Search Documents

By Van Price

Some technical developments of the National Uranium Resource Evaluation Program which are of general application in geochemical exploration are being studied. Results of stream water and suspended and bottom sediment analyses are compared for an area near Williamsport, Pennsylvania. Variations of uranium content of water samples with time in the North Carolina Piedmont are seen to correlate with rainfall. Ground water samples from coastal and piedmont areas were analyzed for helium. All media sampled provide useful information when properly analyzed and interpreted as part of a total geological analysis of an area.

Jan 1, 1979

By William G. Freeman

In comparison to many mineral commodities, barite has a low unit value. It is mined and sold in low volumes in high-grade (90-98% BaSO4) forms to basically one industry that uses approximately 75% of the free world production. Based upon the above criteria, all factors must be considered in determining if a barite deposit is economical; such as, the type of deposit, mining and milling methods required, transportation to the markets, tariffs, local political conditions, etc. In other words, barite mines are made--not found. The length of this paper precludes any indepth discussion of geology, mining and metallurgy of barite. Most of this information can be found in data already published, such as D. A. Brobst's bulletin1 on the Barite Resources of the United States.

Jan 1, 1971

By Brian Fulcher

The Fort Lawton Parallel Tunnel was built in 1990 - 1991 by Morrison Knudsen Corporation (MK) as an integral part of Seattle METRO's planned expansion of the Westpoint Treatment Plant. The project included a concrete lined 2542 m (8,340 ft) long tunnel bored in sands and clays under the presence of methane gas and over 27.4 m (90 ft) of ground water table. The tunnel roughly paral¬lels an existing and still operating 3.65 m (12 ft) diameter tunnel originally completed in 1909. The parallel tunnel was constructed using a Lovat 4.72 m (15 ft-6 in) earth pressure balanced TBM with ribs and timber lagging as primary support. The tunnel alignment crossed under as much as 91.4 m (300 ft) of overburden as well as twin mainline railway tracks; terminating in a shaft adja¬cent to the Seattle ship canal. The project was completed in June, 1991 after a final "wet-tap" tie-in to the existing brick-lined sewer; over five months ahead of the contract schedule. This paper will describe the construction methods, job site conditions and difficulties encoun¬tered on this very challenging and successful project.

Jan 1, 1993

By William J. Maloney

Blind drilled shafts are becoming increasingly popular as a secondary and sometimes primary means of ventilation. This is particularly true in the Appalachian coalfields. Some reasons for the rebirth of blind shafts are economics, timeliness, safety characteristics and their inherent independence from underground operations. Blind drilling has had limited use in hard rock and tunneling ventilation. Advances in cutters, bit design, equipment and lining systems have made blind drilled shafts the shaft construction technique of choice for ventilation specialists. History of blind drilling Blind drilling's roots include the Nevada test site, the coalfields of Appalachia and Germany, and the uranium mines of Arizona. Early technology was developed using a variety of equipment mainly of oilfield origin. Shafts completed by oilfield equipment ranged from the shallow 1.5 and 1.8 m (5 and 6 ft) lined shafts on the Nevada test site to two 3 m (10 ft) lined, 222 m (730 ft) deep shafts in Alberta for heavy oil development. Several of these shafts were completed to extraordinary depths. The record, completed in 1969, is a 2.28-m-diam (90-in.-diam), 1875-m (6150-ft) deep shaft, located in the Aleutian Islands of Alaska.

Jan 1, 1993

By Antonieta Middea, Rupen Adamian, Fernando F. Lins

This work presents the results obtained with aggregation of fine talc (-19 m), a naturally hydrophobic mineral, in the presence of KC1 solutions. The classical DLVO theory describes well the aggregation of talc in dilute KC1 solutions. Beyond 1 M KCI we have found indications that a non-DLVO interparticles force is operative, say an hydration (repulsive) force. This structural force could be responsible for the unexpected re-dispersion of talc suspension. However, no repulsive force (depression) has been observed in salt flotation of talc at higher ionic strength, up to 3 MKCI.

