Search Documents

By R. A. Gee, G. B. Ashton, S. T. Warren, P. N. Groves

Northside Storage Tunnel provides 500 megalitres (Ml) (130 million gallons) of storage capacity to capture stormwater/sewage overflows into Sydney Harbour. The6.6 m diameter TBM driven tunnel traverses Middle Harbour 85 m (280 ft) below sea level and through a sandstone/shale rock mass, highly disturbed by stress relief, 20 m(65 ft) beneath the base of the sediment filled palaeochannel. Target limits for inflow, groundwater drawdown and settlement of the valley beaches were achieved by systematic forward grouting from the TBM. Support included rockbolts, sets and shotcrete to carry rock loads, control block instability and spalling and to provide durability and serviceability. This paper describes the tunnelling and grouting works and their effectiveness.

Jan 1, 2001

By C. Mark, D. M. Pappas

From 1999 through 2008, groundfall events resulted in 75 fatalities, 5,941 injuries and 13,774 noninjury roof falls in U.S. underground coal mines, according to the U.S. Mine Safety and Health Administration (MSHA). A comprehensive analysis of these events was conducted to better understand where and why these incidents occurred. The first segment of the study used the MSHA database to evaluate groundfall injury rate trends related to mining method, year, locality, seam thickness, mine size, coalbeds and seasonal effects. In the past decade, roof fall injury rates have dropped 50%, but rib fall injury rates have remained constant. Room-and-pillar mines had a roof fall injury rate that was nearly 2.5 times the longwall rate. High groundfall rates occurred in the Illinois Basin, a finding that correlates with other studies that have shown that roof rock in the Illinois Basin is weaker than that in the central Appalachian coalfields. Finally, noninjury roof fall rates in the eastern and central United States were found to be 50% higher from July through September, possibly because of the changes in humidity levels that may cause shale mine roofs to deteriorate. The second segment of the study evaluated the root causes of failure by reviewing all MSHA groundfall fatality reports for 1999-2008. Pillar recovery was the leading cause of groundfall fatalities (19%), followed by rib falls, roof skin falls and traveling under unsupported roof (16% each). Defining prominent ground control incident trends and hazards will identify areas where additional study is needed and where innovative solutions need to be developed to reduce these severe occupational hazards.

Jan 1, 2011

By Leon Maday, Robert Robinson, Judy Cochran, Don Davis

Over the past 20 years, several soft-ground tunnels have been successfully completed in the Seattle area. These tunnels were built using design-bid-build contracting methods, and have benefited from advancing technologies in exploration, design and construction methods. Owners have utilized various contractual means to share some of the risks that are inherent to tunneling projects. This has helped to foster a competitive bidding environment and to resolve issues related to unanticipated underground conditions in a fair manner. This paper presents case histories of tunnels constructed by King County and the Washington Dept. of Transportation that illustrate a common approach to design and construction issues. The common thread is successful project completion with minor cost changes under the design-bid-build contracting method. Lessons learned from these projects are being applied to the upcoming King County Brightwater Project tunnels, Sound Transit’s Light “Link” Rail tunnels and other tunnel projects.

Jan 1, 2005

By G. Danko

MULTIFLUX, a new thermal, hydrologic, and airflow model and software is being developed to solve the flow of heat, moisture, and air in and around an underground opening. MULTIFLUX couples two distinct domains that are solved separately first and re-coupled as an iterative task: (1) the rockmass, and (2) the airway. The airway is solved with a lumped-parameter Computational Fluid Dynamic (CFD) module which is an embedded part of the MULTIFLUX code. The CFD model includes convection, conduction, and radiation for heat, as well as convection and diffusion for moisture transport in an air-filled opening. The CFD model also solves for the airflow field. The surrounding rockmass model may be from any analytical solution, or from a complex thermal-hydrologic numerical model such as NUFT or TOUGH2. The rockmass model is interfaced to MULTIFLUX using a novel technique called Numerical Transport Code Functionalization (NTCF). The method provides fast convergence on a personal computer platform. The paper reports the results of MULTIFLUX simulations for a mine drift, comparing calculations with a known mine climate software, CLIMSIM, and with measured data. Through this validation example, the performance of MULTIFLUX is demonstrated. The results show excellent agreement due to the use of realistic modeling assumptions and boundary conditions.

