Search Documents

By G. D. Hood

The U.S. Bureau of Mines investigated rapid froth flotation through more efficient bubble-particle collisions that improved the overall flotation kinetics. An in-line static mixer efficiently mixed the bubbles, water, and ore, selectively attaching these bubbles to the hydrophobic mineral's surface. As the mixture entered the flotation chamber, the hydrophobic mineral was already attached to the bubbles and was quickly floated away from the remaining ore pulp. The rapid flotation system was evaluated for beneficiation with a western porphyry copper ore containing 0.67 pct copper, and a phosphate-bearing amine flotation tailings sample containing 9.5 pct P2O5 in a quartz matrix. Over 88 pct of the copper was recovered from the ore in a rougher concentrate containing 5.9 pct copper at a rate 7 times faster than conventional flotation. Sixty percent of the quartz in the phosphate-bearing sample was floated at a rate 4 times faster than conventional flotation. The unfloated product retained 80 pct of the phosphate in a l6.9-pct P2O5 concentrate.

Jan 1, 1993

By J. Hanna, H. R. Gonzalez

Discussion by N.L. Hargett Dear Dr. Hanna: As discussed in our phone conversation, we are enclosing a suggested revision to the paper, "Application of Bentonitic Clays in Suspension Fertilizer Formulations," published in MINERAL & METALLURGICAL PROCESSING, May 1990. The revision will replace the second paragraph in the article. The reason for the revision is that suspensions have decreased in market share since 1984 and at present comprise an estimated 25% to 30% of fluid mixtures. This represents 6% to 7% of all fluids and only 2% to 3% percent of all fertilizers. Based on national surveys conducted by the Association of American Plant Food Control Officials (AAPFCO), suspensions comprised an estimated 25% of all fluid mixtures in 1974, 33% in 1976, 35% in 1980, 40% in 1984, and 36% in 1988. Revision to "Application of Bentonitic Clays in Suspension Fertilizer Formulations." Suspension fertilizers are an important segment of the fertilizer industry in the United States. Suspensions allow higher concentrations of nutrients (N, P2O5, K2O) than clear liquid solution fertilizers. K20 content of solutions is limited to about 10%, while suspensions can contain more than 30% K2O. Suspensions can tolerate greater variations in temperature than solutions. In suspensions, if crystallization occurs, the crystals can remain suspended in a clay jell instead of settling as they would in solutions. Solubility is not a limiting factor in suspensions, since complete solubility of phosphate is not required. This allows a wider range of phosphate materials to be used. Also, materials commonly used in formulating suspensions are less expensive and more widely available than those for clear liquids (Getsiner et al., 1984).

Jan 1, 1992

By Raymond E. Zimmerman

The use of standard dense-media cyclones is well known, as they have been in use for many years. They are especially well suited for operating at low separating densities and for treating difficult coals containing a high percentage of near-gravity at the point of separation. Very few modifications of the basic design have ever been made. The author recently, however, has been interested in the development of a new type of dense-media cyclone that has been produced in Japan. He has observed the testing of this unit and has collected much data which he feels should be of considerable interest to coal preparation engineers. He feels that this unit, called the Swirl Cyclone, may be of substantial value as an alternate to the standard cyclones. It is certainly worthy of further investigation. There has been relatively little written in English-language publications on the Swirl Cyclone. It was briefly described at the Fifth International Coal Preparation Congress. I It has been described in a general manner by the author in two prior publications. 2, 3 This paper proposes to describe this device in more detail and at the same time submit technical data illustrating its wide characteristics.

Jan 1, 1977

By D. Watson

The Henderson mine has more than 20 years experience and has placed a combined total of more than 400,000 m3 (520,000 cy) of shotcrete and concrete. Over the last 20 years the mine has used a variety of equipment for placing concrete, wet shotcrete and dry shotcrete and is constantly trying to cut costs and increase efficiencies. Henderson has recently received a state of the art wet shotcrete placer, automated its batch plant, fabricated a mobile concrete form jumbo and is soon to receive a new concrete transport truck.