Jan 1, 1995

How do you think the US Bureau of Mines closing will affect SME? The demise of the bureau represents a challenge, an opportunity and, above all, new responsibilities for our profession. A lot of good professionals are seeking new positions. A lot of worthwhile research is available for transfer to the private sector. Logic dictates that worthwhile projects of any defunded government activities should find support in the private sector. The bureau may be gone but its legacy is deeply rooted in the profession. The bureau’s contributions will be remembered as long as there are mines and miners. Its1994 research program was divided into three major areas: environ-mental technology; health, safety and mining technology; and minerals and materials science. There must be a place in either the government or private sector to continue these worthwhile activities.

Jan 1, 1996

Lignite is a kind of easy-to-slime and low rank coal. It is hard to be separated by the conventional wet coal beneficiation technologies. Meanwhile, in recent decades, a large amount of fine coal (-6 mm) is generated as the mechanized mining technology has been progressively deployed in coal sector, which causes a great difficult for lignite beneficiation and upgrading due to lack of efficient technology available. In this paper, a vibrated gas-fluidized bed was used to separate the -6 mm fine lignite particles. Separation experiments of -6+3 mm and -3+1 mm lignite were carried out in a laboratory-scale vibrated gas-fluidized bed. The effects of several parameters including the superficial air velocity, vibration intensity, bed height and exterior moisture content on the separation performance were experimentally studied. The results show that the optimal separation performance was achieved when the superficial air velocity is 0.3, the vibration intensity is 1.4, the bed height is 50 mm, the exterior moisture content is below 4% (-6+3 mm) and 2% (-3+1 mm). And the probably error E values of -6+3 mm and -3+1 mm size fraction of lignite are 0.202 and 0.225 respectively. The results indicate that a vibrated gas-fluidized bed can provide an effective solution for -6 mm lignite separation.

Feb 23, 2014

By Nathaniel Arbiter

A fully-instrumented driving mechanism has been constructed to study the power, aerating and solid suspension characteristics of several laboratory flotation machines. Machines operating over normal flotation speed ranges give constant power numbers in liquid' systems indicating that they operate under fully baffled turbulent flow conditions. Owing to lack of geometrical scaling, power numbers for different sizes of cells of the same make are different. Even larger differences occur between cells of different manufactures. For a given impeller, varying the tank size did not significantly affect the power consumption. Tank geometry and baffling has a slight effect on power consumption with shrouded impellers. For a given impeller speed, suspension height decreases while power increases with increasing mass of solids in suspension. While power consumption is hardly affected by particle size and clearance between the impeller and tank bottom, the suspension height significantly increases as clearance increases and as particle size decreases. Aeration was found to affect not only power but also the suspension characteristics of the machine. For closely sized particles drastic sedimentation occurred when a critical value of the air flow number was exceeded. The critical air flow number decreased with increasing particle size. This effect was less marked with a wide particle size range. The self-aerating capacity of flotation machines increases with cell size at a given speed for the same impeller-shroud system, but decreases in the presence of frother and solids. Equations have been established for correlating all of the studied variables. Data taken from the literature were also correlated with these equations.

Jan 1, 1968

By J. J. Gusek

Passive treatment of mine drainage using constructed wetlands has been employed on coal and metal mine sites since about 1985. The technology has advanced significantly since then; there are currently over 600 of these systems treating coal mine drainage in the Eastern U.S. at flow rates of hundreds of liters per minute. Passive treatment performance at three metal mines discussed in this paper has been positive for a wide variety of flows, water chemistry, and climates. The sites include a high-altitude underground copper mine, acidic seepage from a gold heap leach pad, and pumped effluent from an active underground lead mine in Missouri.

Jan 1, 2000

By A. H. Srnallbone

Over the past few years the rising production costs, shortage of skilled labor, and increased use of lower grade ore bodies have all added justification for the use of on-stream analysis. A rise in the number of on-stream units indicates that this type of assay is now being accepted as a necessity. On-stream analysis is a much more rapid means of obtaining true assays of a flowing product when compared to wet chemistry or "grab" samples dried, briquetted and assayed by x-ray. In contrast, on-stream analysis uses real time samples assayed every 30 seconds while each stream is assayed every 5 to 15 minutes. It is very important not only to know that a change has occurred in the process, but to know what caused the change and how to correct for the change. For example, in a tailing sample the elements of interest comprise between 1% and 10% of the sample. The remainder is water and gangue. Previously the gangue was not assayed nor were the low atomic number elements used for corrections. In addition to the demand for higher accuracies some concentrators were being penalized for excessive Ca or in some cases 5i in their concentrates. This penalty was being imposed by the smelter in order that they could better cope with pollution problems and prolong the life of their furnaces. But until Ca, 5i, and S are measured on-line, nothing can be done about their control. By accurately measuring these light elements on-line, a complete assay is obtained of the total sample providing improved accuracy for the important products. The justification for complete accuracy assays is now even more obvious because they are possible at very 1ittle increased cost and at no increase in analytical time.

