Search Documents

By S. Garcia

The Minera Yanacocha operation presents various operating challenges, due to the complex structure of several heaps interconnected with ponds and gold recovery plants. A comprehensive process model has been developed in order to better understand the effects of certain operating parameters on issues such as water usage and inventory. An integral component of the water/mass balance of the process is a model of each heap that describes the flow and chemical behavior based on the individual characteristics of the heap. A computational fluid dynamic (CFD) software framework is used to model the individual heaps. The structure, calibration and validation of the model are described. Several examples demonstrating application of the process heap model are presented for the La Quinua heap. The effects of loss of solution flow to the heap (i.e., pump failure), increased cyanide levels in applied solutions and higher copper head grades on the process operation and balance are investigated with model simulations and compared to the baseline operating conditions. An example of estimating gold production and inventory based on projected heap loading plans is provided.

Jan 1, 2010

By L. Yuan, J. H. Rowland, R. A. Thomas, D. Bahrami

Blasting is the main method of production in many non-coal underground mining operations and produces multiple toxic gases as a result. The Mine Safety and Health Administration (MSHA) requires mine operators to measure the level of toxic gases in mines as frequently as necessary to ensure they are below regulatory safety limits. The current practice uses portable gas monitors to check the concentrations of toxic gases after a fixed post-blast time. This paper studies the application of a gas monitoring system in the return entry of a limestone mine to determine a safe re-entry time. The National Institute for Occupational Safety and Health (NIOSH) conducted such a monitoring program in a limestone mine from September 2016 through May 2018. NIOSH/PMRD (Pittsburgh Mining Research Division) is endeavoring to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions. This study showed that the use of gas monitoring in the return air can be a useful tool at the mine operator’s disposal to detect and reduce the risk of hazardous conditions and also to reliably estimate the re-entry time. INTRODUCTION Underground miners are at risk of overexposure to toxic gases from various sources. Production blasting operations using explosives in underground mines are a source of multiple toxic gases that could be harmful and even fatal to humans if prolonged exposure occurs beyond the safe limits. According to Code of Federal Regulations, Title 30, Part 57.5002 [1], metal and nonmetal mine operators must conduct gas, mist, and fume measurements as frequently as necessary to determine the adequacy of control measures to protect miners from overexposure to harmful gases. MSHA will inspect mine operators’ activities to verify the evidence of such measurements [2,3]. Continuous gas monitoring in the return air is an effective way to make sure that toxic gas concentrations at the working areas are kept below the regulatory limits before the return of miners. Toxic gases can enter the mine atmosphere from different operations, such as welding, combustion, and blasting. The main gases produced from blasting are carbon monoxide (CO), carbon dioxide (CO2), nitric oxide (NO), and nitrogen dioxide (NO2). Other gases are produced in small amounts and, therefore, were not considered for this study. Related regulatory and recommended exposure limits of CO, NO, and NO2 gases are summarized in Table 1 [4].

Jan 1, 2019

By William E. Horst

Ore grindability data based on various techniques to measure comminution characteristics are used to evaluate the crushing and grinding efficiency in mineral processing operations. The importance of achieving improved comminution efficiency, in terms of energy consumption, has been emphasized by recent increases in the cost of electricity. From a theoretical standpoint, the objective of a grinding operation might be expressed as maximizing the production rate at a given grind size while minimizing the energy consumption per ton of material ground. To achieve this objective in an industrial operation presents a challenge especially in view of changes in the raw material which are normally encountered. Various procedures1-5 used to determine energy-size parameters and grindability measurements have been reported. The proposed relationships between particle size and energy consumed have much in common between many of the techniques for measuring grindability. Probably the most widely used parameter to measure ore grindability in recent years is the Bond work index6, Wi, which is defined as the kw-hr per ton required to break from infinite size to a product size of 80 percent passing 100 microns. If the breakage characteristics of a material remain constant over all size ranges, then the calculated work index would be expected to remain-constant since it expresses the resistance of material to breakage. However for most naturally occurring raw materials differences exist in the breakage characteristics depending on particle size, which can result in variations in the work index depending on grind size. Consequently work index values are generally obtained for some specified grind size which typifies the comminution operation being designed or evaluated.

Jan 1, 1975

By J. Kennedy

Rare Earths: Understanding The United States complete failure of status and relevance in Rare Earth Oxides, Elements and Alloys. Although rare earth oxides are strategic and critical in their own right, elements and alloys are even more important for the development of "Green Technologies" and advanced weapons systems. America does not have an active domestic source of rare earth oxides. America does not have any Heavy Rare Earth Elemental or Alloy capabilities. The magnitude of this failure continues to become more apparent as the manufacture of REO based electronics and magnetic components moves eastward towards China. China has succeeded in outmaneuvering The United States and the world in its quest to control the Rare Earth Oxides, Elements and Alloys, and the many industries dependent upon REO. What can be done?

