams could reduce coal ignition risks by acting as oxygen-blocking barriers. Current findings suggest these foams offer viable, sustainable solutions for safety in hazardous environments. Continued development could make them essential for thermal and mechanical applications under extreme conditions. This paper aims to provide a comprehensive overview of the mechanical characteristics of phenolic foams, current enhancement strategies, and standardized testing methods used to evaluate foam properties.

Feb 1, 2025

By Edward S. Frohling

Va a ser discutida la información que se requiere para un estudio preliminar de viabilidad y la información adicional que se requiere para el estudio final de viabilidad de un nuevo depósito de mineral. El estudio preliminar de viabilidad se realiza con muy poca información y con un mínimo coste para el propietario. Sin embargo, el diseno del informe preliminar es similar al utilizado para el informe final. En este momento, se supone que el resultado del estudio preliminar es favorable y el propietario autoriza el estudio final de viabilidad a una compañía de ingeniería. Se describirá el tipo de organización para completar el estudio final de viabilidad. El informe final incluirá toda la información y datos relativos al nuevo depósito de mineral. La información presentada debe ser entendida lo mismo por el personal financiero que por el técnico.

Jan 1, 1982

By R. O. Y. Breese

Perlite is a hydrated acid volcanic glass that has been derived from the alteration of obsidians through incorporation of water into the silica structure. It is distinguished from other members of the water-bearing natural glass family by total water content, characteristic fracture and luster. The distribution of major occurrences worldwide is associated with silicic Tertiary through early-mid Quaternary volcanics related to plate movement. The No Agua dome and flow complex is one of the most highly studied perlite occurrences in the world. It clearly exhibits lithologic and textural zonations that reflect simple cooling history. Similar features are commonly observed within other perlitized, extrusive glass selvages. This paper briefly discusses current thought regarding geologic occurrence, the hydration process and the modes of origin with special emphasis on No Agua.

Jan 1, 1985