Search Documents

By Zoheir Khademian, Gabriel S. Esterhuizen, Morgan Sears

Based on the 2010-2019 Mine Safety and Health Administration (MSHA) accident report database, 91% of reported ground control accident in the US longwall mines were caused by gateroad roof instability. This can be related to the significant changes in loading conditions that gateroads are subject to from the development to the longwall abutment loading phases, combined with the thinly bedded shale roof, found in many US longwall coal mines. One of the challenges in designing efficient support systems is to understand the roof instability mechanisms along with support-roof interactions under this complex loading condition. Field monitoring of roof displacement and stress changes coupled with detailed analyses using numerical models are well-documented techniques to study the causes of roof instabilities. However, traditional modeling techniques require additional calibration to simulate delamination and buckling of shale roof, one of the main roof instability mechanisms in longwall mines. One alternative modeling technique is the UDEC Bonded Block Method (BBM) where bedded roof and support interactions can be explicitly captured. This paper presents the development of a BBM model of a longwall entry at a 180 m depth of cover with a three-entry gateroad layout along with roof extensometer monitoring results. The models are validated against the monitoring data, showing the potential for BBM numerical models capturing the complex roof and support system interactions to assist with optimizing gateroad layouts and support systems.

By M. J. DeMarco

Beginning in late 1985 and continuing through 1987, Bureau of Mines personnel investigated longwall chain pillar and entry design in two-and three-entry gate-road systems at a deep underground coal mine located in central Utah. To evaluate their respective stability characteristics, four chain pillars and two longwall panels within the two separate entry systems were instrumented with Bureau of Mines hydraulic borehole pressure cells to continuously monitor vertical and horizontal pillar and panel stresses through adjacent panel retreat. In addition, supplemental entry closure information was obtained from sites located in the vicinity of the instrumented pillars. The findings presented in this report demonstrate the practicality of evaluating mine pillar stability using in situ methods and support three significant conclusions regarding ground control aspects of the investigated two-entry system: (1) Total areal entry loading was considerably less for the two-entry system, as opposed to the three-entry system, (2) a smaller percentage of opened ground in the two-entry system contributed to a marked reduction in roof falls, and (3) lower areal loading in the two-entry system suggests improved ground conditions when mining the underlying seam.

Jan 1, 1988

By H. Dho

The role of sodium silicate in the anionic flotation of a Florida phosphate ore was investigated using laboratory continuous flotation tests, frothability tests and SEM observations. In the absence of sodium silicate, Ca++ promoted the unwanted activation of quartz by forming calcium bearing precipitates. The addition of sodium silicate enhanced the flotation efficiency through: (1) the removal of impurity minerals and calcium-bearing. precipitates from quartz surfaces by dispersion, (2) drier and more persistent froths stabilized by oily droplets containing calcium silicate precipitates, and (3) higher specific flotation rates of phosphate relative to quartz, leading to faster flotation rates and increased selectivity of separation.

Jan 1, 1990

By H. Akgun, J. J. K. Daemen

Design of plugs for abandonment of boreholes and shafts may be governed by the bond strength between the plug and host rock. Presented in this paper are the results of push-out tests on two types of expansive cement grout plugs emplaced in rock salt. The average interface shear strengths range from 2 to 12 MPa. Peak shear stresses (assuming an elastic stress distribution along the interface) are up to eight times higher. Dissolution along the interface may be enhanced by clay inclusions in the salt and appears to reduce bond strengths. Application of the results to the design of plugs for larger openings (e.g., shafts, drifts, or boreholes) is discussed.

Jan 1, 1995

By R. J. Grace

Carbon in the form of coke is used as a reactant in various chemical and metallurgical processes, The high cost of by-product coke along with its periodic lack of availability and high investment necessary for additional by-product recovery facilities indicate the need for a low-cost production unit based on a new procedure for coke manufacture, Traveling-grate coking-stokers were developed by Shawinigan Chemicals Ltd. to produce coke required for carbide manufacture, They were adapted to kilns so that the hot volatile gases could be used for lime burning, Their operation has been described in various patent disclosures (1, 2, 3), and their application to rotary lime burning kilns has been described by Andersen (4). Details of the process and plants have also been published by Kurt Baum (5,6).