Jan 1, 2010

By J. F. Brune

"Re-occurring face ignitions in U.S. coal mines are concerning and require a closer look at air quality monitoring systems and practices employed in these mines. The explosion disaster at the Upper Big Branch mine in West Virginia in 2010 caused 29 fatal injuries and was largely caused by inadequate water sprays and inadequate ventilation monitoring. In this comparison, the author compares ventilation system monitoring in Australian, German and U.S. underground coal mines and makes recommendations for improvements and best practices. Mines in Germany and Australia are adhering to more stringent requirements for monitoring air quality and quantity and for monitoring water spray systems on cutters to prevent frictional ignitions. Air quality should to be monitored for sufficient oxygen, toxic gases, explosibility and for fire gases indicating a potential fire. Ventilation monitors must also confirm that sufficient quantities of air are available. Fully automated, continuously recording atmospheric monitoring and alarm systems are established practices in Germany and Australia and should be mandated for U.S. mines as well, in addition to the current, regular spot inspections of the ventilation system by certified mine examiners. BACKGROUND: METHANE EXPLOSIONS, FACE IGNITIONS AND NEED FOR AIR QUALITY MONITORING Accumulations of methane in face areas of underground coal mines frequently lead to ignitions that can cause burns, traumatic injuries and, in the case of the 2010 Upper Big Branch disaster, cause major explosions with multiple fatalities. Table 1 shows the number of reported face ignitions in U.S. coal mines between 2010 and 2014, based on statistical data published by MSHA (MSHA 2010 – 2014). Although there appears to be a downward trend in such ignition incidents over time, ignitions continue to occur with some regularity; and each ignition may cause a potentially catastrophic mine explosion.Per regulation, all U.S. coal mining machinery, continuous miners and longwall equipment, is outfitted with continuously monitoring methane sensors wired to cut power to the equipment as the methane level exceeds 1%. Face ignitions keep occurring because these sensors are usually not positioned in sufficiently close proximity to the coal cutting drums or to the freshly exposed coal face where the methane is most likely released. Therefore, methane may accumulate in explosive concentrations near the coal face and the cutting drums long before the gas concentration reaches the 1% level near the monitor and creates an alarm."

Jan 1, 2016

By E. J. Onuscheck

Coal mine safety of the past was plagued by disasters that took the lives of thousands of miners. Through the years new mining methods, improved laws, and a commitment from the mining industry has reduced the frequency of such incidents to a minimum. History tells us that coal was mined in the early 1700's in Virginia primarily for use by blacksmiths -- most of that mining was done in the Richmond area. It was in those mines that methane was encountered; as workings became more extensive, methane explosions became more frequent. In the early 1800's the first recorded explosion occurred near Richmond, Virginia -- 40 men were killed.

Jan 1, 1985

By K. N. Han, M. C. Fuerstenau, T. B. Onlin

An investigation of the removal of finely divided silica, coal, and alumina particles less than 20,µm in size has been carried out using liquid fluidized and packed beds. The bed particles used included 48x100, 100x150, and 150>200-mesh silica, corundum, and ilmenite particles. Important variables examined included surface charge, flow rate, pH and amount of bed particles. Surface charge has been identified as the most important variable in this system. Van der Waals force also assumes a very important role in the recovery of fine particles in fluidized and packed beds. In addition to interaction between large and fine particles, interaction between fine particles themselves assumes an important role in the overall recovery.

Jan 1, 1987

By C. M. Brinckerhoff

Much has been written in the mining technical magazines about the caving system. Many of these articles were published in the Transactions of the American Institute of Mining Engineers prior to World War II. In recent years little has been written on mining methods or on the detailed planning always required. Block caving had primarily been used to mine deep copper ores in Africa, the United States and in Chile, although other ores had been mined by this same system. Asbestos ore had been caved in Canada, tin ore in Bolivia, molybdenum ore in Colorado, iron ore in Wyoming and Sweden, and limestone in California.

Jan 1, 1984

By W. R. Reed

NIOSH continues to conduct respirable dust control research for surface mine blasthole drilling operations. Research areas have included testing variables (shroud leakage area, drill deck cross-sectional area, shroud height, collector-to-bailing airflow ratio, etc.) that have the most impact on respirable dust control, development of a dust collector inlet hood, development of a dust collector dump point shroud, and testing of a small diameter water separating sub. This paper summarizes the results of the aforementioned research that has been completed. Additionally, past dust control research for drilling operations of both underground and surface mines completed by the U.S. Bureau of Mines, created in 1910 and incorporated into NIOSH in 1997, is reviewed.