Jan 1, 2009

By Brett Campbell

The San Vicente to 2nd Aqueduct Pipeline?Tunnel project is a raw water conveyance tunnel linking the San Vicente Reservoir (SVR) to the 2nd Aqueduct Pipeline via Rancho Penasquitos Pressure Control Facility (RPPCF). This 58,230 lf long tunnel will be 8.5? final ID, and has four points of construction access. The job is classified into 6 Reaches of tunnel, identified by the dominant geology within the reach. This paper will focus on Reach 3, specifically the measures necessary to drill and blast a 550 lineal foot section of granitic rock tunnel immediately in front of an open face digger shield.

Jan 1, 2008

By Steve Kral

MINExpo INTERNATIONL 2000 was a good place for companies to introduce new products, technologies and services to the mining industry. Caterpillar took that a step further. The company hosted a one-day preview of its mining products at its Tinaja Hills Training and Demonstration Center near Tucson, AZ. About 30 members of the trade press spent the day at Tinaja Hills before heading on to Las Vegas for MINExpo INTERNATIONAL 2000. Dozens of Caterpillar professionals provided the editors with a first-hand look at Caterpillar’s mining trucks, loaders, excavators, road graders, water trucks and engines. In addition, these Cat experts explained the intricacies of each piece of equipment, the latest technology that led their improvement and their value to the company’s mining customers.

Jan 1, 2000

By Galyn Rippentropp, Finn Erik Overlie

INTRODUCTION The wet shotcreting system utilizing steelfiber microsilica shotcrete with remote controlled equipment (The Robocon System) was developed in Norway 7-8 years ago. Norway was the natural origin for this system due to several factors. Almost 30% of all underground hydro-power stations in the world are located here. These projects created a need for high productivity shotcreting rigs for the rock support work in the caverns and in the connecting tunnels. During the period of 1976-1980, more than 1000 miles of tunnels were completed in Norway. Secondly, the utilization of microsilica in concrete was also developed in Norway due to a concentration of the world's ferroalloy p ants there. Robocon has presently placed approximately 110,000 m (150,000 cu. yds.) of this superior shotcrete, and has consequently an extensive experience in the shotcreting method. During a relatively short period of time (1975-1980), Robocon had a change from hand-operated, dry-process shotcrete to remote-controlled, wet-process shotcreting, because of improved productivity, reduced rebound, safer and cleaner working conditions. The introduction of microsilica and water-reducing admixture made it possible to produce wet-process shotcrete of high strength.

Jan 1, 1987

By William R. Yernberg

The Cripple Creek & Victor Gold Mining Co.(CC&V) celebrated completion of a two-year, $168.5-million expansion and capital improvement program. An open house celebration was held in the historic mining town of Victor, CO on Oct. 4, 2002. Hundreds of townspeople, the press and other invited guests from the mining industry joined the employees of CC&V in the celebration. The event included mine tours, company displays and a barbecue picnic, complete with a country and western band. The Cresson Mine is located about 40 km (25miles) west of Colorado Springs, CO between the towns of Cripple Creek and Victor. The mine is the only large-scale gold mining operation in Colorado and now employs about 300 (ME, October 2001, pp.21-28). The operation is a joint venture between Anglo-Gold (Colorado) (67%), based in Greenwood Village, CO, and Golden Cycle Gold (33%), based in Colorado Springs. CC&V is managed by AngloGold North America. AngloGold North America is the U.S. subsidiary of AngloGold, the world’s second largest gold mining producer. AngloGold is based in Johannesburg, South Africa.