Jan 1, 1958

By Mike Wardell-Johnson, Chris Campbell-Hicks, Craig Bitmead

Faster, simpler, cheaper and more accurate cyanide ex­tractable gold procedures are now available for grade control assay. Cyanide 'bulk leach extractable gold' or BLEG assays have previously been seen as desirable, due to the large sample size that can be treated, but not in common use due to the 24hr total assay time required. Sample sizes from 50g to several kilos can now be accurately assayed in less than 4 hours total time with the larger sample size increasing accuracy, without loss of precision, while greatly reducing the 'nugget effect' or coarse gold bias. Typical assay size is 200g, equivalent to 4 x 50g Fire Assays or 10 x 20g Aqua Regia Assays. Ongoing modifications and refinement of the procedures and reagents used also indicate applicability to the treatment of coarse gravity gold where substantial savings in both capital and operating costs for these circuits are possible. The successful use of this cyanide assay at the Bannockburn and Windine Well operations are cited to-gether with a compre­hensive comparative testwork program by Newcrest. Testwork at Gidgee and Lynas Gold operations is currently being initiated. Other operations using the method include Red Dome and Kidston; with Placer(Granny Smith) and PMA's Palm Springs operations to commence shortly.

Jan 1, 1995

By G. T. Adel, J. D. Miller, C. L. Lin

In view of the success of recent laboratory studies using X-ray computed tomography (CT) to determine coal washability and with the availability of high-speed CT systems, it now seems possible to design an on-stream washability system for the control of coarse coal-cleaning circuits. Design features for such a system are examined and possible control strategies are discussed for different applications.

Jan 1, 1995

By Rameshwar Sah, L. R. Singh, SIVALINGARAJU BARISETTY, SHYAM YADAV, P. K. Ghorui

Fly ash is a by-product generated from combustion of coal in thermal power plant. Disposal of fly ash is a major environmental concern for the power plants. Though a considerable part of fly ash is used in cement making and brick manufacturing, substantial quantity remains unutilized. Silica and alumina are the major constituents in fly ash along with lime. Aluminosilicates and unhydrated lime present in fly ash, in presence of water, undergo a pozzolanic reaction and form cementitious bond which holds the particles together. Bentonite is commonly used as binder in micropelletization of process waste to attain the mechanical strength required for handling and transportation. The bonding of particles by bentonite is a physical mechanism, while fly ash bonding is a chemical mechanism. The present paper deals with the partial replacement of bentonite with fly ash in micropelletization without affecting the quality of micropellets.

Jul 30, 2021

By D. S. Choi, H. D. Dahl, D. L. McCain

The paper examines current room and pillar mining practice in the U.S.A. from the standpoint of rock mechanics. Consideration is given to the deformation characteristics of the roof formation and the coal seam as determined in the laboratory as well as in the field. The results can be utilized by the practicing mining engineer to improve current mine design practice.

Jan 1, 1982

Traction of mining vehicles is well understood for a variety of unfrozen road surfaces, allowing optimal design of mine access and haulage roads. However, no such characterizations exist for the frozen or partially frozen surfaces typically encountered in Northern regions. Recent work by U. S. Army researchers suggests methods for characterizing roadway traction for any vehicle on the basis of test measurements made with a standard test vehicle. Such a test vehicle was designed, and several sets of test data were recorded at the onset of winter in Fairbanks, Alaska. This work suggests methods for future research and possibilities for the use of such research in designing drive systems, tires, and mine roads for Arctic and sub-Arctic mines.

Jan 1, 1995

Anomalous geologic or stress conditions ahead of the longwall face can cause great harm to both the individual miner and the mining operation as a whole. The U.S. Bureau of Mines has been developing seismic tomography techniques to image the panel ahead of the face. This paper presents the results of a field effort in which a 60-m (200-ft) segment of a longwall panel containing a fault zone was surveyed daily as the face approached. Stress distribution, geologic structure, and dynamic elastic properties within the panel were plotted and compared to static laboratory measurements. The surveys successfully imaged an anomalous stress concentration, likely influenced by the presence of the fault zone. The calculated dynamic physical properties generally agreed with laboratory measurements.