Jan 1, 1992

By B. Sameti

Blast engineers have been taking advantage of image-based rock fragmentation analysis methods for the past 3 decades to estimate rock size distributions. These methods utilize a wide range of image segmentation techniques, from manual to fully-automated, to delineate the edges of rocks in images. Rock delineation results are then converted to physical rock sizes (and percentage passing curves) by scaling the image pixels to correspond to physical measurements. The size scaling process is critical for acquiring physical measurements, but specific to the limitations of different applications. This article starts by presenting a shovel bucket-based fragmentation analysis system, where scaling is done using the known width of the shovel bucket within the image. Next, it describes methods that use pictures captured by digital cameras with scaling reference objects in the view. Finally, the article presents a method that uses three-dimensional imaging to capture images without the need for scaling reference objects. A portable device which utilizes a three-dimensional imaging method is proposed, and compared with the other methods. The proposed solution combines the generated three-dimensional points with the delineated rock boundaries in the image to reconstruct the surface, and generate accurate rock size estimates and percentage passing rock size distributions. System operation is described and its accuracy and performance are discussed for various scenarios. It is shown that since the device does not require a physical object for scaling reference, it is free from the limitations of other methods, and can be applied for automatic rock size measurement from various sources such as mining shovels, loaders, crushers, stockpiles, haul truck beds, and conveyor belts.

Feb 23, 2014

This paper examines the feasibility of combining network modeling and computational fluid dynamics for modeling of underground mine ventilation systems. Both simulation methods have specific advantages and disadvantages for analysis of mine systems. Network modeling is widely utilized by many operations and allows for assessment of current systems and simulation for planning purposes. Alternatively, CFD has been utilized only marginally by operations and is typically a research tool, requiring considerable computational power, complex models, and careful analysis and calibration of results. Network modeling allows for a holistic approach to the ventilation system, giving quantity, velocity and pressure in every branch, but CFD modeling can resolve the flow regime in 2-D or 3-D, which is idea when examination of an area on a more detailed basis is useful, such as dust and gas control. Integration of the two can allow for more flexible systems analysis. The feasibility of integration, along with application to limited underground mine data are examined.

Feb 23, 2014

By J. P. McDonald

Exposure to particulates containing metals and metal fumes (PCMMF) is a potential concern in ore refining and smelting. Some metals of primary interest are arsenic, cadmium, copper and lead, which have been linked to various adverse health effects. The current National Institute for Occupational Safety and Health (NIOSH) sampling method for metals in particulates requires the use of a filter, precision airflow pump and laboratory analysis. A major concern with this method is the one-to-two weeks? wait before laboratory results are available for use in determining if additional controls are needed to assure adequate exposure protection for workers. Particulates containing these metals were sampled during sixteen sampling events at a copper smelter using the traditional NIOSH methods. Monitoring of particulates was simultaneously conducted using a TSI 8520 Dust-Trak real-time aerosol monitor with a 10-µm-cutpoint sampling inlet. NIOSH analytical methods related to particulates and metals (methods 0500, 0600 and 7300) were used to determine particulate mass and individual mass contributions of metals on sample filters. Linear regressions with y-intercepts forced to zero were developed to determine the relationship between the PM10 measurements recorded by the DustTrak and laboratory-reported total particulate mass, PM10 and respirable arsenic, cadmium, copper and lead concentrations. These linear regressions yielded correction factors that can be applied to DustTrak readings to obtain total particulate mass, PM10 and respirable concentration estimates for each of the four metals. The R2 (coefficient of determination) values from the linear regressions ranged from 0.65 for total lead to 0.91 for total copper. These results suggest that the DustTrak may produce real-time data useful in providing estimates for airborne concentrations of arsenic, cadmium, copper and lead in copper smelter particulates.

Jan 1, 2011

By F. Habashi

The Republic of South Africa is a heterogeneous mixture of Black Africans, Afrikaans, British, Indians, Malayans, French Huguenots, and many others from Europe and Asia. A decisive date in its recent history is the collapse of the Apartheid Regime in 1994. For a metallurgist, South Africa is the country of diamonds, gold, platinum, and many other metals. In 1887 Cecil Rhodes (1853-1902) was able to take control of the De Beers Mining Company after the discovery of diamonds at Kimberly in 1866. It was there where the so-called School of Mines was inaugurated in 1896.