Jan 1, 2002

In Alaska?s southwest corner, in the Bristol Bay region, 476 holes have been drilled to help define the size of the Pebble Project. The results indicate that the deposit holds close to 32 Mt (72 billion lbs) of copper and 2.9 Gt (94 million oz) of gold. The Pebble Partnership, an Alaskan limited partnership of Anglo American and Northern Dynasty Minerals, owns the project that consists of two world-class mineral deposits. Currently in the prefeasibility and prepermitting stage of development, the Pebble Project is one of the largest and highest profile exploration projects in North America. History The Pebble West Project was originally discovered in 1988 by Cominco (now Teck Cominco). Drilling programs in 1997 defined a near-surface mineral deposit of 1 Gt (1.01 billion st). Minerals found included copper, gold and molybdenum. Northern Dynasty Minerals acquired the property in 2001 and, by 2005, it had confirmed a measured and indicated resource of 4.1 Gt (4.5 billion st) containing 1.2 kt (42.1 million oz) of gold, 11.2 Mt (24.7 billion lbs) of copper and 612 kt (1.35 billion lbs) of molybdenum and additional silver. By September 2005, Pebble East, a deeper, but richer deposit had been found. Drill data by the end of 2005 confirmed a 3.4-Gt (3.7-billion st) inferred resource containing 19 Mt (42.6 billion lbs) of copper, 1.2 Mt (39.6 million oz) of gold and 1.2 Mt (2.7 billion lbs) of molybdenum.

Jan 1, 2009

By J. C. Potvin

Although the occurrence of deposits of titanium minerals on Kenya’s present day beaches and adjacent dune systems has been well documented, the potential for older formations to host economically viable deposits had not been recognised until recently. The Magarini sands formation in Kenya has been found to contain deposits of ilmenite, rutile and zircon in quantities and grades that have the potential to be commercially exploited. Since 1995, Tiomin Resources Inc. has explored these deposits and has identified one deposit, the Kwale project, as being able to support the development of a mine producing some 300,000 tpa ilmenite, 75,000 tpa rutile and 37,000 tpa zircon. Tiomin plans to start production by late 2002. Construction of a US$137 million operation is set to commence in the first half of 2001.

Jan 1, 2001

By M. SIDDARAJU, Rameshwar Sah, T. Umadevi, K. S. SRIDHARA, B. D. Ganesh Shetty, M. RAJU

The production of high strength iron ore sinter for blast furnace iron making unit was developed by optimizing the granulometry of less than − 0.150 mm fines in sinter base mix which consists of iron ore fines (− 10 mm size with 0.150 mm: 41%), beneficiation plant jig concentrate, i.e., washed ore (− 3 + 0.150 mm size with − 0.150 mm 3 to 9%), beneficiation plant concentrate (− 0.150 mm size 97%), limestone, dolomite, coke breeze, lime, sinter return fines, direct reduced iron (DRI plant) fines, and micropellets produced from steel plant waste. The sintering process consists of preparation of base mix, mixing, and production of nodules using mixing and nodulizing drum by maintaining the optimum moisture, transferring of nodules to the sintering machine, and firing of sinter by applying optimum suction pressure. To optimize the < 0.150 mm fines in sinter base mix, the − 10-mm size iron ore fines was replaced with washed ore. The size analysis, granulation index (G index), and optimization of moisture w.r.t. sinter bed permeability were carried out by varying the washed ore addition from 0 to 55% in sinter base mix to vary the − 0.150 mm fine size. With decrease in washed ore addition from 55 to 0% in sinter base mix the finer fraction, i.e., − 0.150 mm in sinter base mix increased from 9.4 to 26.7%. Granulation (G) index increased from 1.46 to 3.10, sinter bed permeability increased from 33 to 53 Japanese Permeability Unit (JPU), and balling index increased from 1.4 to 3.0. With increase in − 0.150 mm fines in the sinter base mix from 9.4 to 26.7%, the sinter tumbler index (T.I) increased and sinter reduction degradation index (RDI) decreased. Increase in sinter strength and decrease in sinter RDI was due to increase in formation of Silico ferrite of calcium and aluminium (SFCA) phase and decrease in pore phase. The SFCA is the main bonding phase in iron ore sinter, and it provides strength to sinter. Sinter base mix with − 0.150 mm fines 18.9% (washed ore addition 25%) achieved desired sinter properties with moisture 8.0%, G index 2.44, balling index 2.3, and sinter bed permeability > 45JPU. Decreased the sinter properties with washed ore addition in sinter base mix beyond 25% due to decrease in − 0.150 mm fines in sinter base mix. Further, to improve the sinter properties with washed ore 30 to 45%, 3 to 10% beneficiation plant concentrate, i.e., − 0.150 mm fines was added to maintain the 18.9% of − 0.150 mm fines in sinter base mix. From the laboratory sintering studies, it was found that minimum 18.9% (range from 18.9 to 26.7%) − 0.150 mm fines should be maintained in the sinter base mix to achieve desired sinter properties.