Jan 1, 1995

By Thomas L. Craig

The Wellman-Lord SO2 Recovery Process is operating commercially at one location in this country and at two locations in Japan. Tail gases from a sulfuric acid plant, from an oil fired steam generator and from a sulfur recovery unit are the respective applications. 1) At the Olin Corporation's Paulsboro, New Jersey, stack gas from a spent acid regenerative sulfuric acid plant-45000 SCFM - is treated in the W-L unit to reduce sulfur dioxide concentrations from 4500 ppm to less than 500 ppm. 2) At the Japan Synthetic Rubber plant in Chiba Prefecture, stack gas from an oil-fired steam generating plant - 120,000 SUM - is reduced from 2100 ppm S02 to less than 200 ppm. 3) At the Toa Nenryo Kogyo refinery in Kanagawa Prefecture, tail gas from a sulfur recovery (Claus) unit - 41,000 SUM - with, an inlet SO2 concentration of up to 13000 ppm is reduced to less than 200 ppm. The three installations are operating successfully and are capable of reducing S02 emissions to levels significantly below the concentration guaranteed. With the one exception of a higher than guaranteed chemical make up requirement at Paulsboro, utility and chemical requirements will be less than design.

Jan 1, 1971

By Harry Leslie Bullock

With silica making up more than 27% of the earth's crust, its oxides amounting to more than 59% of the igneous rocks and quartz the most prevalent of the main free oxides, it follows that the mining engineer' is in constant contact with quartz, mainly as a gangue material to be removed as completely and economically as possible and sometimes as a valuable mineral to be purified' for the chemical,, ceramic or glass industries. Water scarcity under desert or semi-arid conditions, dwindling water supplies and difficulties of wet waste disposal in many locations and trouble from freezing in arctic locations make dry benefication more and more desirable. Advances made during the last few years in apparatus and methods and a steadily increasing knowledge of solid state physics are widening the field open to the economical application of electrostatic separation.

Jan 1, 1967

By J. P. Bunch

As the number of environmental laws continues to steadily increase and the economic penalties for contamination problems become more severe, environmental management represents an important management function within today's U. S. mining industry. The economic impact to a mining company for contamination is not only realized in legal fees and fines but also in the cost of doing normal business. For example, a mining company with contaminated property applying for a loan may be refused because of a lending institution's reluctance to finance due to liability concerns. Or, an insurance company may decide to greatly increase its annual premiums because of existing or potential contamination problems. One of the main duties of the environmental manager is to seek ways to reduce these types of problems by eliminating contamination or by knowing what problems exist and designing corrective measures to prevent the situation from worsening.

Jan 1, 1990

By H. M. Castrantas

Caro's (peroxymonosulfuric) acid has been reported to destroy WAD (weakly acid dissociable) CN-but, until recently, the technology has not been demonstrated in other than a laboratory setting. During the last two years, Caro's acid has been shown to successfully detoxify WAD CN-in tailings at two large North American gold mines. Using on-site FMC generators, Caro's acid reduced the WAD CN-from 40-55 ppm to below 20-35 ppm WAD CN-, the target range for the two mines. The detoxification costs using Caro's acid were less than 50% of the treatment cost of using hydrogen peroxide, the previous oxidant of choice. In addition to the considerable savings in CN-detoxification costs, lower WAD CN-values were achieved and the detoxification time with Caro's acid was greatly reduced compared to hydrogen peroxide.

Jan 1, 1995

By Yiming Sun, David Tsztoo, Rick Nolting, Adam M. Wirthlin, Rebecca Fusee

"Excavation and initial support of the New Irvington Tunnel presented significant challenges, including rapidly changing ground conditions, heavy ground loads, and squeezing. Such behaviors were anticipated from historic tunneling records of the adjacent Existing Irvington Tunnel, and extensive site investigation, but clearer understanding of their actual extent and causes has resulted from convergence measurements, observations of ground behavior, initial support monitoring and detailed geologic mapping. Time-dependent movements, documented hours to months after excavation in clay-rich rock and in moderately to intensely fractured rock, identified squeezing areas, allowed classification by currently-used predictive methods and added to the list of lessons learned in tunneling such ground. INTRODUCTION In March 2003 the San Francisco Public Utilities Commission (SFPUC) authorized funding for the $4.6 billion Water System Improvement Program (WSIP) to repair, replace, and seismically upgrade its water system. The program consists of 35 local projects located within San Francisco and 48 regional projects located in several counties from the Sierra foothills to the San Francisco Bay Area. The New Irvington Tunnel (NIT), a key component of the WSIP, is located east of Fremont in Alameda County, on the east side of San Francisco Bay. The NIT is a new 18,660 foot (5,689 m), redundant tunnel, 190 to 670 feet (58–204 m) offset from, and subparallel to the Existing Irvington Tunnel (EIT). Built between 1928 and 1932, the EIT was constructed with an unreinforced cast-in-place concrete lining and is vulnerable to damage in the event of a major earthquake along the two closest active faults. The Hayward Fault is located less than a mile west of the tunnel, and the Calaveras Fault is located half a mile east of the tunnel. Although the alignment does not intersect these faults, the shaking and sympathetic displacement along secondary faults that cross the tunnel alignment are potential hazards. The NIT provides a seismically reliable water transmission facility capable of withstanding earthquake damage and maintaining continuous water service after a major earthquake. The NIT also adds system redundancy and provides for operation flexibility of running water through both tunnels, or through one tunnel while the other is out of service for inspections and maintenance."