Jan 1, 2010

By Roy H. Patten

When driving a shallow soft ground bore, the appearance of surface craters along the tunnel alinement indicates trouble, particularly when a major highway is intersected. During the excavation of a 3.7 m diam tunnel in Seattle, Washington a chemical grouting program was implemented to stabilize soil conditions sufficiently to allow advancement of the mole without loss of ground. Unanticipated mixed face conditions consisting of saturated running sand and some boulder pockets bedded on top of dense glacial till created excavation difficulties. A discussion of problems and corrective measures is presented.

Jan 1, 1987

By C. E. Jordan

The fundamental properties of the Bureau of Mines patented dielectric separator were studied to provide insight regarding its design and operating characteristics. Force equations for mineral particles were derived and evaluated experimentally. High dielectric mineral recovery was proportional to the calculated effective dielectric force volume that surrounded each drum electrode wire. Electrode spacing was the most sensitive design parameter, requiring less than 0.4-cm electrode spacing for a good separation. Operating characteristics and ore characteristics were investigated. With a dielectric constant difference as small as 2, good separations were made on a laboratory scale at energy consumption below 12 kw?h/mt.

Jan 1, 1985

By C. R. DeGennaro, M. R. Girman, J. Bickson, J. P. Homer, C. C. Jobes

Between 2005 and 2021, a NIOSH internal review showed that haul trucks were involved in 54 incidents at surface mines in the United States. Haul truck collision warning and avoidance systems (CXS) can assist in preventing accidents at surface mines. CXS use technologies to detect people or objects and alarm to alert haul truck operators. Robust testing can help ensure that they detect objects without excessive false positive alarms. Testing and validation would increase confidence in and encourage implementation of a CXS. Researchers from the National Institute for Occupational Safety and Health (NIOSH) reviewed documents related to the evaluation and validation of CXS with two objectives: (1) to identify methods and parameters used to evaluate detection performance and (2) to identify gaps in CXS test methods and in detection performance. Stakeholders can use the findings from this research to guide implementation of CXS to improve safety at surface mines.

Mar 2, 2022

By Carl-Eric Dr. Nilsson

Energy cost for mine ventilation in Sweden is high, especially during winter time when air must be heated. This paper presents the result from a project entitled ventilation-as-required. The term ventilation-as-required means that the required volume of fresh air should be distributed only to such areas, where mining work is going on and to be reduced to a minimum in the rest of the mine. Ventilation-as-required is a monitoring system that controls the operation and capacity of the fans and measure the air pollutant gases, i.e. carbon monoxide, nitrogen and sulphur dioxide at strategic points. It is an active system that responds when equipment is under operation. MITU proposed in 1991 a project to develop a ventiation-as¬required system and such components as transmitters and receivers for the communication between the equipment and the fans. The mining companies, Boliden Mineral AB, LKAB, Outokumpu and Ammeberg Mining Corporation joined the project and have financed a joint research and development programme supported with a grant from the Swedish Government through NUTEK. MITU proposed a second project in 1992 to the mining companies to develop an improved "intelligent" fan for scope ventilation. Boliden Mineral and LKAB joined the project and have financed a joint research and development project supported by the Swedish Government through NUTEK. The Government even made a commitment to support the investment of the first 50 fans ordered with a grant of 25% of the investment cost. The result from projects show that the target set up in the plans is more than achieved, with an energy reduction that exceeds 30% compared to previous consumption. No environmental influence due to reduced ventilation is observed in the stope when work is under progress. Dilution of exhaust gases from diesel fuel decreased from 6.000 m3/L consumed diesel fuels to 3,600 m3/L. The automatic data processing and sensor system is even increasing the security of the work so that it can be done under safer environmental conditions.