Jan 1, 2008

By G. S. Dobby

Particle collection is considered to occur by particle collision with the bubble followed by the particle sliding over the bubble during which attachment may occur. Collision is quantified by a collision efficiency, EC. The existing model for EC is extended by including particle inertia. Attachment is quantified by an attachment efficiency, EA calculated as the fraction of particles which reside on the bubble for a time greater than the induction time. These calculations use recent data on the liquid velocity distribution over the upper half of rigid spheres. Collection efficiency, EK is given by EK = EC ? EA. Detachment is not considered. The mode is examined and shown to agree with much experimental data. For example the maximum observed in recovery vs particle size (d) can be explained as E increases with increasing d , while EA decreases. The decrease in selectivity at fine sizes is in accord with the model result that for dp < 5µm, EA ? 100% (i.e. EK ? EC) almost regardless of induction time. A decrease in bubble size does increase EK but does not improve selectivity. A high particle density (> 5g/cm3) is shown to cause a sharp peak in recovery vs size and a decreased maximum size of floatability. Finally, the possible effects of bubble and particle concentration are explored.

Jan 1, 1985

By Donald M. Podobnik

The Cuajone Concentrator of the Southern Peru Copper Corporation is located approximately 900 kilometers southeast of Lima, Peru, near the 500 year old town of Moquegua, in an area that has been occupied since antiquity. Since the plant was started in July, 1976, the throughput has steadily increased from 36,000 to 46,000 metric tons per day. The widely distributed molybdenite content of the ore body ranges from 0.02 to 0.04% MoS2. The molybdenite content of the copper concentrate has always been sufficient to justify operation of a byproduct molybdenite plant. During the first nine months of 1980, the average grade of the ore was 1.169% copper and 0.026% molybdenite.

Jan 1, 1981

By M. Dayne Aldridge

A description is given of an experimental ventilation control system designed, built, and tested by WVU under United States Bureau of Mines sponsorship. A description is given of the control, system used and the mine-wide microcomputer-based ventilation monitoring system used with it. Test results of experiments conducted with this system at Eastern Associated Coal Corporation&apos;s Federal No. 2 underground coal mine are presented. In addition, a brief description is given of a new microprocessor based system presently being tested.

Jan 1, 1980

By R. E. Ray

As coal reserves at shallow depths continue to be exhausted, a number of U.S. coal mining companies are beginning to develop coal seams previously thought to be coo deep to mine economically. Because of increased cover load, mines operating in deeper seams face unique ground control problems. In addition, the volume of methane gas contained in coal beds increases with depth, and ventilation requirements are much more stringent for deep underground coal mines than for shallower mines. When the longwall mining method is used at great depths, ventilation, ground control, and operational considerations must all be addressed in the design of longwall panels. This paper examines the influence of these factors, particularly ventilation and operational considerations, upon the feasibility of two, three, and four-entry longwall development panels in Jim Walter Resources&apos; four deep mines.

Jan 1, 1986

By R. Perez

The consumption of grinding media forms a significant part of the operating cost of a mineral processing plant. An estimated half billion pounds of steel in the USA and over one billion pounds in the world are consumed each year in wet grinding alone. However, there is some conjecture as to the interacting roles of abrasion and corrosion. In order to provide a more complete picture of the conjoint action of abrasion and corrosion, marked ball tests were conducted on different grinding ball compositions in a laboratory ball mill and the metal losses were measured on varying the conditions, i.e., pH, PO2, in wet grinding a Cu-Ni gabbroic rock and compared with taconite grinding. Ball wear rates ere discussed with respect to ball composition and microstructure and the varying conditions used in the grinding tests.

Jan 1, 1984

By P. Somasundaran

Electrochemical properties of silicate minerals govern their behavior in processes such as flocculation and enhanced oil recovery that can occur at elevated temperatures. Knowledge of these properties as a function of temperature can be helpful in developing an under- standing of the role of these interfacial properties at non-ambient temperatures. Zeta potential of Sodium Kaolinite and quartz has been determined as a function of pH and temperature in this work. Both systems exhibited markedly different behavior at higher temperatures and also exhibited significant hysteresis. Results are examined in terms of possible dissolution of the minerals and surface reactions at different temperatures.