Jan 1, 1977

By W. C. Hirt

Deposits of ferromanganese crust containing cobalt and nickel occur on the seafloor in the Pacific Ocean near the Hawaiian Islands and Johnston Atoll. This paper describes developmental flotation metallurgy to separate crust from its associated substrate gangue. Important variables in ferromanganese crust flotation include reagent type, aeration rate, conditioning time and agitation intensity, pH, temperature, water type, and feed size distribution. Flotation in seawater of minus 600 ~m (-28 mesh) material assaying 6.2% Mn, 0.2% Co, and 0.13% Ni with diesel fuel-crude tall oil-sulfonate collectors produces concentrates assaying 15% Mn, 0.6% Co, and 0.3% Ni with recoveries of 89-95% while removing 62% of the feed weight.

Jan 1, 1990

By Gurses Oner

In situ leaching is a relatively old mineral extraction method; however, historically only a small portion of copper has been produced from small scale operations. Recently, in situ leaching technology because of its intrinsic advantages over conventional mining and milling is being considered as a viable option for recovering copper from both low grade oxide and sulfide deposits. This paper presents the application of computers to investigate in situ technology using large whole core leaching experiments. Computers were applied to three different areas: (1) experimental control and data acquisition, (2) non-destructive evaluation of samples using x-ray computed tomography and image processing and (3) mathematical modelling and data analysis.

Jan 1, 1992

By Bradley S. Van Gosen, Anjana K. Shah, George M. Bedinger, Donald I. Bleiwas, Karl J. Ellefsen

"Ancient and modern coastal deposits of heavy mineral sands (HMS) are the principal source of several heavy industrial minerals, with mining and processing operations on every continent except Antarctica. For example, HMS deposits are the main source of titanium feedstock for the titanium dioxide (TiO2) pigments industry, obtained from the minerals ilmenite (Fe2+TiO3), rutile (TiO2) and leucoxene (an alteration product of ilmenite). HMS deposits are also the principal source of zircon (ZrSiO4), from which zirconium dioxide (ZrO2) is obtained for uses mostly in refractory products. Sometimes monazite [(Ce,La,Nd,Th) PO4] is recovered as a byproduct mineral, sought for its rare earth elements, and thorium (Ault and others, 2016; Sengupta and Van Gosen, 2016; Van Gosen and Tulsidas, 2016).HMS are sediments containing dense (heavy) minerals that accumulate with sand, silt and clay in coastal environments, locally forming economic concentrations of the heavy minerals (Fig. 1). Economic (mined) HMS deposits include Holocene sediments on modern coasts, such as examples in India and Brazil, as well as coastal deposits formed by transgressions and regressions of the seas during intervals in the Quaternary, Tertiary and Cretaceous, such as in Australia and the southeastern United States. Economic deposits typically contain heavy-mineral concentrations of at least two percent. Individual heavy minerals are commonly defined as minerals with a specific gravity greater than approximately 2.9 g/cm3. These minerals are generally resistant to chemical weathering and physical degradation and thus survive well in fluvial and coastal environments. Heavy minerals in coastal HMS deposits may include, in order of general abundance, ilmenite, leucoxene, rutile, magnetite, zircon, staurolite, kyanite, sillimanite, tourmaline, garnet, epidote, hornblende, spinel, iron oxides, sulfides, anatase, monazite, cassiterite and xenotime. Of these, ilmenite, leucoxene, rutile and zircon are the primary economic minerals. Garnet, monazite, cassiterite and xenotime are occasionally recovered as byproducts. The heavy minerals as a suite typically make up no more than 15 weight percent of a deposit and usually much less. Quartz and clay minerals form the bulk of the sediment. The geology of HMS deposits and examples of significant districts are summarized in Van Gosen and others (2014) and Hou and Keeling (2016)."