Jan 1, 1995

By Rob Thomas

It is generally agreed that standing support should be installed in roadways that will for various reasons, be holed through with a longwall. Considering the magnitude of the associated abutment loading in conjunction with the need to ensure that the material used is cuttable, some form of cementitious support is often used.

By Caroline Gerwig, Joseph R. Wickline, Zach Agioutantis

In longwall mining, the progressive caving of the roof allows stored energy to dissipate over an extended time. However, in some cases, the roof strata above the longwall panel are unusually strong and do not break with the movement of the working face. Instead, the roof material bridges over the expanse of the longwall, forming an unstable beam. Later, when this beam breaks, the stored energy can release suddenly, causing a seismic event to propagate to surrounding mine workings. The focus of this paper is to estimate the size of beams that form over longwall panels to the seismic energy recorded by the mine. Analytical calculations are used to verify two-dimensional models of longwall roof beams to determine the strain energy and gravitational energy developed, which is then released upon strata failure to surrounding mine workings. Models are developed using RS2 to model the stress, strain, and deflection along the bottom of the longwall roof beam to calculate gravitational and strain energies. Gravitational energy is shown to be the main driving factor in energy release, except for the beams with low heights. Analyses allow the determination of beam characteristics based on seismic data. The analysis is refined using swelling factor to compare various beam drop heights. The models show an increase in seismic magnitude for higher drop heights. However, the actual data provided by the Buchanan mine displays a decrease in seismic magnitude with increasing drop height, indicating that energy is dissipated into the broken gob material as drop height increases.

Jul 1, 2023

By L. Zhou, D. Bahrami

Mine ventilation is one of the most important aspects of mining operations in underground mines. It is critical to maintain and deliver required fresh air to the active areas to reduce the risk of overexposure to hazardous contaminants or explosive atmospheres. An unexpected or unknown event such as roof collapse, unexpected mine door closure/opening, a fire/explosion, or fan malfunction could adversely alter the airflow distribution within the mine ventilation network that could lead to a hazardous underground environment. Knowing the occurrence and location of such an incident is of critical importance. In this study, the authors developed a novel methodology to assist mine operators in quickly identifying the location of any abnormal airflow change within the network using the airflow changes at monitored airways. The concept is based on a direct derivative method developed by the authors. This paper provides the details of the developed method as well as numerical verification examples. The application of this method can benefit mine operators and safety personnel in making better decisions during a mine emergency response operation to mitigate hazardous conditions arising from an unexpected airflow disturbance

Mar 2, 2022

By Dae Young Kim, Sim Bo Kyung, Ebrahim Farrokh, Ki Chang Hyun

"TBM cutter life evaluation in abrasive granitic rocks is a very important issue, especially in pressurized face tunneling with mixshield TBM for which the planning of costly interventions becomes crucial. This paper presents an overview of methodologies for cutter life evaluation in rock. A comparative study is performed to indicate the predictability of cutter life evaluation methods based on detail data from the NS3 tunnel project in Singapore. A new model is developed based upon the cutter wear information of eight TBM tunnels from around the world. New methods are proposed to evaluate the optimum intervention interval length and the number of worn-out disc cutters for a tunnel project. Finally, two new laboratory tests in the evaluation of disc cutter abrasion, including a full-scale and a small-scale test, are introduced, and their test results are discussed. INTRODUCTION The issue of wear evaluation for hard rocks has been extensively studied in drilling and pavement industry. In this regard, several tests and evaluation methods have been proposed to estimate or evaluate the state of tool life (e.g. bit life for drilling). In the case of TBM tunneling, tool wear may depend on several factors such as mineral composition, strength, or type of cutting, but as the abrasion is usually the major mechanism for the tool wear in hard rock, the developed methods for cutter wear or cutter life evaluation are mostly based on the abrasion indices such as Cerchar Abrasivity Index (CAI). This paper attempts to review the major methodologies for disc cutter wear and life evaluation and to propose new methods to evaluate cutter life and intervention interval evaluation based on detail information of a mixshield tunnel project in Singapore as well as general information of some other projects from Iran, Italy, South Africa, and France. As the laboratory tests are crucial in the process of evaluation, two new lab tests are developed and used to inspect suitability of the new proposed model for disc cutter wear evaluation."