Jan 1, 1986

By David M. Koogler

If you are contemplating starting a small coal mining operation there is a good possi¬bility that you can not afford it. If you, have already started, you may be on the road to bankruptcy. If you are a small but well established operator you may be trading dollars, or even dissipating your capital, equipment and other assets. A bleak outlook? Yes! Meant to be discouraging? No! Just a reminder that, with todays costs of doing business, high interest rates, rapidly increasing costs and decreasing sales prices, a small businessman/miner had best watch closely or he will be mired in something worse than a soft bottom - namely a cash and credit shortage, and in too many instances In recent times, bankruptcy. We will not dwell on what happens once you are that far gone, though I could cite a good example. But, let us look at what should be done to avoid such a catastrophe.

Jan 1, 1981

By M. A. Georgiana

The Emerald Mine No. 1, located in southwestern Pennsylvania is presently owned and operated by Cyprus Minerals of Englewood, Colorado. High volatile bituminous coal is produced from the Pittsburgh No. 8 seam by both longwall and continuous mining methods. The coal is then mechanically cleaned on site utilizing a combination of heavy media separation and froth flotation methods prior to shipment to both the metallurgical and steam coal markets. The Emerald Mine is presently producing 2.8 million raw tons per year, while liberating approximately 6.5 million ft per day of methane. In light of the methane liberation rate, ventilation requirements have been significant and have always received utmost priority and consideration. Figure 1 shows the locations of the current and proposed shafts. Emerald utilizes two Joy (Model M120-58-880) axial vane fans on shafts No. 1, No. 2R, No. 3R. (one operational, one stand-by) The use of computer simulation of various ventilation networks was initially employed during the design stages (1975-1977) and has been utilized through the present. Obviously, the initial planning, under the ownership of Lykes Resources, was strictly theoretical. All the quantities were proposed and the resistances were based on prior simulations of other mines and mathematical formulas. However, once the mine was moderately developed, actual values were recorded and utilized. This procedure consists of: a) layout pressure and quantity points b) measure all air quantities where an air course splits

Jan 1, 1986

By Paul J. A. Lever, Robert H. King

Human operators, geological conditions, equipment changes, mining sequences, and roof conditions are some of the continually changing operating conditions that drive a dynamic mining environment. These dynamic characteristics make it difficult to automatically analyze mining data because attributes change as the mining environment changes. Mine monitoring systems could provide mine managers with much more useful information than they do presently, if automatic analysis were possible. Automatic analysis of sensor data is also key to autonomous mining systems. This paper describes artificial intelligence (AI) and sensor fusion based sensor data analysis techniques developed over the past four years. These techniques were used to classify machine operating events by continuously monitoring machine power usage in a continuous miner section at an under- ground coal mine. The result is a report similar to an industrial engineering time study. First, numerical pattern classification techniques broadly identify operating events. However, domain knowledge about inter-machine and intra-machine interactions is necessary to identify and refine dynamic event boundaries. By implementing AI and sensor fusion based techniques we are able to classify machine events more accurately and recognize more specific events. These techniques could easily be applied to many different mining sensor data applications

Jan 1, 1993

By Z. D. Hora, W. N. Hamilton

Evaporite units of the Western Canadian Sedimentary Basin are known to host native sulfur. In British Columbia, a large number of oil and gas exploration drilling holes reported intersections with native sulfur. The most important ones include 6 meters (20 feet) and 27 meters (90 feet) of native sulfur among 23 occurrences in Devonian Muskeg evaporite or adjacent Slave Point reef facies carbonates. A small Frasch sulfur deposit is known from Devonian Wabamun Group sediments near Camrose in South Central Alberta. Occurrences of native sulfur are common also in association with presently mined gypsum of Devonian Burnais Formation in southeastern British Columbia. Triassic sediments with evaporite members in British Columbia are also known to contain native sulfur showings. A widespread presence of anhydrite in many sedimentary units of Alberta and British Columbia together with oil and gas fields in the same areas and associated native sulfur occurrences point to a possibility for Frasch sulfur deposits in this part of western Canada.

Jan 1, 1992

Sinter mixes of three iron ore types were prepared with a range of water contents in a laboratory investigation. The mean diameter of the granulated mixes and the void fraction of beds of the mixes were determined experimentally. Pressure drop measurements over a range of flow rates were made in a laboratory permeameter with pressure tappings at several depths in the bed. The Ergun equation was applied to the results to determine the shape factor of the granulated mixes. The pressure readings down the bed were used to estimate the local void fraction in the bed using the Ergun equation and the calculated granule shape factors and it was found that there was a decrease in void fraction with depth in the bed. The significance of this and the variation of the shape factor values with the amount of water used for granulation is discussed in relation to the strength of granules of the sinter mixes.

Jan 1, 1984