Jan 1, 2016

By J. A. Bartnik

Flocculation, the process of coagulation or coalescence of finely divided particles, is commonly used in separating fine solids from fluids. Forces disposing of the particles to flocculate include: ionic forces of attraction, secondary entropic forces, and magnetism. Magnetic flocculation is due to a physical magnetizing process which affects suspended ferromagnetic particles. Such particles, after exposure to magnetic fields strong enough to cause reorientation of the particles and alignment of the induced magnetic poles, tend strongly to retain this induced magnetism, as the magnetic retentivity of ferromagnetic particles is a linear function of its specific surface.1 Thus, because they become small magnets with high residual magnetism, the particles become and remain attracted to one another, forming large agglomerates. Fine magnetic particles close to domain size can exhibit energies of the magnetization of the order of 105 ergs/cm3,2 which is many times greater than the energy affected by chemical flocculents. Therefore magnetic flocculation can be used to agglomerate particles having surfaces ionized with like charges and only a minute quantity of ferromagnetic material will be necessary to develop sufficient force to overcome the repulsive ionic forces and hold together relatively large masses of fine solid agglomerates suspended in fluids. Since flocculation occurs after the fine suspension passes through a magnetic field generated by magnets surrounding a pipe section, the simplicity of the process and economic advantage makes magnetic flocculation very attractive.

Jan 1, 1971

By C. L. Molina

The U.S. Geological Survey (USGS), in cooperation with the Bureau of Land Management (BLM), Geological Survey of Wyoming, and U.S. Bureau of Mines (USBM), will produce an estimate of the amount of available coal in an area about 55 Ian (35 miles) south of Gillette, Wyo., where the Wyodak coal bed is 8-27 m (25-90 ft) thick. Available coal is coal that actually is accessible for development under current regulatory, land-use, and technologic conditions. Local coal-development considerations include roads, ranches, railroads, pipelines, power lines, wildlife and archaeological sites, alluvial valley floors, cemeteries, and the Hilight oil and gas field and gas plant. Some of these considerations would be mitigated so that surface mining may proceed; others presently preclude mining in their vicinity.

Jan 1, 1995

By F. Vallianatos

The main objective of the present investigation is to demonstrate the potential of ERT (Electrical Resistivity Tomography) and HVSR (Horizontal to Vertical Spectral Ratio) methods as geophysical tools for the monitoring of subsurface cavities. The survey sites are located in Akrotirion Peninsula, almost 7 km east of Hania town in Crete Island, Greece. At this site, the surface expression of a known cavity with a diameter of about 25 m is visible. The true geometrical characteristics of the cavity were unknown since there are no boreholes in the area. The focus of this survey was primarily of a qualitative nature and the objective was to determine if ERT and HVSR could be used to identify and map near surface cavities (less than 30 meter in depth) in a limestones kartsic area such as Akrotirion Peninsula. A 2D/3D model of the resistivity distribution is given for the area under investigation. Furthermore, analysis of microtremors data provides a profile of the seismic response of the tectono-karstic voids.

Jan 1, 2006

By Verya Nasri

This paper will present the design and construction of a deep underground station of the Réseau Express Métropolitain (REM) project; the Édouard Montpetit station. The Édouard-Monpetit station is an interchange station that will connect the deeply sitting REM tracks to the existing metro station of the same name located closer to the surface. Édouard-Montpetit station is expected to be the deepest in North America, surpassing the famous Forest Glen Station. The various challenges and solutions put forth for the successful completion of this underground work are presented to serve as a valuable example for future deep excavation performed in urban area, in the close vicinity of highly sensitive structures.

Jun 13, 2021