Oct 1, 2016

By P. W. Hunter

The construction of a major sewerage scheme requiring 15.3 km of 5.5m excavated diameter tunnel in basalt, mixed and soft ground has been undertaken by the Melbourne and Metropolitan Board of Works. A double shielded Tunnel Boring Machine was selected to excavate 13.7 km of basalt and mixed ground. Advanced methods for recording operational data on the TBM were introduced. Progress to date has shown that the TBM can excavate rock very effectively with a best weekly production of 178.8m; soft ground has been encountered and successfully handled.

Jan 1, 1987

By Ann M. Hagni

One of the most costly factors in the production of aluminum is the consumption of energy in the form of electricity. Energy consumption is increased as refractories in the Hall-Heroult reduction cells are corroded by penetration of the fluxes cryolite (Na3AlF6) and villiaumite (NaF). To decrease thermal conductivity and refractory waste, protective barrier linings are installed. Dry powder barrier linings form stable reaction products at cell operating temperatures. Four dry powders composed of vermiculite, corundum, wollastonite, and anorthite are characterized mineralogically by X-ray diffraction, reflected light microscopy, scanning electron microscopy, and cathodoluminescence microscopy in this research project.

Jan 1, 1998

By M. B. Mirza, W. A. Sadik, B. T. Stanley

This paper presents the ventilation design for an underground testing facility in a salt medium. The under-ground workings consist of two 3.6 m-diam (12 ft-diam) watertight shafts and about 1830 m (6000 ft) of drifting. These facilities are designed to provide access for an in situ testing of a salt horizon in which a variety of hazardous and nonhazardous materials could be temporarily stored or permanently deposited. The ventilation system includes a design basis for gassy mine conditions and provides for the option of bulk air cooling and heating.

Jan 1, 1987

By E. J. Rorem

Rockfall and unstable rock slopes can be con-trolled by using steel wire-rope net systems as barriers or as slope draping. The chief advantage of such systems over rigid type barriers is the flexibility of wire rope netting. This flexibility and strength permits kinetic energy dissipation with low maintenance requirements. Mining activities can produce temporary or long-term unnatural slopes and unstable rock faces that may produce rockfall hazards. Such conditions can necessitate efforts to minimize the hazard to workers, structures and equipment.

Jan 1, 1996

By Siegmund Babendererde

1. Introduction In Sayreville, New Jersey, the Middlesex County Utilities Authority put the construction of a 1041 m long sewer outlet to tender in June 1989. It had an internal diameter of 3,36 m and was part of a sewage treatment works project for county Middlesex. The contract was awarded to the Lodigiani Company, USA, who employed Hochtief Incorporated as subcontractor to drive the sewer outfall. 2. Ground Conditions According to the preliminary geological site investigation, carried out by the consultants Metcalf & Eddy, the tunnel passed through marine deposits.

Jan 1, 1991

By Robert L. Frantz

The U.S. Bureau of Mines (USBM) established on August 15, 1983, a Generic Mineral f Technology Center (GTC) for Respirable Dust within the Mining and Mineral Resources Research Institutes (MRIs) at The Pennsylvania State University (PSU) and West Virginia University (WW) in association with participating MRIs at Massachusetts Institute of Technology (MIT) and the University of Minnesota (UMN). The primary goal of the Center is to reduce the incidence and severity of respirable dust disease through researching and advancing the fundamental under- standing of all aspects of respirable dust associated with mining and milling and the interaction of dust and lungs. Other Center activities include the training of engineers and scientists, graduate students and undergraduate students through their respective institutions, and the technology transfer to the industry. The Center also serves as the reference center for publications in the respirable dust area.

Jan 1, 1986

By C. West

Structured or embossed HDPE and LLDPE geomembranes have been available to mine owners and designers for over ten (10) years. As many owners and designers discover and demand the consistent high quality characteristics of this type of geomembrane due to the unique manufacturing process, the use of these materials in new mines, mine expansions and final closure designs has steadily increased. Structured liner materials are available for double lined and final cover systems and are revolutionizing the way ponds, pads and final closures are constructed. This paper will discuss the structured or embossed geomembrane concept and manufacturing process. Additionally, the paper will present comparative testing illustrating the major advantages of using this type of product in these types of applications. Both technical and economic advantages are illustrated. The cost savings include lower installation costs, less material used, and third party inspection times not to mention better performance. These new systems will be presented.

Jan 1, 2011