Jan 1, 2016

By W. D. Keller

Scan electron micrographs, SEM's, will be shown of representative refractory clays from Missouri deposits, with counterparts from other localities. The story is in the pictures, ("1000 words in each picture"), but clay types include the following. Plastic, semi-plastic, and semi-flint "fire clays" of Missouri have textures which appear to retain certain relic texture of ball clay. Flint clay is composed of tightly interlocking packets, sheaves, and books of kaolinite. Diaspore and boehmite mineral textures characterize those "clays". Surface-boulder diaspore shows very pronounced recrystallization and crystal enlargement from original, unexposed first-grade diaspore.

Jan 1, 1977

By F. Ansheng

Though it becomes increasingly important with the valuable minerals in their deposits tending to be fine and poor, the solid and liquid separation remains difficult especially when the particles are of micrometer size and of low density. Almost of all conventional thickeners result in that fine particles lose into overflows which often costitutes a loss of potentially valuable resources as well as an environmental hazard. The addition of flocculations may improve the settling of solids but may also not work well for the final removal of fine particles from the overflows (Ref.1).

Jan 1, 1990

By James H. Barks

Commercial development of the mineral resources of southwestern Missouri began about 1850 and spread into southeastern Kansas and northeastern Oklahoma, forming the Tri-State Mining District with Joplin as the urban center (fig. 1). The value of the Tri-State mineral production from 1850 to 1950 exceeded one billion dollars, and until 1945 the region was the world's leading producer of lead and zinc concentrates, accounting for one-half of the zinc and one-tenth of the lead produced in the United States (Gibson, 1972 1). By 1950 most of the rich ores had been extracted, and mining and milling operations declined during the 1950's and ceased in the 1960's. The sulfide minerals, mainly galena and sphalorite, were mined from cherty limestones at depths of 25 to 75 m (meters). Crude ores were brought from the mines to the surface where they were milled into lead and zinc concentrates. , Barren rock was discarded in piles while the ore-bearing rock was crushed and ground into fine gravel. The minerals were separated from the rock by a jigging process and the tailings were skimmed off and discarded in large piles. Ground-water flooding of the mines was controlled by constant pumping. When pumpage declined in the 1950's and 1960's tile abandoned mine drifts and shafts filled with water. At present (1977) numerous tailings piles and flooded mines remain as visible evidence of the mining era and as a threat to the quality of ground and surface waters of the area. In 1976 the U.S. Geological Survey in cooperation with the Ozark Gateway Council of Governments made a study of the effects of the mines and tailings piles on water quality in the Missouri part of the Tri-State District. The study area covers approximately the southwestern quarter of Jasper County, an area of about 725 km2 (square kilometers), and is bounded by long 94 o 15' w.' and the Missouri-Kansas state line, and lat 37 o 15 N., and the Jasper-Newton County line.

Jan 1, 1977

By Hugo E. Camargo, Amanda S. Azman, Brian Kim

Repeated noise exposure and occupational hearing loss are common health problems across industries and especially within the mining industry. Large mechanized processes, blasting, grinding, drilling, and work that is often in close quarters put many miners at an increased risk of noise overexposure. In stone, sand, and gravel mining, noise is generated from a variety of sources, depending on the type of ore being mined as well as the final consumer product provided by that mine. Depending on the source of noise generation, different strategies to reduce and avoid that noise should be implemented. The National Institute for Occupational Safety and Health (NIOSH) has evaluated the noise profile at three operational surface stone, sand, and gravel mines. A-weighted sound level meter data as well as phase array beamforming data were collected throughout the mines in areas with high noise exposure or high personnel foot or vehicle traffic. Sound level meter data collected on a grid pattern was used to develop sound profiles of the working areas. These sound contour maps as well as phase array beamforming plots were provided to the mines as well as guidance to modify work areas or personnel traffic to reduce noise exposure.

Jan 6, 2022