Oct 16, 2021

By R. Pothina

The objective of this research was to develop a mathematical model for gyratory crushers to help in the prediction of energy consumption and to analyze dominant parameters that affect this energy consumption. The development of a gyratory crusher model was achieved in the following three main stages: mathematical representation and coding of the crushing process; building an amperage constant model to derive an energy-scaling formula; and modifying the amperage constant model to represent a full-scale model. Due to their significant influence on feed-size distributions, two blasting parameters, i.e., burden and spacing, were considered. The crusher parameters that affect energy consumption were also identified. A case study of an operating dolomite mine was performed. The results indicated that by changing the burden, spacing and crusher closed-side setting, the overall (blasting and crushing) costs could be reduced by 4.7% to 7.9% annually. It can also be concluded that burden and spacing values have a linear positive relationship with the crusher energy consumption, while closed-side setting values have an inverse linear relationship with the energy consumption.

Jan 1, 2007

By M. Rice, M. Stanley, J. Marlow

Arizona construction aggregate industry remains in the crosshairs of public debate, caught between the need for aggregate-based building materials and alternative, high-value land-uses. To better manage lands and improve land-use decisions, the Arizona State Land Department has need for a system to assess potential aggregate resources on State Trust lands, and assign dollar values accordingly. Thereafter aggregate values can be compared to residential, commercial, agricultural, recreational, and habitat values -- in a determination of highest and best land-use.

Jan 1, 2002

By Philip-Mark Spanidis, Christos Roumpos, Francis Pavloudakis

This paper presents a quantitative research (QNR) methodology, collaboratively conducted with a group of mining experts, to assess the knowledge management (KM) landscape in the Greek mining industry. The methodology involves a framework for structured data collection using questionnaires, statistical analysis, discussion on critical methodological aspects, and interpretation of results focusing on key aspects of interest for designers of KM systems. The paper concludes by summarizing the methodology’s outcome and proposing perspectives for further research.

Aug 1, 2024

By Seal. Thom

Large heap leach operations around the world contain significant under-leached metal values that present recovery challenges to operators. The first challenge is to find the location of the highest inventory. High resolution resistivity ? has proven sensitive enough to detect such zones in the interior of heap leach pads to target treatment or re-leaching. Newmont Mining Corp. has adapted the high pressure fracturing technology, used in oil wells to stimulate select zones in heap leach pads to add reagents in 3-D for re-leaching, changing zonal chemistry for improved recovery and heap closure. High Resolution Resistivity ? is able to subsequently monitor injected solution flow and determine directional permeability during Hydro-Jex stimulation. The combination of these technologies has shown strong economic success, for selecting targets in the heaps and monitoring solution application. These technologies are now available to the mining industry for adoption.

Jan 1, 2008

By B. C. Paul, R. Q. Honaker, K. Ho

Recent research has shown that froth flotation is not effective at treating fine coals (-28 mesh) containing a large portion of middling particles. Due to their relatively large density differences, middling particles can be separated more efficiently using gravity-based processes. The ability of gravity separators to treat fine particles has been limited by the lack of particle inertia relative to the surface drag forces. However, particle inertia can be enhanced by the application of a centrifugal field. A commercial-scale centrifugal Falcon concentrator capable of treating a mass flow rate of greater than 1 tph continuously has been used to evaluate its feasibility for treating fine coal as an alternative to froth flotation. Tests conducted on a -28 mesh fine coal circuit feed have found the Falcon concentrator to be very effective at cleaning the 28 x 325 mesh size fraction. For an Illinois No. 5 coal sample, the ash content was reduced in the 100 x 325 mesh size fraction from about 18% to 8% while achieving a high combustible recovery value of nearly 97%. In addition, the total sulfur content was substantially decreased from 2.6% to 1.7%. The effects of the critical operating parameters on separation performance have been studied and their values optimized.

Jan 1, 1995

By Thomas Novak, Sampurna Arya

Controlling dust generation and keeping it below permissible limits to meet federal dust standards at the working face of a roomand-pillar coal mine is a challenge for a mine operator. With the recent changes in federal dust regulations requiring lower worker exposure, maintaining compliance has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the National Institute for Occupational Safety and Health (NIOSH) indicated that a flooded-bed scrubber could achieve cleaning efficiencies between 58 and 90%. But, the operation of such a system is maintenance intensive. The flooded-bed scrubber screen becomes clogged with dust particles and requires frequent cleaning to maintain performance. However, the dust control issue is not solely a mining industry problem. Other industries face similar issues. The University of Kentucky collaborated with Toyota Motor Manufacturing on the development of a novel wet scrubber, called the vortecone scrubber, for capturing oversprayed paint particles in automotive paint booths. The vortecone scrubber achieved a cleaning efficiency of 99% and required minimal maintenance. This study aims to assess the ability of this vortecone scrubber to capture respirable dust in an underground coal mine. The paper presents the results of computational fluid dynamics (CFD) modeling of this vortecone scrubber. It discusses the effects of air quantity and dust particle size on the performance of the scrubber.

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES, DAVOOD BAHRAMI

Mine equipment fires remain as one of the most concerning safety issues in the mining industry, and most equipment fires were caused by hot surface ignitions. Detailed experimental investigations were conducted at the National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Mining Research Division on hot surface ignition of liquid fuels under ventilation in a mining environment. Three types of metal surface materials (stainless steel, cast iron and carbon steel), three types of liquids (diesel fuel, hydraulic fluid and engine oil) and four air ventilation speeds (0, 0.5, 1.5 and 3 m/s) were used to study the hot surface ignition probability under these conditions. Visual observation and thermocouples attached on the metal surface were used to indicate the hot surface ignition from the measured temperatures. Results show that the type of metal has a noticeable effect on the hot surface ignition, while ventilation speed has a mixed influence on ignition. Different types of liquid fuels also show different ranges of ignition temperatures. Results from this work can be used to help understand equipment mine fires and develop mitigation strategies.

Oct 1, 2022

By Levent Ozdemir, Robert J. Evans, Russell J. Miller, William Sharp

This paper describes the specifications and capabilities of a 6 ft (1.83 m) diameter laboratory rotary cutting machine which was designed and fabricated under a Bureau of Mines (USBM) contract awarded to the Colorado School of Mines (CSM). The machine will be used for carrying out research and development programs aimed toward improving the design and operation of mechanical tunnel, raise and shaft boring equipment.

Jan 1, 1983

By A. D. Davis, C. J. Webb, C. S. Johnson

The Belle Eldridge Mine is an inactive lead-zinc mine in Spruce Gulch south of Deadwood, South Dakota. Acidic mine drainage (AMD) produced at the site drains into Spruce Creek, a tributary of Whitewood Creek. The site is on U.S. Bureau of Land Management (BLM) property. Extensive fieldwork was done at the Belle Eldridge Mine through the cooperation of the BLM and the South Dakota School of Mines and Technology. The site was extensively mapped to identify physical and environmental hazards such as tailings, waste rock, collapsed buildings, adits and workings. An exhaustive search of the historical records of the Belle Eldridge Mine was conducted. Maps of the under-ground workings of the Belle Eldridge dating from the 1930’s and 1940’s were found. The maps were used to correlate currently collapsed features to old adits and tunnels. Using hand corers and a portable drill rig, waste rock, tailings and soil core samples were collected and depth to bedrock was determined and the total volume of waste and tailings pile were determined. Related work examined the hydrology of the site. The site is very complex hydrogeologically. Numerous underground and surface workings and tunnels add to the complexity. Several seeps are located at the site, one of which is producing AMD. Recharge to the site was studied, and a 100-year flood plain map was produced.

Jan 1, 2000